Search Documents

By Victor C. Bryan

One of the most sought after answers in any consideration of blasting activities relative to mines and quarries is how to safely and efficiently use explosives. While that discussion might be relatively straightfonvard in a “site specific” situation. it becomes more complex when viewed from a broad geographic perspective. Such is the case in considering the operations of one United States producer of crushed stone with surface and underground mines spread over a thirteen state area. Differing geologic environments set conditions that dictate to the blaster as now specifically to get optimum results from the blast hole. This treatise is a discussion of the various methods, materials, and principles used in conducting such blasting operations.

Jan 1, 1991

By L. Betteridge, A. Marks

"An OK 300 cu. ft. Skim - Air cell was installed at the HBM&S concentrator in Flin Flon in 1987. Since that time, 3 additional OK Skim - Air cells have been installed in HBM&S concentrators. The cell treats a coarse 70% solids slurry with a residence time of 2.5 minutes. The product from the cell (a unit cell type application) is a final grade copper concentrate with high precious metal values. Since its installation, the cell has improved gold recovery by 10 - 15%. Process variables such as circulating load, pH, froth depth, feed size, and reagent additions all have an effect on the operation of the cell. Maintenance on the cell has been minimal. Initial operating problems involving level control have been significantly reduced and operations are now relatively trouble free. Although very successful at Flin Flon, site specific operating circumstances will determine the suitability of this cell. INTRODUCTIONHudson Bay Mining and Smelting operates four concentrators in Northern Manitoba. Three treat copper-zinc ores, the fourth mills a copper-nickel ore. The Flin Flan concentrator operates two circuits in parallel which treat copper and zinc ores from the Trout Lake and Callinan mines. Both circuits in the Flin Flan mill have Skim-Air cells integrated into the grinding circuits.The Trout Lake cell was installed first and had a payback period of a few months. Required modifications to the cell were made to enhance its performance. These included changing the discharge valve size, tuning the level controller, and installing an insert into the rubber valve sleeve to increase its wear life. The payback period on the Callinan cell was significantly reduced because these modifications were completed prior to its installation.The cells produce a final grade copper concentrate and since their installation gold and silver recoveries to the final copper concentrate have increased significantly. Operating parameters such as coarseness of cell feed dictate the metal recoveries and froth depth determines the selectivity of the cell and therefore the grade of the concentrate.The Skim-Air cell can be suitable in applications where a final product is generated. However, when a bulk concentrate, which requires further separation, is produced, the coarseness of the product may not make it amenable to conventional flotation.The Flin Flan mills Skim-Air cells have worked exceptionally well with little maintenance required."

Jan 1, 1991

By F. A. Aplan, Richard R. Klimpel

This article discusses the role of mathematical optimization techniques as applied to the design and analysis of particulate processing plants. The emphasis will be placed on the macro engineering view of integrated multiple operation plants such as those that typically involve stages of size reduction, sol id-sol id separation, solids storage, chemical reactions involving sol ids, sol ids disposal, etc. The macro engineering view is chiefly concerned with balancing and optimizing the bigger picture of how various unit operations interact technical and economically with each other in an approximate sense rather than how a specific unit operation can be technically described and optimized in detail (micro engineering.)

Jan 1, 1991

By Zhou Lu-Jian

The Port of Shekou is situated at Shenzhen Bay on the east bank of Lingding Ocean. Its coastline is about 6 km long and the water depth near the shore is Favourable. Across the bay is the ' New Territories " of Hong Kong. The port is at a distance of 22-23 seamilesaway from center of Hong Kong and 80 seamiles to Huangpu Harbour of Guangzhou, its highway links with Shen-Guang Highay. Since 19 79 China Merchants Group of the Transportation Department, began to set up Shekou Industrial Zone, the port has been developing and flouri­shing in business. With 15 large or small berths in all, the present portline is 2600 m, and the annual cargo throughout is over 3,000,000 tons and the annual passenger traffic is about 2,000,000 persons. Equalling a medium-scale seaport, it has been officially approved as an oceangoing transit port by the ministry of Transportation. The construction of Shekou port is chara-terized by the self-collected funds and the short construction period. In view of this, the optional plan of the port structure must serve the requirements of simplicity in struture, economy in mate­rial and speed in construction. That accounts for the most application of the sheet piling type to the port in Shekou. Once the project was approved, the cons­truction started. Only within an average period of 7-8 months, a deep water pier was completed and put into operation, which covered series of processes from exploration, designing, tender for con­struction to completion.

Jan 1, 1991

By Ware AR, Doyle BJ, Hoogvliet H

The Ladolam deposit lies within the altered volcanic rocks of the caldera floor, part of which now forms Luise Harbour. It was discovered in 1982 in the course of a reconnaissance drainage sediment sampling programme. This was designed to follow up indications of surface hydrothermal activity noted by Government geologists during an earlier survey of the Tabar-Feni island chain. Diamond drilling began in September 1983 and by the end of 1989 a payable and proved mineable reserve containing 19 million ounces of gold had been established. Rock types and structures are masked at the surface by intense alteration and weathering. An extensive drilling programme has enabled the identification of these features and the relationships between them necessary for an understanding of the factors controlling gold mineralisation. It has also led to the recognition of two distinct phases of alteration. The first phase of porphyry-style potassic alteration was followed by violent caldera formation, producing extensive brecciation and veining. The second alteration phase partly over- printed the first phase and was an epithermal one, evidenced by argillic, advanced argillic and phyllic assemblages. During this event, a large volume of fluids circulated under the favourable structural conditions; these fluids included a sulphur- rich, neutral chloride brine believed to have transported the gold. Boiling and mixing of circulating fluids in the open breccias is thought to have resulted in deposition of the gold. There is evidence that this process is continuing at the present day.

Jan 1, 1991

By Thomas C. Anderson

Tiedback walls are now recognized and accepted as a good solution for a variety of structural problems: ? Retaining Walls and Bridge Abutments in cut situations ? Landslide stabilization ? Repair/support of existing walls Acceptable techniques have been developed for anchoring in cohesive and granular soils and in any kind of rock. Methods have been developed for adequately protecting tieback tendons against corrosion and for testing every tieback to verify its long-term load-carrying capacity. However, the major problem that the industry faces today is how do we get constructable and economical tiedback walls contracted for and built with minimal claims. This paper will explore the issue of "constructability" through a look at specific problems from actual projects. From a research report from the Construction Industry Institute, Austin, Texas (1986), constructability is defined "as the optimum use of construction knowledge and experience in planning, design, procurement and field/operations to achieve overall project objectives." Maximum benefits occur when people with construction knowledge and experience become involved at the very beginning of the project." The design and installation of tiebacks has been developed primarily by specialty contractors; each contractor has evolved its own methods of performing the work, and consequently, many of the techniques are patented and proprietary. The real question is, how do we make effective use of this knowledge and experience during the design phase of the project?

Jan 1, 1991

By Joseph Matoney, B. K. Parekh

INTRODUCTION The term "dewatering" refers to removal of water from coal. Water associated with coal can be categorized as "free or surface" and "inherent or chemically bound" moisture.' The free moisture is found on the surface of coal, in capillaries and small spaces between two or more particles. The inherent or chemically bound water is found in the interior of the coal and as part of coal structure. A significant amount of free moisture can be removed by mechanical dewatering techniques. However, inherent moisture can only be removed by applying energy intensive techniques, e.g., direct or indirect heating. Moisture in the coal offsets some of the benefits of coal cleaning. Extra water in clean coal adds to extra cost in transportation, heat lost during vaporization, and plugging of chutes. From a utility perspective, a 1 % increase in moisture can offset a 4.5% decrease in ash.2 Mechanical dewatering can be classified into two major process categories according to the principles involved, namely, 1. Sedimentation-liquid is constrained and particles move freely. 2. Filtration-particles are constrained by a medium and the liquid flows through. Each of the process categories is composed of various separation techniques shown in Fig. Equipment currently being used by the mechanical dewatering of coal of varying size ranges and final moisture content is illustrated in Fig. 8-2. This figure indicates that sizes larger than 13/, in. (37.5 mm) present no particular dewatering problem. Shaker screens of the very crudest types and designs are capable of producing these sizes at low surface moistures. High-speed vibrators are used for the intermediate sizes and can be used for smaller sizes down to 0.02 in. (0.5 mm) if high moistures (15% surface moisture or greater) can be tolerated in the product. Usually, however, the vibrator is not used below 3/, to 3/, in. (9.5 to 6.3 mm) because of the moisture associated with these fine sizes. At this level, centrifugal force is usually employed to aid dewatering. Centrifuges of various types and designs are used practically

Jan 1, 1991

By Sie A

After completing a feasibility study in 1987, Niugini Mining Limited (NML) obtained five Gold Mining Leases within PA 632, covering the Mount Victor and Clarkes Ridge gold deposits. Reserves prior to mining were 260 000t at 3.63g/t Au for Mount Victor and 40 000t at 2.8g/t Au for Clarkes Ridge. Ore was mined from the two deposits by NML from November 1987 to January 1990. A total of 645kg of gold and 346kg of silver were produced from 198 000 tonnes of ore pro- cessed. Mining and milling operations ceased in February 1990. Since then, there has been significant progress in rehabilitating and revegetating the site. Plant and workshop facilities have been dismantled and removed from site, exposed parts of the pit have been landscaped and replanted, tailings water has been neutralised and discharged, and the dam filled. All remaining personnel and equipment left the site in November 1990. It is envisaged that the replanted areas will be rapidly revegetated, leaving little evidence of mining. Niugini Mining did not recoup the initial investment for Mount Victor, but the mine produced a positive cash flow and made a significant' financial contribution to the local communities and Papua New Guinea as a Whole.

Jan 1, 1991

By Dan McCutchen, Oettmeier

Kelly bar drilling and blasting is unique to Florida, the' Bahamas and other marine limestone areas in the world where blast holes are required but will not remain open for the loading of explosives. This type of rock formation usually yields 1.5 tons of recoverable rock compared to 2.2 tons per cubic yard for competent limestone. The loss of .7 tons per cubic yard is due to voids and sand in the formation. These deposits all contain water to the top of the blast holes which are collared only a few ft. above the ground water level. The working pit is a water filled lake which is excavated from the bank by draglines. These drills have been used in Florida for many years to depths of 65 ft or less.

Jan 1, 1991

By Kanau JL, Kilgour I

This paper describes the metallurgical processes at the 80 000tpd Ok Tedi Mining Limited concentrator, which treats copper- gold ore by single-stage crushing, SAG and ball milling and flotation to produce over 500 000tpa of concentrate. Plant and process developments, including installation of column cells, reduction of fluorine in concentrate, use of sulphidisation and process control improve- ments are also discussed.

Jan 1, 1991

By Li Keqiang

This paper discusses the pile foundation of tall buildings in Shenzhen region. For 156 constructed tall buildings exceeding 18 storeys, about 86. 5 per cent of the sum. The two main types of foundation used are the semi?machine?bored/slurry drilled cast?in?situ pile and the excavation pile (hand ?dug caisson). The engineering geologiical condition in Shenzhen was analysed. In general, the bed rock level is not too deep. It belongs to hard rock, but the geologic structure is more complex and the tectonic fissures is plenty. According to experiences of the researches, tests, designs and constructions of pile foundation, we present the basic design principle of pile foundations for tall buildings as follows; (1) pile strength control to select the pile type and to choice the cross sectional dimen­sions, must be in compliance with the strength of the pile. (2) bearing stratum strongly weathered, moderartely weathered and slightly weathered rock may be used as the bearing stratum. (3) bearing pile bored /drilled cast-in-situ pile designed as an end bearing pile. (4) friction pile precast concrete pile, prestressed concrete tubular pile and driven cast-in-situ pile designe as a friction pile. In case, pile design is in compliance with these principles, it may be safe, economical and reasonable.

Jan 1, 1991

By Conny Postupack

The first principle one usually learns about blasting is that competence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced in a new area, may have co make one or two himself to the new conditions with which he blaster when operating shots just to acclimate is faced.

Jan 1, 1991

The Wamum and Idzan Creeks Prospect, located 79km W of Lae, Morobe Province, Papua New Guinea (PNG) was discovered by the exploration arm of Conzinc Riotinto of Australia Pty Ltd (CRAE). The detailed surface exploration and 11 vertical holes drilled by CRAE, combined with the recent work by Highlands Gold Limited, indicate the occurrence of porphyry copper-gold mineral- isation and associated alteration. The prospect occurs within andesitic volcanics of the Middle Miocene Langimar Beds. It is bounded by NE trending faults to the NW and SE. The alteration and mineral- isation is hosted in the andesitic tuffs adjacent to high level quartz diorite and hornblende diorite stocks. A NW trend to alteration and mineralisation is obvious in Wamum and Idzan Creeks. The main alteration type is propylitic with minor zones of potassic alteration. A late sericite-quartz-kaolinite-pyrite alteration overprinted the earlier alteration and mineralisation. Copper and gold mineralisation is related to a quartz-carbonate-chalcopyr-ite-pyrite (¦ bornite) vein stockwork and biotite ¦ K-feldspar alteration. The mineralisation system at Wamum and Idzan creeks is low in total sulphides. It is considered as a high- level fracture-controlled system with limited low grade Cu-Au mineralisation.

Jan 1, 1991

By Lunt D

Arsenic is classified chemically as a metalloid. That is, it has properties intermediate between those of metals and non-metals. Like non-metals, it combines with many metals to form arsenides (eg arsenopyrite FeAsS, niccolite NiAs, sperrylite PtAs2), but like metals it forms sulphides and oxides (eg realgar AsS, arsenolite As203). Arsenic is distributed widely in the Earth's crust at an average concentration of 1.5 mg/kg and is present in more than 150 minerals.

Jan 1, 1991

By C. J. Kirkland

For two thousand years and more, we insular Britons have been grateful for the existence of the narrow strip of water that separates us from mainland Europe. It has given us a sense of security against invaders, though it has been breached many times. The first recorded serious consideration of a fixed crossing of the English Channel was in around 1802, when it was suggested to Napoleon I. The motive was not entirely peaceable and the British Navy, who saw themselves as defenders of our shores, were decidedly unenthusiastic A whole series of imaginative schemes were proposed in the course of the nineteenth century, embracing viaducts, immersed tubes, artificial islands as resting places for the horses which were to draw carriages, as well as mechanically bored tunnels. The first Channel Tunnel Company was formed in 1872, and an application for permission to construct a tunnel was made to the British parliament. A Colonel Beaumont, of the Corps of Royal Engineers designed and constructed a machine which, in around 1882, bored over a mile of tunnel out to sea from Britain which exists to this day.

Jan 1, 1991

By S. Merjan

Three papers were presented for discussion at the conference: 1) Instrumented driven steel tube piles at Canary Wharf; author: A. R. Gaba, United Kingdom. The author described the Canary Wharf development in the London Docklands, and in particular, the decision to build over the water by driving open-ended steel piles 25m in length into the sands below the soft estuarine deposits. The tubes were then filled with concrete above the sand plug (usually 17m below pile head). Three trial piles were instrumented with: a) resistance strain guages on the inside of the tubes; b) vibrating wire guages on the re­inforcement of the concrete. The trial piles showed elastic behaviour in five cycles of lateral loading, while the verticle load tests showed a definite bi-linear load-settlement behaviour. The initial stiff portion was a result of frictional staff resistance, both inside and outside the tube, with the soil at the base contributing at higher settlements. Loads were taken to three times working load, with no imminent signs of failure.

Jan 1, 1991

Revised throughput rates, as a result of current mining methods and tight controls on mine dilution, have dictated a change in metallurgical philosophy at Renison Limited. Emphasis on throughput capacity increases has altered to a reduction in circuit complexity and operating costs. Extensive surveys of the gravity and cassiterite flotation circuits led to several plant modifications between August 1989 and March 1990. The coarse and fine gravity retreatment roughing tables were by-passed, the coarse gravity retreatment roughing tables were re-commissioned, the cassiterite flotation rougher capacity expanded and the gravity regrind cyclones re-configured.

Jan 1, 1991

By V. M. Troughton

Further pile load testing has been carried out at Canary Wharf to compare the performance of base grouted and ungrouted bored piles founded in the Thanet Sand. The testing regime included three preliminary test piles and two working test piles. The results of these tests are summarised in Table 1 below. Two of the preliminary test piles were located only 14m apart to compare the performance of a base grouted and ungrouted pile in similar ground conditions. The load/settlement behaviour of these two preliminary test piles are compared on Figure 1. All the piles were drilled under bentonite with a drilling bucket. In the base grouted piles four grouting tubes were placed with the reinforcement cage to within 500mm of the pile toe. After the pile had been concreted these grouting tubes were then extended to the pile base by drilling and packers were installed. Grout was then injected into the four tubes simultaneously.

Jan 1, 1991

By Franklin M. Grynkewicz

The subject of bearing pile performance installed by vibratory hammers has been a matter of increasing study and continued controversy. A recent case study from a major bridge replacement project is discussed which provides encouraging data on the use of vibratory pile hammers as a primary means of pile installation and also presents the problems associated with its general acceptance. The bridge project case study foundations consisted of HP 14 x 89 pile sections, designed to develop capacity primarily in friction. Preliminary tip elevations were determined by traditional static analyses. Production pile installation was performed using an IHC S-70 Hydro-Hammer. Driving criteria and final production pile tip elevations were determined after preliminary indicator pile drive tests and static load test results at bridge pier cofferdam locations. Based on impact driven production pile performance, the Contractor wished to investigate vibratory driven piles as a means to accelerate construction schedule. Dynamic pile testing procedures were used as the primary measurement tool and test results were compared to the production pile drive records and prior static load tests. Field testing consisted of driving and monitoring with the PDA impact driven piles to the design tip elevation. Three vibratory driven piles were installed to the same tip elevation and immediately subjected to impact driving and dynamic testing to compare dynamic pile resistance. The results indicated that the site soil conditions were favorable for vibratory pile hammer installation. Recommendations and procedures for proceeding with vibratory hammer pile installation were presented to the Owner. These procedures included quality control in conformance with latest AASHTO recommendations. The Owner, in spite of the site specific data base and QA/QC procedures, would not accept vibratory pile hammer installation, due to the absence of precedence. It is concluded that for vibratory methods to become accepted a rational method of analysis, design and field QA/QC procedures requires development. In addition, the engineering community and Owners/Agencies must be more open to alternate methods of foundation construction. The continued development of dynamic methods of monitoring vibratory pile installation is considered to be key to the general acceptance of this installation procedure.

Jan 1, 1991

By Sun Jiale

This paper presents a brief description of information construction technology for supported excavation to assure satisfactory performance of engineered system. As a successful example of application of the technique, quite a few troublesome problems, such as high groundwater level in soft ground and crowded buildings around the excavation, were solved satisfactorily in the construction of the new tower of Guangzhou Overseas Chinese Manison.

Jan 1, 1991