Search Documents

The copper and zinc contents of herbarium specimens of 11 of the 12 Australian species of Polycarpaea were determined in order to establish background and anomalous values of potential use in biogeochemical prospecting.Cumulative frequency curves were used to establish appropriate threshold concentrations for six species including the "copper plant"' P spirostylis. Collection localities of Polycarpaea specimens with anomalous copper or copper-and-zinc values are under investigation.

Jan 1, 1978

By Peter White

The Hemlo Gold District, located on the north shore of Lake Superior, was discovered in 1981 and will become one of the largest gold mining camps in Canada. Three major Canadian mining companies are presently developing large orebodies and are scheduled to commence production at various times through 1985 and 1986. This paper describes the types of shaft sinking equipment and technology being used by contractors in constructing the required shafts to depths below 1000 metres. The principal shaft design criteria, types of shaft sinking machinery and relevant manpower allocations are discussed.

Jan 1, 1985

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

By A. K. Bhattacharya

Cylindrical bridge piers are widely used and equations exist that can predict the maximum depth of local scour around such piers. Scour around piers is an undesirable phenomenon, as it requires the foundation to be placed to a greater depth resulting in increased cost, making it worthwhile to investigate scour-reducing measures. A number of scour-reducing measures have been tried out for cylindrical bridge piers including placing a concrete collar around the pier, having a delta-wing projecting upstream in front of the pier, placing riprap around the pier, using a group of piers instead of a single pier, having a slot in the pier aligned in the longitudinal direction. The objective of this study is to investigate the effect of upstream protective piles on reduction of maximum local scour depth around a cylindrical bridge pier. The upstream piles are placed at different radial distances in front of the pier and the scour depths are observed. The proposed equation of Dey (1997) for determining the maximum depth of scour around a cylindrical bridge pier is used. The reduction of local scour around the pier is compared with local scour around an unprotected pier.

Jan 1, 2009

By Anthony Treasure

El presente trabajo señala la aplicación de la tecnología EMEW® para la recuperación de metales preciosos a partir de soluciones cianuradas diluidas que contienen plata y oro. La tecnología consiste en un proceso de electroobtención que ha sido desarrollado específicamente para la recuperación de metales en una sola etapa a partir de soluciones, hasta concentraciones de metal muy bajas, de forma que recupera plata y oro a partir de soluciones de lixiviación. Asimismo, este sistema ofrece beneficios como: menor costo de capital, costo de operación, simplificación de proceso, bajo riesgo técnico, mayor recuperación de plata, así como pureza del producto.

Sep 12, 2005

The occurrence of molybdenite in a small shaft in the western margin of the Wuuluman Granite in central western New South Wales is noted. Full petrographic and mineragraphic descriptions are given of a mineralized contact zone between the granite and a basic hornfels.Mineralogical data .indicate a similarity between this mineral occurrence and other occurrences in larger mines remote from the granite.

Jan 1, 1968

By Gilberto Nunez, Ron Eastman, Hector Parra

The prediction of blasting outputs has proven to be a sound engineering tool to provide a guideline for design improvement. It has also been demonstrated to be extremely useful in critical situations when production can be compromised and there is no chance for error.

Jan 1, 2015

By Frank B. Fulkerson

Aluminum production in the Pacific Northwest has a new potential for expansion and increased stability of operation. This new potential results from greater availability of power; lower freight rates on alumina and aluminum; good market prospects for the metal, including western aluminum market expansion following a decline in defense requirements in the 1950's; and possibility of developing bauxite deposits in the Pacific Basin as well as other mineral resources. INTRODUCTION This is a report of a special study by the Bureau of Mines of the primary aluminum industry of the Pacific Northwest. It outlines developments relative to the United States as a whole.

Jan 1, 1962

By John C. Holtz

Interest in the possibility of using Diesel6/ engines for haulage power in mining and tunneling is increasing in the United States, owning largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requests for information as to the factors that must be considered if Diesel engines are to be used safely underground.

Jan 1, 1940

By Sidney Katell

Covering the period from January 1961 through December 1961, this report is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. It is also the third report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related facilities, came from the following sources: 1. A.A.C.E. Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigation. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Utilization. 9. Cost Engineering. 10. Industrial and Engineering Chemistry. 11. Nucleonics 12. Oil and Gas Journal. 13. Petroleum Engineer for Management. 14. Petroleum Refiner. 15. World Oil.

Jan 1, 1962

By N. A. Eilertsen

This paper presents the results of intermittent study begun in 1956 by the Federal Bureau of Mines of yieldable steel arches and yieldable steel ring sets installed for support of development openings in metal mines. Observations were made of this type of support in several iron mines in the northeast and north-central states. The sets, both arches and rings fabricated in the United States, are made from a hot-rolled, cold bent, structural U-shaped steel section in two weights, 15 pounds and 21 pounds per foot. The lighter section is generally used, It is 4.41 square inches in cross section area, and the calculation is that a 6-foot length of this structural shape installed as a supporting column, will safely carry the same load as a Douglas fir post of the same length but of 22 times the cross-sectional area of the steel.

Jan 1, 1962

By J. G. Kirby

The total number of petroleum refineries in the United States continued to decline during 1950, and according to the Bureau of Mines annual refinery capacity survey there were 357 refineries January 1, 1951, compared with 367 a year ago. The total throughput capacity increased 267,344 barrels daily during the year to 6,963,644 barrels daily as of January 1, 1951, continuing the trend of the past several years to increase the throughput capacity of the refineries and decrease the number of plants. The capacity of the average refinery to process crude oil increased during 1950 from 18,246 barrels daily to 19,506. The Indiana-Illinois refinery district accounted for 110,175 barrels, or 41 percent of the total crude-oil capacity increase, the Oklahoma-Kansas district, 17 percent, the California district, 14 percent, the East Coast district, 13 percent, and the Louisiana Gulf Coast district, 12 percent. Slight declines ill crude-oil capacity were reported in the Texas Inland, Texas Gulf Coast, New Mexico, And Appalachian refinery districts. The 160,100 barrels of additional crude-oil capacity that was building January 1, 1951, represents an increase of 10 percent over the year earlier figure. The only completely new refinery listed as under construct ion at the beginning of 1951 is located at Superior, Wisconsin. Other new construction involves enlargement of existing refineries. Plans for at least five additional new refineries are under consideration, and construction is expected to begin during the current year.

Jan 1, 1951

By Monique Pharand, Jeet Basi, Simon Hille

"High quality activated carbon is essential in the recovery of gold in Carbon-in-Leach (CIL), Carbon-in-Pulp (CIP), and Carbon-in-Column (CIC) circuits. Goldcorp’s Campbell complex at Red Lake Gold Mines (RLGM) experienced a period of low soluble gold (Au) recoveries during Q3 2013, during which time the processing plant saw higher than typical Au grades in the CIP tails solution stream. A technical review identified that the CIP circuit may be experiencing a carbon-fouling issue. To further understand the degree of fouling, and to troubleshoot the low recovery problem, samples of carbon were collected from the CIP, elution, acid wash, and regeneration circuits, and submitted for characterization test work. This paper summarizes the steps taken to remedy the carbon-fouling problem at RLGM resulting in increased overall Au recovery.Overview of Red Lake Gold MinesRed Lake Gold Mines is located approximately 450 kilometres northeast of Winnipeg, Manitoba, in Ontario’s western boundary region.All mining is carried out through underground operations, utilizing overhand cut and fill, underhand cut and fill, and long-hole mining methods. Ore types include: silica-replaced carbonate veins with free milling gold, siliceous replacement-type mineralization (rich with arsenopyrite) marginal to veins, broad disseminated sulphide mineralization along major shears, and some minor sulphidized chemical sediment-hosted ore. The operation is supported by two milling complexes: Red Lake, and Campbell.Process DescriptionThe Campbell processing plant's main unit operations consist of grinding, gravity concentrating, flotation, autoclaving, leaching, carbon-in-pulp (CIP), carbon elution and reactivation, electro-winning, bullion smelting/refining and cyanide destruction, and concentrate handling. A schematic of the plant flowsheet is shown in the figure below.BackgroundHigh quality activated carbon is essential in the recovery of gold at many CIP/CIL/CIC processing plants. At RLGM, gold-bearing ore is milled and cyanide is added to leach the gold from the solids into solution. The dissolved gold then comes into contact with activated carbon, and adsorbs onto its highly porous surfaces. Gold is then recovered by separating the activated carbon from the main slurry for further refining. As such, the characteristics and quality of the activated carbon have a significant and direct impact on overall gold recovery."

Jan 1, 2016

By Jean Cayouette

"In 1995, Louvicourt Mine started one of the first paste backfill operations in Canada. From 500,000 tonnes in 1995, the annual paste backfill tonnage produced reached 800,000 tonnes in 1999. The maximum throughput of the surface plant (including binders) is 3,50Ot/d with a final density of 75 to 76% solids which gives a slump of 15 to 17cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders consisting of a mixture of 20% cement and 80% ferrous slag. In certain stopes, the binder ratio may vary from 2 to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.INTRODUCTIONLouvicourt Mine is operated by Aur Resources Inc. which owns 30% of the shares. Its partners are Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corporation (25%). The mine is located in the north-west part of Quebec, about 600 km north of Montreal and about 25 km east of Val d’Or. The mine commenced commercial production in July 1994."

Jan 1, 2002

By Martin H. Rogoff

This publication combines a critical review of the literature on the microbiology of coal with an introduction to those areas of microbiology related to studies of coal as a biological material. The attack on coal by microorganisms as yet remains doubtful. Only the low-rank coals contain an indigenous microbial flora, and even these organisms are not peculiar to coal, but are common soil and water forms. No experimental data have as yet been presented, either in the literature or in the present work, which unequivocally demonstrate the oxidation of coal by microorganisms. Reasons for the resistance of coal to such attack, including insolubility, physicochemical structure, steric hindrance of enzyme action, and the presence of antibiotic materials in coal are discussed. Microorganisms do attack large aromatic molecules and the mode of oxidation of aromatic ring systems by bacteria is presented. Well-defined pathways are known for the oxidation of polycyclic compounds with one to three rings, and these paths with their key intermediates are described and related to the possible oxidation of coal.

Jan 1, 1962

By Lees M. G, Vitnell B. W

The post-war need to increase coal production promoted an intensive drilling campaign. Ineffectiveness in core recovery inclined the coal industry towards percussion drilling rather than diamond drilling. The Joint Coal Board, recognising the greater potential of core drilling, has actively encouraged improvement in techniques and equipment. One outstanding need was a barrel which, over and above other improvements being achieved, would permit recovered core to be examined before it had been subjected to the increased fragmentation and displacement which to date has been inevitable except in core which has been drilled in solid sticks û as New South Wales coal rarely can be drilled. In conjunction with Triefus Pty Ltd a barrel with a split inner tube has now been evolved, as a result of which, core can be more accurately logged, division in to lengths for analysis more aptly made, any core loss more reasonably allocated to appropriate plies, and a greater percentage of core recovered û of the order 95 per cent and more. The one half of the split inner tube is lifted from the other and the logging completed before the core is disturbed.

Jan 1, 1957

By P Hunger, H Günter, F Heinicke

High pressure grinding rolls (HPGR) have been used for more than 20 years to grind iron ore pellet feed. Besides coarse comminution (crushing), where HPGR are installed upstream of the ball mill, there are numerous flow sheets where HPGR are used after ball milling and dewatering for re- or finish grinding.There is a clear growing interest in grinding of pellet feed with HPGR during the last few years. In addition to their known advantages of low specific energy consumption, high availability, low steel consumption and improved pelletising processes the lower environmental load (reduced or no water consumption) became a strong driving factor for the application of HPGR in pellet feed grinding.This growing demand increases the interest in better understanding of the HPGR grinding process with fine iron ore concentrates. One of the most important process parameters is the moisture content of the feed material which influences the performance of the HPGR enormously. The HPGR can react to fluctuations of the fresh feed properties to a certain degree by adjusting grinding force and roller speed. Nevertheless, there are limitations by the physics of the compression process and the capability of water absorption by the concentrate. The capability varies for different concentrates and different specific surface areas. This fact has to be considered during engineering of the beneficiation plant.The paper focuses on the influence of feed moisture content on the HPGR performance in view of throughput, increase of Blaine number and process stability on the basis of numerous pilot plant tests, modelling results and industrial experiences.CITATION:Heinicke, F, Günter, H and Hunger, P, 2017. Influence of feed moisture on high pressure grinding roll pellet feed grinding, in Proceedings Iron Ore 2017, pp 187–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Ivette E. Torres

Aruba, formerly a. part of the Netherlands Antilles, separated on January I, 1986, and became an autonomous part of the Netherlands. Full independence of the island from the Netherlands is scheduled for 1996. In this chapter, however, Aruba's statistics are included with those of the Netherlands Antilles. Tourism continued to be the main industry of the island, which continued to depend heavily on imports, mostly from the United States. During the year, the Government was preparing legislation to regulate the exploration of oil deposits in the relatively shallow sea around Aruba.

Jan 1, 1989

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990