Search Documents

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By S. M. Moore

Technological advances in underground coal mining have reduced fatalities but may not have reduced worker exposure to cumulative injury risk factors. The objective of this study was to evaluate the prevalence of cumulative injuries before and after the implementation of technological advances in underground coal mining and to make a general cost estimate for these injuries. A previously published algorithm was utilized to identify cumulative injuries within the Mine Safety Health Administration (MSHA) database for two data sets: 1983-1984 and 2003-2004. For both, the following were determined: the number and percentage of cumulative injuries, the average days lost, the average age at the time of injury, the average years of experience and the general cost estimate by body part. The percentage of cumulative injuries remained largely unchanged (37 percent in the 1983-1984 period and 33 percent in the 2003-2004 period). The average number of lost days due to cumulative injuries increased (36±55 days and 62±82 days, respectively), which may have been due to the increased worker age (seven years older in the 2003-2004 period), increased length of employment (seven years longer in the 2003-2004 period) or other factors such as changes in medical practices. Cumulative injuries to the back decreased by 10 percent, while cumulative injuries to the knee increased by 8 percent. The reduction in back injuries may be due to the implementation of assist devices, while the increase in knee injuries may be related to kneeling/crawling in low-seam mines. Cumulative injuries were found to remain a major financial burden on the industry. Recently, National Institute for Occupational Safety and Health (NIOSH) developed tools to assist mining companies with incorporating an ergonomics process into their existing health and safety programs. The participating companies have reported tremendous success. Therefore, it is recommended that ergonomics processes be implemented as a means to systematically identify and address the root causes to cumulative injuries and ultimately reduce costs.

Jan 1, 2008

By Barry C. Slocombe

The development of new ports, extensions of existing facilities and reclamation of former docks will involve consideration of a variety of geotechnical problems. This paper presents data including instrumentation of structures from three UK projects involving vibro techniques to provide economic engineering solution.

Jan 1, 2008

By T. G. Carter

Support system design for tunnels and underground excavations has for many years relied heavily on the use of rock mass classification systems and the Hoek-Brown failure criterion as a means for characterizing rock mass behaviour. Because of their development, both the GSI system and the Hoek-Brown criterion admirably characterize most ?normal? rockmasses from the viewpoint of their behaviour for rock excavations. They, however, run into difficulties when applied at the two ends of the rock competence scale. This is largely because block size and incipient strength are such that rockmass behaviour in these domains tends not to be controlled by interblock shear strength but rather by material strength. At the low end of the rock competence scale (UCSi <<15 MPa and GSI generally <30) discontinuities play less of a role and rock mass strength tends to matrix strength. Similarly, at the high end of the scale (GSI >>65, mi>>15), because discontinuities are now widely spaced, block size becomes so significant that again, intact material behaviour rather than the fracturing becomes the dominant factor controlling rock mass strength. In this paper several case examples are presented to illustrate the application of the high-end (spalling) and low-end (weak ground) transition Hoek-Brown relationships proposed by Carter, Diederichs and Carvalho (2007) as a basis for better defining rockmass behaviour at the extreme ends of the rock competence scale.

Jan 1, 2008

By Aurelian Buzaianu, Cristian-Aurelian Popescu, Gabriela Popescu, Petru Moldovan

"A lot of scraps result in processing of composite materials which contain metallic phases that can be recovered and used again in different field. Considering this point of view the aim of the paper was to separate and recover aluminum from aluminum matrix/graphite composites. The separation and recovery of aluminum alloy from aluminum alloy/graphite composites was done by treatment with halide molten salts. As halide salts were used flux tablets that collect the ceramic particles in dross. After dross separation, was used filtration in order to separate the aluminum matrix from the other impurities.Samples from the recovered alloy were analyzed using chemical analysis, optical and electron microscopy, as well as X-ray diffraction. The desired composition of the aluminum alloy obtained from scraps could be reached by some addition of metals to the metallic phase. From optical microscopy it was obvious that the structure of the aluminum alloy obtained after composite reclamation consists large particle of silicon, eutectic, a-Al solid solution and other phases like Fe, Si, Mg and Ni, or some compounds like CuAl2. 1. IntroductionThe research on the recycling and reclamation of metal-matrix composites (MMCs) becomes active to preserve the natural environment, as environmental requirements become stricter, to save energy, and to reduce garbage. In case of recycled aluminum alloy ingot the production energy is about 3 pct of that of the new ingot. This evidence strongly supports the necessity to recycling of aluminum alloys. Among aluminum alloys, metal matrix composites have high strength and elastic modulus, and also good were resistance. These materials have been developed to meet the demand properties which exceeds that of the ordinary materials, and to save energy."

Jan 1, 2008

By J Steyn

Block Cave mining is one method used to extract ore from underground diamond mines as well as other massive orebodies such as copper. This necessitates the excavation of many kilometers of tunnel within the ore body. The integrity of these excavations needs to be maintained over a number of years. Most Kimberlites and weak orebodies are extremely susceptible to degradation when exposed to moisture and the atmosphere. It is therefore essential that some form of weathering protection is applied as soon as possible after exposure. Conventional methods of weathering protection such as shotcrete do not easily fit in with the production schedule, hence the need for a more efficient system that could be applied immediately after exposure and serve as a temporary support or even as a permanent support medium. The main advantages of thin sprayed liners (TSL) compared to shotcrete are the ease of application, speed of application, early strength, much reduced transportation of material, less labour intensive and cost effectiveness. Several Thin Sprayed Liners suitable for various mining environments and geotechnical conditions are available and could be well suited as additional support the undercut level development in a block cave where this may be required. TSL offer a cost effective support solution as an alternative to shotcrete in areas where the building of a support structure is not a requirement.

Jan 1, 2008

By Colin Hardie, Erik Bartsch, Guy Comeau

"The Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik region has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,200,000 tonnes per year due to an Optimization Project (FAG to SAG conversion) in 2005 and many recent processimprovements.In 2006, the Raglan Metallurgical Group with assistance from the Xstrata Process Support group decided to make SAG control one of its priorities in order to further increase throughput and improve stability. The original primary mill control logic delivered by the Optimisation Project in 2005 consisted of a simple PID loop controlling the mill charge (bearing pressure) through feed rate changes. Due to the multivariable, non-linear and disturbance dominated nature of the SAG circuit it was quickly found that this traditional PID control strategy was not able to adequately control the mill; resulting in poor stability, frequent operator interventions and less than optimum performance.This paper describes the successful integration of advanced field systems such as mill feed image analysis (Wipfrag) and crusher gap controller (ASRi), into a multi-variable fuzzy logic SAG mill controller. The process of how a strategy for control was developed and implemented directly in the existing control system (exploiting standard system capabilities) is discussed. It is also shown how this approach has provided mill automation which is simple, robust (despite erratic feed characteristics), and delivers both an increase in throughput and a reduction of variability.INTRODUCTIONOriginally commissioned as a Fully Autogenous Grinding (FAG) circuit in 1997, preparations to convert the Katinniq Concentrator Mill to SAG had in fact commenced as early as 1999, but were halted owing to alternative process improvements which achieved up to 1Mtpa as early as 2000. Up until this time, plant process controls had remained more or less static; modifications having been limited to those required by new equipment. Primary mill process controls and related measurements were at this stage limited to:"

Jan 1, 2008

By Mazin Adnan

The 80m high dam at the Peribonka river in the Canadian province of Quebec was designed for the generation of 385 MW of hydro electrical power (Fig.1). The complex ground conditions required the employment of a variety of geotechnical construction methods stretched to limits never experienced before. Innovative grouting and trenching techniques were used for the construction of a plastic concrete cut-off wall down to a depth of about 116m, to cut hydraulic seepage through alluvial deposits forming the dam foundation. The bedrock where the cut-off wall is embedded forms a glacial gully with steeply sloped flanks, which created further challenging conditions. [ ]

Jan 1, 2008

By G. Konstantopoulou

Environmental degradation due to abandoned quarries is an international problem, more intense when these sites are found in urban or suburban zones, in environmentally sensitive areas or are visible from sites of special interest. Rehabilitation solutions applied worldwide, range from simple relief restoration and planting to more sophisticated site exploitation in order to serve specific social needs. The elaboration of rational rehabilitation plans for every site presupposes deep knowledge and comparative evaluation of all the parameters of the problem. In this paper, a methodological approach of rehabilitation solutions for abandoned quarry sites is elaborated, based on domestic and international experience and practice. Solutions are grouped in eight main categories. In every category the framework of prerequisites and confinements (environmental, technical, social, economic, legal) for their application in Greek quarry site is investigated. A comparative assessment of alternative restoration solutions is introduced, using tools supplied by environmental economics, cost-benefit analysis, G.I.S. and multi-criteria analysis and follows in two stages: 1) Establishment of a set of criteria aiming at a priority list for a number of quarry sites located in a geographical or administrative district. 2) Assessment of alternative solutions for every single quarry from the previous priority list for the selection of the most adequate using technical, economical, social and environmental criteria.

Jan 1, 2008

By William A. Hustrulid

The subject of surface mine development is large. This section covers the fundamental concepts involved in both the open pit mining of thick or steeply dipping deposits as well as the strip mining of thin, shallow, and relatively flat-lying seams or beds. Design involves the marrying of geometries, ore and waste characteristics, equipment, and economics so that the desired result is achieved. Generally, there are many possible combinations from which to choose. For example, extraction over a short time period requires one strategy while quite another is applied for longer times. Variations in supply and demand require some flexibility of operation. Customer requirements impose certain constraints regarding the set of possible designs. Over recent years, planning and operating considerations for surface mining imposed by environmental requirements have increased markedly. There have, at the same time, been enormous advances made in the design aids available to the mine planner. Computer simulation of the various options, whether it be for mine design or equipment selection, provides detailed information for decision making in real time. A significant challenge to the engineer/planner is how to best use the aids avail-able. Because of the widespread use of commercially available and in-house computer software by industry, this section does not deal with the details of planning (for basic coverage of mine development, see Section 7). Rather, some of the basic concepts are stressed. The principles involved in equipment sizing and selection are discussed. A highly important but sometimes over-looked aspect of planning, haul road design, is also covered. For surface mining operations of the future, in-pit crushing and conveying will become even more important. Some of the considerations for application evaluation are included. The section concludes with some future concepts for surface mining.

Jan 1, 2008

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Scott Crabtree, Randy Wheeler

Theoretical description of destructive wave interference and the use of sacrifi cial holes is included and is supported by data collected at Springfi eld Underground. Finally, the process by which the reduction in vibration was achieved in practice is described. Results are discussed for several production blasts taking place over a one year period.

Jan 1, 2008

By N Javati, G D. Carman, D Kikiha, B Likia, K Dala, J McPhie, R Johnstone, D R. Cooke, J L. Blackwell

The 40 Moz Ladolam gold deposit on Lihir Island, Papua New Guinea is the worldÆs largest, low-sulfidation, epithermal gold deposit, in terms of contained gold. The deposit has average grades of 2.42 g/t Au (LGL Resources Reserves Update, 2008) and gold is hosted primarily in refractory pyrite. Lihir Island is part of the 150 km long, Tabar-Lihir-Tanga-Feni, alkalic, volcanic island chain located in the New Ireland basin. Five volcanic blocks comprise Lihir; Plio-Pliestocene Huniho, Kinami and Luise volcanic edifices are built on top of remnant Pleistocene Wurtol Wedge and Londolovit Block (Wallace et al, 1983). The Ladolam gold deposit is located in the central portion of the dissected Luise volcanic edifice and is composed of four main orebodies: 1. Minifie, 2. Lienetz, 3. Coastal, and 4. Kapit. An active geothermal system is overprinted on the ore deposit, localised along north-trending lineaments, and is expressed as hot mud pools and fumaroles. The focus of open pit mapping and drill core logging, as part of ongoing PhD research, has been in the Minifie and Lienetz orebodies. The deposit geology is grouped into four main phases: 1. volcano-sedimentary host rocks, 2. porphyry-style biotite alteration and related hydrothermal breccias and veins, 3. epithermal-style breccias and veins, and 4. modern geothermal alteration. Gold is associated with epithermal-style alteration and mineralisation. Ongoing observations of the Minifie and Lienetz orebodies are highlighting differences in the geology and paragenetic histories. An&nbsp;EXTENDED ABSTRACT&nbsp;is available for download. A full-length paper was not&nbsp;prepared for this presentation.

Jan 1, 2008

By A van Jaarsveld

Environmentally-friendly, safe and cost-effective technology for stope drilling has successfully been introduced at TauTona mine. It has enabled the problem of inadequate compressed air pressure and its downgrading impact on production capability to be overcome. The paper traces the development process which culminated in the conversion of the entire stoping operation at TauTona to electric drilling. Background work which took place at other mines is also described. Statistics of performance improvements are provided. 1. Introduction Holman?s Silver series and the Seco S215 were drills that had a measurable impact on the South African gold mining industry. It is too soon to say whether Hilti will join those great names. However, there is no doubt that the introduction of electric drills into the harsh and unforgiving world of deep level gold mining is a significant development. History has shown that being the first to enter a new technology is no guarantee of long-term success. The pain and suffering which accompany the birth of anything new can deplete the energy of the innovator while at the same time creating opportunities for competitors to leapfrog him. In addition to commitment and enthusiasm, the innovator must therefore also possess, or have access to stamina and resourcefulness to overcome the unexpected difficulties which will inevitably arise. All of these were needed for the Hilti project.

Jan 1, 2008

By K. A. Lewandowski

The efficiency of heap leaching is reduced by poor solution flow characteristics (i.e., channeling and ponding) that result from fines migration. Agglomeration of the ore can immobilize fines, but for agglomeration to be successful in copper leaching, an acid-resistant binder is needed to stabilize the agglomerates. Until now, there has not been a satisfactory method to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? This paper reports on several procedures that have been developed to quantitatively determine whether a binder gives good performance in an acidic solution. These procedures have been used to identify binders that would be suitable for copper heap leaching.

Jan 1, 2008

By FJ Fourie

This paper describes the concept and development of the use of a uni-delay shock tube system in the timing and initiation of the development rounds, specifically in flat development. It was extended from stoping and now constitutes the only initiation system is use at Kopanang mine. The two explosives initiation systems in general use in underground mines are the conventional fuse-igniter cord system, and the more modern Long Period Delay shock tube system, better known as the numbered LP system. Both are well accepted but have many drawbacks which can result in poor breaking and substantial wastage of the blasting material. Both of these deficiencies cause an increase in the cost of a blast. Hitherto, the limited number of delays available has complicated the use of shock tubes in development blasting. Over eighteen month period to the end of 2007, a project team comprising members from Kopanang Mine and AEL developed a method for the use of a uni-delay shock tubes to time any development round. These uni-delay shock tubes are better known as Reef Masters® or EZ-Stopers® depending on the supplier, and the system has particular application in flat development. During the project, two new shock tube system components were designed, tested and manufactured; namely Splitters and Starter Packs. The system has been successfully tested and implemented in both on-reef and off-reef development ends. At Kopanang, it has now been rolled out across the entire mine. Other AnglogoldAshanti mines are conducting trials and implementations into production sections. Initial results indicate improvements in the ground conditions and excavation profiles. The cost of blasting is showing a downward trend. The authors consider that the system is a tool for use in further blast optimization and will contribute to rationalization of the explosives commodities basket on mines.

Jan 1, 2008

Producers with Zero Reportables 2007!: ?New Horizon Mine, Western Fuels Colorado LLC ?Isaacs Run HWM, ICG ADDCAR Systems, LLC ?Savage Mine, Westmoreland Savage Corporation ?South Hallsville No 1 Mine, Sabine Mining Company ?Black Butteand Leucite Hills, Black Butte Coal Company Black Butte and Leucite Hills, Black Butte Coal Company ?Buckskin Mine, Kiewit Mining Group ?Coal Creek Mine, Thunder Basin Coal Company, LLC

Jan 1, 2008

By M. Ahrens

Gearless mill drives (GMD) are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as the development and the progress of GMD systems over the years. With an increasing installed base and many drives operating for many years, there is an increasing need to modernize or revamp existing GMD installations. The first installations of GMD took place in the cement industry and have demonstrated that ringmotors can achieve a lifetime well above 40 years, if maintained properly. The life cycle time of many other components, especially electronic parts, is usually shorter. It is therefore necessary to replace aged or out-dated components early enough in a planned manner in order to reduce the risk of component failures and the related shutdown times. Modernization upgrades can range from minor software updates to a revamp of the cycloconverter. The paper describes typical examples of such upgrades and shows the most important aspects that need to be considered.

Jan 1, 2008

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

By Alexandra Kozak, Rodrigo Costa, Bob Fukuhara

"The Jacobina project in Bahia, Brazil commenced operations in 2004 with a design capacity of 4,200 tpd. A project development plan to increase plant capacity to 6,500 tpd will be discussed. The project included an evaluation of the existing circuit and addressed bottlenecks in the crushing, milling, sedimentation, leaching and tailings transport. These circuits and the methodology used to provide higher capacity will be presented.INTRODUCTIONThe Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc.The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain.The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mine has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. The mine is currently owned by Yamana Gold Inc.In December of 1998, operations at Jacobina were suspended and the property was placed under care and maintenance. Desert Sun Mining Inc. began exploring the property in 2002 and eventually purchased the Jacobina mine in 2003. In 2003, a feasibility study was completed that evaluated the economics of re-developing the mining operations and expanding gold production. In 2004, refurbishment and re-development of the mining operations began and the milling facility throughput capacity was expanded from 1.08 to 1.512 Mtpy (3,000 to 4,200 tpd). The milling operations were commissioned in the 1st quarter of 2005 and commercial production was declared 1 July 2005. In April 2006, Yamana Gold Inc. acquired the Jacobina mine through its acquisition of Desert Sun Mining Inc."

Jan 1, 2008

By Andre Zingano

The objective of this paper is to study the effect of annulus thickness on the quality of resin mixture for fully grouted resin bolt. Pullout and mixture tests were made in underground coal mines for the following arrangements: (a) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with steel wire around the roof bolt; (b) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt; and (c) borehole diameter 0.95 in. (24 mm) and a roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt. The mixture test in steel pipe showed that the best resin mixture is for borehole with 0.95 in. (24 mm). The arrangement (b) produced big voids around the bolt. But for the 0.95 in. (24 mm) hole, arrangement c, the mixture was the best. It was corroborated with the pullout tests results where there is a difference in grout stiffness: the 0.95 in. (24 mm) borehole is about 10 times higher than a borehole with diameter 1.14 in. (29 mm). On the other hand, for the cohesive strength the difference is not significant. Numerical models were built to simulate the pullout tests, and also to simulate the roof support at an intersection. Convergence at two underground intersections, consisting of an immediate roof with laminated sandstone, was monitored to evaluate the performance of the roof supports, using the 1.14 and 0.95 in. (29 and 24 mm) diameter boreholes (i.e. arrangements ?a? and ?b?). The convergence readings showed that the 0.95 in. (24 mm) borehole diameter resulted in a smaller, although it was not significantly different.

Jan 1, 2008