Search Documents

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By Peter A. Eshun

This paper studies two methods that account for risks associated with gold mining projects such as mineral risks and country risks. The first method is sensitivity analysis, which investigates the effects of a change in any economic parameter such as operating cost, capital investment, gold price or taxes on the viability of the project. The second method is Monte Carlo Simulation technique, which takes into consideration the simultaneous random variation of the economic parameters on the project's viability. An automated simulation cash flow model has been developed as part of this paper. Sensitivity analysis and the simulation model have been used to investigate the economic viability of the Dokrupe Gold Project (DGP) serving as a test case. It is concluded that, the Monte Carlo Simulation technique gives a more realistic judgement of the economic viability of gold mining projects.

May 1, 2004

By David Sprott, Patrick Andrieux

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commercial computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1991

By Morgan L. Race, Matthew R. Glisson

"Most driven pile projects have plumbness limits from 0.25 in/ft (21 mm/m) to 0.5 in/ft (42 mm/m) to control bending stresses. For two projects, the project teams performed static load testing to evaluate performance of piles with sweep. One project, located in Grand Forks, North Dakota, used 9.625-inch (244-mm) diameter piles with a wall thickness of 0.395 inch (10 mm) and lengths ranging from about 130 to 160 feet (40 to 49 m). Measured pile sweep (lateral offset distance of the pile toe from the pile top) was between 12 and 17 inches (305 to 432 mm). Static load testing indicated that the piles could support the design load with axial deflection of less than 1 inch (25 mm) but only provided about 80 to 90 percent of the ultimate resistance at axial deflections of about 1.9 to 1.7 inches (49 to 43 mm), respectively. The other project, located in Shakopee, Minnesota, used 9.625-inch (244-mm) diameter pile but with a wall thickness of 0.352 inch (9 mm) and lengths around 50 to 90 feet (15 to 27 m). The measured sweep varied between about 20 and 63 inches (508 and 1,600 mm) for 9 of 214 piles driven at the site. Load testing indicated that these piles could provide the required design resistance with less than 0.3 inch (8 mm) of axial deflection and support the required ultimate resistance with about 0.5 to 0.6 inch (13 to 15 mm) to of axial deflection.INTRODUCTIONAnyone who has observed a significant number of piles has seen that, inevitably, the pile is not perfectly straight after driving. In spite of the best efforts of contractors, there are a whole host of reasons for piles to end up out-of-plumb or to have a curve, sometimes referred to as pile sweep. Most project specifications set limits for plumbness typically between 0.25 in/ft (21mm/m) and 0.5 in/ft (42mm/m) (USACE, 1991; PDCA, 2007; MnDOT, 2016; MoDOT, 2016). Closed-end pipe piles, including monotube or tapertube, are the only pile type that allow actual measurement of the final alignment of the pile.As Nadeem, et al. (2015) note, buckling failure of long, slender piles is the predominant mode of pile failure in soft soils. Pile sweep is just one source of buckling failure in long, slender piles. The nonlinear buckling analysis showed that increasing slenderness ratio and/or increasing degree of curvature decreases the loadcarrying capacity of a driven pile. Nadeem, et al. (2015) considered solid, steel pile with lengths from 24 to 66 feet (7.5 to 20 m), diameters from 9.75 to 26 inches (244 to 660 mm), initial bends from 2 to 6 inches (50 to 150 mm), and half- and quarter-sine shapes."

Jan 1, 2017

By B. W. Gandrud

[This report presents the data of one of a series of investigations of the washability of Alabama coals as indicated by float-and-sink tests mode by the Bureau of Fines at the Southern Experiment Station in cooperation with the University of Alabama and Alabama coal producers. The Klandyke mine, operated by the Blocton Mining Co., is about 1 mile eat of Vest Blocton, Bibb County, Ala., floor the southwestern, extremity of the Cahaba coal field. The Bureau of Mines already has published three reports that deal with the, washability of Cahaba coals - one a washability study of the Clark bed at Marvel4/ one on the tabling of fine coal from the Thompson and Woodstock beds5/, and the third a washability study of the Henry Ellen bed at Acmar6/.]

Jan 1, 1939

This study estimates costs of producing bituminous coal and lignite by strip-mining methods in 12 hypothetical mines. Basic costs are developed by geographic area, rank of coal, and output capacity. Seam thickness and depth and type of overburden are considered typical for the area in which the hypothetical mine would be located. The cost analyses are based on the use of new equipment, the prevailing union wage scales, and the payment of all miscellaneous costs including royalties, contributions to the miners' welfare fund, and license and permit fees. All model mines are considered to have a life span of 20 years. Capital costs of bituminous strip mines with a capacity of 1 million tons per year range from $12.7 million in the Appalachian region to $16.0 million in the Interior province. The corresponding selling price, assuming a discounted cash flow return of 12 percent on investment, is $5.40 and $6.95 per ton, respectively. For bituminous coal strip mines producing 3 million tons annually, a capital investment of $24.9 million will render a selling price of, $3.46 per ton in the Interior province, whereas a similar mine in the Appalachian region requires a capital investment of $28.0 million to produce coal selling for $4.01 per ton. Subbituminous strip mines of 5 million tons of output per year range in capital costs from $28.7 million in the Southwest to $13.9 million in Wyoming and Montana. Coal produced in the Southwest would sell for $3.03 per ton, while coal from Wyoming and Montana would sell for $1.83 and $1.64 per ton, respectively. The capital costs for the strip mining of lignite range from $6.4 million for an output capacity of 1 million tons annually to $20.7 million for an annual capacity of 5 million tons. The corresponding selling prices of $3.01 and $2.12 per ton, respectively, Indicate the advantages of a large-capacity strip mine.

Jan 1, 1972

By Arthur V. Petty

In Bureau of Mines research on recycling chrome-containing refractory wastes, used refractories from argon-oxygen decarburization and electric steelmaking furnaces were beneficiated. By means of dry magnetic separation on minus 6-mesh crushed wastes, a concentrate was produced. After minor adjustments to the particle size distribution, full-size refractory brick were dry-pressed by a commercial producer and fired to 1,450° and 1,730° C. Standard testing procedures were used to determine the cold-crushing strength, modulus of rupture at 25°, 1,300°, and 1,500° C, hot load, thermal shock resistance, thermal expansion, and slag resistance. Optical and electron microscopy were used to determine grain-bonding mechanisms, and energy-dispersive analysis of X-rays was used to determine elemental distribution. The test results indicate that the beneficiated material could be used to produce a refractory product suitable for moderate-temperature applications.

Jan 1, 1982

By B. Tiryaki

Longwall shearers usually suffer from excessive pick and pickholder consumptions and severe wear of the back plate of the clearance ring section of shearer drums. In practice, most of the drums were seen to be withdrawn from the face due to the abovementioned problems, while vane picks and their holders were intact due to the improper lacing design of the clearance ring picks. However, few underground investigations and their results on the effect of lacing arrangement of clearance picks on the service life of shearer drums have been published. Nevertheless, the pick consumption characteristics of shearer drums were not investigated in detail, since these are fewer pick consumptions with shearers when compared to roadheaders. This paper is concerned with the comprehensive in situ trials on the effect of lacing of clearance ring picks on the lifespan of shearer drums, and the pick consumption characteristics of longwall shearers at Cayirhan Coal Mine in Turkey. The lifespan of shearer drums employed with shearers in this mine increased 70 per cent, while the consumption rate of clearance ring picks decreased threefold through using an alternative lacing for clearance picks, indicating the significance of utilizing proper design techniques for clearance ring picks for the service life of shearer drums. Statistical analyses carried out, using the raw pick consumption data, implied that the clearance ring picks experienced much higher loads than vane picks, revealing that special attention must be paid to designing clearance ring picks. An average maximum consumption value of 41 was determined for clearance ring picks, with corner-cutting picks having the most replacements, while it was 35 for vane picks, on three-day based pick replacements.

Jan 1, 2004

By William J. Campbell

This report describes a Bureau of Mines study undertaken to determine the applications and limitations of solution techniques as a general method of fluorescent X-ray spectrographic analysis. Systematic errors due to variations in particle size, surface preparation, and sample inhomogeneity are eliminated by the use of solutions. The range of applicability of fluorescent X-ray spectrography is increased in two ways: (1) Samples in the form of wire, filings, turnings, etc., can be analyzed as solutions, and (2) samples submitted as solutions can be analyzed as received 0 The lower limit of detectability varies from 0.14 gram per liter for sulfur, atomic number 16, to 0.0015 gram per liter for strontium, atomic number 38. Most elements have limits of detectability between 0.02 and 0.002 gram per liter.

Jan 1, 1959

By Dan A. Brown

Outline ? Basic Concept of ACIP Piles ? Factors Affecting ACIP Pile Performance ? Applications: - Favorable Conditions - Unfavorable Conditions ? Design for Axial Loading ? Lateral Loading Considerations ? Summary & Conclusions

Jan 1, 2004

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

TABAKOTO / SEGALA ? Annual gold production approximately 100,000 oz ? Debt free ? Unhedged ? Combined surface reserves 949,000 oz ? Combined 9 year life Tabakoto open pit reserve 568,000 oz (3.4m tonnes @ 5.26 g/t Au) Segala open pit reserve 381,000 oz (3.98m tonnes @ 2.98 g/t Au)

May 1, 2006

By F. J. Tavera, J. A. Finch

A probe suitable for on-line measurements of gas hold-up in industrial flotation systems has been developed. It is based on an open cell for measurement of slurry-gas conductivity and a novel syphon cell for measurement of slurry-only conductivity. The desired behaviour of the two cells was demonstrated and estimates of gas hold-up were shown to be in good agreement with independent measurements. The gas hold-up probe was used as a diagnostic tool to assess the operation of flotation columns. Differences in gas hold-up between baffled sections in two industrial columns were detected

Jun 18, 1905

By Felipe Calizaya

This study describes the principles involved in the design of a booster fan installation, the basic requirements, and the provisions needed to guarantee a safe operation of the unit. It also describes how a booster fan should be selected and what measures should be taken so that events such as uncontrolled recirculation of air in a mine can be avoided. A computer program called MFSELECT is presented to assist the ventilation engineer in the design process a For a given mine ventilation network, the program determines the duties of fans and regulators that will fulfill the airflow requirements of a mine and minimize the total power consumption. The application of the program is illustrated by the detailed solution of a sample problem. A Case Study based on the Jim Walter Resources' No. 7 Mine is utilized to describe the basic requirements for the design and operation of booster fans, and illustrate their potential benefits in mine ventilation. Finally, the study discusses a process control system designed to evaluate the safety conditions in the mine and report on the status of both surface fans and underground booster fans.

Jan 1, 1990

There are multiple stages in a mining operation that a mining engineer has to draw polygons to be used as operation guidelines. These polygons are drawn by hand and based on engineer?s experience. However, having automatic procedures for forming the shapes can increase the quality and decrease the efforts required. These shapes need to be homogenous in grades and rock types so that the quality and dilution of material sent to the plant can be estimated with the good approximation. In this paper, a clustering algorithm with shape control is introduced which can provide reasonable guidelines for all the aforementioned shapes by manipulating its parameters. At the end, implementations of the algorithm on a small part of a gold deposit with different mining strategies is presented and evaluated based on homogeneity of grade, rock types and determined destinations as well as the shape.

Feb 27, 2013

By Andy Cole

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual-alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

May 1, 2002

By Hong Yong Sohn

Keywords: Barium sulfate, Barium sulfide, Environment, Kinetics, Pollutants, Sulfur dioxide conversion, Thermodynamics Nonferrous smelters and coal gasification processes generate sulfur dioxide streams, most of which are treated to produce sulfuric acid with the accompanying problems of market shortage and transportation difficulties. While the conversion of sulfur dioxide to elemental sulfur has many environmental advantages, no processes exist that are environmentally acceptable and economically viable. A method for converting sulfur dioxide to elemental sulfur by a cyclic process involving calcium or barium sulfide and calcium or barium sulfate without generating solid wastes has been developed. In this process, the sulfate, as the starting raw material, is reduced by a suitable reducing agent such as hydrogen to produce the sulfide, which is used to reduce sulfur dioxide producing elemental sulfur vapor and regenerating the sulfate. The latter is then reduced to reproduce the sulfide. This paper describes work on the BaS/BaSO4 system. Thermodynamic analysis and experimental results indicated that the BaS-SO2 reaction produces mainly sulfur vapor and solid barium sulfate and that the gaseous product from the BaSO4-H2 reaction is mainly water vapor. The rates of the two reactions are reasonably rapid in the temperature range 700-1050°C.

Jan 1, 2005

By R. Mark, R. Richards

The Washington National Cathedral is one of the largest masonry structures in the USA, and like many of its European Gothic counterparts, it required nearly a century to construct. The design was altered during this period, resulting in greater loadings than were originally anticipated on the soil beneath the foundation. When signs of continuing differential settlement were observed in the early 1990's, the Cathedral approached the US Bureau of Mines (now the National Institute for Occupational Safety and Health (NIOSH)) for assistance in monitoring the movements of the massive towers and walls. An array of dual-axis tiltmeters was installed about 40m above ground level to measure wall and tower inclination, with the data sent over a dedicated phone line to the NIOSH Pittsburgh Research Laboratory for processing. Mechanical gages and string-potentiometers are also being used to measure motion across cracks and joints, and differential pier settlement is being monitored with optical-level surveying. Data have now been collected for almost 7 years, and they show a long-term settlement trend masked by dramatic diurnal and seasonal thermal movements. The paper discusses the major findings of the study, implications for the future of the Cathedral, and conclusions regarding the use of geotechnical monitoring at major national monuments.

By R. K. McLimans, C. Knudsen, S. Bernstein, D. Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) is used to analyze indivdual mineral fractions in heavy mineral sands. CCSEM is a fully automated particle analysis technique for the determination of physical and chemical properties of a large number of individual particles. CCSEM enables the precise and accurate determination of the modal abundances of individual mineral fractions (e.g. ilmenite, rutile, zircon, or garnet), their average chemical composition (and compositional variation), as well as their physical properties such as size (e.g. diameter and perimeter length) and shape (aspect ratio and circularity). A unique sample preparation procedure is used to produce representative polished sections from cylinders of raw sand samples such that thousands of grains are present in a polished cross section, but grains are not touching. The combination of this sample preparation technique with CCSEM enables the fully automated analysis of individual grains without the application of de-agglomeration or erosion steps to separate touching particles. Hence, CCSEM yields information representative of the entire area of analyzed grains without systematic bias due to neglect of rim areas by de-agglomeration or erosion steps. Therefore, the resulting data are determined with high accuracy, precision and statistical validity. Because the sample preparation is relatively straightforward, using raw sand samples, and all chemical and physical properties are determined in one analytical session per sample, CCSEM is a powerful cost and time efficient tool for characterizing chemical and physical properties of minerals in heavy mineral sand deposits.

Jan 1, 2005