Search Documents

By Matteo Montesi

Deep foundation elements are often used as discrete elements in externally supported earth retaining structures such as soldier piles and lagging walls, secant/tangent pile walls, anchored walls, etc. These structures can be designed using different approaches such as conventional limit equilibrium methods, finite element/difference analyses, and soil spring (p-y) analyses which are contained in various commercially available computer programs used by engineers worldwide. Although these programs usually undergo various degree of verification and validation, users must be aware of each program’s limitations and conditions in which each design approach should or should not be used. These programs may incur difficulties when non-continuous deep foundation elements are used as part of the retaining system and in cases of non-uniform geometry where closed-form solutions are not available. Design input parameters such as passive arching width, wall-to-soil friction, and p-multipliers (pm) are not always given enough attention which may result in potential design deficiencies. This paper presents the main features of various earth retaining structure design approaches and discusses their advantages/disadvantages. The paper addresses some of the limitations and difficulties that may be faced with when utilizing non-continuous discrete deep foundation elements and identifies key elements that are sources of potential deficiencies and errors. An example comparing the design outcomes using different design approaches is presented. INTRODUCTION Earth retaining structures are used to retain soil and create or maintain a difference in ground elevation between grades in front and behind the retaining structure. Deep foundation elements have been used for decades to support earth retaining structures. Earth retaining structures that are supported by deep foundation elements are typically referred to as externally stabilized system (O’Rourke and Jones, 1990). An externally stabilized system uses an external structural element, in contrast to internally stabilized systems which rely on reinforcements installed within and extending beyond the potential failure mass. The design of externally supported retaining structures can be accomplished using different approaches, which can be challenging under certain conditions. Each approach has been discussed extensively in available literature, and is well summarized in the and Federal Highway Administration (FHWA) guidelines. The objective of this paper is to present the most widely used design approaches and discuss their limitations and difficulties in one concise and brief document, giving the reader a good source for comprehensive understanding of the various design approaches, supported by a technical example. This paper is not intended to be a comprehensive review of all available design methods and formulations available in the literature.

Jan 1, 2018

By A. D. S. Gillies

The use of refuge chambers for use in handling underground emergencies is an issue of topical relevance within the US mining industry. Chamber design is of importance to meet some new safety requirements of US federal and some state government mine regulations. A review has been undertaken of a steel mine refuge chamber design to predict what will be internal temperature within the chamber over an extended period with miners present? The design has been examined for the situation when the chamber is sited in still mine air. Spreadsheets have been developed to allow various design assumptions to be tested. The evaluation has been undertaken using thermodynamic heat transfer models with some assumptions specified to produce a model of appropriate simplicity but with adequate degree of accuracy. Under normal still air conditions it can be seen that internal chamber conditions rise quickly to often arduous conditions. There will always be quite a few assumptions necessary in complex heat transfer process evaluations. Some important refuge chamber design parameters are: ? External surface area of the chamber, its wall thickness and construction. ? Metabolic heat generated and number of persons making use of the chamber. ? The temperature of the external mine atmosphere to the chamber over the year and the influence of geothermal gradient on temperature at depth. ? The maximum internal chamber Apparent Temperature considered safe. ? The distance inside the underground mine and adjacent ventilation conditions.

Jan 1, 2012

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel's support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

By B. Gigas, M. Preston, M. Giralico

Optimized mixer settler designs will now handle total flows of over 6,000 m3/hr.Computational Fluid Dynamics (CFD) is a timely and predictable tool for design development. Lightnin has the capability of using numerical analysis methodology to evaluate flow patterns and phase separation. CFD can show performance differences between changes, in mix tanks, in settler geometry, and in liquid depth, against variable flow rates. Understanding the differences allows the development of optimized designs. This paper focuses on the major design components of the mixer settler and how technological advances will lead to further improvements, when designing for today’s largest flow plants.

Jan 1, 2004

By Laffin N. W

Invariably when a new plant is cammissioned operations personnel on takeover look at ways and means of reducing certain restrictions and improving process conditions. These improvements are generally of a mechanical/engineering nature with minor metallurgical alterations to fine tune and maximise recovery. Most operations are continually reviewing and updating existing equipment and equipment spares to gain the maximum performance hereby reducing operating costs. Design of current carbon-in-pulp/carbon- in-leach (CIP/CIL) plants has evolved to such a high degree that many of the medium sized plants can have a "blue printed" design from one to the next if the same engineering designer is used.

Jan 1, 1989

By A. Kepeski

Cement industry relies heavily on the control of large volume of raw materials in the proximity of plant operations for clinker and cement manufacturing. These mineral resources are perhaps considered as ?low-profile? (mostly comprise limestone's, clays, marls and sands), but their availability, accessibility and suitability ? the later with respect to chemistry, mineralogical and physical characters ? are factors of paramount importance and may largely affect production cost and plant productivity. The combination of scarcity of good quality raw materials deposits and the growing environmental concerns have challenged the cement producers towards sustainability and the responsible exploitation of natural resources. In open pit mining and quarrying, the evaluation of mineral resources vs. handling of the non-usable overburden and other off-spec materials directly affects the medium to long-term production planning, quality control practices and environmental management. It is a general trend for many cement producers and a usual case for a number of Titan Cement plants worldwide, that redesign of quarry pits is necessary not only for stability purposes but also as a result of environmental constraints and emerging issues. The material reserves then have to be re-evaluated in the light of the new final pit design, safety distances from houses, other infrastructure and Law restrictions and according to criteria of safety of operations, reduction of environmental impacts, pit optimisation and proper future reclamation. The paper discusses the case of three active quarries of Usje Cement Plant, in Skopje (Macedonia), namely Usje (marl), Goverlevo (lime-stone) and Ljubosh (sand), where a large campaign of redesign and evaluation of recoverable reserves and the needs in rehabilitation took place in 2004. Technical and environmental issues and criteria are presented in the form of master plans and the highlights of the first attempts to propose and apply a reclamation scheme are discussed, by also examining alternative solutions for each quarry area. Finally, the 2005 progress in applying changes to the design of benches and pit layout, as well as experiences gained, are discussed.

Jan 1, 2005

By Steve Dubnewych

The Joint Water Pollution Control Plant, operated by the Sanitation Districts of Los Angeles County, treats wastewater generated by over three million people. A new tunnel and ocean outfall is being considered to meet future hydraulic demands and provide long-term redundancy for the Districts? existing tunnels, portions of which were constructed as early as the 1930s. The detailed process used to evaluate the feasibility of various tunnel and out-fall locations is described. Challenges include a geologic profile with mixed face and squeezing ground conditions; high water pressures; active fault crossings; gassy and contaminated ground conditions; and liquefaction, slope stability, and lateral spreading concerns in the area of the riser and diffusers.

By D. Anthony, R. A. Williams, R. Raponi

Barrick Gold Corporation in conjunction with SNC Lavalin Engineers and Constructors have developed basic engineering design for counter current decantation thickener (CCD) plants capable of processing 44 000 t/d. To achieve this throughput in a single train, the largest high-rate thickeners installed to date have been utilized in concert with large process slurry and solution transport systems. Process reliability and plant operability and maintainability have been carefully considered in order to develop a practical, yet cost effective design. The design also incorporates the challenges associated with installation of large equipment and structures in a remote location, with a climatically hostile environment, situated in a high seismic activity zone.

Jan 1, 2002

By Cameron J. Clayton

Cumberland Resources Ltd. is currently planning to develop the Meadowbank Gold Project located some 70 km north of Baker Lake, Nunavut in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of up to 6 main gold bearing deposits within relatively close proximity to one another which are planned to be mined primarily as a truck-and-shovel open pit operation and using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of 8 to 10 years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11 °C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site, and the physical environment, pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project.

May 1, 2004

By Witold J. S. Ostrowski

The shaft structure being part of an underground mine, depends on programned functional duties, and on geological and hydrological conditions. The majority of Canadian metal mine shafts are in hard competent igneous rocks, which are in an elastic state of equilibrium around the excavation. Others penetrate soft sedimentary or very weak water-bearing rock formations in which the equilibrium varies from plastic to hydrostatic. Knowledge of how to interpret the underground conditions, determine acting forces and design proper structures is essential for the production and safety of the future mine.

Jan 1, 1973

The application of reinforcement techniques to enhance the stability of underground coal mine roadways subject to high stresses is discussed. Research conducted in the Illawarra Coal Measures has been aimed to delineate the factors which influence the behaviour of rock above roadways and the performance of the reinforcement placed. Design considerations for the reinforcement of mine roadways in the Bulli coal are based on a quantification of the rock response together with a reinforcement strategy to enhance the structural integrity of the roof strata.

Jan 1, 1986

By R. D. Begley

This paper will present detailed design drawings of a flexible single floor residential superstructure proposed for both longwall and room and pillar mining conditions. All efforts were made to provide an immediately available economical alter- native for future home builders on subsidence prone land. Based on this fact, a basement was not included in the design because additional costs and measures would be required to minimize cracking and leakage. A cost comparison with a traditional superstructure demonstrated that this would be a cost effective alternative. The criteria used to determine the design of the residential structure was as follows: 1. The appearance should not be different then a typical three bedroom residence; 2. Only commercially available devices and present architectural and engineering technology should be used to achieve the required "flexibility" of the super- structure; 3. The structure as completed would be capable of resisting a predetermined amount of vertical and horizontal movement; and 4. If the structure was to experience stresses beyond its capabilities, it could be easily removed from the foundation and releveled.

Jan 1, 1986

By Yunqing Zhang

The 3-D numerical modeling using ABAQUS is performed to analyze the mechanisms of the tensioned bolts by taking into considerations excavation sequence, pre-tension, bedding planes and in-situ horizontal stresses. The effect of the pre-tension and the mechanisms of the tensioned bolts are analyzed based on the results from the modeling. Based on field observations, the failure modes for the tensioned bolted strata are classified by their causes and failure mechanisms. The support design consideration for each failure mode is given. Finally, a new design approach is proposed to do the tensioned bolting design using numerical method.

Jan 1, 2002

By A. Haines, O. Varaud, I. Baidoo

Abosso Goldfields Limited (AGL) is in the process of developing an expansion of their Damang Open Pit gold mine in Ghana. AGL acquired the Damang mine in January 2002, with SRK participating in the geotechnical investigation and design for the project since 2001. A deep resource drilling program, completed during 2004, intersected an extension of the orebody below the then planned final pit floor. A feasibility study has been completed to determine the economic extraction of this deep ore with an expanded pit shell. The Damang mine is in a stockwork sulphide deposit at the culmination of the Damang anticline. The deposit occurs as hydrothermal mineralisation associated with dominantly east dipping thrusts and sub-horizontal quartz veins. Primary gold mineralisation also occurs in the conglomerates of the Tarkwaian Formation. The geological units consist of steep easterly dipping dolerite, sandstone, siltstone and phyllite beds, with the weathering profile comprising saprolites overlying a relatively thin joint oxidized horizon. It is planned to deepen the current open pit to a final depth of up to 270 m, primarily by the development of a push-back of the eastern and western walls. The edge of the Eastern Tailings Storage Facility (ETSF) is currently located within 80 to 100 m of the crest of the existing pit. The geotechnical design focused on the optimization of the bench face angle and finally recommended a ?Steep Slope Strategy?, involving 24m high near vertical benches. Limiting bench stack heights of 96m at a maximum of 66° were derived from the influence of major structures and the variation in rock mass conditions. The overall slope angles in each pit sector were developed around the requirement for haulage ramps. One of the main design challenges was to optimise the standoff distance between the final pit crest and the ETSF. This process had to consider maximum access to the resource without undue influence on or from the nearby tailings dam. A planned increase to the height of the dam wall was an additional factor in the design. Dewatering of the pit walls was also a major consideration in this tropical environment.

Jan 1, 2006

By Thomas M. Barczak

Advancements in support technology have occurred to a large extent because of the demands of the mine operators. Shield supports are no exception. The most notable changes in shield technology in the past decade have been increases in shield capacity and life expectancy, which have increased by a factor of 4 and 7 respectively since the inception of the shield support 25 years ago. The purpose of this paper is to set goals for the future generations of longwall shields. These goals include: (1) 100,000 cycle life expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control with adjustable setting pressure algorithms, (4) composite material design to reduce weight and increase shield width, (5) constant set leg cylinder design, (6) improved joint design to reduce wear and stress, (7) advancements in leg cylinder socket design, and (8) an instrumented shield to measure in-service structural component loading. These design issues will continue to push the envelope in longwall shield technology that has provided the safest and most productive mining system employed in the history of mining. In preparation for this, a historical examination of shield failures is made and recent trends in shield design are evaluated. Design practices to improve structural margins of current designs are also addressed.

By Michael J. Lehnen

Slurry diaphragm walls are commonly used as both temporary excavation support walls, and permanent structural walls, for circular shafts and long rectangular structures (such as underground subway stations); however, they are not commonly used for more compact rectangular or square shafts. In these instances, a second wall is typically cast inside the slurry walls to form the permanent structure. This paper discusses the approach used on the Silicon Valley Rapid Transit Project in California to analyze these compact rectangular types of structures for static and seismic loading, and to determine whether or not slurry walls can be confidently used as both the temporary and permanent walls for two tunnel ventilation shafts.

By Charles A. Stone, Eric C. Wang

"Top-down wall construction was selected to excavate the tunnel portal headwall areas of the ORB East End Crossing tunnel. Benefits included an expedited construction schedule realized by staging excavation and rock support with development of temporary construction access roads. Rock mass properties, proximity to right-of-way lines, and blasting impacts were considered to design suitable lift heights, intermediate bench locations, and permanent ground support systems to provide supported permanent excavations. Carbonate rock formations contained adverse subsurface geotechnical features including solution cavities, clay seams, weathered joints, pinnacled rock, and boulders, which were addressed by flexibility in design. The resulting over-break conditions and long-term water infiltration issues required economic design solutions. This paper discusses the unique considerations required during design of top-down tunnel portal headwalls excavated in carbonate rock formations including temporary excavation and permanent ground support systems which provided flexibility for unforeseen over-break, minimized construction delays, and provided long-term stability. PROJECT BACKGROUND The East End Crossing is an approximate 8-mile highway connection of the Louisville-Southern Indiana Ohio River Bridges East End Crossing (ORBEE) project. Currently under construction, this connection will link State Road 265 in Indiana with the Gene Snyder Freeway in Kentucky to form an outer loop bypassing the Louisville-Southern Indiana metropolitan area. This highway project features a 2,510-foot long, three-span cable-stayed bridge over the Ohio River, and a 1,680-foot long tunnel. The project, being managed by the Indiana Finance Authority and Indiana Department of Transportation, is scheduled to open to traffic by the end of 2016. The new twin three-lane tunnel under the historic Drumanard Estate requires steep cut excavations for approach and tunnel portal walls on the order of 60 feet deep through overburden soil and carbonate bedrock formations. This paper focuses on the design considerations for the permanent support of the top-down wall construction of the tunnel portal headwalls and approach retaining walls."

Jan 1, 2016

By Mohammed Z. Islam

As cities are growing all over the world, the need for urban transportation facilities are on the rise. Designers (of these facilities) today are faced with a number of constraints for their design, of the most is the space limitation and impact of new construction activities to the community. A typical subway station, as the focus of this paper, is approximately 600 to 1000 feet long, 50 feet wide and 2 to 3 story high. With such a large volume of construction activities, it is easily realized why underground stations are becoming obvious choice for larger cities eventhough the cost could be 2 1/2 to 3 times as much as an aerial station and 4 to 5 times that of an at-grade station [O'Neil et. al.(1977)]. Since cost is an important factor which is always increasing, therefore, the designer should have a good planning, consider alternatives for design and come up with a realistic design with minimum impact to the community. This paper is about the geotechnical considerations that the designer should be aware of. PLANNING A 1977 report [O'Neil et. al.(1977)] on the construction costs for a number of underground subway stations indicate that about 4 0% of the cost is site-controlled, 35% is structural items, and 25% is finish and equipment. It is seen that of opportunity exists for cost savings in the site selection and proper use of the site. Once the site is selected, the cost of construction become controlled by urban conditions at the site, geotechnical conditions, station size and depth. Therefore, the design-solution is very much site-specific. The geotecnical designer should collect the following information at the early phase of the design:

Jan 1, 1993

By T. McKeon, G. Luttrell

Spiral separators are commonly used to upgrade sand-sized particles in both the coal and mineral processing industries. Many plants utilize multiple stages of cleaning and/or scavenging spirals to improve recovery and/or final product grade. Field studies suggest, however, that the layout of industrial spiral circuits is often less than optimal. This oversight can usually be attributed to a failure by plant designers to consider fundamental process engineering rules that govern the layout of complex separation circuits. This article reviews some of these important rules as specifically applied to multistage spiral circuit design. Two industrial case studies, one involving the upgrading of heavy mineral sands and a second involving the cleaning of fine coal, are presented to illustrate the impact of good design protocols on spiral circuit performance.

Jan 1, 2007

By Paul M. Wiltcher

This paper discusses how benefits in engineering design can be achieved from combining existing GRP concrete design guidelines with carbon steel design codes primarily made possible due to the increase in the constitutive properties of modern composite rebar or GRP. It also examines the technical and practical considerations necessary to both construct and ensure the integrity of composite rebar during transportation and handling on site and the measures taken by Franki-Cementation Joint Venture to ensure the safe deployment of the GRP in the workplace on the Noord/Zuidlijn Project in Amsterdam between 2003 and 2006.

Jan 1, 2006