Search Documents

By Gerald L. Stolarczyk

Safe and efficient coal extraction requires advanced radar subsystems that can be mounted on cutting drums of coal cutting machines. A look-ahead radar (LAR) must solve the radio geophysics problem of transmitting an electromagnetic (EM) wave through at least 20 feet (6.1 meters) of coal to an air- or water-filled void. The reflected EM wave must be processed in the radar electronics to determine the physical distance to the void. Horizon sensing enables selective cutting near the undulating sedimentary rock boundaries of the coal bed to address coal quality and ground control issues. Both sensors require subsystems for dynamic electric power generation, real-time measurement of drum rotation angle, detection of reflected EM waves, and processing to determine distance through coal and RF modem transmission of measured data to the mining machine. This paper describes the development of the subsystems and field test results.

Jan 1, 2006

By E. Munnik

The Chambishi Metals Cobalt Plant in Zambia has recently installed a novel oxidation/precipitation pressure leach process as part of the COSAC (CObalt from Slag And Copper as by-product) Project. Aniron-cobalt-copper alloy, produced by the carbothermic reduction of slag, is atomized and pumped to the COSAC Leach Plant, where cobalt and copper are recovered as dissolved sulphate salts, andiron is rejected primarily as hematite. Cobalt and copper are subsequently recovered as cathode metal in the existing Chambish ioperation by conventional electrowinning. This paper examines the challenges faced during the design and subsequent successful commissioning of the COSAC Leach Plant. The challenges discussed include alloy handling, autoclave design, autoclave cooler design, residue liquor recovery and the water balance design. Keywords: Chambishi, Avmin, COSAC, Zambia, Copperbelt, cobalt, copper, alloy handling, pressure leach, autoclaves, cooling, filtration.

Jan 1, 2003

By A van Jaarsveld

Environmentally-friendly, safe and cost-effective technology for stope drilling has successfully been introduced at TauTona mine. It has enabled the problem of inadequate compressed air pressure and its downgrading impact on production capability to be overcome. The paper traces the development process which culminated in the conversion of the entire stoping operation at TauTona to electric drilling. Background work which took place at other mines is also described. Statistics of performance improvements are provided. 1. Introduction Holman?s Silver series and the Seco S215 were drills that had a measurable impact on the South African gold mining industry. It is too soon to say whether Hilti will join those great names. However, there is no doubt that the introduction of electric drills into the harsh and unforgiving world of deep level gold mining is a significant development. History has shown that being the first to enter a new technology is no guarantee of long-term success. The pain and suffering which accompany the birth of anything new can deplete the energy of the innovator while at the same time creating opportunities for competitors to leapfrog him. In addition to commitment and enthusiasm, the innovator must therefore also possess, or have access to stamina and resourcefulness to overcome the unexpected difficulties which will inevitably arise. All of these were needed for the Hilti project.

Jan 1, 2008

By H. Ewaschuk

"INTRODUCTIONRio Algom's Stanleigh Mill in Elliot Lake began production in June of 1983. The highly instrumented mill treats uranium ore at an average rate of 3900 metric tons per day. To help ensure a good start-up and low operating costs, an extensive training program was undertaken prior to and during start-up. This presentation describes how an unconventional operating crew were combined to form an operating unit with a high efficiency in terms of production and labour utilization. I would like to point out at the outset that the operating philosophy, and the role of the supervisors and the operators as set up at Stanleigh is not unique. Indeed, I have seen the same results at a couple of small plants where efficiency meant survival. However, these situations appeared to be the exception, and it was not readily apparent how similar results could be obtained in a larger plant. A factor that existed at the time was low labour turnover. As in most parts of Canada, jobs were easy to get in the Elliot Lake camp in the late 1970's. This, and other factors, contributed to an unusually high labour turnover. This changed dramatically in the early 1980's. Indeed, Rio's two other operating mills, Quirke and Panel reduced crew sizes at this time to reduce operating costs. As a result all of Stanleigh's operators came from Quirke and Panel with experience varying from 4 to 7 years. The experience that operators had was obviously of benefit and served to reduce the scope of the training program from what would have been required with inexperienced personnel."

Jan 1, 1985

By David A. Heitman

The Buick Concentrator is a highly automated operation which utilizes a process control system for continuous monitoring and control. The process control system development, installation, and application to the concentrator grinding and flotation circuits are presented in this paper. The design and implementation of analog field sensing instrumentation, a continuous on-stream X-ray analyzer, grinding and classfication circuit controls, and a recent digital process control system utilizing a centralized computer are discussed. Emphasis is placed on the project planning and installation of the digital control system including a presentation of future plans for continuing application of computer control.

Jan 1, 1982

Effective tools are not only essential for the design of practical and efficient underground mine ventilation systems but must also play an integral part in the operation of the mine. One such tool is VUMA-coal ventilation simulation software. VUMA-coal is Windows-based and has been specially designed for the simulation of underground coal mines and includes user-friendly coal specific interfaces and three-dimensional graphics designed to facilitate in the construction and analysis of networks. VUMA-coal can be utilised during the design phase of new collieries, be used to conduct ?what-if? and optimisation studies, and be integrated into the ?day-to-day? ventilation related operations. In addition, VUMA-coal can be used to simulate dust and gas distribution in a ventilation network, as well as predict the impact of control measures. This paper describes the interactive VUMA-coal ventilation simulation software and its underlying design features and outlines a case study of how VUMA-coal has been integrated into Anglo Coal?s Ventilation and Occupational Hygiene Engineering [VOHE] department as part of the standard planning and evaluation process in their operational mines as well as long term planning and future mining operations.

Jan 1, 2009

By Robert M. Semple, Harvey W. Parker

INTRODUCTION Two promising innovative tunnel support systems are being developed by the Civil Engineering Department of the University of Illinois. One of these is a lining which can be placed by a slipform located immediately behind and contiguous with a tunneling machine. Recent advancements in construction materials appear to provide the breakthrough required to make such a system feasible and practical. The lining material which permits this construction scheme is wire fiber reinforced concrete made with high, very early strength regulated-set cement. Parts I and II of this paper relate to this slipformed liner. Part I discusses the material and equipment required to install the liner. The "Extruded Liner System" (ELS) has been devised to place the lining. This ELS concept is briefly described and a tentative development program is outlined. In Part II, the physical properties and practical construction aspects of the liner material are discussed and a program for structural testing of 10-ft diameter prototype tunnel supports is presented. Part III contains descriptions of improvements to conventional steel-rib tunnel supports. It is shown that square tubular box sections are structurally superior to wide flange sections for complex loading conditions often encountered in rock tunnels. Analytical studies and tests on connections have been performed to evaluate their structural behavior. These are presented along with a program for comparative large-scale tests on horseshoe-shaped frames with a 10-foot span. This research is being conducted by the Department of Civil

Jan 1, 1997

By Fred K. Stieler

The largest updraft sinter machine built has a roasting area of 132 sq.m. Sinter machines with an area of over 200 sq.m. are under consideration. These large machines require new techniques with regard to drive thrust and sealing mechanism. To optimize the results of sinter plants, the charge preparation systems and the return fines circuits were improved. Special crushers were developed for crushing return sinter of up to 800 ºC to a size of minus 6 mm. Strand cooling of Pb-sinter was investigated. Different methods for plant ventilation were compared. New processes, which might replace sintering in the future, are in the stage of large - scale testing.

Jan 1, 1977

By Waghorne E. P

The State Electricity Commission of Victoria is Australia's largest single coal producer. Approximately 19 Mt of coal will be produced in 1989 from the SEC V's newest mine, Loy Yang Open Cut (LYOC), which com- menced overburden stripping operation in October 1982. When the adja- cent Loy Yang Power Station is completed in the late 1990's, LYOC will supply between 35 to 45 Mt/a, depending on power station performance and demand of coal for non-power generation uses. LYOC has been a major challenge for the SECV. It is the biggest single open pit coal mining development undertaken in Australia, with a whole of life capital cost approaching A$1 billion. The mine has supplied a very rapidly growing demand for coal from the expanding power station while developing in breadth, length and depth. Coal demand has consistently been above the figures anticipated during the initial planning because of the substantially improved performance of the 500 MW units of the Loy Yang A Power Station. The superior performance of the LYOC and power station has generated additional electrical energy during the first 5 years of power station operation compared with the initial planning targets- at almost no additional capital cost. This has been a major benefit to the SECV. LYOC will continue to present major challenges for the SECV, particularly in achieving overburden removal and coal reserve targets as development of the open cut continues to full depth over the next 15 years.

Jan 1, 1989

The development of the Moura Coal Preparation Plant is described, commencing with the first'stage of the plant commissioned in 1963. The subsequent expansion stages are traced through to October, 1973. The plant has undergone frequent stages of expansion and modification and this process is continuing. The development programme for 1974 is described as proposed in late 1973. The characteristics of the Moura and Kianga field coal seams with respect to washability are summarised and some comment is made on the blending of these coals prior to washing, to ensure production of export grade coal within specification.

Jan 1, 1974

The Racecourse Orebodies at Mount Isa consist of a series of parallel steeply dipping lead/zinc/silver orebodies with a strike length of up to 1000 metres. Production from these orebodies between 13 Level to 9 Level has been by a series of cut and fill stopes in two level stages, leaving a crown pillar at 11 level. Development of the 15 level to 13 level extraction stage has recently been completed. The layout consists of a series of parallel stopes over a strike length of 1200 metres. Access to the stopes is by two declines connecting the stopes with a series of crosscuts This paper describes the basic layout with development and production methods employed.

Jan 1, 1977

By Nathaniel Arbiter

Flotation’s earliest patent was issued in 1860. However, the process was first applied commercially in Australia until 1904, and in Montana in 1911. Major advances followed both in reagent treatment and in cell design, with resulting process improvements. Mechanical cells have seen the widest use and with the major increases in plant capacities (Fig. 1) their volumes have also increased (Fig. 2). In 1991, the principal use for the process was to produce copper concentrates for smelting. It was applied to 243 Mt (268 million st) of copper ore. The total of all ores floated that year was 426 Mt (470million st). In 1997, US mines produced 257 Mt (284 million st) of copper ores for flotation, yielding1.75 Mt (1.94 million st) of copper.

Jan 1, 2000

By Shuangchun Yang, Le Tong, Ronggui Fan, Cunlei Li

Acid mine drainage (AMD) is difficult to treat due to its physicochemical characteristics, such as high pH and high heavy metal concentrations, so it causes great harm to the environment and human health. If acid mine drainage is discharged arbitrarily without treatment, it will lead to a series of environmental problems and cause long-term environmental pollution. In this paper, the source and hazards of acid mine drainage are introduced in detail. And the principle, the mechanism, the application, and basic information of the current primary technology of the treatment for acid mine drainage are comprehensively introduced and summarized. The summarized treatment technologies for acid mine drainage mainly include neutralization, sulfidization, constructed wetland method, adsorption method, microbiological method, ion exchange method, membrane technology, and microbial fuel cell technology. Also, the primary technology of treatment for acid mine drainage is systematically compared and evaluated. Moreover, some suggestions on the development direction of water treatment technology in the future are put forward. This paper provides a scientific reference for scientific and technical works to treat acid mine drainage.

Sep 4, 2020

By P. S. Paul

Mine accidents/injuries are complex and generally characterized by several factors, from technical to social characteristics. In this paper, a sociotechnical model for work injury in mines was developed and tested through structural equation modelling with application to case study mines in India. In total 14 variables were considered in this study. Most of the variables are not directly quantifiable. Instruments were developed to quantify them through a questionnaire survey. Underground mineworkers were randomly selected for the survey. Responses of 300 participants were used for the analysis. The analysis was conducted in three parts. Firstly, high-low plots were constructed to explore the variations in responses to the questionnaires by the accident involved (AG) and non-involved (NAG) workers. Secondly, a t-test was conducted to see whether the responses were significantly different for the two groups or not. The chi-square results showed significant differences of responses among the two groups. Finally, how these difference scan cause accidents/injuries in mines was hypothesized and evaluated using structural equation modelling. The measurement model of the Linear Structural Relations (LISREL) program was used to identify the latent constructs of the sociotechnical model. The structural model of LISREL was used to estimate the interrelationships among the constructs. The case study results showed that there is a sequential interaction among the sociotechnical factors leading to accidents/injuries in mines. Work hazards induce more job stress in the workers while social support mitigates the same. Job stress and safety environment predict the workers? job involvement. A worker who is more job-involved exhibits better safety performance, which in turn reduces work injury. The safety environment is shown to have a direct mitigating effect on work-related injury. The findings of this study clearly revealed that job stress and safety environment are the two key factors influencing work-related injuries in mines that need to be addressed properly through effective safety programmes.

Jan 1, 2005

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By A. Nieto

A vehicle proximity warning–collision avoidance system is being developed using GPS and wireless local area networks to improve safety of off-highway trucks in open pit mines. After two-and a-half years of research, software development, and laboratory testing, field tests were carried out at operating limestone quarries and open pit mining operations to evaluate GPS accuracy and overall system effectiveness under rugged operating conditions. This article describes the progress made on this NIOSH-funded project and discusses the GPS accuracy tests and overall system tests that were carried out during the year 2001 at the Colorado School of Mines Survey Field and at the Morenci open pit copper mine in Arizona. Keywords: GPS, Advanced Mining, Virtual Reality, Wireless Networks, Proximity Warning

Jan 1, 2003

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

Development and Validation of Ore Characterisation Test and its Use in Variability Campaigns of Comminution Circuits Impact testing was developed by assessing the fragmentation characteristics of ore samples after controlled impact. Standard methods are, however, limited to relatively large and coarse samples, which thus precludes their use in early stages of projects, as well as where only drill cores are available. The method described in this paper is based on the same concepts of controlled ore breakage, but using relatively smaller samples. It is particularly useful in assessing the variability of ore characteristics in early stages of greenfield projects, as well as in predicting the performance of existing grinding circuits. A validation program was carried out in which a good adherence to the original test results was obtained. The results were used for (a) simulation of a copper comminution circuit as a function of the ore characteristics, and (b) evaluation of sampling protocols used for assessing fragmentation characteristics.

Sep 13, 2010

Permitting, engineering and evaluation, detailed design and construction aspects of the Golden Cross goldmining project in New Zealand are briefly reviewed. The extremely lengthy and complicated governmental approval process together with the delaying tactics of opponents of the project are outlined and comment is made on aspects of the draft legislation proposed as part of the overhaul of New Zealand's resource management laws.

Jan 1, 1990

By C. C. White

Much benefit can be achieved by a mining company and a manufacturer if both parties can communicate effectively with each other and assist in product development; mutually beneficial ideas and products will develop. This communication can best be achieved if both parties have the opportunity of having on their respective staffs, specialists whose function is to improve the use of products used in mine development. Although a great wealth of roof control knowledge has long existed among mine operators, until recently there was not an abundance of joint development of roof control material by manufacturers and mine operators. This was perhaps due, in past lean years, to the preoccupation of mine management with other overwhelming problems that arise in mining. Manage¬ment had little time for the lengthy process of product development. Until recently, only a few of the largest mining companies had fulltime personnel devoted to roof control. A bolt manufacturer who is invited to work with an operator's roof control people in developing new material is lucky indeed in that he learns what is wanted and he acquires the benefit of the operator's knowledge and experience. He has only to come up with a satisfactory product at an acceptable price - which is not always easy: The development of new products is usually costly and time consuming, and many new products fall by the wayside. In the case of point anchors, however, this product is here to stay. The advantage of point anchors over mechanical anchors is now a proven fact. This advantage is due to less bleed off and higher ultimate load capacity of the resin point anchors. Point anchored bolts have proven to be superior to fully grouted bolts in many areas. We at Birmingham Bolt Company are fortunate in that we have been involved in joint efforts to develop point anchors with several coal companies from whom excellent advice and direction was received. It is appropriate to mention before continuing that the use of point anchors began in the 1960's in Europe and became widespread only recently in the United States. They fall in two categories, point anchors and combination point anchors. These categories have been defined by the Bureau of Mines as follows: (1) point anchors having 24" of grouted length and (2) combination anchors having 24" or more of grouted length. In the present nomenclature, all are anchored with resin or some sort of cementing compound between the rebar or tensioned element and the wall of the hole. The latest development includes an expansion shell as well as rebar, the purpose of the expansion shell being to facilitate installation without the delay necessary in use of types that require a waiting periond for setting of the resin before tightening. (See figures #1 and #2.

Jan 1, 1982