Search Documents

By Wen-long Zhan, Zhe Ning, Jun-hong Zhang, Teng-fei SONG, Zhi-jun He, Qing-hai Pang

In order to investigate the influence of granularity on the gasification property of coke after microwave irradiation, comparison of ordering of carbon structure and internal microstructure of granular coke before and after microwave pretreatment was carried out. It is shown in X-ray diffraction results that the diffraction intensity of the coke sample significantly increased after 40 s irradiation under 264 W microwave power, which indicated the decrease in reactivity of coke.

Mar 1, 2017

By Craig Naudé

"An enhanced gravity concentrator was installed in conjunction with an Intensive Leach Reactor at the Sadiola plant in Mali last year and commissioned in Dec 2007.There has been much debate over the years as to the effect of gravity concentration on overall plant performance. The late Dr Laplante suggested that for every 10% of gold recovered by gravity, there was a corresponding 0.1% to 1% additional overall plant recovery. The results at Sadiola are consistent with this hypothesis with an overall 4% gain in plant recovery.With total gold recovery of 12% in the gravity section, grades are increased from 3.54g/t in the gravity feed to an average of 2 600g/t in the concentrator feed to the in-line reactor. The recovery of gold in the in-line reactor is in excess of 98.5%.This paper discusses the background to the project, the laboratory testwork prior to the equipment selection, the operational results of the system, as well as the benefits of the future application of high mass yield centrifugal concentrators in base metals, sulphides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.INTRODUCTIONBesides picking nuggets off the ground or out of riverbeds, gravity concentration is arguably one of the oldest methods of recovering gold. In circa 6000BC people discovered that gold can be found behind the rocks and in depressions of creek beds. By placing rocks in a stretch of channel with the proper slope the first sluice is built, probably around 4,000 BC, and this method is still practiced today."

Jan 1, 2009

By S. Saha

Minerals in coals cause operational problems in various coal utilization technology as well as act as diluents towards its heat value. Indian coals contain higher percentage of mineral matter compared to foreign coals due to its formation through drift origin. Efficient utilization of high ash coal in environment friendly manner is the driving force for the development of clean coal technology. Coal gasification offers practical means meeting stringent environment controlled parameters for producing power, chemicals, liquid fuels and clean energy on a single platform. It is well accepted that gasification technology has sufficient potential for sustainable development of clean coal technology. Gasification reactivity depends on the coal properties and operational parameters as well as minerals present in coal. Minerals not only create operational problems but on the other side also catalyze the gasification and combustion reaction. Therefore to understand the effect of minerals on the gasification reactivity, present paper proposes to study the variation of gasification reactivity with various gravity cuts such as, 1.4-1.5; 1.6-1.7; and 1.8-1.9 of a selected coal. Gasification reactivity has been studied by thermo gravimetric analyzer (TGA) using CO2 as gasifying agent. Surface properties such as, true density, apparent density, porosity, surface area of different gravity cut samples have also been measured to find out the effect of gravity separation on gasification reactivity. Keywords: gasification, reactivity, mineral matter, gravity separation

Sep 1, 2012

Effect of Grinding Media on the Flotation of Sulfide Minerals

Sep 13, 2010

By H. Ipek

Industrial grinding machines used in the mineral processing industries are mostly of the tumbling mill type. These mills exist in various types: ball, rod, pebble, autogenous, and semi-autogenous. Balls and rods are traditionally media shapes used in the tumbling mills. In resent years, as an alternative to balls, grinding charges with various shapes are being used. Cylpebs are slightly tapered cylindrical grinding charges with length equaling diameter, and all the edges being radiused. Cylpebs of equal diameter and length have 50% greater surface area and 45% greater weight than balls of the same material. In addition, they have 9% higher bulk density than steel balls, or 12% higher bulk density than cast balls. An important advantage of cylpebs over balls is that cylpebs produce narrower granulometric distribution due to their shapes. However, some discrepancies were found in the literature regarding the milling performance of cylpebs in comparison with balls (Chi, 2004). In recent studies, Chi (2004) has provided detailed information on cylpebs and has compared these to balls in relation to media mass, size distribution, surface area, and input specific energy. Ipek (2006) has investigated the effects of cylpebs and balls with equal mass and surface area on the breakage rate of quartz, using cylpebs and balls separately. Similarly, Lameck and Moys (2006) have investigated the effects of balls and worn balls on breakage rate of material using worn balls as grinding environment. However, no study has attempted to investigate the effects of grinding environment other than balls on the brekage distribution. As indicated by Prasher (1987), the breakage distribution function is independent of the following variables in ball mills: hold-up (Mika et al., 1967; Kelsall et al. 1969), mill speed and ball load (Herbst and Fuerstenau, 1972), media load and ball density (Kelsall et al., 1973), mill diameter (Malghan and Fuerstenau, 1976), and powder charge (Shoji et al. 1980). The aim of the present paper is to compare the effects of cylpebs and balls on the breakage distribution function of quartz with respect to same mass and same surface area. BACKGROUND Comminution as a rate process is called kinetic approach. Studies on the kinetic approach are reviewed by Oner (2001). Oner states that grinding kinetics are based on studies by Kolmogorov in 1941 and that Robert (1950) is the first to suggest this approach. Later, Melzak, Loeveday, and Reid have improved the grinding kinetics equation; and, Austin and Lynch have conducted two basic studies on the analytical solutions of these equations. Considering the results of studies comparing the size reduction mechanisms, it has been accepted that breakage constitutes of two operations. These two basic operations, first defined by Epstein (1948), are those of selection of material for breakage and the distribution of breakage material to particle sizes smaller than the initial size (Lynch, 1977). Epstein defined the two operations as: ? Pn(y), the probability of breakage of a particle size in the nth step of the breakage process. ? F(x,y), the cumulative distributions by weight of particles of size x<y arising from the breakage of a unit mass of a size y. Probability of breakage is called a selection or a breakage-rate function (Si). Characteristics size distribution after breakage is called a breakage distribution or appearance function (Bi,j). Due to the difficulties in representing particle size distributions mathematically and constantly, the batch equation based on particle size fraction is suggested. Thus, as is the case in breakage distribution and specific rate of breakage, the breakage parameters were defined by batch grinding experiments conducted in laboratories (Oner, 2001). When effective breakage occurs in the mill, the breakage of material with single feed size fraction usually fits first order grinding kinetics and the specific rate of breakage values can be calculated through the slope of semi-log plot. The values of the breakage distributions are deduced from the size distributions at short grinding times where there is mainly size 1 material breaking and only small amount of smaller sizes to rebreak (Austin et. al., 1984). B values can be calculated by using BII. [ ] where j is the top size of the charge, Pi(t) is the cumulative percent undersize of i th size interval at the short grinding time which gives no more than about 30% broken out of the top size interval. Cumulative primary breakage distribution, Bi,j, is also defined in an empirical form by [ ] where xi is the top size and Bi,j is the weight fraction of primary breakage products. The parameters F, ? and ß define the size distribution of the material being ground. On plotting size versus Bi,j on log scale, the slope of the lower portion of the curve gives the value of ?, the slope of the upper portion of the curve gives the value of ß, and F is the intercept as in Fig.1. [ ]

Jan 1, 2009

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By Bern Klein, Randy Blaskovich, Reem Roufail

"Morphology is a tool that is rarely used for mineral breakage mechanism evaluation. Ground particles are typically assessed for their size distribution. They are also visually analyzed using image analysis. However, image analysis is not a comprehensive evaluation of the particle surface texture. It evaluates particle’s size parameters such as area, diameter, and perimeter amongst other features. On the other hand, morphology analysis takes the particle assessment to another level of detail. Morphology analysis evaluates particles’ roundness, elongation and angularity that would indicate the degree of roughness of the particle. According to Roufail and Klein (2009), rougher surfaces are generated due to breakage along grain boundaries – intergranular breakage. Mill operation, particularly mill speed, dictates the dynamics in the mill. Stirred mills are known to break the particles via abrasion under standard operation. However, if the dynamics of the grinding media in the mill are changed, the particles could be more exposed to impact and compression loading that would lead to a different mode of breakage.In this paper, the effect of material properties and mill operating conditions on particle morphology will be studied. Hard non-sulfide versus soft sulfide minerals are compared, namely quartz and galena, respectively. Extreme mill speeds are tested covering the range of 1000 to 2000 rpm for a 4-litre Netzsch (ISA) mill. In addition to particle size distribution, micro-analysis is executed in the form of morphological analysis using a tested manual roughness point counting technique.INTRODUCTIONGrinding in general and stirred milling in particular are processes that are used to break particles to liberate metal-bearing minerals for further separation downstream. The energy required to achieve the target particle size versus maximum possible liberation has been studied intensively and it is usually the breaking point for the grinding system chosen in a process flowsheet. Operating conditions are dictated by the energy consumption. Becker et al. (2001) related different forms of energy such as input, specific, volume/mass specific energies to stress intensities and final product fineness. Other research studies focused on energy input in a stirred mill (Zheng, Harris and Somasundaran, 1996)."

Jan 1, 2011

By R. K. Rath

Adsorption, electrokinetic and flotation studies were carried out. The maximum density of adsorption of guar gum was obtained at pH 7.5 on sphalerite and at pH 11.5 on galena. Flotation recovery of sphalerite was reduced only marginally by the presence of guar gum in the pH range investigated, whereas recovery of galena was reduced to about 20% at pH 12. Differential flotation tests on binary mixtures indicated that 10 ppm of guar gum can depress galena and separate it from sphalerite at around pH 12.1. Co-precipitation tests confirmed the formation of a metal ion-guar gum complex in the bulk solution, suggesting that this is the precursor to adsorption. The adsorption isotherms for both minerals followed Langmuirian behaviour, but adsorption of guar gum on galena was significantly higher than on sphalerite and dissolution tests indicated that the concentration of Pb ions released from galena was an order of magnitude greater than that of Zn ions dissolved from sphalerite

Jun 21, 1905

By Francis S. Kendorski

High-extraction mining of coal and other stratified minerals has a predictable effect on the surface and subsurface. Impacts on ground waters in overlying strata and on surface waters, that are associated with overlying sequential zones of collapse, fracturing, aquiclude, constrained strata, and surface disturbances can be anticipated. Since first quantified around 1979 in Bureau of Mines sponsored contract research work and others (and often adopted by state regulators), with zone extents based upon multiples of mined seam height of 24 to over 60 for the fractured zone, much new data have become available. In examining the sources of data and the methods and intents of the researchers of over 65 case histories, it became apparent that the strata behaviors were being confused with overlapping vertical extents reported for the fractured zones and aquiclude zones depending on whether the researcher was interested in water intrusion into the mine or in water loss from surface or ground waters. These more recent data, and critical examination of existing data, have led to the realization that the former "Aquiclude Zone" defined for its ability to prevent or minimize the intrusion of ground or surface waters into mines has another important character in increasing storage of surface and shallow ground waters in response to mining with no permanent loss of waters. This zone is here named the "Dilated Zone." The existence of the dilated zone explains the ratios of up to 60 times the mined thickness. Surface and ground waters can drain into this zone, but seldom into the mine, and can eventually be recovered through closing of dilations by mine subsidence progression away from the area, or filling of the additional void space created, or both. A revised model has been developed which accommodates the available data, by modifying the zones as follows: ? collapse and disaggregation extending 6 to 10 times the mined thickness above the panel ? continuous fracturing extending approximately 24 times the mined thickness above the panel, allowing temporary drainage of intersected surface and ground waters ? development of a zone of dilated, increased storativity, and leaky strata with little enhanced vertical permeability from 24 to 60 times the mined thickness above the panel above the continuous fracturing zone, and below the constrained or surface effects zones, whose thickness or existence is dictated by the zones above and below ? maintenance of a constrained but leaky zone above the dilated zone and below the surface effects zone, whose thickness or existence is dictated by the zones above and below ? limited surface fracturing in areas of extension extending up to 50 ft or so beneath the ground surface

Jan 1, 1993

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

Blaine number has long been used to evaluate the pelletising ability of iron concentrate in the industry. Much information and practical data are available about the effect of Blaine number on pelletising efficiency of different concentrate types. But not many researchers have focused on the effect of Blaine increasing method on pelletising behaviour of coarse concentrates. In this paper the effect of two different grinding methods (i.e. HPGR and Ball Mill) on physicochemical properties of coarse magnetic concentrate green and fired pellets were investigated. Microstructural studies by Field Emission Scanning Electron Microscope (FESEM) showed that the concentrate for which the Blaine number had been increased through HPGR grinding, has flake-like morphology. In contrast, increasing the Blaine number through ball mill grinding results in more granular particles. Two samples were prepared using HPGR and ball mill. The Blaine number of the HPGR product and ball mill product were 900 cm2.gr-1 and 1200 cm2.gr-1 respectively. The results revealed that pellet properties of this HPGR product are comparable to that of the ball mill product; this is due to the fact that the flake-like morphology leads to enhanced pelletising performance of coarse magnetite concentrates. Keywords: Iron pelletising, Blaine number, HPGR, ball mill, coarse particles

Jan 1, 2020

By S. Veeramasuneni, C. D. Dunbar

The rate of hydration influences many important physical properties of gypsum. Previous research examined the rate of gypsum hydration and related this to compressive strength and microstructure development using BET specific surface area analysis. The analysis of gypsum porosity in combination with BET surface area and rate of hydration remains to be done. In the present study, mesoporosity is analyzed using the numerical method of Barrett, Joyner and Halenda (BJH) to gain a greater understanding of gypsum hydration and microstructure development. The rate of hydration has a significant effect on mesoporosity of the gypsum matrix. The results reveal the effect of mesoporosity and hydration rate on some macro physical properties of gypsum.

Jan 1, 2000

Effect of Hydrophobicity and Frother Concentration on Bubble-Particle Interactions in Turbulent Flow

Sep 13, 2010

By Paul Worsey, Yasutaka Dote

The choreography of large fireworks displays dictates electric initiation for precise timing. It has been common practice to pre-squib products before transportation for reducing set up time. A number of fatal accidents transferring pre-squibbed product during transportation suggests that there is a problem with impact sensitivity. The aim of this paper is to quantify the impact sensitivity of the various configurations of initiating materials used in display fireworks.

Jan 1, 2009

By S. K. Chan, C. Badeen, S. Goldthorp, H. Feng, I. Alilovic, R. Turcotte

Over the last few decades, water-based explosives and their precursors, despite their apparent insensitivity, have been involved in a number of accidents around the world. A large proportion of these accidents occurred when these emulsions were pumped either for their manufacture, transport, or handling. In Canada, this has led to the development of “Guidelines for the Pumping of Water-Based Explosive”, which state that “using pumping pressures well below the laboratory measured minimum burning pressure (MBP) of the corresponding emulsions or watergels is a good safety practice”. However, in the above document, there is no description on how the MBP should be measured. In the last few years, a research program at the Canadian Explosives Research Laboratory (CERL) in collaboration with Orica has been focused on the development of a validated measurement protocol for realistic MBP measurements.

Jan 1, 2014

By Y. I. Yang, Y. -B. Tang, D. -J. Ma

Chlorine-containing minerals are commonly present in coal. Associated minerals such as pyrite can undergo exothermic reactions. Consequently, it is of great significance to study the effect of inorganic chloride on the spontaneous combustion of coal. In this study, the effects of five inorganic chlorides (sodium chloride, magnesium chloride, potassium chloride, calcium chloride, and zinc chloride) on the spontaneous oxidation of coal were investigated. Analysis of the gaseous products of coal oxidization at low temperatures (323K to 453K) showed that the presence of inorganic chlorine in coal markedly decreases O2 consumption and the generation of CO and CO2. Samples of raw coal and chlorine-loaded coal were oxidized for 36 hours under the same experimental conditions. Infrared diffuse reflectance spectroscopy results showed that inorganic chloride can inhibit the oxidative decomposition of some functional structure components (methyl, methylene, methine, and hydroxy) in the coal. The influence of inorganic chloride on the oxidation characteristics of the functional groups in coal during spontaneous combustion was investigated using benzyl alcohol and 1-phenylpropanol as model compounds, which were tested under the same experimental conditions as the coal samples. The oxygen consumption of model compounds with and without the addition of inorganic chloride further suggested that inorganic chloride may hinder the oxygenolysis of these structures during low-temperature oxidation. This phenomenon can be attributed to the radical reaction from the perspective of radical chemistry. It can therefore be concluded that inorganic chlorides play an inhibitory role in the spontaneous combustion of coal.

Jan 1, 2015

By Ali Porbaha

Rapid growth in the urban development requires continuous search for innovative technologies to construct complex infrastructure systems. Deep mixing is one promising construction technology that has a wide spectrum of applications for development and expansion of complex urban facilities. Large number of reported case history of the projects in Europe, Japan, and the US demonstrate the versatility of the technology compared to conventional methods of ground modification. A large number of factors influence the quality of the soil cement columns; some of these are rooted in the installation process and the effective use of machinery during construction. This paper attempts to present some issues related to installation of deep mixing that affect quality of the treated columns. Presented here are various installation patterns, installation machinery, installation sequence, effect of penetration/withdrawal injection methods, penetration/withdrawal speed, effect of number of shafts, rotation of the blade, shape and orientation of mixing tools, and rotational speed of the shaft on quality of the treated ground.

Jan 1, 2001

Over the past seven years a large database of coal self-heating rates under adiabatic conditions has been developed at The University of Queensland. Coals have been tested from Australia (Queensland and New South Wales), New Zealand (North and South Island), Indonesia and more recently the United States. As a result of this work, definitive relationships and trends have been established for the effects of various intrinsic coal properties on self-heating rates and anomalous coals have also been identified. Previously held views on the effects of coal rank, type and inorganic constituents are examined in this paper. Many of the published relationships do not hold true in terms of coal self-heating rates. A propensity rating scheme has also been developed which is routinely used in Australia for assessing coals and identifying appropriate mining analogues for spontaneous combustion management planning. A selection of examples will be presented in the paper, which shows the significance of this assessment strategy.

Jan 1, 2009

By Woodcock J. T, Zhu T, Sparrow G. J

A lead-zinc-pyrite flotation middling was pressure oxidised to give residues containing iron hydroxy sulphates (a mixture of basic iron sulphate (BIS) and a hydrated iron sulphate (HIS)) and lead sulphate. Direct thiourea leaching of this residue gave over 90 per cent extraction of gold and silver, but thiourea consumption was high (56 kg/t) because of soluble iron(M) in the residue. Attempts were made to decrease the thiourea consumption by removing the water-soluble iron(M) or reducing it to iron(II). Water washing of the pressure oxidation residue removed most of the hydrated iron sulphate but little of the basic iron sulphate. Iron removal was only 12-20 per cent, depending on the number of washes, from one sample which was low in HIS, and 40-45 per cent in another which was high in HIS. Iron extraction was not appreciably increased by using dilute sulphuric acid (with or without additions of sodium sulphite), dilute phosphoric acid, or sodium chloride solution (150 g/L NaCI). Direct thiourea leaching of the water-washed residue gave over 90 per cent extraction of gold but only 49 per cent of silver, with a thiourea consumption of 27 kg/t. However, the application of a water wash followed by reduction of dissolved iron(III) with sodium sulphite in the presence of thiourea, and then thiourea leaching resulted in over 98 per cent extraction of gold and silver for a thiourea consumption of 26 kg/t.

Jan 1, 1991

By R. M. Cooper, H. K. Herbert, D. N. Phillips

A study was carried out to determine the effects of adding CaCO3, Fe, Al and CaSi2 to the ladle, rather than to the raw materials, in order to increase the concentration of Ca, Fe and Al in the final product to meet customer specifications at Simcoa's Kemerton plant in Western Australia. LA-ICP-MS, SEM-EDXRA and ICP-AES analysis of samples and controls showed that the technique is suitable for controlling minor element concentrations. Iron was successfully added, while calcium silicide with aluminium proved better than limestone with aluminium for controlling Ca and Al concentrations in the silicon

Jun 19, 1905

Effect of Lattice Impurities on Electronic Properties and Surface Adsorption of Sphalerite - A Density-Functional Theory Study

Sep 13, 2010