Search Documents

By Timothy C. Siegel

Accurate representation of the geotechnical resistance distribution is critical in evaluating the performance of piles and pile groups for design. A current practice is to infer the geotechnical resistance distribution based on measured changes in strain during conventional top load pile testing. Especially for drilled and bored piles, the residual load is typically assumed to be negligible both during testing and after the application of the structure load. A practical result is that the compressive structural load is anticipated to be opposed primarily by the shaft resistance with little or no mobilized toe resistance. The predicted top deflection is estimated as the combined elastic compression plus the movement necessary to mobilize shaft resistance. The development of residual load (and associated negative skin friction) results in a significantly different design condition. Negative skin friction tends to force the pile into the ground and develops residual load in the pile that contributes to the internal compressive load. Significant toe resistance can be mobilized in order to resist the combination of negative skin friction and the sustained compressive load. The pile movement becomes a function of the toe penetration required to mobilize sufficient resistance to reach a balance of forces. In an effort to study the development of residual load in augered cast-in place (ACIP) piles, the authors installed and monitored strain gages that were embedded in an 18-inch diameter ACIP pile at a site in southeast Georgia. The results of this study indicate that residual load develops over time and reaches a distribution that is consistent with the principles of the unified design of piles. It is concluded that residual load develops in ACIP piles (as well as all drilled and bored piles by the same mechanisms) and that the residual load should be considered in the interpretation of load tests and in the pile design, particularly in the estimation of the single pile and pile group settlement.

Jan 1, 2009

By R. B. Krog

As part of its mining health and safety research program, the National Institute for Occupational Safety and Health (NIOSH) conducted a longwall methane emission and mining time study at a mine operating in the Pittsburgh Coalbed to access the methane emission consequences of mining a longer face. The methane emission contributors from the mining of a longwall face are: 1) gas released from the coal broken by the shearer, 2) gas emitted from the coal on the face conveyor, 3) gas emitted from the coal transported on the belt, and 4) background gas emitted from the coal face and from the adjoining ribs. Based on the results of the study, a set of site-specific mathematical formulas and constants were developed to characterize each of the four longwall emission contributors. The mathematical formulas were then applied to longer longwall face mining scenarios to predict the methane emissions from these faces.

Jan 1, 2006

By S. Ersayin, I. Iwasaki

Application of a magnetic field was shown to be effective in controlling iron losses in pilot-scale cationic silica flotation in the processing of magnetic taconite concentrates. The design of a magnetic field distribution device and batch flotation test results using a 1.42m3 (50 cu. ft.) WEMCO cell are reported. Major losses of iron units in froth products were in the -25µm (500 mesh) fraction, and the application of a magnetic field decreased the flotation of fine magnetite, thereby improving the selectivity of separation. The “as received” sample was sufficiently magnetized and no further benefit was gained by magnetizing treatment. Selectivity was somewhat adversely affected by demagnetizing the sample, though its effect was minimal due to the magnetic field. The device is simple in construction, low cost and may be installed readily in existing equipment.

Jan 1, 2002

By Eugene T. Sheridan

The 24th annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, revealed that 76 producers in 20 States reported commercial production of peat in 1957. In addition to the States that reported production in 1956, Colorado, Idaho, and Wisconsin produced peat in 1957 Forty-four producers reported humus production; 21, reed-sedge peat; and 22, moss peat production. This total exceeds the number of active plants but several producers recovered more than one type of peat. Fifty percent of the total production was reported as reed-sedge peat, 36 percent as humus, and 14 percent as moss peat. About one-sixth of the total production was raw peat, with no preparation other than being air-dried. The remainder consisted of processed peat prepared for use by cultivation, shredding, and/or kiln drying.

Jan 1, 1958

By William E. Young

There are many large rhodonite-bearing veins containing manganese in the Eureka-Animas Forks area of the San Juan Mountains in Colorado. The Sunnyside vein is the largest known vein in the area. As observed on the surface, the vein is mineralized over 8,000 feet and attains a maximum width of 200 feet. The average width of the vein and its branches and ramifications is 58 feet in the area that was mapped in detail. The weighted-average analysis of surface and underground samples from the northeastern extension of the Sunnyside vein is 8 percent manganese. Most other known veins in the area have a similar manganese content. The Hidden Treasure vein lies southeast of the Sunnyside-No Name-Mastadon vein. The weighted average of the analyses of surface and underground samples from this vein is 13 percent manganese. Exposures of the Scotia-Silver Chord vein are visible over a strike length of 4,000 feet on Treasure Mountain. Diamond-drill holes show that the vein contains 10 percent or more manganese to a depth of 400 feet. The vein has an average width of 28 feet. The Independence vein is exposed on the surface for a distance of 600 feet and has an average width of 6 feet. Three cut samples taken across the vein had an average content of 20.7 percent manganese. Sampling of the outcrops of eight veins in the Placer Gulch area also indicates manganese. Numerous other veins cropping out in the surrounding area are similar to the outcrop of the Sunnyside vein system mineralogically and are worth investigating.

Jan 1, 1966

By V. B. Dale

San Manuel has been a modern prodigy from its inception to its present status as a block-caving operation producing 33,000 tons per day. The deposit was discovered, prospected, and developed with modern techniques, and nearly all planning was done from results of an extensive drilling program through an average overburden of 670 feet. The Federal Government had a prominent part in the discovery and primary development of San Manuel. The first 17 holes were drilled by the Bureau of Mines, and discovery of the large, low-grade, disseminated copper deposit is credited to the Bureau. A loan fund of 94 million was granted through the Reconstruction Finance Corporation to the San Manuel Copper Corp. for development of the deposit and erection of concentrating and smelting facilities. Then, while the mine was still being developed, the Defense Materials Procurement Agency contracted to buy a large amount of copper at a pegged price.

Jan 1, 1962

By Shreyas Giridharan, Fursan Hamad, Sujith Gowda, Christian Moormann

"Pile installation in soil is a dynamic process which exhibits large deformation in the soil region. Experimental investigation of pile installation is both time and resource intensive. Numerical investigation can be a helpful tool for the analysis of the installation process. Furthermore, numerical analysis allows simulating various soils and loading conditions with ease. Finite Element Method (FEM) – a widely used framework for numerical simulations - fails to perform well for soil mechanics where large deformation and heavy material movement exists. In order to alleviate this shortcoming, Material Point Method (MPM), advancement to FEM has been used. In MPM, material points (particles) are used to represent the domain which carry the information and move over a fixed computational mesh where the governing equations are solved.In the present work, a variation of MPM, called CPDI (Convected Particle Domain Interpolation) is utilised which handles large deformation problems better than the classical MPM. Here, the material points are represented by a spatial domain which deforms according to the particle deformation. This eliminates stress oscillations while particles cross the grids. Implementation is validated and applied to pile installation in dry and saturated soil conditions. A 2D axisymmetric model is chosen, with penalty function method being used for evaluating contact between soil and pile. Sand is modelled via the hypoplastic constitutive description that takes into account large deformation, as well as small strain stiffness. From these simulations, various parameters like stress, void ratio and friction angle are studied.INTRODUCTIONOffshore piling is challenging in terms of testing and execution. Before the execution, predicting an efficient installation method requires study of various parameters, like soil conditions, type of loading, force requirement etc., and are the minimum parameters to be known beforehand. To obtain these parameters, testing a real scale prototype under different conditions is not feasible. Scaled model tests in lab can support in making certain decisions, but fail to replicate real behavior fully. Therefore, the need for a numerical simulation technique emerges, which can provide early predictions easily and accurately. This later can be extended to real scale tests, reducing the number of experimental investigation required.Simulation of displacement pile installation in sand involves large deformation due to penetration process, thereby making the application of FEM impossible, where large deformation causes heavy mesh distortions. Due to this, meshless methods are developed to treat large deformation in a better way. Among various meshless methods, Material Point Method (MPM) shows more applicability to geomechanical problems. This is mainly due to the ease of handling soil, structure and water in a unified manner."

Jan 1, 2017

By Jean-Marie Fecteau

The gold mine sector is presently facing low gold prices as well as technological challenges. Its competitiveness and survival will depend on new mining methods and equipment to improve ore extraction. In 1999, Natural Resources Canada has invested new funds over a period of three years at CANMET?s Experimental Mine to establish the Narrow-Vein Mining Project. A team of engineers and researchers specialised in mining, mechanics and electronics engineering are working to meet the critical need of ore-extraction technology. CANMET?s program in mechanisation and automation for narrow vein mining had, prior to 1999, realised several important achievements, many in co-operation with a consortium of mining companies (Soredem). The investment of new funds in this area will contribute to develop technologies to improve the productivity, as well as health and safety conditions of the narrow vein mining industry. Several important impacts of this project will be monitored. Specifically, a database of methods and equipment used in narrow vein mining is being developed. A key thrust is to identify operators? needs with respect to the development and automation of mining methods and equipment. Based on those needs, research and development projects will be created. The main problems identified following meetings with mine operators are described with a few elements of solution and the Web site created for the broadcast of the results is presented.

Oct 1, 2001

By M. A. Reyes, L. Yan

Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ

Nov 22, 2019

By F. D. Sutterfield

This study was conducted to provide experimental evidence on the effect of modifications of gasoline front-end composition on the photochemical specific reactivities of automotive emissions. Evaporative and evaporative-plus-exhaust emissions from an automobile operated with four fuels of different volatility and varying levels of C.-C5 olefins were irradiated in a 10040 environmental chamber at three sets of initial hydrocarbon-nitrogen oxides concentrations. Reactivity was measured and expressed in terms of rate-of-NO2 formation and dosages of oxidant, peroxyacetyl nitrate, and formaldehyde. The compositional changes that were necessary in reducing fuel volatility were found to have no significant effect on the reactivity of the emissions. However, replacing C4-C5 olefins with saturated components resulted in sharp decreases in all reactivity manifestations observed for the evaporative emission samples. A lesser influence (of C4-C5 olefin replacement) was found with the composite exhaust-plus-evaporative samples; the effect that was observed could be attributed to the evaporative emission portion of the sample. The data therefore suggest that saturation of front-end fuel olefins had no large effect on exhaust emission reactivity.

Jan 1, 1971

By H J. Stedman

A Transient Electromagnetic (TEM) geophysical survey was trialled in Bowen Basin Permian coal measures overprinted by Cretaceous intrusion. The trial’s intention was to compare whether TEM could assess residual coal more accurately and economically than drilling.TEM results were promising but had limitations. TEM did not compare to drilling for defining coal thickness or relative level definition. However, TEM resolved conductive anomalies laterally; providing a qualitative picture of remnant coal.Three material types and associated conductivities occur within the trial area: overburden (sandstone/siltstone), intrusive sills and heat affected coal.Ground conductivity was analysed by measuring decay of residual current within the TEM loop. Fast decay related to resistive overburden and intrusion, attenuated decay related to conductive coal.Generally speaking, carbon content governs coal resistivity where good quality, low ash, bright coal is more resistive relative to dull, high ash coal. Though in the trial area, relative to intrusion and overburden, coal was found to be the most conductive of the three materials.By modelling conductive anomalies, a general picture emerged of remnant coal regions. Subsequent highwall exposure reconciled with conductive TEM anomalies.CITATION:Stedman, H J, 2017. Findings from a transient electromagnetic trial for heat-affected coal, in Proceedings Tenth International Mining Geology Conference 2017, pp 233–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By V. Svalbonas, M. Fresko

The present versions of the Welding Codes, such as BS7608, have long been known to be compatible with hand computations of membrane and bending stress, rather than detailed finite element solutions. However, in the last five years, in the mining industry, this incompatibility has been largely ignored, and the code interpretations have been pushed into the realms of ground welds, residual stresses, and even flaw growth. Such techniques have to be recognized as extrapolations not necessarily sanctioned by the original code documents. The safety of such extrapolations, as they are related to grinding mill fatigue design, is investigated herein.

Jan 1, 2002

By Job Goostray

IN THIS paper, as in so many other discussions of historical nature, there is little chance for original material and much has had to be rewritten from older papers, documents, accounts, reports, and the like, some of which are of doubtful authorship or contain conflicting statistics. Fully aware of these little historical pitfalls, the authors have tried to quote the origin where possible, and also to seek further confirmation when the statement warranted it, but cannot assume responsibility for certain facts and dates. The Encyclopedia Britannica was frequently consulted. The authors wish to acknowledge assistance from MacKintosh-Hemphill Co.-formerly the Fort Pitt Works-and also from officials of the Watertown Arsenal who loaned valuable books and gave much necessary information. They are particularly indebted to Colonel Dixon of that institution. The data on modern guns were furnished by Mr. F. Brauer of the Watertown Arsenal; Mr. H. S. Chaffee assisted by obtaining records and data of work carried on by the Builders' Iron Foundry of Providence, R. I.

Jan 3, 1925

By Peeler P. K

The recent renewal of interest in hydrometallurgical routes for copper production has been brought about by the possible future reliance on mixed ores and lower grade deposits, environmental aspects, and energy considerations.A number of hydrometallurgical processes for the recovery of copper have recently been proposed. Flowsheets are developed for two processes which incorporate several treatment methods being experimentally studied in Australia.In the first process a cupric chloride leach is followed by electrowinning whilst the second is based on the formation of cuprous ions, stabuized by acetonitrile and subsequent disproportionation to cupric ions and metallic copper. For the purpose of comparison, flowsheets were also developed for the Arbiter and Cymet processes.Process economics are estimated for the four processes and the results are discussed in relation to competitive pyrometallurgy. None of the four hydrometallurgical processes, with possible exception of the Cymet process, appears to be competitive with established large scale and newly developed pyrometallurgical processes for chalcopyrite.However, because the economics of the individual hydrometallurgical processes depend strongly on specific conditions, a "tailored" process may be competitive with pyrometallurgy in particular circumstances.

Jan 1, 1977

By Ting Lu, Gerard Laman

"This document compares the systems of coal classification described under ASTM standards used in Canada to GB standards used in China. A preliminary connection of metallurgical coal classes was set up between the two classifications. In GB classification system, there are nine metallurgical coal groups, namely PS, SM, JM, FM, ½ ZN, RN, 1/3 JM, and QM used in coal blending for coke production. PS coal is almost equivalent to the Low Volatile Bituminous coal; SM, JM, and FM coal groups fall into Low to Medium Volatile Bituminous range; ½ ZN, RN, 1/3 JM, and QM are equivalent to bituminous coal with medium to high volatile matters; QF contains higher volatile bituminous coal compared with High Volatile Bituminous coal. The caking properties commonly used in respective country are also compared in this document. These properties include free swelling index (FSI) and maximum fluidity used in Canada, as well as caking index (GR.I.), and the maximum plastic layer thickness (Y) mainly employed in China. It has been observed that the log of the maximum fluidity has a stronger correlation with the caking index than the Y values. Metallurgical coal processing strategy and typical coking coal product qualities are briefly discussed in the last section of this paper. Currently there is a trend to use heavy medium cyclone in both countries. In Canada the conventional two-product cyclone technology is the preferred practice; whereas in China the three-product heavy medium cyclone arrangement is widely used.INTRODUCTION Coal can be simply classified by applications into two categories: i) thermal coal used to provide heat energy in combustion, and ii) metallurgical coal which is converted to coke, in a carbonization process, and used mainly in the iron and steel industry. Metallurgical coal contains even higher heating values than thermal coal. In addition, it presents unique plastic properties during carbonization which in turn produces a porous solid, high in carbon referred to as coke. Coke is one of the most important raw materials in the iron and steel industry."

Jan 1, 2012

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

THE Broken Hill mining field, approximately 31 miles in length, is at present being exploited by seven companies, viz. : North Broken Hill Limited, Junction North Broken Hill No Liability, Broken Hill Proprietary Block 14 Company, Broken Hill ProprietaryCompany Limited, Sulphide Corporation Limited, Broken Hill South Limited, and Zinc Corporation Limited.The variation in size and shape of the ore-bodies in the mines of these companies, together with the many alterations in pitch and dip, necessitates differences in methods of mining, each company working out its problem in its own particular way.In the matter of chute construction for the handling of the ore broken in the stopes, each mine belonging to the above companies has adopted a style particularly its own, though it may be said that one or two of the types approximate very closely to each other, slight minor differences only being noticed in the design. It is the purpose of this paper to give a brief description of the principal types of chutes now in use in th,e various mines on the field, and in doing so they may roughly be classified into three groups, viz:1. Bulk Chutes, 2. Circular Chutes, 3. Square-set Chutes.The Bulk type of chute is used in the North and British mines of the North Broken Hill Limited, the Central and Junction mines of the Sulphide Corporation, the South Blocks mine of the Zinc Corporation, and the Block 14 mine.The Circular type of chute is used by the Broken Hill South mine and the South Blocks mine.The Square-set chute is used in the Proprietary mine, the Junction North mine, and occasionally in other mines where the square set method of mining is a necessity, and more particularly as mullock passes.

Jan 1, 1925

By Kenneth M. Maas

The Bureau of Mines inventoried all lands in Alaska to determine the availability of land for oil, gas, and coal leasing. Acreage for onshore oil, gas, and coal basins was digitized as was land ownership data. Regulatory policy concerning oil, gas, and coal leasing for various government agencies and private concerns was determined. Oil and gas basins underlie 79.4 million acres of Alaska's 378 million acre landbase. Federal agencies manage 44 million of these acres. The Bureau of Land Management is the lead agency for most oil and gas leasing on Federal lands. Lands have to be specifically opened for oil and gas leasing to be available. The state of Alaska manages 21.1 million acres underlain by these basins. More than 80 percent of this acreage is available for resource development. Native corporations manage the remaining 14.3 million acres of favorable oil and gas land. Coal basins underlie nearly 51 million acres of Alaska. Of this land, 26.4 million acres are under Federal jurisdiction. The state manages 17.3 million acres of land underlain by coal basins. Nearly 7.3 million acres of favorable coal lands are managed by Native corporations.

Jan 1, 1991

By R. Zunich, E. Rybinski, M. Grondin, B. Flintoff

It is uncommon these days to read a business magazine or newspaper without finding a reference to Knowledge Management (KM), and its critical importance to corporate success. One definition of KM is: “getting the right knowledge to the right people at the right time and helping them to put information into action in such ways that strive to improve organizational performance.” In the minerals processing industry we could assert that we have been practicing this for years through effective operator training. In most cases we would probably be wrong. Training has certainly filled the need of addressing safety and basic operational issues, but we must collectively focus on education (learning), and the difference, as measured in outcomes, is not at all subtle. This paper briefly examines the history of training and education in the mining industry, and looks in more detail at the impact of one company’s approach to empower its workforce, while keeping the ultimate goal clearly in mind: “The great end of knowledge is not knowledge, but action.” (T.H. Huxley)

Jan 1, 2001