Search Documents

By C. R. McCann

The Bureau of Mines conducted an experimental study of conditions needed to produce flames of pulverized coal when the heat needed for ignition is sup-plied only from the flame and hot furnace refractory. An electrically heated furnace which burned about 1 pound of coal per hour was designed and fabricated. A sheath of air, surrounding the primary coal and air stream, was used to prevent entry of hot gases from recirculating combustion products. Furnace temperatures needed for ignition ranged from about 1,8300 F for an Illinois coal to 2,250° F for a Beckley seam coal. Apparent flame velocities were about 2 to 5 feet per second, increasing with volatile content of the coal and with distance from the burner mouth to the flame. The time required for ignition, approximately 0.02 to 0.07 sec, was a better measure of flame behavior than was velocity.

Jan 1, 1969

By M. Brozek

The constant of flotation velocity is the value characterizing the kinetics of cyclic flotation. In the statistical theory of flotation its value is the function of probabilities of collision, adhesion and tearing off the grain from the air bubble. The grain ? air bubble collision plays a key role since there must be a prior collision before the grain ? air bubble adhesion happens. The probability of such an event to occur is proportional to the relation of the grain diameter to the bubble diameter. When the grain sizes are given, it is possible to control the value of collision probability by means of the size of air bubbles. Consequently, it is significant to find the effect of physical and physicochemical factors upon the diameter of air bubbles in the form of a mathematical dependence. In the pneumo-mechanical flotation machine the air bubbles are generated by the blades of the rotor. The dispergation rate is affected by, among others, the rotor rotational speed, the amount of air transported to the flotation chamber an time and the liquid surface tension, depending on the type and number of applied flotation reagents. In the proposed paper the authors will present the distribution of air bubble diameters on the grounds of the above factors, according to the laws of thermodynamics. The correctness of the de-rived dependences will be verified empirically.

Jan 1, 2014

By R. A. Roberti

Most copper refineries use conventional wheel systems to cast anodes. over a period of time the copper moulds that are used become warped and cracks develop. To control mould warpage, the mould's are either rejected after a certain warpage is reached, or the shape is restored by mechanical means. The cracks, unless they are very severe, are repaired by a peening process. Even with regular maintenance to control warpage and cracks, the moulds have a limited useful life. If warpage and cracks are not controlled, anode quality deteriorates and tankhouse operations are seriously affected. -An intensive study was initiated to develop means of controlling mould warpage which culminated in the d?evelopment of technology to control mould warpage to within ±1. 5 mm, and at the same time effectively contr0l: cracking and significantly increase the mould life-. The warpage control has been achieved by using a unique mould design. Mould cavities are present on both sides of the mould and periodic inverting controls the wa-rpage in the cavities. The mould casting procedure has been developed and all production wheels have been converted to the new mould design. The performance characteristics of these moulds will be detailed. 21

Jan 1, 1987

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By Ray H. Hario

Background of Erie Mining Company Erie Mining Company, managed by Pickands Mather & Co., is one of the largest producers of iron ore pellets in the United States. The plant is located at Hoyt Lakes, Minnesota, sixty-five miles north of Duluth on the eastern end of the Mesabi Range. Taconite Harbor, situated on the north shore of Lake Superior, is the location of its Power Plant and shipping facilities. (Figure 1) Even though the plant commenced operation in September, 1957, its true be-ginning can be traced back to 1931 when Pickands Mather, in conjunction with Bethlehem Steel Corporation and Youngstown Sheet and Tube Company, began investi-gating the possibilities of processing low grade ores. In 1940, Erie Mining , Company was formed. During the early and middle 1940's, laboratory and pilot plant research was proven to a point where a preliminary plant was deemed feasible and built in 1948. This plant had an annual capacity of 203,200 t (200,000 long tons) per year and, until mid-1952, was the only taconite plant in existence using commercial-size equipment. During this period, ownership of Erie Mining Company was expanded to include Interlake, Inc. and The Steel Company of Canada, Limited. In 1953, authorization was obtained from the owners to build a 7.62 M t (7.5 M long tons) per year plant at a cost in excess of $300,000,000.

Jan 1, 1977

By Adams F. C, Ridley K. L

Economic conditions after WorId War II made the recovery of Australian sources of sulphur one of considerable national importance. From 1947 to 1949 an investigation was made of recirculation techniques to produce acid plant grade gas from the Dwight-Lloyd down-draught sintering plant.During 1949 it appeared feasible to produce a gas of suitable 802 concentration and a decision was made to construct a gas purification train and a 150 tons/day contact acid plant. However, a number of difficulties remained in the production of the gases for sulphuric acid manufacture and as a result of research conducted to overcome these troubles the continuous up-draught sintering process was developed.The principal difficulties were:(a:) The down-draught sintering practice, as developed, produced an unusually high metallic lead precipitation in the windboxes. The disposal of this lead interrupted sintering operations and the delivery of gas to the acid plant.(b) The production capacity of the existing sintering plant was fully extended and the adoption of recirculation of gases, in an endeavour to satisfy acid plant requirements, would probably reduce the plant production capacity.(c) The prevailing high temperature of water available for purification train cooling required a higher than...

Jan 1, 1956

By Martin Fischer

A new method for the quantitative image analysis of complex microstructures in steel is presented. Microstructures in modern steel grades on the one hand become more and more complex while on the other hand the size of the constituents is scaled down ever further. For these reasons it is increasingly difficult or even impossible to access reliable quantitative information on ratios, shapes and spatial distributions of individual phases and constituents by utilising traditional metallographic analysis methods. The presented new analysis approach is object-based. Its basic processing units are so-called ?image objects? which reflect the pictured structures by merged groups of likely related pixels. By the use of image objects, information on shape, graphical texture and spatial distribution of the microstructural constituents can be processed. With these additional data available, it is possible to quantitatively analyse complex microstructures. This is demonstrated by the application of the method to SEM images of different multiphase steel grades. Because the analysis routine is fully automated, the analysis of large amounts of image data is possible and thereby the investigation of statistically relevant areas of microstructures.

Jan 1, 2009

By Mark E. Smith

Oxide ores can consume enormous amounts of expensive sulfuric acid. The problem is amplified with increasing heap heights. One solution is to provide a thin liner and drainage system between each lift of ore, thereby intercepting the pregnant leach leach solution (PLS) after it exits the active lift. However, these liner systems require special attention to hydraulics, slope stability and geomembrane design criteria. Inadequate attention to the first two can result in reduced recoveries, increased acid consumption andsystem failures. The geomembrane selection criteria are different from the base liner, and optimizing its selection can have significant effects on the operation’s bottom line.

Jan 1, 1996

By Dale S. Preece

A Discrete element computer program named DMC @istinct Motion Code) has been developed for modeling rock blasting. This program employs explicit time integration and uses spherical or cylindrical elements which are represented as circles in 2-D. DMC calculations have been compared with measurements on bench blasts in the field with relatively good comparison. Structural rock mass characteristics have a significant impact on any blast and DMC has not, until now, included these effects. This paper discusses a recently added DMC capability for treating joints and bedding planes in bench blast simulations.

Jan 1, 1995

To generate a most profitable ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1990

By Oren C. Baptist, Carlon S. Land, Eliot J. White

The water sensitivity of the oil - gas - producing sandstones in three fields in the Patrick Draw area of southwestern Wyoming was estimated by laboratory testing . The tests used to estimate sensitivity , which is a measure of the loss of well productivity if the producing formation is invaded by fresh water , are : Porosity ; permeability to gas , water , and brines ; saturation characteristics with air displacing water from the samples and by mercury injection ; and identification of clay minerals by X - ray diffraction . Laboratory results indicate that the degree of water sensitivity of the sands in the Patrick Draw, Table Rock , and Desert Springs fields vary , in that order , from moderately sensitive to highly sensitive . The main cause of the sensitivity appears to be the movement of fine particles in the pores , but the swelling of a small amount of an expandible clay mineral may also contribute to the permeability reduction observed in the samples . Laboratory results further indicate that the permeability of the sands to fresh water is seriously reduced if they are first flushed with sodium chloride brine ; calcium chloride brine is less harmful to the sands than sodium chloride brine . The low original permeability of the oil sand in the Patrick Draw field , together with its moderate sensitivity , indicate that the rate of water injection for the secondary recovery of oil will be low . Limited field experience in two pilot - injection wells confirms this prediction .

Jan 1, 1964

By R. T. Jones

Slags have been produced as by-products from pyrometallurgical processes for thousands of years, and have generally been regarded as waste. Many of these slags are no longer seen as residues merely to be discarded, but as potential economic sources of metals, or as useful by-products in their own right. Slag cleaning can enhance the recovery of valuable metals in existing pyrometallurgical processes, or can produce economic value from recycling old slag dumps. For example, a process has been developed and implemented industrially for recovering cobalt from copper smelting slag in a DC arc furnace. The relatively non-leachable behaviour of glassy slags allows them to be used as a very safe means of disposal of metallurgical waste streams, including many that are classified as hazardous. The high temperatures, reducing conditions, and good mixing that can be achieved in a DC arc furnace enable the effective functioning of this environmentally beneficial means of disposal. Lead blast furnace slag can be rendered safe for disposal by treating it using the Enviroplas process, which strips most of the hazardous lead from the slag (and traps the rest in an insoluble glassy slag) and recovers economic quantities of zinc by absorbing (in a lead splash condenser)the zinc vapour that is fumed off in the furnace. Another example can be seen in the recovery of a chromium- and nickel-containing alloy from stainless steel plant dust, while producing a disposable residual slag. The examples presented here illustrate that it is possible to develop processes that are both economic and environmentally beneficial. Keywords: DC arc furnace, plasma, slag cleaning, cobalt recovery, zinc fuming, Enviroplas, jigging, re-melting fines, environmental, economic

Jan 1, 2004

By W. B. Morrey

This paper deals with the development of the new cap-sensitive slurry explosives. The history and special features of these explosives are outlined, and recent field trials are described.

Jan 1, 1973

By Philip C. Good

Preliminary studies showed that direct hydrolysis of H2SiF6 to SiO2 and HF at elevated temperatures was subject to many mechanical difficulties, and that corrosion of construction materials was a serious problem. Elimination of SiO2 from the HF product was generally poor. An alternative procedure, hydrolysis of lime-neutralized H2SiF6 by steam at 950° to 1,100° C, yielded a product very low in SiO2. Condensates containing up to 300 g/1 HF were prepared.

Jan 1, 1968

By Martin Landwehr

"Dust samplers are based on different principles. The konimeter is based on the number of particles counted; mining applications are based on routine sampling; and the photometrical evaluation of samples is used after the pre-separation of particles above 5 micron by the mining konimeter. In special cases, the Draeger sampler is used for quantitative analysis. General trends are toward larger samples, concentration on a weight basis, fractionation into size groups by different techniques and an analysis of composition. Standards or TLVs already exist in all industries. Surface industries base their criteria on concentrations and quartz contents in particles below 5 micron. The mining industry uses the tyndalloscope routinely to determine concentrations; concurrent] y, the rock content, as deter-mined by ashing samples, is obtained by konimeter.Threshold limits are related to the rock content in respirable fractions and tyndallometrically determined concentrations. The TL Vs are based empirically on Landwehr's ""dust values,"" as agreed upon with the Mines Inspectorates. Recently, and in accurate sampling, dust samplers have been used that count the dust in two fractions -above and below 5 microns. Mineral composition is determined either for all minerais or just for quartz. In assessing the dust hazard by Landwehr's ""dust values,"" all minerais are taken into consideration; in coal dust sampling, however, only the quartz content is taken into account. Efforts are now being made to co-ordinate the different assessment methods, arriving at uniform MAC values in agreement with those of other countries."

Jan 1, 1969

By CIM Standing Committee

The CIM Definition Standards on Mineral Resources and Reserves (CIM Definition Standards) establish definitions and guidance on the definitions for Mineral Resources, Mineral Reserves, and mining studies used in Canada. The Mineral Resource, Mineral Reserve, and mining study definitions are incorporated, by reference, into National Instrument 43-101 – Standards of Disclosure for Mineral Projects (NI 43-101). The CIM Definition Standards can be viewed at mrmr.cim.org. Readers should be aware that reports written by persons issuing technical reports that disclose information about exploration or other mining properties to the public in Canada are governed by a number of securities regulations.

May 10, 2014

Laboratory electrical resistivity measurements of rocks are reviewed. Inductive and galvanic methods are discussed together with the ten important experimental factors which should be considered in an investigation.These experimental factors are electrodes, sample preparation, measurement errors, temporal current variations, current density, frequency, electrolyte composition, electrolyte saturation, pressure, and temperature.

Jan 1, 1969

By F. -Z. Ji, A. G. Irons, M. Barati, K. Coley

In order to optimize carbon injection into oxidizing slags, in terms of carbon and iron yield, we must have a detailed understanding of the kinetics of the reactions involved. The current study measures the rate of carbon oxidation during injection at steelmaking temperature by means of injections of coal into EAF slags. The compositions of analysed outgoing gas were used to calculate gas flow rate and hence the gasification rate of carbon. A fundamental equation to predict residual carbon in slags was developed. The predictions using this model at moderate injection rates are in good agreement with experimental data. The reaction rate of EAF slag with carbon is under mixed control by the slag gas and the gas carbon reactions. The relative importance of each step depends mainly on the v-ratio of slags. A relative reactivity parameter ? has been defined and it is found to be important to carbon-slag reaction kinetics and slag foaming. Key words: carbon-slag reaction, kinetics, slag foaming.

Jan 1, 2004

By K J. Ward, C N. Hatton, J Scalia IV, C A. Bareither, D L. Spencer

The mining industry is experiencing change in the governance of tailings facilities (TFs). Guidance and regulations across many jurisdictions contribute to this amorphous change. The Canadian Dam Association, Mining Association of Canada, Australian National Committee on Large Dams, and the Global Industry Standard on Tailings Management, produced by the International Council on Mining and Metals, are establishing guidelines for more rigorous industry governance. Evolving guidance regarding TFs is developing concurrently with a shortage of experienced tailings engineers, which adversely affects the resource base available to support new governance. This paper presents an updated semi-quantitative estimate of the impending resource shortage of qualified tailings professionals. Updates are provided herein for the estimated number of TFs worldwide, which included available data on active and inactive TFs, as well as the estimated labor resources required to service these facilities. The tailings labor shortage is discussed in the context of academic and professional training currently available to increase the quantity of trained personnel. This paper represents a discrete moment in time as contributions to the available information and inventories accessed continue to improve, but as of today are incomplete. However, the data and information included provide insight into the resource deficiencies currently within our profession, training and education opportunities to address those resource deficiencies, and a snapshot of a recent professional training course offered on mine tailings.

Jul 1, 2021

By Richard H. Olson

The following discussion will deal with the domestic talc industry only, inasmuch as the writer has had no experience in this field outside of the U. S. This is strictly a geological-mining approach; no attempt is made to assess in depth the effects which milling technology and marketing capability might have in determining the potential of any given talc deposit.

Jan 1, 1970