Search Documents

GENERAL GEOLOGIC DESCRIPTION The mineral deposit of this case study can be described as a "typical" porphyry copper deposit of the southwestern USA and northern Mexico mineral province. The copper mineralization is related to Laramide age intrusives of intermediate composition which have been intruded into older, mostly crystalline, host rocks. Post Laramide deformation and faulting have subjected the deposit to erosion, leaching, and enrichment processes, which have created a secondarily enriched chalcocite zone. Later basin and range faulting down dropped the ore zone, resulting in deep burial beneath late Tertiary conglomerates and gravels, thus preserving the deposit from further erosion and oxidation. Lower grade chalcopyrite mineralization constitutes the primary zone underlying the enriched blanket. MANAGEMENT OF SAMPLE DATA Sample data were obtained from exploration diamond drill holes that were collared vertically and drilled with surface rigs. Most of the holes were surveyed downhole and found to deviate significantly from the vertical. The data were keypunched from original drill hole logs to formats as described in Chapter 6. Three types of cards were prepared: 1) A heading card containing the following information: [Project Name Coordi-in_ Hole Collarnates Bear-clina-Total ID Northing Easting Elevinglion Depth] 2) Individual record cards following each heading card with the following information: [SampleMin. Zone interval Assay Fields Leached (enriched ID From-ToTotal Cu Oxide Cu primary)] 3) Where downhole survey data were available, a card was punched for each downhole survey point. The card image looked very much like the heading card, followed immediately after the heading card, and contained the following information: [Hole Sur Point Sur Point Sur Point ID Bearing Inclination Depth] The keypunched data were then processed by the drill hole survey program producing a record file which contained information as follows: [Line 1. Project Name Date Assay Field Identifiers Line 2. Hole ID Northing Easting Elevation Bearing Inclination Number of Samples Line 3 through N+ 2 (where N equals the number of samples in the hole) Top Min. of Min. Zone Zone Sample Sample Coordinates Sample Assays Leach InterLength Northing Fasting Elev Total Cu Oxide Cu (etc) face] MINERAL BOUNDARY PROBLEM AND TREATMENT According to the geologic description, at least three mineral zones are present within the ore limits, as well as fault boundaries and a buried topographic surface, each of which have to be considered. The interfaces of the various mineralogical and geological boundaries were identified as accurately as possible in each drill hole by the project geologist, the location of the interface was surveyed in the computer program in association with the nearest sample intercept to the interface (note last field of line 3). Thus, the boundary is represented as a point in 3D space at each intersecting drill hole. The linear interpolation (LINTERP) program then searched the last field of the surveyed record to find the top of each mineral zone, or geologic boundary, and read the coordinates associated with that sample point. The program then used the coordinates to compute an interpolated surface between all existing data points as described in Chapter 11. A contour map was plotted for each of the computed surfaces and reviewed by the project geologist. Where the surfaces were poorly defined due to lack of real drill hole information, the geologist, at times, inserted a "pseudo" drill hole intercept according to his best judgment and feeling for the configuration of the surface, and such points were entered into the data stream for LINTERP. When the project geologists were satisfied that they had obtained

Jan 1, 1980

By Charles H. Shamel

I fear most of the Institute members are already weary of the perennial controversy about the apex law. I feel that way about it myself now, though I have been guilty of considerable contribution- to the discussion in the past. The discussion does not seem to perceptibly influence previously held views and I would not again break into print on the subject but for the urgent invitation of the Chairman of our Law Committee. This energetic and able member has firmly determined to secure a revision of the mining law and among other things to eliminate the so-called apex provision from the U. S. mining statutes. He is, however, fair about it and has invited me to make ((the strongest possible argument in its favor." I am suspicious that he is acting on the psychological principle that it is usually easier to convince an audience against a cause vigorously but unsuccessfully defended than against one wholly mute. Nevertheless, I realize that personally he wishes me no harm, much as he hates the apex law, and so am willing that the Institute have whatever benefit may accrue from my taking up again the unpopular side of the discussion. I say this because the attitude of a large part of our "articulate" membership seems irreconcilably hostile; their minds are made up; favorable consideration is foreclosed; and they become impatient and even sarcastic at any attempt to elucidate a favorable view of the apex law. The exact question for discussion at the present time is not whether on abstract, or any other considerations, the apex law is the best possible rule, but the very different proposition whether, after nearly 50 years of statutory life and much longer as a practically universal miners' custom, it is now just and expedient to repeal the apex law. At this point it seems to me that we may profitably devote a paragraph or two to the subject of the origin of law in general, as we are presumed to be considering the subject from the high viewpoint of the general welfare of the nation. The most comprehensive and accurate definition of law in the legal sense is, that it is the body of rules for the regulation of human conduct which is enforced by the State, that is, by the nation.l Legal

Jan 1, 1915

By Thomas T. Read

Mining, which is at least twenty cen-turies old, was at first, and long, wholly a practical art. Little more than two centuries have elapsed since the inception of the idea that general education and a knowledge of natural science would be of advantage to those engaged in the mining industry. Though schools of mining began to develop in Europe early in the eighteenth century the concept of educational preparation, for technical conduct of the industry was slow in winning general acceptance in the industry itself. John Hays Hammond, in his autobiography, recalls that when he sought employment with a mining company after he had graduated from Yale and Freiberg he had to assure its executive, before being even considered for employment, that he did not consider that he had learned anything about mining. This was as late as 1880. Existence in the industry of a prejudice against education of the academic type is perhaps an explanation why inadequate provision has been made by the mining industry for the continuing education of technical employees after they enter employment, although engineering education prior to engaging in industry has now won general acceptance. I am familiar with the existence of 'loop" courses for engineering graduates in metallurgical plants, of schemes for giving mining graduates "practical experience," and of the interest in vocational courses for workmen which sprang up in the period of labor shortage during and immediately following World War I (but which quickly died when the depression of 1921 again made experienced workmen available in sufficient supply), having been chairman of a committee appointed by the Mineral Industry Education Division to make a survey of existing provisions for post-employment training for engineers in our industry. The results of that survey, reported elsewhere, clearly indicate that it is inadequate as to amount; the aim of this paper is to present evidence for belief that it is also inadequate in quality. To avoid becoming too involved, no reference will be made here to post-employment vocational training for workmen, which is a subject differing so much from post-employment education for engineers as to require separate treatment. Neither will postgraduate education for metallurgical engineers be discussed, becadse a distinction must then be made between training for research work and for plant operation, whereas mining engineers engage almost exclusively in operations. Since the situation in the coal-mining industry has been discussed at several recent meetings, that also will be passed over, and what follows should be taken as a discussion applying exclusively to the metal-mining industry. Professional Development In the operations field (both in mining and metallurgy) the work to which a beginner is assigned is seldom closely related to previous academic education. The contrast is almost as great as between

Jan 1, 1943

By Thomas T. Read

Mining, which is at least twenty cen-turies old, was at first, and long, wholly a practical art. Little more than two centuries have elapsed since the inception of the idea that general education and a knowledge of natural science would be of advantage to those engaged in the mining industry. Though schools of mining began to develop in Europe early in the eighteenth century the concept of educational preparation, for technical conduct of the industry was slow in winning general acceptance in the industry itself. John Hays Hammond, in his autobiography, recalls that when he sought employment with a mining company after he had graduated from Yale and Freiberg he had to assure its executive, before being even considered for employment, that he did not consider that he had learned anything about mining. This was as late as 1880. Existence in the industry of a prejudice against education of the academic type is perhaps an explanation why inadequate provision has been made by the mining industry for the continuing education of technical employees after they enter employment, although engineering education prior to engaging in industry has now won general acceptance. I am familiar with the existence of 'loop" courses for engineering graduates in metallurgical plants, of schemes for giving mining graduates "practical experience," and of the interest in vocational courses for workmen which sprang up in the period of labor shortage during and immediately following World War I (but which quickly died when the depression of 1921 again made experienced workmen available in sufficient supply), having been chairman of a committee appointed by the Mineral Industry Education Division to make a survey of existing provisions for post-employment training for engineers in our industry. The results of that survey, reported elsewhere, clearly indicate that it is inadequate as to amount; the aim of this paper is to present evidence for belief that it is also inadequate in quality. To avoid becoming too involved, no reference will be made here to post-employment vocational training for workmen, which is a subject differing so much from post-employment education for engineers as to require separate treatment. Neither will postgraduate education for metallurgical engineers be discussed, becadse a distinction must then be made between training for research work and for plant operation, whereas mining engineers engage almost exclusively in operations. Since the situation in the coal-mining industry has been discussed at several recent meetings, that also will be passed over, and what follows should be taken as a discussion applying exclusively to the metal-mining industry. Professional Development In the operations field (both in mining and metallurgy) the work to which a beginner is assigned is seldom closely related to previous academic education. The contrast is almost as great as between

Jan 1, 1943

By B. H. Caudle, A. B. Dyes, R. A. Erickson

The study of the influence of fluid mobilities on the sweepout pattern resulting from the injection of gas or water has been extended to cover the production period which follows breakthrough of the injected material. Mobility ratios over the range common in field operations (0.1 to 17) were studied for several pattern floods (five-spot, staggered, and direct line drive). The experimental data required for these studies were obtained by the use of the x-ray shadowgraph technique using miscible oil phases of different viscosities in porous plate mode1s of a reservoir element. From the shadowgraph pictures obtained before and after breakthrough of the injected fluid, flowing ratios at the producing well and cumulative volumes injected were calculated. The method for applying such data in predicting field behavior is illustrated for a water flood of a five-spot. For this case a range of mobility ratios of 0.5 to 5.0 results in: (I) nearly complete (95 to 100 per cent) sweepout pattern efficiencies at abandonment conditions, (2) production after breakthrough being responsible for as much as one-third of the total recovery at the lower mobility ratios, and (3) a twofold variation in the operating life of the reservoir. In determining the merits of a secondary recovery operation, the fraction of the reservoir which is ultimately to be swept by the injected fluid is of major importance. Because of its significance a large amount of research has been applied to the study of areal sweepout efficiency. Muskat, Wyckoff and Botset1,2 have presented the classic analysis of the pattern efficiency at breakthrough for several injection patterns in which the mobility of the fluids ahead of the injected phase front was equal to the mobility of the fluids behind the front. Aronofsky3 as extended this analysis of recovery at breakthrough through numerical computations and by the stepwise use of the potentiometric model to include the effect of different fluid mobilities ahead of and behind the invasion front on the line drive performance. Fay and Prats' have also employed numerical computations to show the influence of one other condition of fluid mobilities on the five spot flood. In a previous paper' a new method of attack on this problem which employed x-ray and porous plates was described. At that time experimental results were also presented which described the effect of fluid mobilities on the reservoir area contacted by the injected fluid at breakthrough for the five spot and direct line drive patterns. Most of the literature pertaining to sweepout pattern efficiency has emphasized the pattern which is obtained at breakthrough of the injected phase. The increase in the sweepout pattern which occurs after breakthrough

Jan 1, 1955

By William F. Harris, Joseph Easha

FOR many years basic control of refinery operations depended on visual observation of small chill specimens poured at various intervals during processing. The oseto of these samples was related to the physical and chemical properties of the metal. Since the =setn is dependent on many factors other than oxygen content, this method, while giving a general indication of the condition of the copper, does not accurately measure the oxygen content. For the last 3 years a modified vacuum fusion procedure which enables the operator to determine the oxygen content of the copper within 1 5 min of sampling has been in use at the Westinghouse Copper Mill. For use with this apparatus a sampling technique has been developed which gives oxygen values representative of the oxygen content of the wire bar. The sampling technique is based on a statistical study, which compared the oxygen content of the laboratory sample of copper poured at the same time a wire bar was being poured, with the oxygen content of the wire bar. The apparatus used for the determination of oxygen in copper is shown in Fig. 1 and is essentially the same as previously described but with one important modification. A very porous fritted glass disc has been inserted in the tubing between the manom- eter and 40/50 ground glass joint. The fritted disc retains the copper vapor and copper particles in the furnace section and prevents contamination of the mercury in the manometer. Without the disc the manometer became difficult to read after a few weeks of operation. In earlier work1 it had been established that the simplified vacuum fusion apparatus used at the Copper Mill gave essentially the same results as a con-vential vacuum fusion apparatus. However, for this study it was necessary to determine the difference, if any, between the oxygen content of the wire bar and the oxygen content of the small chill sample used for the oxygen analysis. This correlation was established by taking a chill sample at the same time wire bars were being poured. The wire bar being poured at the time the chill sample was taken was marked and removed for further analysis. The copper is sampled at various times during refining and cast into laboratory size samples with the mold shown in Fig. 2. The mold is made of cold rolled steel and is 2 in. high and 2 1/2 in. in diam. The large upper portion of the cast sample is used for measurement of the conductivity of the copper, The lower portion which is a rod about 1/4 in. diam by 3/4 in. long is used for determination of the oxygen content. This portion of the sample weighs about 5 g which is approximately the size sample used for the analysis. The only preparation neces-

Jan 1, 1962

By E. A. Jones

THE Southeast Missouri division of the St. Joseph Lead Co. normally hauls and hoists over 5 million tons of lead ore each year. This ore is mined in the stopes and headings of 20 mines, hauled to a main line system, see above, and transported up to 6.4 miles to ore-hoisting shafts. Average haulage distance is 2.16 miles. A few years ago a distinguished mining engineer visiting this area for the first time remarked, "You do not have a mining problem; yours is a haulage problem." Its relative importance may be gaged by the fact that mine haulage represents about 25 pct of the total cost of mining ore, the most costly single underground operation. The Southeast Missouri lead belt is a mining district located about 65 miles south of St. Louis. This district is roughly 6 miles wide and 10 miles long. The ore horizon lies about 400 ft below the surface where most of the ore is mined from flat-lying beds of dolomitic limestone. This paper deals with the central part of the district, namely, that portion which contains a group of interconnected mines all in a central haulage system, serving four hoisting shafts. The two major hoisting operations are carried out at Federal No. 17 shaft and Leadwood No. 12 shaft. No. 17 accounted for about 70 pct of the ore hoisted in the district during 1950, averaging about 14,000 tons per operating day. The underground dumping and skip-pocket system at this shaft is similar to those of the other shafts except that it has two rotary dumps. The other ore-hoisting shafts have only one. It might be mentioned that waste rock is hoisted at still other shafts, hauled off, and dumped on the surface by trucks. The hoisting shafts are on a connected system of about 200 miles of underground 24-in. gage main line railroad. There is also the Bonne Terre system, with its own ore-hoisting shaft, which consists of 13.5 miles of 24-in. gage main line, located in the extreme north portion of the lead belt area. Smaller outlying mines such as Doe Run No. 12 and Hayden Creek operate on trackless or shuttle car haulage. In addition to the system of main line haulage, each contributing mine group has its own extensive system of stope or heading railroad. Trackless mining is making considerable headway in the Lead-wood and Desloge mines. Here the shovel loads into a shuttle car which in turn dumps into mine cars spotted on the main line track system. When the merits of underground haulage and surface transportation are compared, it must be remembered that in early days there were many individual

Jan 1, 1954

By J. Kent Smith

VANADIUM is generally spoken of as a rare element; but, even in the light of our resources as known a couple of years ago, this description could be accepted in a qualified sense only. In fact, vanadium is very widely distributed, being a constituent of most clays, while even caustic soda has been shown to contain almost regularly a minute proportion of it, although the quantity in each case is so small as to render impracticable the extraction of the metal there from with profit. The opening-up of a large deposit of vanadium sulphide ore in South America has put a new phase on the commercial outlook of vanadium, the technical value of which for the improvement of steel has been proved by rigorous scientific investigation.

Sep 1, 1907

By D. O. Wyble, L. O. Bacon

THERE has been considerable speculation among mining geologists and mining men in general as to the relative merits of gravity methods in iron-ore exploration. Most of the investigations which have been carried out in recent years have been done by mining companies, and few if any of the results have been published. Three gravity surveys have been made in the Iron River-Crystal Falls area,' " one by the U. S. Bureau of Mines, with inconclusive results, and the other two by Radar Exploration Co. for the Cleveland-Cliffs and the M. A. Hanna companies, with results not known to the writers. Both the last-mentioned surveys were detailed investigations, the stations being spaced as close as 10 ft along traverses,' and were made to determine the feasibility of locating iron ore by gravitational methods. Because of the presence of a large body of ore already extensively drilled, Dr. Harold L. James of the U. S. Geological Survey, Iron River, Mich., suggested that a further test of gravitational methods of exploration be made in the Round Lake area of Iron County, see Figs. 1 and 2. This survey indicated a considerable regional gradient and led to a study of the surrounding gravity field and its relation to the major structural features of the syncline within which the iron formation lies. The southwestern part of Iron County presents a series of hills and hollows elongated in a roughly north-south direction. The bedrock topography is of pre-glacial origin. Relief is moderate; a maximum elevation difference of approximately 350 ft was observed during the survey. Major drainage is dendritic with the larger streams: the Brule to the south, the Paint to the north, and the Iron in the central part. Hills are thickly grown with hard- woods, and lowland areas, not under cultivation, are usually covered by second-growth softwoods. The area covered in this paper includes the southern half of Iron County, Mich., with a deep synclinal basin occupying the central part of the area, and the southeast corner of Gogebic County, immediately to the west of Iron County. The upper Huronian iron formation, slates, and graywackes which form the synclinal basin rest upon a greenstone basement. The basin has not been completely outlined by exposures, drill records or other means, as outcrops are scarce and the thick mantle of glacial drift makes geological investigations extremely difficult. Glacial drift varies in depth up to 300 ft or more. The drift is usually thickest under the hills and is thinnest in the depressions and along drainage courses where most of the bedrock exposures occur. The area over which gravity investigations were made is almost, entirely covered by glacial material. Bedrock of the basin consists of a complexly folded series of iron formation, slates, and graywackes. One of the series of slates has a high magnetic susceptibility due to the fine-grained magnetite it contains. This formation can be detected readily. by magnetic methods and provides a marker horizon which can be easily followed. The magnetic slates are stratigraphically above the iron formation, and much of the geological interpretation of the area is based upon the magnetic anomalies they produce.

Jan 1, 1953

By L. O. Bacon, D. O. Wyble

THERE has been considerable speculation among mining geologists and mining men in general as to the relative merits of gravity methods in iron-ore exploration. Most of the investigations which have been carried out in recent years have been done by mining companies, and few if any of the results have been published. Three gravity surveys have been made in the Iron River-Crystal Falls area,' " one by the U. S. Bureau of Mines, with inconclusive results, and the other two by Radar Exploration Co. for the Cleveland-Cliffs and the M. A. Hanna companies, with results not known to the writers. Both the last-mentioned surveys were detailed investigations, the stations being spaced as close as 10 ft along traverses,' and were made to determine the feasibility of locating iron ore by gravitational methods. Because of the presence of a large body of ore already extensively drilled, Dr. Harold L. James of the U. S. Geological Survey, Iron River, Mich., suggested that a further test of gravitational methods of exploration be made in the Round Lake area of Iron County, see Figs. 1 and 2. This survey indicated a considerable regional gradient and led to a study of the surrounding gravity field and its relation to the major structural features of the syncline within which the iron formation lies. The southwestern part of Iron County presents a series of hills and hollows elongated in a roughly north-south direction. The bedrock topography is of pre-glacial origin. Relief is moderate; a maximum elevation difference of approximately 350 ft was observed during the survey. Major drainage is dendritic with the larger streams: the Brule to the south, the Paint to the north, and the Iron in the central part. Hills are thickly grown with hard- woods, and lowland areas, not under cultivation, are usually covered by second-growth softwoods. The area covered in this paper includes the southern half of Iron County, Mich., with a deep synclinal basin occupying the central part of the area, and the southeast corner of Gogebic County, immediately to the west of Iron County. The upper Huronian iron formation, slates, and graywackes which form the synclinal basin rest upon a greenstone basement. The basin has not been completely outlined by exposures, drill records or other means, as outcrops are scarce and the thick mantle of glacial drift makes geological investigations extremely difficult. Glacial drift varies in depth up to 300 ft or more. The drift is usually thickest under the hills and is thinnest in the depressions and along drainage courses where most of the bedrock exposures occur. The area over which gravity investigations were made is almost, entirely covered by glacial material. Bedrock of the basin consists of a complexly folded series of iron formation, slates, and graywackes. One of the series of slates has a high magnetic susceptibility due to the fine-grained magnetite it contains. This formation can be detected readily. by magnetic methods and provides a marker horizon which can be easily followed. The magnetic slates are stratigraphically above the iron formation, and much of the geological interpretation of the area is based upon the magnetic anomalies they produce.

Jan 1, 1953

By L. W. Saperstein, Y. J. Wang

The development of computer programs to solve complex ventilation networks has reached a point of refinement where these programs become a necessary tool of the ventilating engineer. Such a program is presented. This program has an increased efficiency over its predecessors; it also includes the important facility of fixed quantity branches. This is in addition to the earlier capabilities of free-splitting, internal or external fans, and natural ventilation pressures. The program is written in Fortran IV with double-precision arithmetic and is listed here. Sample problems with input and output are also given. The recent, and presumably continuing, official interest in mine safety is bound to result in more stringent control requirements for ventilation. Anticipating this requirement, the Dept. of Mining, The Pennsylvania State University, has developed a computer program for the solution of complex mine ventilation networks. It is the opinion of this department that the program has sufficient merit to warrant its use in normal industrial operating conditions. Although the undergraduate mining engineering students of this department are routinely trained to use the program, it was felt that this training did not present a fast enough means of dissemination; consequently, this paper was written. The conception of the program is not new;1; however, the present version incorporates features that changes it from a scientific endeavor to a useful operating tool. These features include those of earlier programs, such as free-splitting, external or internal fans, and natural ventilation processes plus the important ability of handling fixed quantity branches, and of increased efficiency giving reduced cost. The facility for fixed quantities will be discussed in more detail. The solution of any network depends upon satisfying Kirchchoff's laws. These state that the sum of flow at any junction is zero, and that the sum of the pressure drop in branches totals the pressure drop in the mesh constituted by those branches, that is that the pressure drop around any mesh is zero. The terminology is derived from Synge," and is, in fact, that used by Topologists. A branch is any airway of uniform characteristics; a junction is where two or more airways meet (the minimum number of two airways is useful for describing the point where a low resistance airway changes into a high resistance one due to some physical constriction); a mesh is a path, along some branches, that returns on to itself, but does not need to traverse the same branch twice in order to do so; and a tree describes all those branches in a network which, while connected through all the junctions, do not form any meshes. Obviously the branches-in-tree are open-ended and can be shown to be one less than the number of junction (J-1). The branches-out-of-tree, also called basic branches, are equal to the number of basic meshes and are M = N — J + 1, where M is the number of meshes and N is the number of branches. The major difference between this network and an electrical one is that the law attributed to Atkinson for pressure drop is utilized rather than Ohm's law. Atkinson stated that the pressure drop (potential) is equal to a resistance factor multiplied by the quantity squared. This is written H = RlQlQ where H is the head loss. Q? is written in this factored fashion so that H will always have the same sign as Q. A negative sign is used to indicate that flow in a branch is opposite to that of its containing mesh. A mesh takes the direction of its basic branch. Utilizing Atkinson's law in Kirchchoff's second law and bearing in mind that the first law must remain satisfied, the program will determine all quantities, or head losses as they are related, for the branches of the network. The program uses a Geuss-Seidel form of in-teration, starting from an arbitrary Q and using a correction factor of the type first suggested by Professor Hardy Cross' that will handle the nonlinear equation of Atkinson's law. A fuller description of the interative process is included in Wang and Hartman.' Iteration continues until the correction factor is less than or equal to a preset error (E) or until a maximum number of iterations (MAXIT) have been reached. Utilizing an E of 50 cfm, sample problems have had rapid solutions. Rapidity of solution is also ensured by the method of selecting meshes and basic branches. This is done by the computer, which chooses the highest resistance branches, fixed quantity branches, and those containing fans, as basic branches. Natural ventilation pressures are handled as fans of constant pressure and may be assigned to any branch. The computer will generate a fan characteristic by polynominal fitting if a few operating points from the desired fan are input. A fan may be placed in any branch of the network, except those with fixed quantities. The strength of the present program over its earlier versions is its ability to handle fixed quantity branches. This means that certain branches can have their quantity determined, or preset, by the ventilating engineer. Operating under this constraint, the program will analyze the network and output the pressure change necessary to achieve this desired quantity. A call for positive head loss would require an auxiliary fan; negative head loss would require a regulator. This represents a powerful tool for the ventilating engineer who must insure that certain quantities of air pass across the operating faces or through working stopes. McPherson6 suggested that a ventilation program would be useful for determining in advance which branches were receiving inadequate air, and that subsequent calculations would then indicate the necessary corrections. The present program makes these corrections. Thus the mine manager can know immediately the consequences of changes to his system;

Jan 1, 1971

By J. H. Wernick, J. E. Kunzler

HIGHLY pure metals are needed for low-temperature electron transport studies in progress. Recent improvements in purification techniques, such as zone refining, have made it possible to obtain metals with improved purity. For some metals, the improvement has been to the extent that ordinary analytical techniques are inadequate and special methods are needed.1 For other metals purification is more difficult, so that simple but rapid analytical methods are desirable as an aid in evaluating the effectiveness of purification procedures. Furthermore, it is desirable to be able to determine the impurity level of the sample or ingot with the minimum of physical disturbance of the material. In order to aid in the preparation of purer metals, techniques involving the measurement of electrical resistance at liquid-helium temperatures have been devised for studying impurity distributions in zone-refined ingots and other bulk samples without destroying the ingot or its geometry. The method yields information on the variations in purity along the length of the ingot or sample and provides a measure of the overall purity of the material. Compared with ordinary analytical methods, the resistivity method is rapid, sensitive, and does not require significant physical disturbance of samples with reasonable shapes. It has the disadvantage that resistance measurements are not specific, i.e., they do not identify the impurity. However, this disadvantage is offset by the advantage of being able to establish a measure of the overall purity so far as electrically active" impurities are concerned. METHOD AND ITS BASIS The method is based on the well-known fact that the resistivity, at Liquid helium temperatures, of a reasonably pure metal containing no regions with additional phases decreases with increasing chemical purity or a decrease in the number of physical defects. It is convenient to separate the total resistivity into three parts: where is the resistivity due to the scattering of the conduction electrons by the lattice vibrations or phonons, p is the contribution due to physical defects, and originates from the effect of chemical impurities in the metal. Insofar as Matthiessen's rule is obeyed,2 pphys and pchem are independent of temperature. Except possiblyin the very purest metals, ptherm is negligible at liquid helium temperatures and For zone-refined metals, which normally are well annealed and consist of large grains, at the chemical purity levels thus far attained the available data indicate that pphys is negligibly small or at least constant throughout the ingot. Assuming that the effect of physical defects is negligible for isotropic metals, This assumption appears consistent with most of

Jan 1, 1959

By G. T. Pruitt, T. L. Irby, P. B. Crawford, H. Ferrell

In water flooding peripheral, center-to-edge, line-drive or water-encroachment patterns the question has arisen, "when should a producing well be converted to a water-injection well?". It is realized that, if the producing well is shut in when water breakthrough occurs, some oil could be left in an unswept area. Yet, operation to high water-oil ratios may require processing much additional water. If a well is shut in, "where should the allowable be transferred?". A review of the literature indicates that very few data are available to the engineer to assist him in answering these questions. It is the purpose of this paper to present information which may be of value in selecting the flooding technique and the injection and producing wells and in scheduling injection and production rates. Certain phases of these problems can be studied in the laboratory. The Potentiometric model is well suited for studying many waterflooding problems. This model assumes that steady-state flow exists, that the mobility ratio is equal to one and that gravitational effects are neglected.'-' The three-phase sand model also has been recognized as an effective means for studying certain reservoir problems. Both models were used in making the study reported here. This paper discusses seven cases utilizing various waterflooding techniques. Data for the first five cases were obtained on the potentiometric model. Data for Cases VI and VII were obtained by constructing and flooding an unconsolidated sand pack (a three-fluid-phase system) and by determining the swept area and cumulative oil recovery for various types of operations. APPARATUS AND PROCEDURE The potentiometric model reservoir was 30 in. long X 10 in. wide by about 1/2 in. deep. Four wells were equally spaced in a line array along the lateral center line. (See Fig. 1.) Well No. 1 initially was an injection well for each of the patterns reported. The cases studied with the potentiometric model and sand model are described herein. The laboratory sand model reservoir was a 30- 10-in. rectangular Lucite vessel packed with sand to a depth of about 0.65 in. Four wells were equally spaced in a line array along the lateral center line. The reservoir material was an unconsolidated sand into which the reservoir fluids were mixed to yield fluid saturations of 55 per cent oil, 25 per cent water and 20 per cent gas. The water was added to the sand and the material mixed, after which the oil was added. Kerosene and water, the fluids used, gave a viscosity ratio of 1.64:1. In packing the reservoir, care was taken to assure constant fluid saturations and constant porosities. A new mixture was prepared for each run. During water flooding, a colored water was injected by a constant rate pump. The injection rate was 1.1 B/D/ft of sand thickness. For this series of tests, each of the producing wells was open to the atmosphere and, as in the potentiometric model study, Well No. 1 initially was an injection well for each of the patterns. KESULTS OF POTENTIOMETKIC MODEL STUDlES Two cases (Cases I and 11) involving equal pressure injections were studied, with the following results. Case Water injection was initiated at Well No. 1; the producing wells (Nos. 2, 3 and 4) were operated at constant and equal bottom-hole pressures. When water broke through at Well No. 2 and achieved the selected water-oil ratio, Well 2 was converted to a water injection well, resulting in two injection and two producing wells. The injection pressures at Wells 1 and 2 were maintained equal and constant; pressures at the producing wells were held equal, but they were lower than those at the injecting wells. A similar process was repeated when water broke through at Well No. 3. The flood was terminated when

By L. D. Jaffe, F. W. Cotter, E. Cordon

The hardenability of titanium-base alloys was studied by metallographic examination and hardness survey of Jominy specimens end-quenched from the B range. Analyses of the data led to the equation log J = -0.57 + 0.25 @ct Fe + pct Mn + pct Mo) + 0.19 @ct Cr) +0.16 @ct V) + 0.03 @ct Zr). Here J is the distance, in sixteenths of an inch, from the quenched end of a Jominy hardenability specimen in the position of peak hardness, for material quenched from the B range. This equation fitted the experimental data with a standard deviation of approximately 0.29. The effects of the elements Al, Sn, W, Cu, Ni, B, C, N, 0, and H, and of pain size, were not statistically significant or not practically significant. A check against hardenability measurements in the literature showed agreement within the stated standard deviation. The equation should be useful in estimating hardenability of new or modified titanium alloys. HARDENABILITY in a titanium-base alloy is the ability of the alloy to retain the B structure on quenching. An alloy with high hardenability will retain the /3 structure even when cooled relatively slowly from a temperature at which B or P plus a is stable. A low hardenability material will retain P only if quenched extremely rapidly from the range of p or 0-plus-a stability, or will not retain it at all, at room temperature. High hardenability is desirable in titanium alloys to be heat-treated to high-strength levels. Its value is by no means limited to large section sizes. With high hardenability, a material can be solution-treated and cooled at a variety of rates, either to give high strength directly or, more generally, to give a soft ductile condition from which high strength can be obtained by subsequent aging. With low hardenability, high strength can be obtained, if at all, only by very rapid quenching, and there will generally be little increase in hardness on subsequent aging; an alloy of this type is limited in its applicability. On the other hand, alloys of very low hardenability have some advantages in weldability; essentially, they are always in the annealed condition, after welding as well as before. For commercial alloys, hardenability data are usually available, in the form either of property data after cooling from the solution temperature at various rates, with or without subsequent aging, or of results of a standard hardenability test, such as that originally developed for steels by Jominy and Boegehold.' When modifications of an available alloy are considered, or preparation of new alloy compositions, it would be Very convenient to be able to estimate the hardenability of the new material without having to make and test it. A method of estimating hardenability of titanium alloys from their composition was suggested by one of the authors some time ago, on a preliminary basis, utilizing scattered data found in the literature.' It seemed worthwhile to carry out a systematic experimental study of the effect of composition upon hardenability. EXPERIMENTAL PROCEDURE Approximately fifty heats of various compositions, weighing 8 to 10 Ib apiece, were melted in a small inert-gas tungsten-arc furnace with water-cooled copper walls. The starting material was 110 Brine11 titanium sponge, with high-purity metals added for alloying. Each heat was bottom-poured under vacuum through a molybdenum burnout strip into a cold graphite mold, to form an ingot approximately 4-1/2 by 3-1/2 by 3 in.* From each ingot were cut *The material was melted and cast by Pitman-Dunn Laboratory, Frankford Arsenal, to whom the authors must express their thanks. two pieces 4-1/2 by 1-1/2 by 1-1/2 in. These were forged, at temperatures adjusted to the composition, into 1-1/4-in. rounds, from which standard 1-in.-diam hardenability specimens3 were machined. A number of small samples were also prepared from forged materials of each heat, annealed, quenched from various temperatures, and examined metallographically. The P-transus temperature was determined by observation of the degree of resolution of primary a in these pieces. samples for chemical analyses were also taken from the forgings. One hardenability specimen of each heat was solution-treated for 1 hr approximately 50°F above the measured transus temperature, and the other for 1 hr approximately 250°F above the transus. (An additional hour was allowed for the specimens to reach furnace temperature.) These are not necessarily the temperatures that would be selected for

Jan 1, 1964

By A. J. Conelius, D. P. Sobocinski

This paper presents a correlation for predicting the behavior of a water cone as it builds from the static water-oil contact to breakthrough conditions. The correlation is partly empirical and involves dimensionless groups of reservoir and fluid properties and of production and well characteristics. The groups were deduced from the scaling criteria for the immiscible displacement of oil by water. The correlation is based on a limited amount of experimenfal data from a laboratory sand-packed model and on results from a computer program for a two-dimensional, incompressible system. Because the correlating groups are dimensionless, they can be used to estimate the performance of water coning cases not specifically considered in the correlation. However, despite its dimensionless nature, the correlation is not completely general and will not provide meaningful estimates of cone behavior in many situations. INTRODUCTION AND BACKGROUND The production of water from oil wells is a common occurrence which increases the cost of producing operations and may reduce the efficiency of the depletion mechanism and the recovery of reserves. We will deal with one cause of this water production, namely, coning. The coning of water into a producing well is caused by pressure gradients established around the wellbore by the production of fluids from the well. These pressure gradients can raise the water-oil contact near the well where gradients are most severe. Gravity forces that arise from fluid density differences counterbalance the flowing pressure gradients and tend to keep the water out of the oil zone. Therefore, at any given time, there is a balance between gravitational and viscous forces at points on and away from the completion interval. When the dynamic forces at the wellbore exceed gravitational forces, a cone of water will ultimately break into the well to produce water along with the oil. We can expand on this basic visualization of coning by introducing the concepts of stable cone, unstable cone and critical production rate. For instance, if a well is produced at a constant rate and the pressure gradients in the drainage system have become constant, a steady-state condition is reached. If, at this condition, the dynamic forces at the well are less than the gravity forces, then the water or gas cone that has formed will not extend to the well. Moreover, the cone will neither advance nor recede, thus establishing what is known as a stable cone. Conversely, if the pressure in the system is in an unsteady-state condition, then an unstable cone will continue to advance until steady-state conditions prevail. If the flowing pressure drop at the well is suffcient to overcome the gravity forces, the unstable cone will grow and ultimately break into the well. It is important to note that in a realistic sense, stable cones may only be "pseudostable" because the drainage system and pressure distribution generally change. For example, with reservoir depletion, the water-oil contact may advance toward the completion interval, thereby increasing chances for coning. As another example, reduced productivity due to well damage requires a corresponding increase in the flowing pressure drop LO maintain a given production rate. This increase in pressure drop may force an otherwise stable cone into a well. The critical production rate, well known in the literature, is the rate above which the flowing pressure gradient at the well causes water (or gas) to cone into the well. It is, therefore, the maximum rate of oil production without concurrent production of the displacing phase by coning. At the critical rate, a built-up cone is stable but is at a position of incipient breakthrough. Numerous papers have been published on critical rates. Some of the better known of these include the work of (1) Muskat and Wyckoff,' who first dealt with the coning problem; (2) Chaney, et al,' who developed expressions similar to those of Muskat but who presented results in a conven ient-to-use graphical form (the "Sun" method); and (3) Meyer and Garder,b hose analysis is based on radial-flow formulas. One assumption in critical production rate analyses is that the cone has built-up to just before its breakthrough into the well. But, these analyses reveal nothing directly about the time it takes for the cone to build up to this incipient breakthrough position. Thus, water-free oil can be produced from a well for prolonged periods at rates above the critical rate before the well reaches the condition to which the critical rate applies. The published literature contains little on the rate of growth of a cone. Experimentally, Meyer and Searcy studied the rate of rise of a cone in a Hele-Shaw model.' Additional related work on water breakthrough and produced water-oil ratios in water driven reservoirs was reported by Muskat," Hutchinson and Kemp," Henley, et al,' and Stevens, et a1.B Theoretically, the basic coning equations for a water-oil system can be developed by applying the conservation of mass to each of the phases, relating flow velocities with pressure by Darcy's law, and relating pressures across water-oil interfaces by capillary pressure. With the usual boundaries at the well and reservoir limits, the solution of the resulting equations for the time behavior of a water-oil interface constitutes a free-surface, boundary-value problem. The shape of the boundary depends on the internal potential distribution, while this

Jan 1, 1966

By John D. MacFadyen

Subject paper unfortunately has some serious flaws negating the usefulness of the paper. The authors claim that sulfur is the major source of production problems in cement kilns. This is not the case. Sulfur is not a problem as long as the mole ratio of sulfur to alkali oxides is less than, or equal to, 1. This is attributed to the sulfur preferentially combining with the alkali oxides and not acting as a clogging agent due to the nature of the pre-heater vessels. Where the mole ratio exceeds 1, many methods are avail- able to eliminate or reduce the clogging problems such as using the preheater bypass or a precalciner with up to 100% kiln gas bypass. In non-preheater kilns, the presence of sulfates is hardly ever a problem anyhow. Thus, the level of sulfur in the fuel and raw material that might cause problems is not a fixed amount, but is predictable. The purpose of the paper is to discuss the economics of conversion of kilns in the Indonesian and Phillippine cement industries from oil firing to coal firing. This economic analysis has very little to do with the sulfur levels. Thus, the section of the paper on sulfates is actually rather meaningless. The economic analysis is also rather meaningless because the authors have failed to follow accepted economic analysis procedures by including interest charges. They have fallen into the trap of confusing financing with economic evaluation. When the accepted methods of economic evaluation are used, the return on investment increases to about 35%. In conclusion, the paper is not a meaningful contribution, and sadly, quite erroneous.

Jan 1, 1983

By A. S. Appleton, M. B. Bever

The stored and expended energies of an Au-Ag alloy deformed in torsion were investigated as functions of strain, strain rate, and temperature. At room temperature, the stored energy, measured by tin solution calorimetry, increased linearly up to an intermediate strain, above which it was nearly constant; at 78 °K the relation was linear up to fracture. Approximate values of the energy stored at 4 OK indicate a rapid increase below 78 OK. The energy stored by specimens deformed successively at 4o and 78oK changed slowly with increasing second strain from the curve for energy stored at 4 OK (measured after annealing at 78oK) to that for deformation at 78°K. The ratios of the stored to the expended energy at room temperature and 78 oK were unusually large. The additional amount of energy stored at the lower temperature is attributed mainly to an increase in the number and energy of dislocations. The stored energy as a function of strain rate at 4oK (measured after annealing at 78oK) increased to a sharp maximum over a narrow range of strain rates, whereas the expended energy changed only slightly. These effects are explained by the generation of point defects resulting from the enforced nonconservative movement of jogs in fast moving screw dislocations. The effect of straining successively at two strain rates at 4oK was also investigated. Stress-strain curves for 4o, 78oK, and room temperature and the results of micro examination of specimens deformed at these temperatures are also reported. THIS investigation is a continuation of a research program primarily concerned with the effects of variables on the energy relations involved in the deformation of metals. The variables investigated in earlier work have included strain, strain rate, temperature of deformation (room temperature and 78oK), and the type of deformation process. Most of this work has been carried out with Au-Ag alloys. In the investigation reported here, the deformation process was torsion, which had not been used previously in the program. The stored and expended energies involved in the deformation process were measured as functions of strain, strain rate and the temperature of deformation in the range 4" to 373" K. The microhardness and microstructure of deformed specimens were also investigated. The relation between stored energy and strain differs for different deformation processes.1,2 In general, the stored energy increases with strain and may attain a nearly constant value at large strains. This value and the rate at which it is reached, however, depend on the process of deformation. This dependence has been attributed, at least in part, to differences in the effective strain rate and rise in temperature of the specimen during deformation. The effects of the temperature of deformation on both the stored energy and the energy expended in the working process have been the subject of only a few investigations.3-6 Values of these quantities at low temperatures are of special interest as they yield information on point defects which, for many metals, is not obtainable at higher temperatures. The effect of the strain rate on the stored and expended energies has received little attention The strain rate has usually been measured only in relative terms, and hence the interpretation of its effect on the stored energy has been mainly comparative.

Jan 1, 1963

By E. T. Turkdogan

This paper deals with an analysis of the conditions leading to the formation of blowholes and surface and subsurface defects in cast low-carbon steels. The theoretical analysis of the problem is based on the concept of the occurrence of deoxidation reactions during cooling of liquid steel and during its solidification. The reaction equilibrium data are given on deoxidation of steel by carbon, silicon, and manganese. The details of the calculations are given on the simultaneous deoxidation of steel by silico-manganese additions to produce a desired level of deoxidation at certain residual concentrations. Based on an idealized model, an attempt is made to calculate the enrichment of solutes in the solidifying liquid entrapped within the interdendritic cells which are known to be less than 200 µ thick. Formulae are derived for the calculation of the change in the residual oxygen content of the enriched liquid steel, controlled by Si/Mn deoxidation. It is shown that for every particular initial silicon, manganese, and oxygen concentration in steel (as residuals in liquid solution at the beginning of solidification) there is a particular carbon concentration below which carbon monoxide, leading to blowholes or pinholes, is not expected to form. There are a number of independent variables which have a decisive influence on the formation of blowholes. For example, it is shown that the position of the curve depicting the critical relation between initial silicon and carbon content for suppression of the evolution of carbon monoxide) can be shifted to lower silicon or higher carbon levels by: increasing manganese content; decreasing oxygen, hydrogen, or nitrogen content; or increasing external pressure on the solidifying mass. FOR the production of sound castings it is essential to prevent the formation of interdendritic worm-holes or pinholes brought about by gas evolution during solidification. Another major problem encountered in solidification of ingots is the formation of surface defects. These problems are thought to be closely associated with the deoxidation reaction occurring in liquid steel during cooling and subsequent solidification. As the liquid becomes richer in impurities during dendritic solidification of steel, a series of reactions may occur in the liquid phase trapped within the branches of growing dendrite platelets. Because of the strong interaction between dissolved oxygen and impurities in liquid steel, the reactions most likely to occur are of the deoxidation type. However, inherent to the extreme complexity of the problem in question, numerous simplifying assump-

Jan 1, 1965

Several of the current concepts of brittle fracture involve consideration of, the existence of defects or flaws. Griffith 1 observed that the tensile strength of brittle materials was several orders of magnitude less than might be expected from the calculated strength of the molecular bonds. He was able to show that the stress concentration at the tip of an elliptical crack is sufficient to raise the local stress level many fold. He therefore proposed that real materials do contain such stress risers in the form of minute cracks and that this accounts for the rather large difference between theoretical and actual strengths of brittle materials. The degree of stress magnification depends to a great extent upon the orientation of the crack with respect to the general stress system, and to the general geometry of the crack. It is but a small step to extend the theory to include flaws and defects of other sorts which, though they may be less tractable mathematically than cracks, may still function as stress risers in a real sense in real materials. Brace 2 proposed that the application of the Griffith theory to rock material could be tested in two ways: "(a) by finding the orientation of cracks from which macroscopic fractures have developed and (b) comparing failure strengths from tests at different conditions of loading." In 1963 the author and coworkers at the Bureau of Mines, Twin Cities Mining Research Center, working on a problem involving relationships between strength, sonic velocity, and microstructure "eveloped an experimental technique to examine several somewhat similar questions; namely. does the frequency of occurrence of actual or potential stress risers dictate the relative strength of the material as proposed by Weibull;4 can actual flaws or defects in the rock structure be identified and related to strength and perhaps other properties in accordance with Griffith's theory; and is the anisotropic strength and elastic behavior of certain rocks related to the preferred orientation of these actual or potential stress risers? The experimental approach developed to answer these questions appears equally applicable to the testing of Griffith's theory as proposed by Brace. Basically the approach consists of a series of point-load tensile tests followed by petrofabric examination of thin sections prepared from the specimens in order to identify and apply a quantitative measure to microstructural defects which may have contributed to the failure process. In the point-load test, tensile stresses are induced by a compressive load applied to the center of a disc-shaped specimen by means of two opposing hemispherical indentors. Failure generally occurs as a single fracture parallel to the axis of loading and bisecting the disc. Because of the geometrical symmetrical the induced tensile stresses are symmetrical about the loading axis

Jan 1, 1967

By E. W. Parker

PROBABLY everyone is well aware that from April 1 to September 11, 1922, anthracite production was completely suspended; during those 163 days not one ton of coal was produced in the anthracite region. The production loss was about 30 million tons, and although production is now at its peak, there is no possible way by. which, within any short space of time, that deficiency can be made up. During that time the miners sacrificed in wages something over 100 million dollars. The anthracite companies paid out in cash, keeping their mines in condition to operate when mining should be resumed, something like 30 million dollars without taking in one cent of revenue. The tonnage of domestic sizes included in that lost output was about 21 million tons. The anthracite operators figured that between September 11, 1922, and March 31, 1923, they would possibly be able to produce about 60 per cent. of the tonnage that was mined the preceding year, that is, from April 1, 1921, to March 31, 1922. The problem then arose as to how that tonnage could be distributed equitably throughout the United States and Canada. We had in our records in Phila-delphia the distribution by communities, about 20,000 of them, to which anthracite had been shipped during the last five years, so that we were well posted as to what each community should be entitled to receive. We allotted to each of those 20,000 communities 60 per cent. of the tonnage that it had received during the preceding coal year, and we have endeavored to see that whatever tonnage we have been able to produce should be equitably distributed on that basis. It was a matter simply of voluntary cooperation by the anthra-cite operators who placed the distribution of their tonnage practically in the hands of the Pennsylvania Fuel Commission; the anthracite companies have almost without exception acceded to every request that we have made of them. When communities were reported entirely out of coal, a telegram or letter to the directors obligated to that community has resulted in some anthracite being shipped there, so that we have thus far kept the distribution on a fairly equitable basis. Prior to the suspension of mining operations, pre-liminary negotiations were carried on for the renewal of the wage scale, the operators thinking that it could be adjusted satisfactorily, and that the same method of procedure would be followed as during the 20 years succeeding the strike of 1902. At every termination of the wage agreement since that date, until last year, an agreement had been reached early in the season that mining operations should be continued, with the under-standing that any new agreement should be retroactive to April 1. At the meeting of the committees of anthra-cite operators and miners, on March 21, 1922, the opera-tors were presented with an ultimatum by the miners to the effect that unless an agreement were reached within ten days, mining operations would cease. That was protested against by the committee of operators as being unfair, not only to the operators and the public but to the men themselves. In spite of this protest the suspension occurred and, as you know, continued until September 11.

Jan 4, 1923