Search Documents

By M. E. Alam

In the present study, 1.1 volume percent of nano size copper was incorporated into pure tin using hybrid microwave sintering assisted powder metallurgy route. Microwave sintered samples were extruded both at room temperature and at 230 °C. Microstructural characterization studies were conducted on the extruded samples to investigate the distribution characteristics of secondary phase and grain morphology. Room temperature tensile test results revealed that hot extruded Sn-Cu samples exhibited higher strengths (~ 41%, in case of 0.2% yield strength and ~ 38%, in case of ultimate tensile strength) and ductility (~ 15%) when compared to room temperature extruded samples. On the contrary, the tensile properties of pure tin remained independent of extrusion temperature. An attempt is made in this study to correlate the effect of extrusion temperature on the microstructural evolution and tensile properties of Sn-Cu solder.

Jan 1, 2009

By P. Zhang

The use of phosphate depressants in the cationic flotation of silica from francolite in the Florida phosphate industry is rarely practiced. The occasional use of gelatinized starch derivatives and pH adjustments to assure a slightly alkaline flotation feed slurry pH have been used in some processing plants to improve selectivity. This paper presents a preliminary laboratory comparison of several potential phosphate depressants for use with the flotation of siliceous phosphates. It was found that starch is ideal for floating fine (-35 mesh) silica from phosphate, while sodium tripolyphosphate may be the best for coarser (+35 mesh) feeds.

Jan 1, 2009

Steady increases in longwall production have required operators to apply greater quantities of ventilating air in an effort to control and dilute respirable dust. Significant increases in shearer speeds necessitate that longwall supports also be advanced at a faster rate. Both of these factors may contribute to overall respirable dust levels on the longwall face because as supports are lowered and advanced, broken material falling from the top of the canopy is entrained directly into the air stream. To address this issue, the Pittsburgh Research Laboratory collected respirable dust samples from four longwall faces to characterize shield-generated dust. This paper investigates the influence of air velocity and shield advance rates on respirable dust levels. Also discussed are engineering controls currently used to reduce shield dust and alternative controls being investigated by the National Institute for Occupational Safety and Health (NIOSH).

Jan 1, 2009

By H. H. Murray

Significant changes in ownership and production of industrial clays have occurred since 2000. Clays covered in this presentation are kaolins, ball clays, smectites, (bentonite), and palygorskite (attapulgite)-sepiolite. IMERYS discontinued production of paper coating kaolins at their Cornwall operations and have expanded their kaolin production in Brazil. J. M. Huber sold their kaolin operation in Georgia to KaMin whose headquarters are in Ft. Worth, Texas. BASF purchased Engelhard?s kaolin and attapulgite operations in Georgia. ActiveMinerals purchased Southeastern Kaolin in South Carolina, Wilkinson County Kaolin in Gordon, Georgia, and Zemex Attapulgite in Quincy, Florida. Chemical Lime purchased Spinks Ball Clay Company in Paris, Tennessee. Most of the ball clays used in Italy and Eastern Europe comes from expanded operations in the Ukraine. Bentonite operations have expanded production in Wyoming and Montana because of strong demand for drilling mud, foundries, cat litter, and iron ore pelletizing. The production and exports of palygorskite in China continues to increase. Nanoclays utilizing sodium montmorillonite, palygorskite, and halloysite are actively being developed.

Jan 1, 2009

By Elizabeth M. Smith

The kcICON design-build project in Kansas City, Missouri includes widening the existing roadway, improving interchanges and grade separation bridges, and replacing the Missouri River Bridge. The Missouri Department of Transportation (MoDOT) typically utilizes steel H-piles and steel pipe piles as driven pile support for bridges. After bidding the kcICON project, the cost of steel rose significantly and the design-build contractor used an innovative approach to reduce foundation costs without significantly affecting the project schedule. The kcICON team conducted a value engineering evaluation of alternative foundation types for use at four grade separation structures. The result of the value engineering evaluation was selection of precast, pre-stressed concrete (PPC) piles as the preferred foundation alternative. Terracon developed a test program to evaluate the performance, capacity, and suitability of PPC piles at the site using a PDA and CAPWAP analyses. This paper presents the value engineering design, rationale for selection of PPC piles, results of the pile test program, and findings during production pile driving. The collaborative approach to the project by MoDOT and the kcICON team, combined with testing and a site-specific design approach, resulted in substantial savings for the design-build contractor.

Jan 1, 2009

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By Helge Rosenberg

Up to now, Topsøe WSA (Wet gas Sulphuric Acid) plants have been in operation for almost 30 years, and close to 80 plants have been sold. In spite of its unique features and ability to treat gases without any prior drying, the WSA technology has had certain restrictions with regards to SO2 concentration in the feed gas, and the overall conversion of SO2 by catalytic means has been limited to approx. 99.7%. In commercial scale sulphuric acid production on the basis of elemental sulphur and metallurgical off-gases, there is a demand for higher SO2 conversion and treatment of gases with a higher content of SO2. Therefore Topsoe has further developed its WSA technology to cope with these demands. This paper will explain more about the principles of such new development and leave the delegate with a better understanding of the potentials of the new generation of the WSA technology from Topsoe.

Jan 1, 2009

By D. Visser

This paper is based on the Townlands Ore Replacement Project whereby the concept of conventional sinking of one large diameter shaft was declined and replaced with three smaller raise bored shafts. A wire line geophysical survey was done and the results indicated that a single shaft larger then 4 m diameter unsupported would not be suitable. The shafts were placed 28 meters apart measured from centre to centre. To ensure that the skin to skin pillars between the shafts remained regular and to minimise any deflection, the pilot holes were drilled with the Rotary Vertical Drilling System. The different shaft sinking methodologies are discussed explaining the risk associated with each method.

Jan 1, 2009

By W. Vorster

Bateman Engineering Project's acid-plant track record goes back to 1977. Bateman Engineering can design sulphuric plants based on gas from sulphur burners, metallurgical off gas as well as pyrite roasting systems. Bateman Engineering has a technology marketing agreement with NORAM Engineering Ltd of Canada to provide state-of-the-art, well-proven acid plant technology, and also has access to roaster technology from several sources, including Chinese technology. Utilising the Noram technology agreement, Bateman was awarded the Engineering and Procurement (EP) contract for the Ambatovy Nickel Project, Sulphuric Acid Facilities in 2007. This is the first Greenfield sulphuric acid plant Bateman has designed for many years, producing a combined 5,500tpd, and is one of the largest sulphur burning acid plants in the world. This paper gives an overview of the sulphuric acid plant for the Ambatovy Nickel Project, advantages of Noram?s unique technology on offer, an overview of work conducted on a recent study of an pyrite roasting acid plants as well as a new technology currently being developed by Bateman for the direct combustion of solid sulphur to form sulphur dioxide.

Jan 1, 2009

By C. Guan

Since it was patented in 1942, the Crago process with fatty acid rougher flotation followed by deoiling and amine cleaner flotation has become the standard for phosphate flotation in Florida and North Carolina. This paper outlines the basic fundamentals involved in this proven technology. Included are the mineralogy of the flotation feed, the solution chemistry and the interfacial phenomena. The process variables affecting the performance of this technology are also discussed.

Jan 1, 2009

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By Michael Wieland

The resolving capacity of the thermodynamic work-principal model has been seriously refined over its twelve year history, so a review of the innovations, wrong turns and their rectification is warranted to help future researchers. The work-principal model rests upon the four laws of thermodynamics that drive the universe and relatively few other assumptions: like the removing and imposing of constraints on the quasi-potential to yield trapped minimum key-states that represent the wanted process. The formative research was concerned with the role of ingredient changes, the removal of booster influence and the quench temperature with which to reckon toxic fumes. The transfer of reaction-zone energy as work upon the surrounding rock/water/fixture was not fully rationalized until the notion of reversed-inertial pressure was formulated and determined (for water) with underwater trinitrotoluene (TNT) shots. The rock-water-jelly model incorporated that term into its dynamic pressure formula as a way to represent rock blasts or underwater shots, while the zone of reaction gases remained trapped. The real irreversible thermodynamic process, which yielded the total expansion work, was later complemented with a wholly reversible imaginary process, to form a closed thermodynamic loop, with a remarkable consequence – the determination of the theoretical heave and hence, the undissipated-shock by difference from the total work. With the wholly developed model, it was recently possible to quantify the time retardation of reaction chemistry for non-molecular (mining) explosives, as compared to the rather negligible time-retardation found for the molecular (military) explosives in underwater tests.

Jan 1, 2009

By Joshua Hoffman, Braden Lusk, Kyle Perry

This study explores how different geometries affect the shock tunnel’s performance and is broken down into three phases. Phase 1: Open arena testing in which theoretical energies produced by the detonation of small (<1.0 kg) charges are compared to actual experimental values. Phase 2: Shock Tunnel testing in which realized energies are experimentally recorded for the UK and S&T shock tunnels. Phase 3: Analysis of the data to begin building a pressure-forecasting tool for the UK shock tunnel given the explosive characteristics, sample size and desired pressure and impulse.

Jan 1, 2009

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009

[ ]

Jan 1, 2009

By H. Walqui

The Empire concentrator was built in four stages, with the latest stage accounting for 50% of the overall plant capacity. Over the past 5 years, the average throughput of the three grinding lines has decreased by 50 LTPH (15%) without significant changes in ore characteristics and despite the addition of secondary grinding capacity to supplement the existing pebble mills that are the constraint of the grinding circuit. This paper discusses the different areas under study that are aimed at optimizing grinding circuit utilization which includes improving system logic, pebble crushing operation and pebble mills operation.

Jan 1, 2009

By Raymond W. Henn

The 30th annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 22-26, 2009. The field demonstration portion of the course was conducted June 25, at Hayward Baker, Inc.?s yard in Broomfield, CO. The full-scale field demonstration annually presents many different types of drilling equipment being operated as well as various grouting methods being performed under different field conditions. As part of the field demonstration, the class is shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and measured conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results. The goal of the sand column demonstration is to show the students the effect of the water cement ratio and the use of admixture as well as the fineness of the cement, portland versus ultrafine, used has on the engineering properties of the grout and the grout?s vertical permeation through the sand. Test results for the demonstrations conducted in 1999 and for two separate demonstrations, one at the grout course and one at Geo Denver, conducted in 2000 were published in the 2001 proceedings of the Rapid Excavation and Tunneling Conference (RETC) (Henn et al. 2001). The test results for the 2002 and the 2003 demonstrations were published in the 2005 proceeding of the RETC (Henn et al. 2005).

Jan 1, 2009

By Aly M. Mohammad

The 12th and 14th Street Viaducts, which carry Route 139, are located west of the Holland Tunnel in Jersey City, New Jersey. The two viaducts, provide access to and from the Holland Tunnel (which connects New York City and New Jersey) and carry upwards of 50,0000 vehicles per day from Jersey City and New York City to points west. The New Jersey Department of Transportation (NJDOT) selected AECOM to perform design services including rehabilitation and seismic retrofit for the 12th Street and 14th Street Viaducts while maintaining traffic at all times. Building a new parallel bridge just north of the 14th Street Viaduct was essential in avoiding extremely costly traffic delays. Installation of the new foundation, in close proximity to the existing viaduct, required drilling through some of the existing timber piles supporting the bridge. As a result, the existing bridge was required to be reanalyzed for this new foundation configuration. This proposed structure consisted of 8 piers each supported on a single six (6) foot diameter drilled shaft. Currently this portion of the bridge structure has been constructed. The shafts were constructed with rock sockets that were five feet six inches (5?- 6??) in diameter and were extended 11.2 feet (3.4 meters) into rock. A 2300 ton Osterberg Load Test was performed on one production shaft to confirm the capacity of the shaft. The rock socket for the test shaft was in sandstone. This paper will present a description of the design methodology and construction methods adopted for the foundations. In addition, the paper will illustrate the Osterberg Load Test including: equipment used, number and locations of strain gages, and interpretation of results. Additionally, regarding the close proximity of the new foundation, the paper will present the type of equipment used to drill through the existing timber pile foundation while minimizing the impact on the integrity of the existing foundation. We will also present the method of analysis for analyzing the redistribution of load on the remaining piles. The results presented in this paper will assist the design engineer by providing a comparison between the geotechnical design assumptions and the actual measurements obtained by field measurements for this rock formation.

Jan 1, 2009

By F. Habashi

Brazil is a major mineral and metal producer, has magnificent fauna and flora, and superb architecture. In 1693 gold was discovered in Ouro Preto and Brazil produced about half of the world&apos;s gold. In 1726 diamond was discovered in the region of Tijuco in the Province of Minas Gerais, 150 km east of Bello Horizonte. The country became independence from Portugal in 1822 as the Brazilian Empire. In 1876, an Englishman succeeded in obtaining from the Amazon region seeds of rubber trees and secretly transferred them to England, where they were planted in the royal gardens at Kew. Some of the seedlings which spouted were sent to Ceylon and Singapore. Thus, began the rubber industry in the East. Today, Brazil is the largest producer of niobium, and produces a large number of other metals. The Mineral Research Center in Rio de Janeiro is the countries main Government establishment for mineral research. The country has been a republic since 1889 with its capital in Brazilia.

Jan 1, 2009