Search Documents

A numerical method for discriminating between replacement and sedimentary processes is applied to a folded stratiform sulphide occurrence. It is shown that numerical treatment of chemical analyses from a single diamond drill hole allowed a rapid assignment of the ore to the syngenetic sedimentary class and thereby enabled a revision of the evaluation program concerned with consequent reduction in costs.

Jan 1, 1973

By Thomas Marcher

Stanford Linear Accelerator Center (SLAC) is located in Menlo Park, CA. In order to allow for enhanced experiments, the current facilities required expansion. Tunnels were excavated through very weak sedimentary rock interspersed with uncemented zones (Ladera Sandstone) employing the principles of the NATM. The overburden var-ied from 10 to 80 feet. The paper addresses the characterization of Ladera Sandstone that can exhibit the properties of dense sand and weak rock. The paper focuses on the challenges that were encountered during the NATM initial support design and the construction phase including the geotechnical instrumentation, monitoring and design verification process in particular the excavation of the junction between access tunnel and the FEH cavern (49 ft wide by 32 ft high).

By K. C. Naidoo

There are two main types of densifying cyclones currently available in the market, namely polyeurethane (PU) and ceramic. The PU densifying cyclones are currently used throughout the Grootegeluk complex and coal beneficiation in general. It has been identified that PU densifiers wear relatively fast depending on the operating pressure and need to be replaced frequently as a result. The motivation for this paper is to achieve an increase in the densifying cyclone lifetime through less wear and an increase in efficiency resulting in the ability to build higher relative densities (RD) more quickly. This will allow for a reduction in downtimes due to replacing densifying cyclones as well as building RD and a reduction in the operating costs associated with replacing worn densifying cyclones. Some of the major findings of the study indicated that the ceramic cyclone theoretically undergoes less wear than the PU cyclone, but since wear is application-specific and was evaluated, the wear on the polyurethane cyclone was found to be minimal. The RD differential is higher on the PU cyclones than the ceramic cyclones, showing that the PU cyclones perform better in a densifying application. This is the first test conducted on this application and type of cyclones. It should therefore be noted that having the PU cyclone significantly outperform the ceramic cyclone was not expected, due to the only change being the material of construction. This is an indication to take the material of construction into account when selecting cyclones as it can have a significant impact on the cyclone performance in specific applications. Keywords: Ceramic, cyclone, densifying, density, dense medium, polyurethane, wear

Jan 1, 2020

By J K. Claflin, S R. La Brooy

A case study from a current Ausenco project is presented to demonstrate the importance of maintaining high carbon activity to illustrate the driving force for plant improvements such as a carbon regeneration kiln upgrade.This paper revisits the factors that influence carbon activity for gold loading, with emphasis on deactivation by organic solution components such as flotation reagents.Kiln process design requirements for effective thermal regeneration are reviewed including the interaction of parameters such as temperature, kiln atmosphere and residence time.The different types of kilns that have been used for carbon reactivation are described. A check list is provided of what to look for when purchasing a carbon reactivation system for dealing with severely fouled carbon. This covers the ancillary equipment as well as the kiln itself.While the effectiveness of the carbon reactivation kiln is vital to maintenance of high carbon activity it needs to be remembered that this is only the end of pipe solution. It is also important to ensure that reagents such as frothers and flotation collectors are appropriately chosen to maximise recovery and at the same time minimise carbon deactivation.CITATION:La Brooy, S R and Claflin, J K, 2013. Carbon management in a high gold price environment, in Proceedings MetPlant 2013 , pp 455-467 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Jai-Woon Moon, Wonnyon Kim

Deep-sea hydrothermal vents (hereafter chimneys) are commonly found on the new crust forming along divergent plate boundaries. Related to the chimney cycle from birth to death, it is hard to define the growth stage of the chimney due to a brief life span of the venting hydrothermal plume. Here we try to categorize the mineral magnetic properties of the chimneys according to their venting fluid-temperatures. Hydrothermal sulfide deposits in the Southwest Pacific were explored in 2012 and chimneys were collected using remotely operated vehicle (ROV) and Grab with AV camera (GTV). In the present study, mineral magnetic properties of three Cu-rich chimneys were measured: a high-temperature chimney showing a venting fluid-temperature of about 200°C (ROV01); a lowtemperature chimney of about 80°C (GTV01); and an inactive chimney (ROV02). The chimneys were sliced to ~1 cm intervals from core to outer margin. Magnetic properties of ROV01 are dominated by pyrrhotite, except for the most outer part that experienced severe oxidation. Concentration and grain-size of pyrrhotite are relatively low and fine respectively. In the GTV01, pyrrhotite, dominant in the core, is gradually mixed with hematite toward the outer margin of the chimney due to secondary oxidation. Both the concentration and grain-size of the magnetic minerals are greater compared to the GTV01. High concentration and large grain-size of magnetic minerals characterize ROV02. Dominant magnetic phases are pyrrhotite, hematite, and goethite. In particular, the most outer margin shows the presence of magnetite produced possibly by magnetotactic bacterial activity. Such distinctive contrast in magnetic concentration, grain-size, and mineralogy among three different types of chimneys enables the life stage of the Cu-rich chimneys to be determined through a mineral magnetic study.

Sep 1, 2014

By E. J. Wade

My subject is gold price forecasting and monitoring as an important aspect of gold marketing. While I 'm specifically addressing gold, it is understandable that many other commodities could be readily substituted. Gold marketing must be studied as three distinct processes, and it is my intention to cover each of these processes in turn. First I?ll cover the process of gold price monitoring and forecasting in some detail. In order to select a method, or combination of methods, to be used to sell gold a determination of the future price profile is essential. The profitability of the sales effort will be determined, to a large extent, by how accurately the future price behavior of the gold market has been forecast.

Jan 1, 1985

By James V. Thompson

ENGINEERS from industrialized countries are frequently called upon to examine mining operations in primitive areas and make recommendations regarding mechanization and modernization. They often set forth with self-confidence, knowing full well that all that is needed is their experience and several shiploads of mining machinery, and at times they mentally provide the answers before the problems have been clearly stated. In primitive areas it is absolutely essential that the examining engineer spend enough time at the site to acquire a thorough understanding of what is being done now and why it is done the way it is. The objective here is to state in simple terms some of the problems that may be encountered, in- as much as solutions, if they can be found at all, will differ with each experience.

Jan 8, 1958

By L. D. Schmidt

Now that the war is over, there is a great revival in popular demand to decrease pollution of the atmosphere in our cities. Great cities, such as Pittsburgh, are starting to enforce laws against violators of smoke ordinances. The substitution of low-temperature coke for bituminous coal in household heating is a most promising field for helping to eliminate the smoke nuisance. This Information Circular is written to assist in the very worth-while effort to reduce atmospheric pollution. Herein are de- scribed recent German developments in the production of low-temperature coke. Operating and cost data are given on German commercial-scale low- temperature carbonization plants.

Feb 1, 1947

By G. R. Hopkins

The average gravity of the total crude petroleum produced in the United States during; the year 1927 was 32.2° A. P. I., or 0.864 in terms of specific gravity. A similar study, made by the U. S. Geological Survey in 1921, gave the average gravity at that time as 32.0.° To one who is accustomed to thinking of crude petroleum in terms of Oklahoma-Kansas and North Texas trades it may be surprising that the average gravity for the entire country is no higher than 32.20. The chief reason for this apparent discrepancy lies mainly in California production, which in 1927 amounted to over 25 per cent of the total, but which had an average gravity of only 24.10. A factor of less importance was Arkansas, which, though on the decline as a producing State, exerted a material effect by reason of its average gravity of 21.6°, the lowest for any State. In view of the heavy production of light crude in the Seminole area of Oklahoma during 1927, it would appear that the average gravity should have shown more than a 0.2 per cent gain over 1921. That this did not occur was due to the fact that in the interim between 1921 and 1927 important heavy oil discoveries were redo, notably the Smackover field of Arkansas.

Jan 1, 1929

By Christopher R. Harris

"Considerations are presented for developing and implementing self-hardening slurry mix designs to be utilized in barrier seepage walls. Slag-cement-cement-bentonite (SCCB) slurries are the primary focus, with some comparisons referenced to the more traditional Portland-based cement-bentonite (CB) slurries. Field and laboratory mixing methods are reviewed, including 1) single sack – single mixer method; 2) bentonite slurry mixer – cementitious addition mixer method; 3) bentonite mixer – grout mixer – CB blending mixer method. Major phenomena associated with the dynamics of barrier wall excavation, such as loss of water from the in-trench slurry and consolidation of in-trench slurry are discussed. Other topics touched upon include sand content effects, fluidizers utilized, and chemical contaminants. The role of higher bentonite to water ratio is reviewed, with demonstration of improvement of filtration properties, and an increase of water retention of the final consolidated product.IntroductionSelf-hardening slurry has been utilized to construct barrier seepage walls for many decades. This is essentially a single-step slurry excavation and backfill process whereby the trench-supporting fluid gains strength over a short period during installation and maintains or develops low hydraulic conductivity. The resulting curing slurry becomes the actual barrier wall as the resultant cement-augmented clay slurry now fulfills the dual purpose of both temporary trench stabilization and final cured-in-place product. This eliminates the requirement and expense of subsequent backfill/slurry displacement operations required in traditional barrier wall installations.Self-hardening slurries have been fabricated using a number of various clays, most commonly sodium bentonite, calcium bentonite, attapulgite, and sepiolite. Perhaps due to plentiful high quality sodium bentonite deposits found domestically, the proven excavation stabilization properties imparted from sodium bentonite slurries, sodium bentonites are typically specified for formulating self-hardening slurries in the US. Cementitious materials utilized most commonly are Portland cement and slag (ground blast furnace slag or GBFS). For the purposes of this discussion, self-hardening slurry having a cementitious of Portland will be referred to as CB. Those having cementitious material of GBFS replacing Portland (partially or wholly) will be referred to as SCCB."

Jan 1, 2016

By RICHARD MAIZE

IN this critical period of our history, the coal industry of the nation, faced with many obstacles, performed its work safely during the first ten months of 1943. Thousands of the younger mine workers were inducted into the armed forces of our country and in many instances their jobs have been filled by others without much if any experience and training. This situation alone would seem to be sufficient to interfere with the safe and orderly operation of the industry but the Government's demand for a substantial increase in coal tonnage over that produced in normal times introduced a hazard which always accompanies speed, regardless of the skill of the worker.

Jan 1, 1944

By Ma Yuxin, Niu Fusheng, Yuan Zhitao, Bai Limei, Han Yuexin

"Using batch flotation experiment, contact angle measurement, particle size analysis, and scanning electron microscope (SEM), the influence and difference of pH value on the flotation rate of talc and chalcopyrite were investigate without collector at the pH range of 3~11. The results showed that, the flotation rate of talc decrease with the increasing of flotation time, while that of chalcopyrite hardly affect by flotation time, besides, the flotation rate of chalcopyrite is much less than that of talc, so the laws of flotation rate of the two minerals are independent of pH value. The flotation test data of two minerals are simulated with first order and multi-rate flotation kinetic model respectively. The simulation results showed that flotation of talc only meet the first order kinetic model, while chalcopyrite’s meet the both. In addition, According to test results of talc and chalcopyrite by the particle size distribution, SEM photographs and the contact angle measurement, the reason why talc did not conform to the first order kinetic model is not because of particle size distribution, but of particle shape. That is to say, because of sheet structure of talc, the contact angle of layers and sections are 74°and 52°respectively. At the same time, the contact angle of layers and sections are different between the particles. So flotation rates between talc particles are difference.INTRODUCTIONPossessing superior self-induced, collector-induced and sulfur-induced floatability, chalcopyrite exhibits good floatability at a wide range of pH values and potentials. Serpentine are regarded as the most difficult selected type in various chalcopyrite ore, and the predominant reason is that it contains talc. Talc, as a nonpolar layered silicate mineral, is one kind of common associated mineral in sulfide ores (Lu, 2010). Concentrate quality and flotation process of chalcopyrite are influenced as a result from the presence of talc. It is because that talc has inherent floatability which makes it readily mixed with the floated mineral and talc is easy to slime causing the slime coating of the valuable mineral (Beattie et al., 2006). Thus in order to improve the flotation effect of chalcopyrite, methods can be introduced from two respects. One method is that fast-floating talc mineral is floated preferentially, and the other is that sulfide mineral is floated prior to talc by depressing the flotation of talc mineral (Beattie et al., 2006), nevertheless, no matter with which the flotation effect of fine-sized chalcopyrite is not positive. Therefore, in order to realize the flotation separation of talc and chalcopyrite, the difference between the inherent floatability of fine-sized chalcopyrite and talc is researched and analyzed in terms of flotation dynamics in the absence of collector and frother."

Jan 1, 2016

By Andrew J. Freyman, Graham T. Armstrong

"In September, 1968, a survey of operating mines in the Yukon and the Northwest Territories was undertaken to determine the role of Indigenes (Indian, Metis, Eskimo) on the mines, and the attitude of mine management to these employees. The operating mines in the Territories had (at that date) a total employment of 2,002 men, of which 91 (4.5 per cent) were Indigenes. Indigenes make up 45 per cent of the Territorial population (18 per cent in the Yukon and 63 percent in the Northwest Territories). The paper documents some of the problems associated with indigenous employment in mines. A study was undertaken to determine the role of Indigenes (Indians, Metis, Eskimos) in operating mines in the Yukon and in the North-west Territories. In addition to the mines north of the 60th parallel, the experience of several other Canadian mines was examined. The general picture obtained is considered to be representative of the Canadian mining industry."

Jan 1, 1969

By A. S. Bayne

WITH the great increase in the use of power-driven machinery in industry, and consequent large-scale operations, the hazards to which , workmen are exposed have become much more numerous than at the beginning of the century. This is especially noticeable in mining. In the past thirty years or so, improvements in methods of excavation and metallurgy have made possible the exploitation of deposits which would have failed to make ore in previous years. This improvement, together with the in-creased use of machinery, has facilitated the mining of tremendously greater tonnages with a marked decrease in unit cost of production. This 'speed up' in mining creates numerous problems demanding close attention of operators and necessitates careful prep;tratory planning, as well as diligent supervision of actual operations. Underground openings increase in size so fast, and all phases of mining, mucking, and transportation proceed at such a rate, that a short period of reduced vigilance on the part of operators . results in disaster, both from the standpoint of safety and economies. Happily, the challenge of increased hazards has been successfully met by a general application of the slogan 'Safety First'. Today, we have large manufacturing concerns devoted entirely to the development and production of safety equipment for the protection of workmen in various branches of industry. Machinery manufacturers, in co-operation with their mining customers, have included the best possible in foolproof devices in the manufacture of hoists, compressors, boilers, electric motors, and equipment of all kinds. Mining companies and private individuals spend thousands of dollars and devote a great deal of time to research with the single object of preventing accidents and combating miners? diseases. Governments throughout the world have written regulations into their statures for the protection of miners and operators. Staffs are appointed to enforce these laws and investigate accidents to ascertain means of preventing them for the future benefit of the industry.

Jan 1, 1938

By B. M. Eiter

The impact of fatigue is seen not only in its effect on the job performance of haul truck operators but also on the health of the operator and the productivity at the mine site. Its impact can even extend outside of the mine site to the health and well-being of the surrounding community (Fourie et al., 2010). In this paper, a case study of a small, surface mining organization is presented. The goal is to highlight the fatigue risk management system implemented at the studied mine site. Mine safety personnel who were interviewed discuss the changes made to the infrastructure of the mine, to administrative areas such as the number of shifts and the use of vacation time, as well as the implementation of new technology into haulage vehicles. This paper reviews how these changes are supported in the research literature.

By Earl T. Hayes

For several years the Northwest Electrodevelopment Laboratory of the Bureau of Mines, in cooperation with the Air Materiel Command, U. S. Air Force, has been studying zirconium alloys. A preliminary survey of these alloys has been completed and reported as a Bureau of Mines Report of Investigations. 4/ Originally the purpose was to determine the suitability of zirconium alloys in medium-temperature applications. However, data also were obtained on other properties of these alloys, and later the scope was broadened to include amore detailed investigation of a selected group. The zirconium-titanium system was one of those chosen. The Bureau of Mines has been instrumental in the commercial development of both of these metals and has constructed pilot plants for the production of titanium at Boulder City, Nev., and for zirconium at Albany, Oreg. Both elements are in subgroup A, fourth series of the periodic table, and therefore have many properties in common. Since both have similar atomic structures and lattice dimensions the possibility of extended mutual solubility seemed likely. Inc transition-point diagram of Fast indicated that the two metals are completely miscible in all proportions in both the alpha and beta forms.

Jan 1, 1951

By Unkown

To the Membership of the Institute Gentlemen: The Mineral Industry of Canada in 1948 The preliminary estimate issued by the Dominion Bureau of Statistics and tabulated in the Bulletin of January, 1949, indicated that the value of Canada's mineral production in 1948 reached an all-time high of $808,180,216, showing an increase of 25 per cent over the previous record of $644,696,007 established in the preceding year. The output value of metallics was increased by 22.4 per cent; of fuels, by 43.7 percent of other non-metallics, by 19 per 'cent; and of structural materials, by 16.8 per cent. The value of metals produced in 1948 at $483,770,759, was about $87,000,000 more than in the previous year. There were substantial increases in the tonnages of copper, lead zinc nickel, and other base metals produced, but the rises in market prices for such metals accounted for most of the gains in output values. Production of gold at 3,495,403 ounces valued at $122,339,105 indicated an increase in volume of approximately 500,000 ounces and an increase in value of 14 per cent. Despite the benefits provided under the Emergency Gold Mining Assistance Act 1948 the volume of gold produced in the year was still nearly 2,000,000 ounces less than the record of 5,300,000 ounces established in 1941. The value of mineral fuels produced in 1948, at $158,787,255, was 44 per cent above the 1947 total. Coal production at 18,431,250 tons valued at $107,298,757, while substantially higher than in the preceding year was still half a million tons below the record reached in 1942. Striking developments in the Leduc field in Alberta were responsible for bringing the output of crude petroleum in the year to a new high of 12,098,166 barrels, valued at $36,858,959.

Jan 1, 1949

By W. M. Dressel

A simple, reliable field test for beryllium in rocks has been developed by the Rolla Metallurgy Research Center of the Federal Bureau of Minas. A small portion of the pulverized rock is fused with a sodium carbonate-sodium hydroxide flux in a wire loop. The fused mass is dissolved in water, a few drops of quinizarin solution are added, and the solution is viewed under ultraviolet light. A pink-to-orange fluorescence reveals the presence of beryllium in a sample containing as little as 0.013 percent beryllium (0.26 percent beryl). INTRODUCTION New and potential uses for beryllium make necessary a more intensive search for this metal, which is so similar to aluminum in its chemical reactions that it is not separated from aluminum in ordinary chemical analyses. The principal ore mineral of beryllium is beryl, a beryllium-aluminum silicate, which contains only 5 percent beryllium. This mineral is so similar to quartz in appearance that it is not always possible to distinguish one from the other in the field. While the distinction may be made easily with a petrographic microscope, few prospectors have access to such an instrument, and fewer still know how to use it.

Jan 1, 1960

By A Mooney, G Balog, P Burns, R Brooks

This paper outlines the rationale for the location of the crusher, geotechnical analysis and basis of ground support design, design and scheduling of the chamber and supporting excavations as well as the operational outcomes and lessons learned. Contributions from mining operations, planning, geotechnical and infrastructure teams enabled the Crusher Station One excavation to be completed on schedule, with opportunities taken for underground mining and infrastructure to work safely in parallel to deliver crusher station infrastructure on schedule. Installation of crusher infrastructure was ongoing at the time of writing.

Mar 15, 2021

By Jamal Rostami, Levent Ozdemir, Amund Bruland, Filip Dahl

Cerchar Abrasivity Index (CAI) is one of the commonly used tests to evaluate rock abrasiveness for cutter life/cost estimations of TBM projects. There are at least 3 style machines, 2 different pin hardness, and the test could be run on fresh rock surface VS a sawn surface. Each of these parameters has a meaningful effect on the results, but its impacts were not fully understood nor its implications well explored. This paper reviews the current practice of Cerchar testing and its implications on geotechnical investigations related to TBM tunnels and provide a set of guidelines on testing and reporting of the test results for future projects.

Jan 1, 2005