Search Documents

By Máximo Pérez, Julio C. Videla, Rosa Dzioba

"This paper reports the hydrometallurgical treatment of gravity concentrates of gold samples and outcrops associated with graphite ores obtained from:• flotation tailings of crystalline graphite minerals• outcrop samples of graphitic rock associated with auriferous minerals and free gold located in the Villa Union district and surrounding areas - La Rioja Province - Argentina.Previous studies of the flotation potential of crystalline graphite minerals failed to consider the presence of noble metals.The samples represent a mineralized zone of crystalline graphite which is distributed in different formations with a NE - SW trend in Maz, Punta Colorada and Las Ramaditas hills, covering an area of about 300 square kilometers."

Jan 1, 2003

By Benoit Clermont, Jan Lux

"Magotteaux and Anglo Platinum started a co-operation program with the main aim of establishing the optimum milling configuration measured in terms of throughput, fineness and energy consumption.For this purpose, a fully instrumented pilot milling plant, supplied by Magotteaux (Pty) Ltd, and equipped with a 0.9 x 1.0 m ball mill, was erected at Frank concentrator (Merensky Pt ore). The primary ball mills at Frank concentrator were surveyed in order to set the conditions for the base case. This data was then replicated in the pilot mill under the same configuration. Thereafter, a series of different parameters were varied in order to attempt to optimize the milling system.Only grate versus overflow discharge and open versus closed circuit will be discussed in this paper.It should be noted that this paper does not attempt to give a universal solution as to what milling configuration is optimum in all cases. The conclusions apply for this particular case and probably most others, but it would be advisable to consider each case on its own.CONCLUSION• Overflow versus grate dischargeAn overflow mill has a “pool” of slurry around the toe of the ball charge, which creates a counter lever to the ball charge. This will reduce the absorbed power in the range of 10-15% (depending on the case) and will consequently result in a coarser grind. The tests found a 4% gain in grinding efficiency (Wio) with an overflow mill but this is probably not significant.This lower absorbed power and coarser grind can be counteracted by increasing the ball charge (if below maximum) and/or by increasing the mill volume when removing the grate discharge (a typical grate takes up about 300mm of the mill length).• Open versus closed circuit"

Jan 1, 2003

By B B. Du, Y N. Lu, L X. Wang, S L. Wu

The cohesive zone in the blast furnace is largely affected by the softening and melting behaviour of ferrous burden because of its vital role in the blast furnace process. The Visual High Temperature Methodology (VHTM) has been given to study the softening and melting behaviour of sinter, two kinds of lump ores and acid pellet intuitively. Before softening, both two kinds of lump ore swelled and more serious for lump ore B because of its denser structure than lump ore A. The softening and melting temperature intervals are different from one another and this phenomenon contributed to the gas permeability of ore layer in the cohesive zone since the ‘ore window’ has formed. Besides, the softening and melting behaviour of mixed burdens have been studied, where it has been found that the softening and melting characteristics of mixed burden A (consisting of sinter and lump ore A) is better than mixed burden B (consisting of sinter and lump ore B) and mixed burden C (consisting of sinter and acid pellet) despite the poorest characteristics of lump ore A. The reason is that the high temperature interactivity between lump ore A and sinter is much better than lump ore B and acid pellet. The high temperature interactivity is mainly influenced by the chemical compositions, porosity and contact condition. This paper provides a new research method for the softening and melting behaviour of iron ore and an important technical basis for the optimisation of blast furnace burden.CITATION:Wang, L X, Wu, S L, Lu, Y N and Du, B B, 2017. The softening and melting behaviour of single and mixed iron ore burdens, in Proceedings Iron Ore 2017, pp 605–610 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

n the early days of the Hauraki goldfield (1866 to 1889) almost the only system of ore treatment was wet crushing followed by copper plate amalgamation. A further saving of bullion was in most cases obtained from the tailings by means of pans or berdans. Though this system was not always as efficient as might have been desired it answered fairly well for the bulk of the gold-bearing quartz of the Thames and Coromandel districts, where the gold occurs chiefly in the form of visible particles, and there is not a great deal of silver. It failed, however, with most of the ore found in the Upper Thames or Ohinemuri district, especially in the Karangahake and Waihi portions of the field. In those days the cyanide process was not, and the usual prescription of the mining " expert" was smelting. At Karangahake, many attempts were made to discover a payable method of treatment for the so-called" refractory" ore, but on thewhole with very 'little success, and the district struggled along for a number of years without adding very materially to the production of gold in New Zealand. At Waihi, the Martha Co.'s stamp battery treated by wet crushing and copper plate amalgamation some 18,000 tons from the Martha Reef, worth probablyat least £4 per ton, but the average return was considerably less than £1 per ton, a sum which barely paid working, expenses, and consequently the shareholders were glad...

Jan 1, 1903

Ore from the "Staimite" lode in the Oonah mine, Zeehan, has a complex composition and contains an exceptional number of elements. Its chemical composition has been indicated by the following published figuresà

Jan 1, 1931

By Gabriel S. Esterhuizen

This paper addresses the need for a method to compare the effectiveness of different support systems when designing ground support in coal mines. At present, support design methods include empirical methods based on observations of past performance of installed support systems, analytical methods where the roof is typically simulated by elastic beams and numerical model analysis. The approach presented in this paper estimates the relative stability of a support design through geotechnical evaluation of the rock mass and numerical model analysis of the interaction between the rock mass and the support system. Models are used first to simulate the design performance at the expected rock conditions. The rock strength is then reduced until collapse is indicated in the model. The stability factor is then calculated as the ratio of the expected rock mass strength to the rock mass strength at the onset of collapse, and is similar to the well-known factor of safety used in engineering practice. The stability factor can be used to assist in developing a final support design by comparing the effectiveness of various support systems and the stability of excavations under various geological and loading conditions. Examples of the method?s application in three different geological settings are presented.

Jan 1, 2012

By J. W. Klokow, K. L. Riemer, R. I. L. Ferreira

As a result of the increased depth of mining in the South African gold mining industry mining induced seismicity is a severe problem. One of the strategies within the industry to contain the problem is to incorporate a system of regularly spaced stabilising pillars into mine layouts. At the Driefontein Gold Mine a system of closely spaced dip pillars is used to contain seismic energy emissions. Comparisons of seismic data for several mining clusters initially indicated a possible measure of success in the containment and occurrence of larger events. A detailed analysis of data over a 5-year period since the start of mining however, has revealed a delayed seismic response to the increasing strike spans. Significant changes marked by an increase in certain seismic variables have been observed at mining spans of between 100 to 120 meters and could be of significance to pillar spacing in the design of deep level mining layouts. La sismicité occasionnée par l’exploitation minière est un problème grave dans les mines profondes de l’industrie minière aurifère en Afrique du Sud. Une des stratégies utilisées dans l’industrie a été de maîtriser le problème en incorporant un système de piliers de stabilisation régulièrement espacés dans la disposition des mines. A la Driefontein Gold Mine, un système de piliers de pendage proches les uns des autres est utilisé pour contenir les émissions d’énergie sismique. Au début, des comparaisons de donnés sismiques pour plusieurs groupes d’extraction ont indiqué un succès possible dans la limitation et l’occurrence d’évènements sismiques. Cependant, une analyse détaillée des données sur une période de 5 années a révélé un délai entre la progression de l’extraction et une réponse sismique accrue. Des changements considérables dans les variables sismiques ont été observés dans des intervalles d’extraction entre 100 et 120 mètres, ce qui pourrait être significatif pour l’espacement des piliers dans la conception de la disposition des mines de fond. Resultierend aus den zunehmenden Tiefen des Bergbaus in der südafrikanischer Goldbergbauindustrie stellt sich die vom Bergbau hervorgerufene Seismizität als bedrohliches Problem dar. Es war eine der Strategien innerhalb der Industrie, das Problem dadurch einzudämmen, daß regelmäßig plazierte Stabilisierungspfeiler in den Bergbaulayouts inkorporiert wurden. In der Driefontein Gold Mine wird ein System von knapp aneinandergesetzten im Abfallbereich befindliche Pfeiler benutzt, um seismische Energieemissionen einzudämmen. Vergleiche der seismischen Daten für mehrere Bergbaugruppen zeigten anfangs ein mögliches Maß von Erfolg in der Eindämmung und im Auftreten von größeren Fällen an. Eine ausführliche Analyse von Daten über einen 5jährigen Zeitraum hat jedoch ergeben, daß eine Verzögerung zwischen der Progression des Bergbaus und einer erhöhten seismischen Reaktion besteht. Bedeutende Änderungen in den seismischen Variablen wurden an Bergbauspannen von 100 bis 120 Metern beobachtet und könnten für Abstandsbemessung von Pfeilern im Design des Tiefbergbaulayouts von Bedeutung sein.

Jan 1, 2003

By Bruce Mennie

PT Freeport Indonesia (PTFI) operates copper and gold mining operations in a mountainous area of the Mimika regency, near Tembagapura, Papua (formerly, Irian Jaya), Indonesia. The mining and concentrating operations typically produce 240,000 metric tonnes per day of Copper and Gold ore from the combined mining of an 80,000 tonne per day (ore) block cave operation (DOZ Mine) and a 160,000 tonne per day (ore) open pit mining operation (Grasberg Open Pit). The Grasberg Open pit mine will be complete in 2016 at which time PTFI?s operations will convert to Underground. Mining operations will transition from today?s mixed surface and underground operation to full underground mining over the next 6 years. This paper reviews the history of Redpath?s relationship with PTFI, beginning with a raiseboring contract in 1981 and evolving into vertical and horizontal development contracts of up to 37,700 equivalent metres of lateral development and 4,000 metres of vertical development in 2011. An overview of the current operations (PTFI?s Grasberg Open Pit and DOZ Underground Mines) and transition period (challenges for the transition from current to future underground mines) is presented with details of development of common underground infrastructure and future mines; Big Gossan Mine, DMLZ Mine, Grasberg Block Cave Mine, and the Kucing Liar Mine.

Oct 1, 2010

In blasting large tonnages of ore or material, the economy of the operation 'depends mainly on the mine manager's judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will "bull". The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952

By M. Tangstad, B. Monsen, H. Midtgaard

The increased attention towards reducing emissions of fossil CO2 due to its potential global warming effect has resulted in a focus on renewable resources, as charcoal. Since charcoal is produced from growing wood it does not contribute to global warming. This paper gives a brief review of consequences of and reasons for using charcoal in the silicomanganese (SiMn) production. Results are presented from practical SiMn smelting experiments, on a pilot scale, using charcoal as reduction material and comparing with coke. As slag- and CO2-reactivity are important for furnace performance these features have also been measured.

Jan 1, 2004

By Paul J. Axtell

Self-hardening cement-bentontie (c-b) slurry walls were constructed as shear walls to stabilize the downstream slope of Tuttle Creek Dam near Manhattan, Kansas. The slope stabilization was required to protect the existing pressure relief well system located at the downstream toe of the dam. The wells require protection from slope deformation induced by liquefaction of the foundation sands during or immediately after the design seismic event. The shear walls are transverse to the axis of the dam, unreinforced, and relatively brittle members that may be exposed to relatively large shear strains, and possible cracking, during or immediately after shaking. An extensive laboratory investigation was conducted on recovered core samples to optimize the mix design and stabilization scheme. Furthermore, as is the topic of this paper, a portion of the laboratory investigation was to determine the large-strain, or post-peak, shear strength of the c-b material for use in limit-equilibrium slope stability analyses and numerical deformation modeling to assess the magnitude of permanent deformation caused by the design earthquake. These data may be beneficial to other projects that are considering the use of unreinforced c-b slurry walls for seismic retrofit purposes.

Jan 1, 2010

A Process for the Flotation of Chrysocolla

Sep 13, 2010

By Leon Maday, Dan L. Pecha, Jeremy Johnson, Daniel N. Adams

The Brightwater conveyance system includes 26 km of tunnels, a 130 mgd pump station, 2 km of micro tunnels, and a 2.4 km outfall. The tunnels extend from Woodinville to Puget Sound through varying soils in 1 to 7 bars of hydrostatic pressure and depths to 185 m. The tunnel diameters range from 4 to 6 m and include numerous lining systems. This paper highlights major shaft and tunnel design, including dual cellshafts, multiple pipe configuration tunnels, polymer concrete segments, and the use of a one pass lining designed to convey high pressure effluent.

Jan 1, 2005

In referring to two subjects of interest to the Members of this Australasian Institute of Mining Engineers, I would at the outset desire to express our gratification that to-day we are able to welcome as now united with ourselves, those members who until recently constituted the New Zealand Institute. It is hoped that the amalgamation so amicably arranged may be productive of the best results to all concerned, incorporated as this combination has been at the moment of the fulfilment of that greater political union, the Australian Commonwealth.Since last Annual Meeting held in Brisbane, we have come under the same roof as the Chamber of Mines of Victoria, and we entertain the hope that as that Chamber and this Institute possess so many interests in common in the encouragement and advancement of mining and metallurgical progress in these colonies, that much mutual benefit will ensue. There are many directions in which each body can assist the other, and I trust that a friendly co-operation will be maintained.It is gratifying to feel that in all the colonies a distinct movement is being made to increase the facilities for education in Mining and Metallurgy but if I may refer to our colony of Victoria in particular, we have to express the profound regret that in the means of education in the higher branches, we occupy an inferior position, and it is quite certain that we will continue to do so unless the Government is prepared to subordinate provincial considerations to the weightier.

Jan 1, 1901

By K. Nasrallah

"The Dumont deposit is a large (1,179 Mt proven and probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the project from a scoping study in 2010 through to completing the feasibility study in July 2013.The Dumont deposit in a nickel deposit with the recoverable nickel contained in three minerals; pentlandite, haezlewoodite and awaruite. The minerals are recovered by a combination of flotation and magnetic separation. Over the course of the studies many flowsheet design decisions and changes were made. This paper outlines an overview of the project, flowsheet design including the comminution circuit, desliming and awaruite recovery. The overall resulting flowsheet that was used for the feasibility study is then presented along with the confirmatory locked cycle testing that showed the feasibility design basis was able to produce the predicted concentrate grade and recovery.IntroductionRoyal Nickel Corporation (RNC) is a mineral resource company headquartered in Toronto, Canada, primarily focused on the exploration, evaluation, development and acquisition of base metal and platinum group metal properties. RNC's principal asset is the Dumont Nickel project (Dumont project) located in the established Abitibi mining camp, 25 km northwest of Amos, Quebec. RNC acquired a 100% interest in the Dumont property in 2007. The mineral claims covering the Dumont deposit are currently held 98% by RNC and 2% by Ressources Québec.The Dumont project is located in the province of Quebec in the municipalities of Launay and Trécesson approximately 25 km by road northwest of the city of Amos, 60 km northeast of the industrial and mining city of Rouyn-Noranda and 70 km northwest of the city of Val d’Or."

Jan 1, 2016

By Alexander Garcia

Roof and rib falls are the basic ground control hazards associated with underground roadways during development, stand up and, if applicable, retreat. Falls of ground can happen following the deterioration of supports or rock conditions over time, and particularly as a consequence of continuing rock deformation and/ or failure to install adequate support. Once developed, the risk of a failure is increased due to the effects of time as well as to front abutment stresses through retreat mining. The measurement of strata displacement using monitoring equipment is a form of ground control risk assessment. These monitoring systems are active, or ?live?, in a sense that risk is assessed real-time. However, there are circumstances in which falls of ground can occur without the prior recording of excessive movement. In addition, monitoring equipment is typically placed at set intervals, and strata conditions could vary between these points. Consequently, a visual assessment of other factors contributing to the risk of a fall should be made in order to complete a ground control risk assessment. Such surveys are usually one-off, thus capturing roadway conditions at one particular point in time. Ongoing deterioration is not documented through such one-time surveys, and there is a requirement for real-time or live assessment where a system is in place so that observation data can be updated on an ongoing basis, and a useful summary of prevailing roadway states produced on demand. To address the shortfalls of one-time assessments, a ?live? computerbased quantitative ground control risk assessment process has been developed. It combines visual observations processed in a quantitative manner with existing monitoring data into an interpretable output which indicates zones of roadway where there is an increased risk of a fall of ground from the roof or sides, so that remedial action can be carried out to mitigate that risk. Through improved procedures, it is now possible to generate a ground control risk assessment for each roadway, and one which can be updated frequently. This paper aims to outline and describe the assessment process.

Jan 1, 2012

Demonstration of Solid-Liquid Separations Using Recycled Supernatant that Contains Temperature-Responsive Polymer The effective use of recycled supernatant that contains temperature-responsive flocculant is demonstrated for solid-liquid separations. The recyclability of poly(N-isopropylacrylamide) (PNIPAM) of several different molecular weights and a 15 per cent negatively charged derivative are compared. Batch settling tests of a-alumina suspensions are first conducted at 50¦C, with a subsequent 25¦C period, after which the supernatant is harvested and used to flocculate subsequent suspensions. Using this procedure consecutive separations are obtained with the repeated recycling of uncharged PNIPAM containing supernatant. Batch settling tests indicate that hindered settling rates increase with molecular weight of PNIPAM. Adsorption studies indicate that strong adsorption of PNIPAM onto alumina occurs with PNIPAM at 50¦C and that significant desorption occurs after cooling at 25¦C. However, the extent of desorption decreases with molecular weight resulting in low amounts of PNIPAM for recycling and poor settling behaviour when high molecular weight PNIPAM is recycled. Little recyclability was evident using the negatively charged PNIPAM. On the basis of these findings a recycling-thickener apparatus that uses low molecular weight uncharged PNIPAM is proposed.

Sep 13, 2010

By A. Kapito

The formation of bainite in steel is dependent on the size of the casting, the heat treatment, and the alloying elements. It is difficult to obtain a fully bainitic microstructure in steels during heat treatment because of its close proximity to the martensite (a?) reaction. The ferrite (a) and pearlite reactions in steels are also rapid and shield the bainite reaction. Alloying elements therefore need to be added to separate the bainite reaction. Boron (B) and molybdenum (Mo) are key elements added to bainitic steels because of their ability to retard the a reaction. Other elements used in the production of bainitic steels are silicon (Si), chromium (Cr), manganese (Mn), and titanium (Ti). In this paper we investigate the effect of alloying elements on the bainite reaction through the use of dilatometry. Dilatometry is a technique that determines phase transformations in the steel and through which continuous cooling transformation (CCT) curves can then be developed. Some initial results are presented of an ongoing study on the development of bainitic steels for railway wheel applications.

Jan 1, 2013

By Peter Swanson

A seismic monitoring network has been installed in western Colorado (USA) in the vicinity of three underground coal mines to (i) distinguish and characterize seismic activity as either mining related or naturally occurring, (ii) implement a real-time event monitoring and notification tool, and (iii) collect data for use in research studies aimed at quantifying impacts from mining-related and natural seismicity. These potential impacts include dynamic rock mass failures such as coal bumps as well as strong shaking in the vicinity of critical structures such as impoundment dams, reservoirs, mine seals, mine openings, and steep slopes. Examples of two damaging seismic events are presented and the mining and geologic factors attending these dynamic failures are described.

Jan 1, 2008

By G. Apsey

Eutectic freeze crystallization (EFC) is a novel technique for the recovery of pure salt and pure water from hypersaline waste brines. It is therefore a promising technology for the treatment of industrial waste waters. The impurities caused by crystallizing salt out of multi-component brines by EFC have not yet been investigated, however. To these ends, the selenium impurity found in sodium sulphate, produced from the waste brine of a platinum operation, was investigated. It was believed that the similarity between sulphate and selenate ions allowed isomorphous substitution of selenate ions into the sodium sulphate crystals, which was the likely cause of impurity uptake. It was found that the presence of sodium chloride in the industrial brine promotes the uptake of selenium, while ionic strength of the brine and mass deposition rate of sodium sulphate did not have a significant effect on the selenium uptake. Isomorphous substitution is predicted to be the most significant mechanism by which all impurities will be taken up when applying EFC to other industrial waste brines.

Jan 1, 2013