Search Documents

By Marco A. Vera

"This paper investigates the froth function in flotation and the associated upgrading process. Flotation literature has revealed that one of the main functions of the froth phase is the cleaning of bubble-particle aggregates by rejection of entrained material. The cleaning and transport processes across the froth phase exert straining forces on these aggregates on their way up to the froth surface. These forces will impact on the recovery of bubble-particle aggregates.The grade at the top of the froth (TOF) is a parameter related to the quality of particles collected by bubbles in the pulp zone (true flotation). It has recently been demonstrated that TOF corresponds to the maximum practically attainable grade described by the recovery-grade (or enrichment ratio) curve. TOF lumps all the processes experienced by the bubble-particle aggregates before reaching the launder concentrate. This paper describes a methodology for quantifying flotation performance by means of the top of the froth sample - a touch of froth.INTRODUCTIONFroth flotation may be the most important mineral processing technique, but its theory is complex and is not completely understood even though many aspects have been studied and reviewed (Teague, 1998; Wills, 1992).Two distinct particulate systems prevail in the flotation process: a pulp phase and a froth phase (Figure 1). The pulp zone had been studied extensively; however, it is only recently that techniques to measure the froth zone performance have been developed (Contini et al., 1988; Falutsu and Dobby, 1992; Feteris et al., 1987; Seaman, 2002; Vera et al., 1999b).Flotation involves a number of mass transfer processes, occurring in the pulp phase and the froth phase. The formation of the froth and its subsequent removal are considered to be two important steps of the process. Phenomena that occur in the froth phase are known to affect flotation performance significantly (Cutting et al., 1981).Because the froth has a high free surface energy (as a result of the extensive interfacial surface between liquid and air), it appears thermodynamically unstable. The foaming is a dynamic balance, as new bubbles are added continuously from the pulp, while others disappear from the top. Under steady-state conditions, the volumes of added and subtracted air are equal (Booth, 1953)."

Jan 1, 2003

By G. S. Austin

New Mexico produced 83% of domestic potash and 27% of domestic consumption in 1992. The potash industry of New Mexico produces sylvite (KCI), langbeinite (K2SO4-2Mg(SO4)2), and artificial K2SO4. Average sylvite grade in New Mexico today is about 14%. The average grade of langbeinite is 8-10% Kp. Commercial potash occurs in the middle or McNutt Member of the Salado Formation (Upper Permian Ochoan Series). The 120-m-thick McNutt Member dips about 1° east and contains 11 of 12 potential ore zones in the Salado. The mineralogy and proportion of clay minerals, up to 7% of the ore, influence optimum milling procedures and ore grade cutoff.

Jan 1, 1994

A wide range of drill holes and process streams are sampled for resource estimation, grade control and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2009

By Jonas Olsson

"The picture of China as an antiquated continent is changing rapidly and fast-forwarding progress is a fact in most infrastructural fields. Mining is not an exception. China is today the largest producer of aluminum, coal, steel, zinc, tin, lead and manganese and the country’s mineral resources comprising approximately 12% of the global reserves ranks them number three in the world after US and Russia.In order to feed the growth industry is needed to take extra ordinary strides to improve supply of raw material and Chinese mines are continuously being upgraded with the latest western technology to meet the increasing domestic demand of base metals.In Anshan located in China’s northeast province Liaoning we find one of the fastest developing mining companies, Angang Iron & Steel Group Co. Ltd. With their six mines that together process approximately 60 M ton iron ore/year Angang Iron & Steel Group Co. Ltd is the largest iron ore company in China. The group’s thorough pre-studies and technical evaluations over the past five years have made them very successful in both plant upgrades of existing operations and green field projects.INTRODUCTIONWe live in a time when the world market is gradually acclimatising to the global consequences of “The China effect”. An effect caused by a formerly sleeping giant nation that during the last years has awakened and developed beyond comparison, primarily because of booming infrastructure projects and demand for capital and consumer goods"

Jan 1, 2006

By William D. Oder, Seth H. Hamblin, Les R. Chernatskas, Jonathan L. Ernst

Large diameter drilled deep foundations are a widely utilized solution throughout North America and the world. Numerous design and construction techniques developed over the past 100 years have made this type of foundation a robust, reliable, and efficient foundation option to support a wide variety of structures. From bridges, to marine structures, to high-rise buildings, drilled shafts are a time-tested approach for all types of infrastructure projects. Yet, what remains ambiguous in the current state of engineering practice is how to respond when a shaft is constructed that, for potentially different reasons, may or may not meet the design requirements? In this case, what are the best practices for Contractors and Engineers when a structural, geotechnical, or material integrity issue arises during construction? In our experience the answers to these questions are not widely known, but are profoundly important so that engineers can have tools available to confidently and efficiently address concerns, and provide a path forward for the project. This paper seeks to answer the above questions by presenting details of different remediation approaches using the results of several case studies where structural and geotechnical engineering methods, combined with non-destructive integrity testing (NDT), were employed to evaluate the acceptance of “questionable” drilled shafts. Through multidisciplinary techniques like Cross-hole Sonic Logging and 3-D Tomography which enhance the resolution of anomalous zones and defects in concrete, the development of concrete strength estimates from non-destructive testing data, and executing innovative structural and geotechnical analyses to evaluate the as-built conditions, drilled shafts that might have historically been rejected were ultimately accepted by the project team. This paper presents a series of unique case studies that together depict a roadmap for a comprehensive approach to reliably evaluate and guide the industry to address these types of drilled shaft construction issues.

Oct 1, 2022

By L. A. Cornish

Pt-based alloys for high-temperature applications in aggressive environments have been under development for over 10 years, and are targeted to be used as either as bulk, or as coatings. The alloys comprise Pt, Al, Cr, and Ru, and the microstructure has been improved by composition to a best possible analogue of the nickel-based superalloys, which these alloys could partially replace. This was necessary because the previous best alloy had a strengthening precipitate volume proportion of only approximately 40 vol.%, whereas the nickel-based superalloys have around 70 per cent, and a lower volume would mean that the strength would not be the best that could be obtained. The microstructures were assessed using electron microscopy, and have been related to the alloys? hardness values. The current microstructures are much more like those of NBSAs, with a high proportion of the strengthening ~Pt3Al precipitates. Since the samples have to be small (platinum is expensive), hardness has been used as an indication of strength. Nano-indentation studies showed that the hardness and Young?s modulus were higher for ~Pt3Al than the (Pt) matrix. More extensive oxidation studies have been undertaken on the previous optimum sample, and the effect of cooling rate after heat treatment has also been ascertained. In addition, the samples were studied after different heat treatment times, and cross-sections were made in order to characterize the alumina scale that formed. The oxide scales of Pt-11Al-3Cr-2Ru (at.%) up to 100 h exposure did not spall, and were at least as good as those of the ternary alloys. There was no discernable Al depletion zone in the substrate, although it could have been at a greater depth than thickness of the samples studied. Further additions to the Pt-Al-Cr-Ru alloys have been studied, to increase the melting temperature as well as to reduce the platinum content without compromising the properties. Reduced platinum content would have the benefits of reduced density and cost. The target elements include vanadium and niobium, of which vanadium is of special interest, since it is a South African product. Before these additions could be made, phase equilibria studies were undertaken so that the maximum addition could be ascertained, and also to check any possible ternary phases, which could be deleterious. Work on the Pt-Al-V system revealed a ternary phase, ~V27Pt54Al19 (at.%), which has a eutectic reaction with (Pt). The maximum V addition is likely to be around 15 at.%, otherwise ~Pt3V or the ternary phase will form, and not the required (Pt)/~Pt3Al phases.

Jan 1, 2012

In 2009 Newmont Mining Corporation?s annual global spend on grinding media reached $94M USD, having doubled in the five years since 2004. The major contributing factor to the spend escalation during this period was unit consumable price, with total media consumption also rising as a function of annual ore tonnes milled. In an effort to better understand and manage the growth of this expenditure a significant supply chain management program was implemented. This was complemented by a series of technical initiatives focussed on grinding media specifications, quality management and the prediction of grinding media wear rate as a function of physical ore characteristics. This paper discusses the methodology and outcomes of these activities.

Jan 1, 2012

By James J. Olson

Most of the projects summarized in this paper are funded under the Bureau's Advancing Metal-Nonmetal Mining Technology program and are part of the in situ mining subprogram coordinated at the Twin Cities Mining Research Center. The borehole mining equipment development, are funded under the Bureau's Advancing Coal Mining Technology program, is essential to accelerated progress in the in situ mining subprogram, and some background information on this concept is included. The initial in situ research projects started in 1971-72 evaluated some of the critical blast design parameters for in situ copper leaching. The present program totals about $1 million per year and includes in-house research projects, cooperative (cost-sharing) projects with the mining industry, and research and development contracts. Two different extraction schemes are under investigation: inplace leaching and borehole (or slurry) mining. The principal commodity targets for the Bureau's improved in situ mining technologies include copper, uranium, coal, and potash. The principal purpose of this paper is to inform the mining industry of the in situ mining research recently completed or being conducted by the Bureau of Mines. In addition the Bureau encourages companies to comment on the program accomplishments as well as offer suggestions on top priority research needs for improving the in situ mining methods described in this paper.

Jan 1, 1977

By D. G. Minnes

Many non-metallic minerals and structural materials are produced in Ontario to serve the needs of domestic manufacturers and export markets. In 1982 production was estimated to have a value of $765 million. Approximately 81 per cent of this was represented by structural materials, nearly 12.8 per cent by salt, and the remainder was other industrial minerals. Total mineral production in Ontario in 1982 was estimated at $3 .16 billion, down nearly $1.5 billion from 1980's high of $4.58 billion.

Jan 1, 1984

By A. J. Naldrett

"Synorogenic mafic intrusions are a common feature of the northern Appalachians. Two sulphide-bearing intrusions in central Maine that have been investigated revealed a number of important features that illustrate sulphide-silicate interaction that relates to magmatic sulphides. The Moxie Pluton is a large mafic intrusion emplaced during the Devonian Acadian orogeny. The Katahdin gabbro is a small mafic body that is probably genetically and temporally related to the Moxie Pluton. Both intrusions were formed bv the intrusion of variably fractionated magmas into irregular chambers and feeder zones. The southern half of the Moxie Pluton contains three small sulphide accumulations, whereas the Katahdin gabbro hosts a large, predominantly massive, sulphide body. Textural evidence clearly documents the magmatic origin of these sulphides.The three Moxie Pluton sulphide bodies are located at or very close to the intersection between the intrusion and the sulphidebearing Hildreths Formation. Sulphur assimilation, suggested by this relationship, is supported by the isotopically light (634S = —8 to —25) and the selenium-poor (S/Se - 25 000-48 000) character of the Moxie sulphides and correlation with the Hildreths Formation sulphides (S34S = —25, S/Se = 25 000-48 000). Isotopically light sulphur (534S = —20 to —21) and high S/Se ratios indicate that the majority of sulphur in the Katahdin sulphide body was also derived from an unexposed country rock source. The volume of sulphide in this example illustrates the potential efficiency of the sulphur assimilation process—so efficient in this case that marked dilution of the economic chalcophile elements resulted from the addition of so much external sulphur.The three Moxie Pluton sulphide occurrences are all impoverished in Ni and Cu (1.87-0.44% Ni; 0.72—0.32% Cu in massive sulphide), but contain normal Co contents (0.22-0.13%) relative to typical magmatic sulphides. The Katahdin sulphides show a greater Ni and Cu impoverishment (0.2% Ni; 0.1% Cu in massive sulphide) with similar Co (0.17%). The Ni content of the Moxie Pluton olivines document the fractional removal of sulphides during crystallization of the host magma, which resulted in the progressive depletion of the chalcophile metals in this magma. Modelling that involved the fractional crystallization of the magma coupled with the fractional removal of a specified proportion of sulphide has successfully duplicated the Moxie Pluton sulphide compositions. A similar magmatic model has been postulated for the Katahdin sulphides with a greater degree of sulphide fractionation. This latter model is again supported by extremely low Ni/forsterite ratios in olivines, though the compositional range is insufficient to document fractionation. These magmatic models are not unique, but they provide a relatively constrained and consistent explanation for the sulphide compositions.The Ni contents of olivines are the most important indicator of sulphide-silicate interaction in mafic magmas and have exploration potential. They provide a means of assessing the timing and extent of sulphur saturation in an intrusion and are a guide to the Ni content of a sulphide accumulation in equilibrium with olivine. In the Maine examples they provide strong evidence of the magmatic origin of the sulphide accumulations and justification for magmatic modelling."

Jan 1, 1984

By Henry Louis

THE work performed by the Royal Commission on Mining Subsidence is likely to prove of permanent value, less perhaps for the conclusions it has reached and for the recommendations it has based upon these than for the admirable exposition which it affords of the law concerning mining subsidence and of the legal status of the person who has suffered damage by reason of such subsidence, as also of him whose working has caused the damage. The Commission was appointed by Royal Warrant in the middle of 1925 and delivered its final report in the middle of 1927. The terms of reference to the Commission were as follows: "To consider the operation of the law relating to the support of the surface of the land, and of buildings or works on or under the surface, by underlying or adjacent minerals; to enquire into the extent and gravity of the damage caused by subsidence owing to the extraction of minerals and the incidence of the resulting liability; and to report what steps should be taken, by legislation or otherwise, to remedy, equitably to all persons concerned, any defects or hardships that may be found to arise in existing conditions."

Jan 1, 1929

By R Wynn, R A. Pax, S Mann, B Cornish

The semi-autogenous grinding (SAG) mill at the MMG Century operation has failing load cells that are essential to the control strategy used to stabilise the mill. Currently, mill-bearing pressure is used as a proxy for the load cells, but it has been found to be a noisy signal and lacking in useful sensitivity. It is also prone to variations and drift due to temperature. After consideration of a number of options, a non-contact acoustic array has been installed around the SAG mill to provide a more stable proxy load signal as well as other information about the internal operation of the?mill.The installation consists of 12 microphones to provide some detail into the operational differences that occur during normal operations at the MMG Century SAG mill. This acoustic approach acknowledges that operational grinding mills emit significant acoustic emissions that are a consequence of the dynamic environment prevailing inside them.Previous studies have attributed the acoustic noise to a range of events that occur inside these mills (Pax, 2011; 2012). Consequently, non-contact acoustic determinations of in-mill behaviour can provide powerful insights into the operation of the primary comminution tumbling mills. By measuring key microphone signal attributes at different positions around a mill, a holistic picture of mill internal operation can be developed.This paper will describe the installation of the 12 microphones and discuss the use of the acoustic load signals as a proxy for failing load cells. It will also present data from new observations of internal mill dynamics and the results of implementation of control using these acoustic signals. Key to the control approach has been the development of a logically coherent picture of the processes inside the mill.CITATION:Pax, R A, Wynn, R, Mann, S and Cornish, B, 2014. Implementation of acoustic arrays for semi-autogenous grinding mill?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 273–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Freeman, the English historian, said that he had learned from Macaulay "never to be afraid of using the same word or name over and over again if by that means anything could be added to clearness or force. Macaulay never goes. on, like some writers, talking about ' the former ' and 'the latter ', 'he ', 'she ', 'it), and 'they’, through clause after clause, while his reader has to look back to see which of several persons it is that is so darkly referred to". He might have learned also from Macaulay that a preposition makes a feeble ending for a serious statement. How often do you hear 'the former' and 'the latter' in conversation? Good conversation is a guide not to be disdained. When you must use 'the latter ', do not confuse it with 'the last '. Cheap labor, cheap fuel, and cheap transport are essential, the latter [last] being particularly important in base-metal mining. The apparatus may be used to determine such gases as hydrogen sulphide, chlorine, oxides of nitrogen and some others, as well as sulphur dioxide. In the case of the latter two, etc. The two last mentioned are "sulphur dioxide" and "some others". He should have stated which two, and he should have avoided that wretched phrase "in the case of ". Pinning may be partly prevented by use of chalk, oil, or turpentine. The latter [last] is beat. "Partly prevented" is a poor phrase. 'Prevented' is a word that does not lend itself readily to modification. He means ' checked ' or 'corrected '. These steps are necessary to produce the gas, crude oil, and ammonia, the latter [last] of which is in solution in the water obtained along with the oil.

Jan 1, 1931

By M. Maccagni, J. Nielsen

"The recovery of lead from battery paste has been investigated for a long time and with the use of many different electrolytes. A number of processes have been presented, but none of them reached even the demonstration step. Engitec has developed a new concept for the battery paste electrowinning using a chloride electrolyte fed through a very innovative flow cell. The process has passed the lab and the demo scale and it is ready to be introduced on the market. In this paper, a description of the process will be provided.INTRODUCTIONThe need for improved energy storage systems as well as the introduction of commercially viable electric vehicles is providing a strong compulsion toward the research of new batteries. The lead battery is playing an important role because it is inexpensive, reliable and it is the most recycled material. This last aspect marks the lead acid battery as quite peculiar making it both the primary lead based product and the main raw material for lead production.In the last years the legislative pressure has become very strong and has forced the lead production to react through the introduction of important process innovations and market changes. The dispersive products, such as additives for paints and for fuel as well as bullets, have been practically banned all over the world while the battery market continues to grow. The lead acid battery remains the cheapest and most integrated energy storage system available and is improving to meet the new technical challenges. This is testified by the news coming from the development of new and more efficient lead acid batteries which are confirming their leading position.Unfortunately, the image of lead is very negative in the public opinion and some important actions are required to try changing this sentiment. Among them, better information to the market and users and the introduction of new and cleaner technologies in the production of lead can help."

Jan 1, 2016

By B. H. Caudle, A. D. PUCKETT

This paper summarizes precent knowledge of the ignition qualities of pure hydrocarbons likely to be present in modern Diesel engine fuels, as shown by an extensive search of the technical literature. The report also discusses the possible significance of cetane number and hydrocarbon struc- ture. Cetane or cetene numbers, and other physical properties, are tabu- lated for about 100 hydrocarbons, and a bibliography is appended. In recent years the Diesel engine has enjoyed increasing popularity due to its dependability, inherent characteristics of fuel economy, and the fact that it operates on a fuel that hitherto has been available in comparatively large quantities at a low price. These qualities have en- abled the compression-ignition engine to compete very favorably with other types of prime movers in many fields and have led to predictions of fur- ther rapid expansion in the application of Diesel power. In a survey of the field of all petroleum fuels for combustion engines, Holaday et al (9) have predicted that by 1948 railroads will be using 10 times as much Diesel fuel as was used in 1939 and that over-all consumption will have doubled that of 1939. Other estimates of the yearly demand for Diesel fuels five years hence vary from 2,6 to 5 times the amount used in 1944. Into this picture has come the question of whether the greatly in- creased production to meet this estimated demand is compatible with the maintenance and possible improvement in quality of fuels necessary to satisfy future engines. Unfortunately perhaps for the Diesel engine, factors other than those of simple arithmetical multiplication must be considered. For example, the consumption of oil in central heating plants doubled from 1935 to 1943, and a further increase of 57 percent of the 1943 demand is expected by 1950. Jet propulsion has been developed to the stage where it is entirely practical for military aircraft. Catalytic cracking plants, many of which were constructed to meet the war- time accelerated demand for high-octane gasoline, are taking their place in the refining industry. All these developments, as well as the Diesel engine, require material of approximately the same boiling range. Virgin gas oils make excellent burner fuels, perform most satisfactorily in the gas-turbine units for aircraft according to present information, and are at a premium as catalytic cracking stock.

Jul 1, 1948

By D. T. White

"Metallurgical extraction processes often call for the heating of aqueous slurries. Indirect heat exchangers are generally not feasible for service with high yield stress slurries because of low heat transfer rates. It is more appropriate to heat the slurry by direct contact, typically with steam as the heating medium. Although having a long and successful history, direct-contact heat transfer to aqueous slurries has been used without the support of pilot plant research. This paper provides results of the needed research, the work being done at a scale large enough to enable direct scale up to commercial operations. A pilot plant heater was constructed and tested to develop an understanding of the slurry heating process and to ensure that commercial scale heaters were appropriately sized.INTRODUCTIONPressure Leaching OperationsPressure leaching operations are often used to oxidise sulphide gold ores, or for extraction of nickel and cobalt from laterite ores with sulphuric acid. Where there is sufficient sulphur available, the exothermic pressure oxidation reactions can be self sustaining at temperatures as high as 225 ºC, without having to preheat the feed slurry. At lower sulphur levels, slurry preheating is required. This is typically achieved by utilising the flash steam released from the slurry letdown stages and contacting this directly with cold incoming slurry ahead of the autoclave. The vessels where this slurry-steam contact is made are known as heaters or condensers, with the number of pre-heat stages varying, depending on how much heat is evolved in the oxidation reaction (Mason, 1990).In nickel laterite pressure acid leaching processes, which operate between 245 and 270 ºC, the only significant exothermic reactions are those associated with dilution of sulphuric acid in the leach. As a consequence, slurry preheating with flash steam is always used commercially. In practice the number of flash steam preheating stages required varies from 1 to 3, driven by a number of factors, including other uses for flash steam and the upper temperature limit at which preheated slurry can be pumped. A diagram of a typical pressure acid leach train is shown in Figure 1.For pressure acid leaching operations and at low sulphur levels in pressure oxidation, boiler generated direct steam addition to the autoclave is required to sustain the reaction temperature. For this reason it is imperative that the flash steam – slurry heat transfer is efficient and the slurry temperature approaches that of the flash steam closely."

Jan 1, 2012

By McLean E. J

Background The resources of the Gippsland Basin include not only the coal and oil for which it is well known, but also the tourism resource and the quality of life which it offers its residents and visitors. To manage this group of resources requires an understanding and ability to predict the consequences of possible developments. The water of the streams and estuaries as a key component as it is both a resource and the means for transporting wastes from one area to another. To aid in the resource planning process there is a need for models of the estuarine hydraulic processes. This paper describes an appropriate modelling technique. Resource use conflicts may arise from developments in the catchment upstream of the estuarine reach. For example the diversion of water for domestic and industrial use will change the velocity and salinity structure of the downstream estuary. In turn these changes will affect sediment distribution and deposition patterns and may impose stress on the biological communities and ultimately on the fisheries resources and water quality. The manager of an estuarine system may have expertise in ecology, hydraulics or another of the specialist disciplines involved, but commonly will not. The manager will identify needs for resource and development and the broad options required to satisfy them. The manager will use these studies as the basis for his/her selection of the option for execution. Thus a model for'use by the manager of an estuarine system must have the following properties: (i) The model must be sufficiently accurate to throw up all the likely options. (ii) The model must be capable of being run by the manager, interactively, to answer `what if' questions. This requirement implies a simple code andhardware limited to a personal computer or possibly a desk top work station. (iii) The model must be robust so that unrealistic input oes not generate apparently useful output, and no output is generated for cases where the model is not designed to give results. (iv) The model must be capable of being used as part of a modelling system comprising models of all the geographic and demographic components

Jan 1, 1992

By Mauritz Kotze, Jason Furtney, Ewan Sellers, Sandy Etchells, Tom Szendrei

The development of a simple model for gas flow and burden movement has driven the need to improve our understanding of burden breakage mechanisms for single hole blasts and the interaction between multiple holes in solid and jointed rock masses. Conventional analytical understandings of the burden breakout using the elastic-tensile fracture model were studied and found to provide a breakout angle that is independent of burden in contradiction to experimental data. By considering rock fracture in terms of Mohr-Coulomb plasticity using analytical expressions from the field of cavity expansion analysis an improved relationship between breakout angle and burden is derived until the point of critical breakout at which the angle of breakout suddenly changes from between 90 degree and 100 degrees to zero. This suggests that the critical burden occurs at about 0.6 times the radial fracture zone calculated from the analytical solutions.

Jan 1, 2013

By K. L. Bainbridge

This report describes the results of a study to determine which types of, and to what extent, mining wastes can contaminate groundwater through leaching of acid-forming or potentially toxic constituents. The primary focus of this study was on coal mining wastes, especially overburden spoils and preparation plant refuse. In addition, the potential for contamination by leachates from clean coal stockpiles was also examined. The study approach included investigation of (a) the amounts and geographic locations of mining wastes in the United States; (b) the chemical character of mining wastes, especially with regard to potentially acid-firming or toxic constituents; and (c) the extent to which acid and/or toxic components are leached from mining wastes by rainwater. To evaluate the leachability of coal wastes, a laboratory waste leaching method was developed during this study to specifically simulate the leaching process over a long-term. Waste samples collected during this study were also leached by the EPA extraction procedure and ASTM waste leaching method. Results of the three leach test methods were compared to evaluate their relative capabilities to predict the leachability of mining wastes.

Jan 1, 1980

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010