Search Documents

A recently developed technique for use in collieries is described in which samples of gas of relatively high vitiation value are obtained from points deep within a developing goaf by means of pipes. This technique prevents dilution of small quantities of carbon monoxide by large quantities of fresh ventilation air and eliminates interference from shotfiring gases. By using the technique it should be possible to assign a characteristic ratio of carbon monoxide to oxygen consumed to any district and to predict the onset of heatings.INTRODUCTIONGas analysis has played a vital role in detecting heatings in collieries all over the world. By analysing return air from a district and by calculating the percentage ratio of volume of carbon monoxide found to oxygen consumed (known simply as the "carbon monoxide ratio") it has been found possible, in many cases, to assign a characteristic ratio to a district under consideration. This characteristic ratio serves as an index of the spontan~ous combustion tendency of a goaf area. Any definite and consistent increase in the ratioabove the normal figure· indicates that a heating is developing and hence adequate preparations may be made to deal with the trouble.This ratio technique was developed by Graham (1920-21) who found (Table 1) that the temperature of oxidizing coal was directly related to the ratio obtained from analyses of the effluent gas.Until recently, most attempts to employ a similar technique in collieries working the Greta Seam (N.S.W.) were not successful. From experience gained over the past few...

Jan 1, 1961

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

By J. M. Tannenbaum

A depth-sensing micro-indentation technique is developed for evaluating mechanical properties of materials at elevated temperatures (to 1200°C). System description and design considerations of the test apparatus are described. Based on Hertzian spherical indentation approach, the micro-indentation test apparatus is capable of determining Young?s modulus and creep strength of test materials with flat, tubular, or curved architectures from room to 1200°C under either air or controlled gaseous environments. Calibration tests were conducted on a H13 Tool Steel coupon from 22°C to 500°C and single crystal Haynes 230 alloy at 1000°C with excellent agreement to the literature values. Indentation creep tests of Haynes 230 alloy were carried out at 1200°C with preliminary results showing good correlation to creep exponents. Further system refinements will be investigated, and additional testing will be conducted.

Jan 1, 2010

By J. R. Klaehn, M. Shi, T. E. Lister, L. A. Diaz, J. S. McNally

Since 2019, approximately two dozen international battery recycling companies have been operating at the commercial or pilot scale [1]. However, current process capacity does not exceed 100,000 tons of end-of-life (EOL) lithium-ion batteries (LIB) per year, and the current recycling rate is only about 5% in North America [2-3]. Recycling metals from EOL LIBs is not only essential to waste minimization and environmental stewardship, but also a source of critical materials, which can contribute towards supply chain stabilization. LIB recycling can be roughly divided into three categories: direct recycling, pyrometallurgy, and hydrometallurgy. Direct recycling seeks to retain as much of the manufactured effort with minimum chemical processing [4]. The evolution of battery designs and chemical compositions are challenges to this approach [5-6]. Pyrometallurgical processes are robust and flexible allowing a broad spectrum of batteries with minimum pre-processing requirements. Some of the matrix issues are solved through combustion of some constituents. Smelting is strongly tied to fossil energy and air emissions are a concern. In addition, pyrometallurgical processes are not stand alone, as hydrometallurgical refining normally required to separate and recover the metals of interest (Co, Ni, and Cu) from the produced alloy and Li from the slag [7]. Hydrometallurgical processes can be highly selective and efficient in recovering high purity materials [8]. In general, hydrometallurgical processes are considered cleaner and less costly than high temperature processes [4,9-10]. Extensive chemical consumption and waste generation significantly increase the operating costs and overall environmental impact of the hydrometallurgical processes [11]. Leaching of metals from LIBs is dominated by the mixture of sulfuric acid (1 to 4 M H2SO4) and hydrogen peroxide (1 to 15 wt.% H2O2) [10]. Although organic acids have been tested as lower environmental impact alternatives, the reported pulp density operations are low < 60 g/L [10-11]. For the H2SO4/H2O2 leachates, high leaching efficiencies >90% are reported for Co, Ni, Mn, and Li from cathode materials at temperatures over 40 ⁰C and pulp densities between 30 to 200 g/L [9-10]. H2O2 acts as reducing agent to convert Co+3 and Mn+4 into their soluble forms, Co+2 and Mn+2 [12]. Despite the claims of H2O2 being a clean reducing agent [13], production of H2O2 has significant environmental impacts as determined by life-cycle analyses [13-14]. Moreover, the costs and risks associated with H2O2 transportation and storage cannot be ignored [15].

Mar 2, 2022

By Masaki Imamura

A novel hydrometallurgical process for copper concentrate treatment has been developed by Niihama Research Laboratories of Sumitomo Metal Mining Co., Ltd. The process has numerous advantages with respect to the operational and environmental aspects. For example, copper is leached effectively from chalcopyrite concentrates by chlorine gas under atmospheric pressure. The copper in the leach solution is then separated from iron and silver by solvent extraction and undergoes electrowinning for its recovery as a highly pure copper metal; this does not require any further purification. Moreover, iron metal can be produced from the purified raffinate by electrowinning without generating a large volume of goethite or hematite, which are solid wastes generated due to iron rejection in common hydrometallurgical processes. This process can also realize the efficient recovery of precious metals. The results of batch testing and continuous-operation testing are presented in this paper.

Jan 1, 2006

By C. Massola, E. E. M. N. de Guzmán, M. G. Bergermana

The abrasiveness of a mineral or rock is an extremely important topic in the mining industry and is generally measured by the Bond abrasion index (AI). However, to determine such an index by the Bond test requires 1,600 g of sample with particle sizes ranging from ½” to ¾”, which are not available in certain situations, such as ore prospecting, drilling, and geometallurgical studies. In order to investigate the abrasiveness of smaller-sized sample materials, a modified LCPC test was developed, which allows testing fine materials (i.e., 1.0 mm or smaller) to predict wear in ore processing circuits and anticipate possible failures resulting from changes in abrasive characteristics of the ore being processed. The results for 16 different materials indicated a good correlation with the AI and the modified LCPC, resulting in a reliable alternative for the AI. Keywords: Bond Abrasion Index (AI), LCPC, abrasiveness

Jan 1, 2020

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

By Ryan W. Ulansky

This paper presents the conceptual design of a magnetically-levitated skip for use in an underground mine. A skip is used to move rock from an underground mine to its surface processing facility. Conventionally the skip is raised and lowered by cables, similar to an elevator. In a magnetically-levitated skip, the cable is replaced with a linear induction or synchronous motor to provide propulsion and levitation. Removal of the cables in a magnetically-levitated skip provides many advantages over a conventional system including the ability: to negotiate corners, to travel vertically in the shaft as well as horizontally to the mining face, and to move a very large volume of material using multiple skips in a small shaft. A magnetically-levitated skip is a safer, more environmentally-friendly, productive alternative to conventional skipping. It has the further advantage to decrease haulage distances for underground vehicles.

May 1, 2002

By L. Bircumshaw

Paper written on project work carried out in partial fulfilment of BSc (Eng) (Chemical) degree This paper details the formulation of a mathematical model for the simulation of a primary bioleach reactor, with specific reference to the leaching of pyrite. The model is based on the direct reaction mechanism, where the leaching of pyrite is said to occur via a two-step process. The process involves the formation of ferrous?iron through the chemical leaching of pyrite and subsequent bacterial oxidation of ferrous-iron back into ferric-iron. At steady state the rate of chemical leaching and bacterial oxidation are linked by the ratio of ferrous-iron to ferric-iron in solution. The extent of conversion of pyrite in the reactor system is described using the segregated flow model, with the exit age distribution of the solid phase being described by the Tanks-in-Series model. The final phase in model formulation involves the inclusion of steady state material balances on the bacteria and fluid phase components. The model is compared to pilot plant data and laboratory data for two different types of pyrite concentrates, with simulation results showing that the model is in good agreement with the data. Author key words: Bioleaching; pyrite; primary reactor; modeling; segregated-flow model; tanks-in series model.

Jan 1, 2006

By Camilo I. Morales

At present, many open pit mines are designed to operate and feed a processing plant with ore characteristics that were defined in the design of the mining business, which are not necessarily the same as those found during the operation. This is the case of Spence Mine, whose design was conceived considering the extraction of primary iron sulphides, however, with the extraction of such minerals, it was necessary to mine and process minerals with secondary enrichment. Then it is necessary to work with a greater selectivity degree in the operation, however the capacities of the mine and operational resources were not designed for this. Thus, the changes in the general conditions of the operation should be considered as a series of geometallurgical restrictions to achieve production schedules. The above facts impacts directly in the short-term planning, whose task is to achieve the goals proposed in productive long-term planning because the company does not have the tools necessary to plan with the degree of selectivity required, so it should be done by hand, discretizating and scheduling the production polygons. Naturally, this manual process in the short term planning deviate sharply from the areas in operation, opening new fronts and benches that result in a significant increase in costs and a loss of the value of the mineral resource to miss the exploitation sequence. The research presented in this paper is related to the development of a mathematical programming model to support the short-term planning, so as to integrate the challenge of selective mining with geometallurgy restrictions, to provide the planner a guide to construction of the polygon of exploitation, guiding the fines production to achieve the goals of the proposed production plan.

Oct 1, 2009

By Richard D. Begley

This paper summarizes the development of a mechanistic model to predict longwall mining induced surface subsidence. The model was originally developed from data acquired from a recent field study conducted in Northern West Virginia. Additional data has been collected from published sources and used to refine the model. The original model utilizes a negative exponential equation to predict the subsidence profile after the maximum possible subsidence is predicted based on the following input parameters: mine geometry, angle of draw and expansion factors for the deformation zones that have been identified above a longwall excavation. The model refinement involved the development of relationships between physical properties of the overburden strata and angle of draw in addition to the expansion or bulking factors. Therefore the refined model now requires only mine geometry and a typical geologic column from the site to predict the subsidence profile. This paper provides the methodology that enables the model to determine the angle of draw and expansion factors breed on physical properties of the site geology i. e. percent of strong rock and Rock Quality Designation of the overburden strata. In addition :comparisons of predicted results with measured data for over H) different sites with various geological and geometrical parameters located throughout the United States will be presented.

Jan 1, 1989

By T Preston

Solid Energy is the largest coal producing company in New Zealand, employing 500 people and more than 250 mining contract personnel. The coal produced by Solid Energy plays a significant part in the energy mix for New Zealand being supplied to the coal-fired power station at Huntly. It is also supplied to a wide range of industrial users, NZ Steel, and primary processing. It is fair to say however that the positive economic and social benefits of coal have to some extent been overshadowed by the negative environmental consequences of coal mining. &nbsp; Over the past two years Solid Energy have been actively researching and addressing the impacts that they currently have on the environment and making a significant investment in environmental improvements, rehabilitation projects and environmental research to address historical and ongoing environmental issues. These investments have been driven by the companyÆs commitment to its environmental policy, which states: &nbsp; æSolid EnergyÆs overall environmental objective is for the cumulative result of all the activities we undertake to have a positive net effect on the New Zealand environmentÆ. &nbsp; With such significant investment it is essential that the company is able to target expenditure wisely, ie invest where there is greatest environmental gain to be had, and are also able to actively demonstrate to stakeholders the improvements that are achieved. In order to be able to demonstrate the commitment and the steps that the company is making towards this goal a number of systems have been developed. Firstly an environmental management system along the lines of ISO14001 formalising the environmental processes, responsibilities, auditing and management review. Secondly as part of the planning element of the EMS an environmental management matrix, which allows the scoring of sites against environmental management goals, has been developed. Thirdly the monitoring and measuring tools have been upgraded with GIS driven relational databases installed for management of consent related information and monitoring results. &nbsp; The development of the environmental management matrix has drawn on a number of existing systems such as the Australian Institute of Mining and Minerals Code 2000. In addition to adapting the scoring regimes from these methods the Solid Energy Environmental Matrix has been further developed to ensure that it reflects the actual environmental impacts on site, as well as the management and audit systems that are in place to control them at a strategic level. The development of this matrix has included a number of steps: +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; reviewing the information that stakeholders would be interested in, +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; reviewing what was already available, +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; development of systems to collect data and benchmark the current&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; operations, and +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; setting up support systems to ensure that the correct information would be provided for scoring.

Jan 1, 2004

By J. A. Botín

In modern mining, the core of mine planning and design is the block model, a simplified representation wherein the ore deposit is divided in a number of virtual rock cubes, each characterized by technical and economics parameters. Mining engineers use this model to design the mine and develop production schedules. Traditionally, sustainability issues are not considered in the mine design, planning and engineering processes but rather are incorporated in the later stages of the feasibility evaluation as necessary expenditures and operating costs. This paper describes the results of a research project aiming to develop a methodology to incorporate sustainability parameters directly into the block model, so that they become an integral part of the design, planning and scheduling processes. It is considered that the incorporation of sustainable parameters into the block model would yield a more responsible mine design and improve mining projects sustainability performance

Feb 27, 2013

By H Zimba, S Sondashi, M Chitambo

By the time a reagent is finally accepted by a mine for use on its plant it could have gone through several screening and evaluation stages. These stages may include laboratory and plant evaluation testwork. This paper outlines the steps that were followed to select, design and implement a frother for KONKOLA COPPER MINES PLC Nchanga Copper Concentrator in Zambia. It discusses initial frother screening work conducted at the Betachem metallurgical laboratory and the subsequent laboratory screening testwork conducted at Nchanga Concentrator. A modified Bikerman test method is discussed which was used to design a frother for the Nchanga flotation plant. The paper also gives an account of several plant scale trials conducted on Nchanga flotation plant and discusses the plant results, frother consumption patterns and some commercial concerns, before the product was finally accepted by the mine.

Jan 1, 2007

By R. Karl Zipf, Z. T. Bieniawski

"Fracture mechanics plays an important role in studies of geologic materials such as rock and coal. Yet fracture data are scarce for rock and most limited or unreliable for coal. A testing system was developed which can apply mixed mode loads to a crack tip in many rocks and geologic materials. It is possible to subject the test specimen to pure mode I, various mixed modes and a nearly pure mode II fracture load. The system is currently used to study the mechanics of fine fragment formation in various coals. Experimental measurements include KI and KII' fracture velocity and acoustic emission.INTRODUCTIONA major research program at The Pennsylvania State University is directed to understanding the fundamental mechanics of fine fragment formation in various coals. The program represents an effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners. The principal source of the respirable coal fragments is the cutting operation which forms and liberates the particles by a fracture process. Present understanding of the mechanics of the events which form and liberate these particles is meager (Cook, 1982).Current knowledge of the fundamental mechanisms of coal dust generation and entrainment in terms of the underlying fracture mechanics is critically needed to improve and possibly control the processes involved. Whether the cutting operation is done with a 'continuous miner' cutting machine, a plow or a longwall shearer, it is fundamentally a problem of mixed-mode crack propagation. When a cutting tool interacts with coal, it causes numerous cracks to propagate through the intact material. Numerous larger fragments are broken free, but another quantity of undesirable fine fragments is also created. The formation of these respirable fragments may be a direct result of the crack propagation process; hence, a thorough understanding of the fracture mechanics of coal is required to minimize production of the unwanted fine fragments.In most rock engineering applications, the rock material properties are of secondary importance to the rock mass properties; however, for rock fragmentation and rock cutting problems, it is rock material properties such as fracture toughness which are of prime interest (Bieniawski, 1980). Several rock cutting and rock failure theories have been proposed, but it is only very recently that fracture mechanics concepts have been successfully applied to the study of rock cutting mechanics. All cutting models seek to predict the cutting forces and the cutter geometry necessary to cause rock breakage and chip formation given some fundamental mechanical properties ~f the rock. Such models have wide applications in drilling, tunnel boring and mining problems. Nelson et al., (1985, 1986) has provided a very useful correlation between the laboratory measured fracture mechanics properties of rock and the performance of the disk cutters on tunnel boring machines."

Jan 1, 1989

Milling circuits are known to be difficult to control. In order to address these difficulties, it was decided to develop and test a model predictive controller (MPC) for a milling circuit. A milling simulator was written using Microsoft Visual C++ and used to design and test the MPC controller. Due to the large number of tuning parameters in a controller of this type, an optimizing algorithm was written that automatically tunes the controller. Good, robust control was obtained when the controller was tuned using this algorithm. Control was further improved by combining feedback and feed forward control and by using quadratic programming in the MPC algorithm. The movement of the manipulated variables was reduced by using a novel technique that allows the controlled variable to vary within a specified region around the set point. An optimiser controller was also successfully implemented to control the circuit at its maximum throughput.

Jan 1, 2000

By A. Asadi

Subsidence phenomenon as an unwanted consequence of underground mining can cause problems for environment and surface structures in mine area. Surface subsidence prediction for inclined and steep seams has been given less attention than horizontal seams due to the difficulties involved in the extraction of such coal-seams. This paper introduces a new profile function method for prediction of surface subsidence due to inclined coal-seam mining. The results of calculation with the new function indicate that the predicted value has good agreement with the measured data. Keywords: subsidence; coalmining; caving mining methods; longwall mining; profile function.

Jan 1, 2005

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

By I. Bhattacherya

Over the last three decades, the mining industry has been moving towards underground mechanized mining methods and the number of load haul dump (LHD) vehicles utilized has increased. The growth of mechanization and automation has benefited both workers and mining companies. However, due to the design constraints with LHD vehicles and the limitations of the operating environment, restrictions to operator visibility has contributed to a number of accidents, including fatal injuries. Past researchers have used the light filament technique to collect obscuration zones around mobile equipment and have produced 2D visibility charts (shadow diagrams) of this information. The light filament method involves manually collecting visibility data, which results in errors and is time consuming, requiring around three hours to complete. This research utilizes a MENSI GS100 laser scanner along with 3D modelling software (3Dipsos) to collect and process operator visibility profiles for underground mobile equipment. Results from this test work indicate that a laser scanner can be successfully used to rapidly collect this data and utilize this information for improved mobile equipment design from a visibility perspective. Nomenclature FERIC Forest Engineering Research Institute of Canada ISO International Organization for Standardization JACK Software for digital human modelling and ergonomics LHD Load haul dump vehicle LOS Line of sight MASHA Mines and Aggregates Safety and Health Association (based in Ontario, Canada) PVD Polar visibility diagram SAMMIE3D human modelling computer aided ergonomics design system WSIB Workplace Safety and Insurance Board

Jan 1, 2006