Search Documents

By R. H. Swallow, George Hess

Aerial photography was once a crude, uncertain tool. Today it is a precision mapping instrument which saves important time and money for strip mining and other industry. Aerial photography began in the boxkite days of aviation. The Army first used it for rough reconnaissance photographs. Then, in the early Twenties, industry began to use aerial photographs of their plants and facilities for advertising or annual reports. The quality of these pictures was not very good by today's standards, but this work began the development of better cameras, better lenses, better photographic techniques.

Jan 1, 1949

By R. S. Olsen

The Bureau of Mines is engaged in research to recover aluminum from kaolinitic clay and other nonbauxitic domestic resources. As part of this work, calcined Georgia kaolin was prepared by a process that prevents slime formation and makes the leached residues fast settling and easy to filter. The leaching reaction for calcined kaolinitic clay in a 5 pct stoichiometric excess of boiling 23-to 26-pct HCI was found to be zero order. Rate constants based on the weight-fraction of aluminum in the clay were found to be between 0.095 and 0.15 min-1 depending on feed preparation and leaching parameters. The mathematical relationships between aluminum extraction and time for both batch and continuous, stirred-tank operations were derived and verified experimentally.

Jan 1, 1983

By F. R. Zachar

IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider 'seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1952

By David E. Siskind

The Bureau of Mines has studied the fracturing and associated damage occurring in the vicinity of blastholes from five shots fired in the shale pillars in the White Pine copper mine, White Pine, Mich. Four types of explosives (AN-FO, commercial extra dynamite, ammonia gelatin dynamite, and a low-density, low-velocity permissible) were used. Cores were taken from the blast region and examined by ultrasonic and petrographic techniques. Pulse wave velocities were measured across the core diameters, and thin sections showing cracks and changes in lithology were examined in an attempt to establish zones of damage. Cores from the blast regions and areas near pillar free faces were found to have abnormally low pulse velocities. Petrographic study of the thin sections showed that the negative velocity anomalies were caused by cracks in the cores. Crushing and extensive fracturing prevented meaningful measurements on core fragments from the immediate blast vicinities. Compositional, changes and other rock nonuniformities, such as joints and preexisting fractures, tended to mask detailed damage differences among the four explosives; however, the two most energetic explosives (extra dynamite and ammonia gelatin dynamite) produced damage zones two to three times as large as the AN-FO and low-velocity permissible explosives.

Jan 1, 1973

In February 2001, Kalgoorlie Consolidated Gold Mines (KCGM) commissioned its first full-scale ultra fine grinding (UFG) plant to supplement existing roaster concentrate treatment capacity. This process involves the fine grinding of refractory pyritic concentrate to 10µm, followed by direct cyanide leaching for the recovery of gold. By this means gold is economically extracted from the concentrate without the need to first oxidise the host pyrite. This paper details the history of the project from initial laboratory testwork comparing possible treatment options, to current performance of the 12 tph plant. This includes the cost comparison of the major treatment options, the laboratory and pilot scale UFG performance, the UFG mill selection, cyanide leaching of UFG product, commissioning and plant performance to date.

Jan 1, 2002

By Davenport, Edmund S.

THE specific aim of this work has been to study certain forms of internal deterioration which occur in tungsten filaments when subjected to high temperatures under various conditions, and to determine the cause of such deterioration. This would naturally lead to a consideration of methods of control or means of prevention of the phenomena. The deterioration was first noticed as a peculiar condition in the grain boundaries of certain tungsten filaments which had been burned t for long periods in lamps. In these cases it was noted that the grain bound aries contained a number of minute black dots which were at first thought to be non-metallic inclusions. It was demonstrated later that these dots or pits, as they were designated, could be readily produced by burning filaments in an atmosphere of flowing hydrogen. This method was convenient and adequate for the purpose, and was adopted for most of the work discussed in this paper. The evidence accumulated to date indicates that these pits arc actually small voids between the grains. The purpose of this paper is to, present the information on this interesting subject gathered during a period of about 3 years. As applied to tungsten, the subject appears to be of considerable importance, experience having shown that this pitting is frequently associated with poor performance of filaments in lamps.

Jan 1, 1927

At the Kidd Creek mine operated by Ecstall Mining, Ltd. near Timmins, Ontario, Honeywell has installed a sophisticated new quick- thinking computer system that keeps tabs on conditions along three separate processing streams at once and relays continuous 60-second data to the mill operator. Believed to be the first of its kind, the system picks up data from two independent x-ray spectrometers simultaneously. A digital computer from Honeywell's Computer Control Division receives and interprets real-time information gathered by online x-ray analyzers, and the system then advises control room operators of the relative amount of each of five elements at five points in each of the three process streams. The system is reported to provide a quantitative analysis of the five elements at a given point in the process within one minute-which is about 120 times as fast as a chemical laboratory assay could be performed. With this instant data at his command, the mill operator can make timely process adjustments to correct any deviation from optimum flotation results, thus salvaging valuable minerals that would inevitably be lost with slower detection methods. The minerals recovered at Kidd creek are copper, lead, iron, silver and zinc.

Jan 8, 1968

By H. E. Heide

"Before the war, the United States was the world’s leading consumer of tin, the industrial applications of which had become widespread. Domestic production was negligible, and requirements were met almost entirely by imports, principally from British Malaya, United Kingdom and China. Average annual imports for the years 1925-1929 amounted to 78,009 long tons.With the advent of war in Europe and signing of the Japanese-German pact, it was realized that foreign sources of supplies were threatened, and steps were taken by Congress to forestall critical shortages of tin and other minerals. These steps in regard to tin included stock-piling, improving reclamation and conservation, increasing South American production, constructing a smelter in the United States for treatment of tin, ores, and intensifying the search for domestic tin deposits. Annual imports were raised to 140,873 long tons by 1941. On 1945, annual imports had shrunk to 37,675 long tons and consumption had been reduced to 52,100 tons of primary and secondary tin but not tin content of scrap alloy.The Strategic Minerals Act, passed by the Congress in 1939, authorized the investigation of domestic tin deposits.As Alaska had supplied virtually all of the domestic output of tin, an investigation of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.The Lost River lode tin mine on the Seward Peninsula was examined by H. E. Heide of the Bureau of Mines in 1942. Possibilities for developing a significant amount of tin appeared favorable, and exploration of the ore bodies was started in August 1942."

Jul 1, 1946

By Jerry J. Ran

In open stope mining borehole deviation is one of the main factors affecting the blasting results. Though previous research has identified some actual deviation patterns, these studies are unable to relate the hole deviation pattern with the blasting results and therefore it is not possible to modify the design or take remedial measures based on the prediction of the blasting results. An alternative to the conventional method for borehole surveying is the in-hole probing techniques. With their inherent errors, it is important to evaluate these surveying systems under conditions of different mine sites. The lack of available assessment methods has limited the application of these techniques. In this paper some of the characteristics of the actual hole deviation pattern are discussed based on data from surveying production holes in six stopes. A method of predicting the blasting results is proposed by considering the borehole deviation pattern. Based on the prediction stope design can be modified or further surveying is carried out to improve the blasting results. The tolerable error is introduced to relate the surveying error with the drilling pattern and therefore it is possible to assess various in-hole-surveying techniques.

May 1, 2002

By K. S. Gritton

The U.S. Bureau of Mines has investigated methods for extracting metals from a variety of arsenic-containing smelter flue dusts. One proposed flowsheet includes a sulfuric acid leach, a cooling step to precipitate hydrated copper sulfate, and a reduction-precipitation of As2O3. Arsenic extractions greater than 90 pct were achieved, while copper extraction ranged from 50 to 85 pct under the conditions examined. Copper was removed from the leach solutions by crystallization followed by SO2 precipitation of arsenic which resulted in a 98 to 99.9 pct As2O3 product. Other metals, such as lead and zinc, were concentrated in the leach residue or in other byproduct streams for recovery of their valuable metal contents.

Jan 1, 1990

These inspection standards have been prepared for use in the Federal inspection of bituminous and lignite mines. They are a revision of "Tentative Coal-Mine Inspection Standards," published as Bureau of Mines Information Circular 7204 in February 1942 and employed a guide for Federal inspections. Numerous changes have been made in the original standards owing in part to recognition of shortages of some types of safety equipment due to the war, in part because of need of additional standards to cover certain mine conditions' arid' practices, and in part to conditions not foreseen when the original standards were prepared. About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however; failure to carry out the suggestions made in such of the other standards as are applicable may also' lead' to the loss of lives.

Jan 1, 1943

By J. A. Taylor, H. F. Yancey

"INTRODUCTION Froth flotation as applied to coal is a process for separating desirable carbonaceous material from undesirable inorganic matter. In general, the feed must be finer than one eighth inch in size. The principal use of the process in the preparation of coal appears to be in the treatment of the fine sizes produced by breakage during mining and preparation.The Bureau of Vines in Information Circular 6714 has published general information on coal flotation, summarized investigative studies of the process, and described operating plants throughout the world with their tonnage, reagent consumption and operating costs.4ACKNOWLEDGMENTSThe present study of means for depressing pyrite and reducing ash ty froth flotation was conducted at the Northwest Experiment Station of the United States Bureau of Wines in cooperation with the College of vines. University of Washington, under the general direction of A. C. Fieldner, chief engineer, Experiment Stations Division, Bureau of Wines. Grateful acknowledgment is made for suggestions and criticisms received from W. H. Coghill, supervising engineer, U.S. Bureau of Mines Mississippi Valley Experiment Station, Rolla, Mo.; J. B. Morrow, and R. E. Zimmerman, of the Pittsburgh Coal Co.; and Dean Milnor Roberts and Prof. Joseph Daniels, of the College of Mines, University of Washington.FLOTATION AND DEPRESSIONA substance will tend to float if its surface attracts a gas film more strongly than it does a liquid film when both air and liquid are competing for this attraction. On the other hand, a substance will not float if its surface attracts a liquid film more strongly than it does a gas film. All theories of depression depend upon this fact. A wetted particle of floatable size most likely will be found in the tailings after the flotation process has been completed.The crux of flotation is the selective wetting of the undesirable material that tends to float. Two general methods 5, 6, 7 of depression are in use: One combines a chemical substance with the surface to form a wettable compound, and the other employs some colloidal or ionic substance which the surface selectively adsorbs, thereby forming a wettable surface."

Jan 1, 1935

"7.1. Glossary of the Platinum-Group Minerals7.1.1. IntroductionA glossary of the platinum-group minerals (POM) serves as a useful introduction to a chapter on their mineralogy. Earlier glossaries (Cabri, 1972, 1976) were prepared for different purposes and composed in a different manner. As for most mineralogical textbooks, from Dana's System of Mineralogy, 3rd Edition (1850) , to Fleischer's Glossary of Mineral Species (1980), this glossary is primarily a chemical classification, arranged here in two tables. Table 7.1 groups the mineralforming compounds of the six platinum-group elements (POE) according to their essential anion(s) or according to the nonPOE element in intermetallic compounds. Table 7.2 is a similar listing for the native metals and alloys of the POE. Both tables include unidentified POM considered to be bona fide new minerals requiring additional study for complete characterization and recognition (see Chapter 9*). Some information on the chemistry of the POM is given in the sections on X-ray data (7 .2) and ore microscopy (7 .3). Because the overwhelming majority of POM have been characterized by the electron microprobe, a more detailed account of representative analyses is given in Chapter 8**. The total POM listed in Tables 7.1 and 7.2 is about 100, after deleting some which would not qualify as discrete species if found today, but which are still recognized on historical grounds; e.g. iridosmine, osmiridium, platiniridium. Tables 7.1 and 7.2 also include 28 unnamed POM; included because they are considered to be probably new species (Cabri 1981 b). The referral scheme for unnamed minerals is the same as in Chapter 9. There are considerably more palladium minerals known than other POM; the proportion of total species (listed in Tables 7.1 and 7 .2) for the POE is: Pd 48%, Pt 21 o/o , Ru and Ir 9% each, Rh 8% and Os 5%. These proportions are in marked contrast to the estimated cosmic abundance, as compiled for average type C1 chondrite by Naldrett and Duke (1980): Pt 29%, Ru 20%, Pd, Ir and Os 15% each, and Rh 6%."

Jan 1, 1979

By Pieter van Nierop

Outline ? What is gasification? ? Gasification Technologies ? Gasification ?The early years ? Gasification ? The last decade ? The Alberta Situation ? The Importance of Gasification in Alberta ? Polygeneration ? Development ? Conclusion

May 1, 2004

By B Taylor

The Perseverance deposit is the most southerly known economic copper/gold deposit within the Cobar gold field. The deposit is situated approximately 12 km to the south-southeast of Cobar and is essentially blind to surface with the top of economic mineralisation occurring 750 m below ground level.Based on the December 2010 resource estimate (inclusive of reserves and net of depletion) the deposit contains 3 011 000 tonnes at 6.1 g/t Au and 0.90 per cent Cu (590 000 oz of gold and 28 000 tonnes of copper). The deposit is comprised of four principal lenses, the Perseverance, Hulk, Zone B, and Hercules lenses. In excess of 90 per cent of the known resource tonnes are contained within the Perseverance and Hulk lenses. The deposit is shear related and hosted within lower Devonian rocks of the Cobar Basin. The competency contrast of rhyolites juxtaposed against sediments by the Peak-Perseverance shear is the principal control on mineralisation. Both the Perseverance and Hulk lenses are primarily hosted by brecciated rhyolites juxtaposed against Chesney formation sediments across the Peak-Perseverance shear. This faulted rhyolite sediment contact roughly defines the global orientation of the deposit. The Perseverance lens continues within the shear for up to several hundred metres beyond the extent of the faulted rhyolite sediment contact. Mineralisation within the shear beyond the faulted rhyolite contact zone is hosted by sheared silicified sediments. The Perseverance lens remains open at depth and to the south.The Zone B and Hercules lenses, which are significantly less important in tonnage terms, are hosted by rhyolite breccias within the main body of the rhyolite and appear to be only tenuously related to the Peak-Perseverance shear. Within the Perseverance lens, the presence of northeast trending high grade breccia veins developed oblique to the north-south trending shear system has led to the development of steeply north plunging high grade ore shoots within a globally north-south trending mineralised domain. These high grade shoots have limited horizontal continuity but significant down plunge extent.The presence of coarse gold and the resulting strongly skewed nature of the gold grades, in conjunction with controls on mineralisation which are not parallel to the mineralised domain, has led to predictive difficulties regarding stope performance.Strong heterogeneity of the gold content of the ore and geological controls on mineralisation which are not parallel to the global trend of the mineralisation impose a set of difficulties which sound geological control is helping overcome.

Aug 22, 2011

By Richard L. Ash

A question that frequently arises during litigation concerned with accidents or alleged damages involving blasting is "were the explosives used according to the best known standards"" The question is not confined to only law suits, however, but also everytime poor blasting results occur. Unfortunately, general guidelines that can be used to define what may be considered as proper practice have not been established by any responsible body upon which to base a reliable Judgment; more often than not decisions are made primarily according to personal opinion.

Jan 1, 1975

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020

By D. Harrington, W. J. Fene, H. B. Humphrey

In the fiscal years 1946 and 1947 the number of mine explosions decreased compared with the preceding years. However, the loss of life was so serious during the fiscal year 1947 the period when the Government administered bi- tuminous-coal and lignite mines that from April to June 1947 extraordinary measures were taken in mines then under Government possession to obtain com- pliance with provisions concerning rock dusting, ventilation, and blasting that had not been followed. The great loss of life in explosions during the fiscal year 1947 as compared with 1944, 1945, and 1946 is not easy to explain, but the necessity for maintaining adequate protection has been definitely demonstrated. Management, workers, and inspection agencies alike must keep the mines reasonably safe against explosions or allow them to lapse into a condition where chance is the principal protection against disaster. The at- tention given to protecting coal mines and the men employed in them against mine fires, following the disastrous fires in 1944 and 1945, has at least tem- porarily controlled this hazard loss of life from coal-mine fires was re- duced to 1 fatality in 1947. The number of fires was also less, and progress has been made in reducing the heavy losses in both life and property from un- derground coal-mine fires that occurred in the two years mentioned. Fatalities from mine explosions during the past 6 fiscal years, July 1942 to June 1947, totaled 674, and there were 149 explosions; during the preceding 6 years there were 655 fatalities in 132 explosions. The 6 fiscal years 1942- 47 cover the active period of Federal coal-mine inspection. During the fiscal year 1947, there were 154 fatalities from explosions compared with 58 during the fiscal year 1946, 64 in 1945, 94 in 1944, 152 in 1943, and 152 in 1942.

May 1, 1948

By Missy Isaman

"Mixed ground tunnels come in all kinds. In rock tunnels with possible faults and high pressure water, the challenges are many. With the advent of Crossover TBMs, contractors can minimize machine wear in such conditions while maximizing efficiency. The newest generation of Crossover is exemplified by two projects in Albania and Turkey. A 5.56 m Crossover TBM destined for Turkey’s Gerede Water Transmission will be assembled using Onsite First Time Assembly (OFTA) from within an existing tunnel. The unique machine will bore through 30 fault zones requiring the TBM to be sealable to up to 20 bar so pre-consolidation grouting can be done. If boring under pressure is required, the TBM will bore sequentially using the screw conveyor fore and aft gates. Skewing further towards hard rock, a unique 6.2 m diameter Double Shield TBM with Crossover features was designed for Albania’s Moglicë Headrace Tunnel. The machine features closure doors and a sealing system to contain inrushes of water until they can be grouted off. This paper will discuss the unique aspects of the Crossover designs, including their inception as based on past projects in difficult ground, and their utilization at the two current projects. INTRODUCTION Specialized tunnel boring machines have been made for years to tackle specific types of ground conditions. Traditional types of TBMs bore within a specific set of ground conditions. If a project is located in a competent granite face, then a Main Beam machine is a good solution. In soft ground, Earth Pressure Balance (EPB) machines are the method of choice. Years of experience and engineering advancements have made both types of machines fast and economical solutions for tunneling. Unfortunately not all ground conditions are a perfect swath of one material, and the need for a more diverse machine is apparent."

Jan 1, 2016

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1936