Search Documents

By R. P. Vinson

Assessment of workplace exposures is an important tool for helping to minimize dust-related occupational illness and diseases. Real-time particulate monitoring can effectively locate areas where dust controls are needed and determine how well they are working. An affordable, person-wearable, real-time dust monitor is needed. The SKC Inc. Dust Detective (SKCDD) fulfills those requirements (Disclaimer: Mention of any company or product does not imply endorsement by NIOSH). The SKCDD consists of a disposable sampling tube (DST) connected to a small hand-held sampling pump. The SKCDD was developed through a Cooperative Research and Development Agreement (CRADA) between the National Institute of Occupational Safety and Health (NIOSH) and SKC Inc. The relationship of dust concentrations measured by personal gravimetric samplers to those measured by the SKCDD was determined in a laboratory aerosol chamber. A comparison of the means and the relative standard deviation of triplicate measurements of each type of sampling device demonstrated the SKCDD to be a viable alternative means for measuring dust. While it provides accurate measurements for specific coal types, it requires correction factors (those correction factors still need to be calculated) for other coal types.

By I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke, and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale Fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL) in Fairchance, PA, using Ponderosa Pine, Red Oak, Douglas-fir, high and low volatile coals, PVC and SBR conveyor belt, No. 2 diesel fuel, and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector, and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations, and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (1). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters? Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2012

By C. D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due both to nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustion. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines. Subsequent to these laboratory experiments, six smoke detectors were installed in an underground limestone mine for further testing and evaluation. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By P. Venter, N. Naude

"Coal mining is a thriving industry and 53% of the coal mined in South Africa is used for electricity generation. Mechanization has made coal mining more efficient, but fines generation has subsequently increased. Up to 6% of the run of mine material can report to the -200 µm fraction. Common problems associated with fines handling include dust formation, storage problems, and high moisture levels. A method to turn this material into a saleable product instead of stockpiling it can add value to a company.Briquetting is a pressure agglomeration method where loose material is compacted into a dense mass (FEECO International, 2014). The briquettes must be able to withstand rigorous handling and transport operations without disintegrating. This study aims to investigate the optimum binder and moisture conditions required to produce a mechanically strong briquette using two different binders - a PVA powder (binder A) and a starch powder (binder B).It was found that for binder A the optimum moisture level was 12% to 14%. At this moisture level the greatest compression strength gains were observed, and low amounts of fines produced in impact and abrasion tests. The minimum amount of binder added while still obtaining a strong briquette was 0.5% binder A. For binder B the optimum moisture level was also 12% and the minimum amount of Binder B to be added was found to be 1%. Briquettes that were dried outside reached their peak strength after about four days, whereas the briquettes that dried inside took about 20 days to reach their strength plateau. Hardly any degradation took place on the surface of the binder A film after exposure of 300 hours of artificial weathering. Thermogravimetric analysis confirmed that neither binder A nor binder B will add to the ash content of the coal fines, as both binders totally decompose above 530°C.Binder B yielded stronger briquettes after 15 days and also generated less fines. It is therefore superior to binder A and would be recommended for further use.Paper written on final year project work carried out in partial fulfilment of B.Eng degree in Coal Beneficiation"

Jan 1, 2015

By A. Fahimifar, H. Soroush

Abstract: In order to develop non-destructive methods in studying physical and mechanical properties of rock and replacing them with difficult and expensive static methods, several ultrasonic tests were carried out on cylindrical rock specimens in accordance with the ISRM suggested methods and velocity of P and S waves were determined. Also, density, porosity, water absorption, uniaxial compressive strength and indirect tensile strength were determined for each specimen in accordance with ISRM suggested methods. According to above tests static and dynamic elastic constants were calculated After statistical analysis of data obtained from tests, the relationships between velocity of elastic waves and physical or mechanical parameters were determined and some equations were obtained. Also similar analyses were performed on static and dynamic constants and some equations were extracted. Using these equations, the physical and mechanical parameters of rock and also static elastic constants can be estimated by conducting simple and quick tests (i.e. ultrasonic tests). Abriß: Um zu entwickeln, die zerstörungsfreien Methoden für Studieren die physischen und mechanischen Eigentümer von Steinen und auch ist für Ersetzen diese Methoden mit schwierigen teuren statischen Methoden, mehrere altrasonic Prüfungen auf zylindrischen Steinproben gemäß ISRM anregenden Methoden und den Geschwindigkeiten von S und P Wellen bestimmt worden sind durchgeführt worden. Außer der Dichtheit und der Porosität betonen Wasser Aufnahme und monoaxial Widerstand und dehnbaren indirekten Widerstand jeder Probe betreffend der erhaltenen Ergebnisse die atmosphärische Aufladung sind bestimmt worden und die dynamischen Faktoren der Steine sind kalkuliert worden. Nachdem statistische Analyse die Korrelation der Ergebnisse zwischen der Geschwindigkeit elastischer Wellen und mechanischer und physischer Eigentümer der Steine erhalten worden ist, und mehrere Verhältnisse sind vorgeschlagen worden. Eine ähnliche Analyse ist auf atmosphärischer Aufladung und dynamischen Faktoren durchgeführt worden und einige Verhältnisse sind erhalten worden. Mit Hilfe dieser Verhältnisse die physischen und mathematischen Eigentümer von Steinen und auch können die Statistik Faktoren durch einfachen und schnellen altrasonic Prüfungen erhalten werden. Resume: Puor le development des method non-destructive et evaluuation des propietes physical et mechanical des rock et superseding avec les methods dificzle et cher statique, c‘ est fait plusieur essayes ultrasonique sur les echantillons cylinrique et par a port le proposale TSRM et le vittesse des ondes P et S et densite et porosite et absorption des eaux le resistant de pression uniaxial et resistance de chaque echantillon est determinee. A la fin en base des resultat obtenue les constant statique et dynamique des roches sont calcule. Apres les analyses statistiquc sur les resultat obtenue du les essaybs, c‘ etait produit les relation entre les viptesse les ondes elastique et les proprietes physic et mechanicue des roches et c est propose quelque relations. Aussi le meme enterpretation sur les constant statique etdinamique. En possezon de ces relations, les spesificatio physique, aussi on peut trouver leur constant statique, avel les essayes sample et raptid a d ultrasonique.

Jan 1, 2003

By T. R. Roy

"This paper presents an objective model for the estimation of fire risk potential of an underground coal mine panel by the bord-and-pillar method of mining where extraction is carried out by depillaring with caving. The fire risk rating procedure for the estimation of fire risk potential involved in the panel is described in detail. The model developed thereof is tested with the field data collected from different collieries across the country along with the laboratory data for critical assessment of fitness of the model. Some results showing the validity of the model are also cited here. Introduction The occurrence of fire in underground coal mine panels is quite common in India and elsewhere. These fires cause extensive loss of resources.Although substantial work has already been done by different research organizations, the problem has not been fully eliminated.The causes of panel fires depend not only on the spontaneous heating susceptibility of coal, but also on the extraneous conditions created in the panel due to the mining operations. From the studies done so far by various organizations, it is apparent that two types of parameters associated with spontaneous heating of a coal mine panel exist: intrinsic and extrinsic. Parameters related to the nature of coal, i.e., its physicochemical characteristics, petrographic distribution and mineral make-up are intrinsic, while the extrinsic parameters are related to the atmospheric, geological and mining conditions such as scope of leakage of air into the panel, wetness of mines, heat dissipation capacity of the panel, gassiness of seam, geological disturbances, method of extraction, size of panel, etc.Banerjee (1982) identified twenty-two mine parameters such as spontaneous heating susceptibility of coal, method of mining, geological disturbances, quality of overburden, degree of consolidation of coal mass, scope of accumulation of coal fines, etc. that can influence spontaneous heating in underground mines. He used the terms “high” and “low” for fire risk rating of each of these parameters. Since this approach is oversimplified, it can not determine the exact fire risk potential of an underground working."

Jan 1, 2003

By B. Gazea, A. Kontopoulos, A. Kourtis, K. Adam

Static tests give a measure of the balance between acid-producing and acid-neutralising mineral components in a material, while kinetic tests determine acid generation and neutralisation over a long period. Drill-core samples from the amphibolite and gneiss host rocks of the Stratoni lead-zinc sulphide deposit in Greece and mine/mill waste samples from Stratoni and Olympias were examined by the standard acid base accounting, BCR and net acid production tests. Mineralogical data on the materials and resulting residues were used to illustrate the differences between the methods and establish their ranges of applicability. BCR seems to simulate most closely the conditions prevailing during generation of acid mine drainage but is time-consuming and requires elaborate equipment. Acid base accounting is suggested for standard screening; net acid production might be used in the field or for solids with less than 10% S

Jun 19, 1905

By Scott Thayer, Michael Murphy, Natalie Cope, Gabriel Esterhuizen, Anthony Iannacchione, Tim Miller, Brent Slaker

"The Subtropolis room-and-pillar mine extracts the Vanport Limestone (Allegheny Formation, Pennsylvanian System) near Petersburg, Ohio. Strata instability problems associated with excessive concentrations of lateral stress caused the mine operator to implement a change in layout design. This mining method has been identified as a stress control layout, which has been used by other underground stone mines in the past with varying degrees of success. Practical experience has shown that entry headings advance in the direction of the principal lateral stress, producing lower stress concentrations with better mining conditions. It is important to minimize stress concentrations along the mining front, so an arrow-shaped advance is recommended. This technique advances more developments (headings) in a “good” direction and reduces developments (crosscuts) in a “bad” direction. As is expected, the stress control layout enhances the potential for shear failures in crosscuts. It is, therefore, important to focus crosscut engineering interventions that either: (a) lower stress concentrations (for example, an arched roof) or (b) enhance strength of the strata containing the shears (for example, rock reinforcement). This study focuses on observing strata conditions on a regular basis and monitoring the response of this strata to changing geologic and mining conditions through 3D Dynamic LiDAR scans.INTRODUCTIONProject AimsThe Subtropolis Mine is extracting the Vanport Limestone in northeastern Ohio. Since the start of mining in 2006, ground conditions have been significantly affected by excessive lateral stress condition. In some other mining districts with this hazard, certain mine layouts have been shown to lessen the potential for unstable ground conditions. The term “lessen” is used to state the realization that stress concentrations are not eliminated but instead occur in less frequency and intensity, and their locations can be projected.The stress-control mine layout, specifically for large-opening room-and-pillar stone mines, naturally evolved at mines suffering from excessive lateral stress problems. These mines will typically experiment with methods to mitigate adverse impacts, thus developing best practices for their conditions. These practices have evolved into a basic framework for the stress control mine layout. For example, Jack Parker was able to write about personal experiences at the White Pine Mine in Michigan (Parker, 1966, 1973). Various researchers at the U.S. Bureau of Mines (USBM), the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and Health (NIOSH) have studied the effectiveness of stress-control mine layouts over a wide range of geologic conditions (Emery, 1964; Mark and Mucho, 1994; Iannacchione et al., 2003). While the stress control layout design approach has proven successful in many categories, it can be difficult to implement. For example, excessive stress conditions in crosscuts can put the ground control focused intervention at odds with ventilation and haulage constraints, thus limiting optimal crosscut size, shape, and location. Therefore, more information on the effectiveness of this approach is needed."

Jan 1, 2019

By M. Nehdi

Deficient surface disposal systems of sulfidic mine waste often cause severe contamination of surface streams and groundwater reservoirs due to the oxidation of sulfide phases. The subsequent generation of leachates characterized by high acidity and elevated concentrations of toxic elements (commonly known as acid mine drainage) jeopardize the health of contiguous ecosystem. Stabilization/solidification (S/S) is recognized as a promising solution for treating such wastes. S/S processes generally mobilize alkaline and/or cementing materials/additives that act as neutralizing and/or binding agents. In the present research, industrial byproducts, namely, cement kiln dust (CKD) and Class C fly ash (FAC) have been used as candidate materials along with the partial addition of sulfate-resistant cement (SRC) in the S/S of polymetallic sulfidic mine tailings (MT). The effectiveness of S/S was assessed by comparing laboratory experimental values obtained from unconfined compressive strength, hydraulic conductivity and leaching propensity tests of S/S samples with regulatory standards for safe surface disposal of such wastes. Despite general regulatory compliance of compressive strength and hydraulic conductivity, some solidified/stabilized-cured matrices were found unable to provide the required immobilization of pollutants. Solidified/stabilized and 90-day cured mine tailings specimens made with composite binders containing (10% CKD + 10% FAC), (5% SRC + 15% FAC) and (5% SRC + 5% CKD + 10% FAC) significantly impaired the solubility of all contaminants investigated and proved successful in fixing metals within the matrix, in addition to achieving adequate unconfined compressive strength and hydraulic conductivity values, thus satisfying U.S. EPA regulations. Laboratory investigations revealed that, for polymetallic mining waste, leachate concentrations are the most critical factor in assessing the effectiveness of S/S technology.

Jan 1, 2008

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid-bake leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400 ºC) sulfuric acid baking of an enargite concentrate followed by water-leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase for baking at 400 ºC. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400 ºC, sulfuric acid amount of 0.5 mL/g of concentrate, and 2 h baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). XRD analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in similar fashion.

Jan 1, 2012

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

Instabilities occurred as a result of climate changes caused to investigate the rock behavior dependency to temperature changes, in this paper. In the natural earth condition, the phase transition of pore water has known to be the most effective factor causing different rocks mechanical properties due to temperature changes. So, the temperature range of [-30, 30]°C is selected in laboratory tests of this study. P-wave velocity, unconfined compressive strength (UCS) and elasticity modulus of rocks at different temperatures are studied by developing a temperature adjusting apparatus. The tests were performed on three rock types. The results show that firstly, the temperature reduction and pore fluid freezing improves these rock?s mechanical properties. Secondly, the dependency of rock properties to climate changes depends on the type and shape of its porosity as well as porosity percent. The improvement of rock mechanical properties in jointed rocks exceeds rocks with spherical pores. Finally, maximum changes in rock?s properties occur at [-10, 0]°C, which includes the phase transition of pore fluid. Keywords: Temperature; Rock Mechanical Properties; Pore Fluid; Porosity.

Feb 27, 2013

By J. Engels

CODELCO is considering the implementation of high-density tailings management at the Chuquicamata mine in northern Chile for its long term disposal plan. To achieve this, CODELCO commissioned the design, construction, and operation of a 70 t/d pilot plant, fed by existing tailings. The testing programme was completed in May 2011, and consisted of laboratory rheological and characterization assessments, pipe loop testing, beaching trials, and analyses of deposition behaviour for solid contents ranging from 57?68% (w/w). This paper describes the characteristics of the pilot plant, the testing programme, the beach trial analyses, and the resulting beach profile predictions based on the stream power theory. CODELCO also used other predictive beach slope methods, such as the equilibrium slope concept, which are not discussed in this paper. The final beach profile for design will be selected after an expert analysis of all methods has been completed.

Jan 1, 2012

By Michael S. Contratto, Dave Marshall, Tom Brodersen

The European Union (EU) completed a new directive 2002/44/EC1 called the Physical Agents Directive (PAD) that establishes action and limit values for hand-arm and whole body vibrations. The directive specifies that: “…workers shall not be exposed above the exposure ‘limit value’.” 1 and “…once the exposure action values … are exceeded, the employer shall establish and implement a programme of technical and/or organisational measures intended to reduce to a minimum exposure to mechanical vibration and the attendant risks…” 1 The PAD limit value is effective for new machines starting July 6, 2007 and for used machines by at least July 6, 2010. These requirements apply to the users of machines, but machine manufacturers will be challenged to provide machines and information to help the users comply with the directive. Caterpillar manufactures machines with the goal of enabling our customers to comply with all regulations dealing with health and safety. Caterpillar designs all of our machines to provide a safe, comfortable and productive work environment. This study was to determine if seat suspensions could provide a reduction in the vibration environment experienced by operators of Caterpillar mid sized (<50,000KG) Track Type Tractors Methods Seat manufacturers were asked to provide seat suspensions that provide improved isolation over and above current seat suspension. Each supplier was provided with ride profiles and was asked to demonstrate the vibration reduction on a shaker table. Two suppliers provided suspensions that were compared with the current seat suspension in a field study. Three full factorial experiments were conducted. The first experiment was to evaluate overall suspension performance for four operations. The second experiment was to determine the benefit of the adjustable vertical damper at three different levels and the third experiment was to determine the effect of the fore/aft and side/side isolators. Six operators were used for the study. Acceleration was measured at the seat base and at the operator seat pad. Both the transfer function and the ISO 2631 RMS ride values were used to determine the seat suspension’s effectiveness of isolating the operator from vibration. A structured questionnaire was used to determine the operators’ subjective assessment of the seat suspensions. Results There was significant operator-to-operator variability in the vertical direction (>35%), however there was little variability in the fore/aft and side/side direction based on seat base

Jan 6, 2006

By J. H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) amended the Federal Mine Safety and Health Act of 1977 to improve the safety of mines. The MINER Act established a Technical Study Panel (the Panel) to provide independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant materials in underground coal mining (1). Because frictional heating is a common cause of belt fires, the Panel recommended that the Mine Safety and Health Administration (MSHA) evaluate the drum friction test to determine if such a test would contribute to conveyor belt safety beyond that provided by the Belt Evaluation Laboratory Test (BELT). This paper compares the results of the drum friction test to results from the BELT and large-scale tests for six different conveyor belts. The results are used to evaluate the drum friction test as a method to determine the fire resistance of conveyor belts.

Jan 1, 2011

By S. Khoshjavan

In this investigation, the effects of different coal chemical properties were studied to estimate the coal Hardgrove Grindability Index (HGI) values index. An artificial neural network (ANN) method for 300 data-sets was used for evaluating the HGI values. Ten input parameters were used, and the outputs of the models were compared in order to select the best model for this study. A threelayer ANN was found to be optimum with architecture of five neurons in each of the first and second hidden layers, and one neuron in the output layer. The correlation coefficients (R2) for the training and test data were 0.962 and 0.82 respectively. Sensitivity analysis showed that volatile material, carbon, hydrogen, Btu, nitrogen, and fixed carbon (all on a dry basis) have the greatest effect on HGI, and moisture, oxygen (dry), ash (dry), and total sulphur (dry) the least effect. Keywords coal chemical properties, Hardgrove Grindability Index, artificial neural network, back-propagation neural network.

Jun 1, 2013

By Dennis Dolinar

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

Jan 1, 2007

By C. Doucet

Since 2001, CANMET Mining and Mineral Sciences Laboratories (MMSL) have worked with Falconbridge Ltd. (now Xstrata Nickel) to evaluate trends in the strength development and water retention properties of a novel backfill material for underground mining, called gelfill. Between 2004 and 2006, extensive laboratory tests were undertaken under the leadership of the Deep Mining Research Consortium (DMRC). This paper compares results obtained from samples circulated through a mini-flow loop and a simple mixer. Although many parameters were studied over the last five (5) years, this paper focuses on the investigation of the effect of the mixing method, sequence and time, and the curing environment on strength development and water retention of gelfill. It was found that binder should be added as a powder to the mix in the mini-flow loop, and that mixing slurry in the mini-flow loop as opposed to the mixer generally yielded higher strengths. The practical implications of these observations are the subject of an on-going underground trial that will compare laboratory and in situ properties of regular slurry fill with gelfill.

May 1, 2007