Search Documents

By F. I. Grace, L. E. Murr

The mechanical responses and residual defect structures in 70/30 brass and type 304 stainless steel following explosive shock loading and cold reduction by rolling have been studied. A distinct relationship was observed to exist between the residual mechanical properties and micro structures observed by transmission electron microscopy. Shock-loaded brass deformed primarily by the formation of coplanar arrays of dislocations and stacking faults at lower pressures, and twin-faults (deformation twins and €-martensite bundles) at higher pressures (> 200 kbar). The micro -structures of cold-rolled brass were characterized by dense dislocation fields elongated in the rolling direction. Stainless steel was observed to deform by the formation of dense arrays of stacking faults at lower shock pressures and twin-faults at high shock pressures (>200 kbar). Lightly cold-rolled stainless steel deformed similar to low Pressure shock-loaded stainless steel, but transformed to a' martensite in heavily cold-rolled stainless steel. Discontinuous yielding was observed for the heavily cold-rolled stainless steel, and stress reluxution in the weyield region for cold-rolled and shock -loaded stainless steel was interpreted as an indication of the ability of twin-faults and stacking faults to act as effective barriers to dislocation motion. A simple model for the formation of the planar defects and a' martetnsite is presented based on the propagating of Shochley partial and half-partial dislocations. A considerable effort has been expended over the past decade in an attempt to elucidate the response of metallic-crystalline solids to the passage of a high velocity shock wave (e.g., smith,' Dieter,2 and zukas3). While it has been possible to obtain relevant information pertaining to the residual defect structures and mechanical properties, there have been few rigorous attempts to draw a direct comparison between these structures and properties. In addition, numerous investigators have recently observed the occurrence of deformation twinning in shock deformed fcc metals (e.g., Nolder and Thomas,4 and Johari and Thomas5), but little attempt has been made to elucidate the mechanisms of formation of these defects. Comparative data for metals deformed by shock-loading and the same metals deformed by more conventional modes of deformation such as cold-reduction by rolling is also generally lacking. The present investigation therefore has the following objectives: 1) to examine the mechanical properties of some explosively shock loaded and cold-rolled fcc metals of low stacking-fault energy as a function of their residual substructures; 2) to present a simple model for the formation twin-faults and related defect structures in the low stack-ing-fault energy materials of interest (70/30 brass, ySFg= 14 ergs per sq cm; and 304 stainless steel, ySF = 21 ergs per sq cm); 3) to make some deductions with regard to the residual characteristics of dislocation and planar defect substructures in cold rolled and shock loaded 70/30 brass and type 304 stainless steel. In particular, it was desirable to characterize the residual hardening effects of particular deformation substructures. I) EXPERIMENTAL PROCEDURE Sheet samples of 70/30 brass (0.005 and 0.15 in. thick; annealed at 659°C for 2 hr) and type 304 stainless steel (0.007 in. thick; annealed 0.25 hr at 1060°C) of nominal compositions shown in Table I were cold-rolled in one direction only to produce reductions in thickness of 15, 30, 45, 60, and 75 pct in the brass; and 5, 15, 25, 35, and 45 pct in the stainless steel. Identical sheet samples in the annealed (unrolled) state were subjected to plane compressive shock waves to various peak pressures ranging from 0 to 400 kbar in the brass and 0 to 425 kbar in the stainless steel; and with a constant peak pressure duration of approximately 2 microseconds. A detailed description of the shock loading technique has been given previously.6 Tensile specimens 1.0 in. in length and 0.125 in. in width were cut from the cold-rolled sheets (tensile axis parallel to the rolling direction), and the shock-loaded sheet specimens. Stress (load)-strain (elongation) measurements on the tensile specimens were made on a Tinius-Olsen load-compensating tensile tester using a strain rate of 2.7 x 10-3 sec-1. Tensile tests were repeated at least twice, giving essentially the same results. Stress relaxation measurements in the preyield region were also made using an initial strain rate of 5.4 x 10-4 sec-1. In addition to tensile and stress relaxation measurements, Vickers microhardness measurements were made on all samples. A total of 100 microhard-ness readings were obtained for each specimen following a light electropolish to ensure uniform surface conditions for all tests. The hardness averages ob-

Jan 1, 1970

By D. J. Jr. McAdam

PART I. OUTLINE OF INVESTIGATION, DESCRIPTION OF MATERIAL AND METHODS RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent papers.1,2,3,4 In those papers references were also given to the work of Haigh in 1917.6 Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper.2 The salt water is Severn River water having a saline content about one-third that of sea water.

Jan 1, 1928

The House Committee of the Engineering Societies Building has lent to he members of the three welfare committees a room on the ground floor of the building where they can carry on some of their war activities. Two sewing machines and two knitting machines are installed there and ladies are invited to sew for the Foreign War Relief Committee and knit for the Emergency Committee, which is working for the 27th Engineers, a special mining regiment. The Emergency Committee, Mrs. H. Norman Spicer, Chairman, reports the formation of a committed of 21 members. The organization meeting was held March 7, and plans were made for future activities as follows: A letter was read from Mr. Ingalls asking for 72 sweaters, 72 helmets, 66 pairs of wristlets as well as 772 pairs of socks, 272 being for immediate delivery. To meet this request it was decided to secure the helmets and wristlets from the Navy League, and to undertake the making of the sweaters and socks ourselves. Accordingly Mrs. H. N. Spicer and Mrs. J. H. Devereux were empowered to buy wool in sufficient quantities, and woven material for the 72 sweaters, sending the bills to Mr. Ingalls, who had guaranteed the money from the Engineering and Mining Journal. This was attended to promptly, and the materials were ready for distribution to the committee on March 13. After considerable difficulty, knitting machines for the socks were discovered and the agent came to demonstrate them. Mrs. Spicer gave one to the Committee and Mr. Ingalls has guaranteed the money to buy two when the manufacturers can deliver them. Up to April 6, 130 pairs of socks, machine and hand-knitted, have been handed in-also 68 sweaters, 80 helmets and 90 pairs of wristlets. It has been calculated that it needs five women knitting behind each man at the front to keep him continuously supplied with knitted garments.

Jan 5, 1918

By E. F. Miller

The subject " Safe Timbering of Working Places in Mobile Loading" is one that requires an analytical study of the strata both above and below the coal seam as well as the characteristics of the coal seam itself. The projection or mining plan must be based on economic roof control in which the application of timber can be minimized without incurring cost increases in other phases of production. The several types of loading machines in common use today are not adaptable to the same projections or timbering systems. Consequently the type of equipment to be used must also be considered. For these reasons the writer does not believe that the problems of timbering in working places can be discussed without simultaneously considering economic production as well as the safety of men and the conservation of equipment. Prior to the introduction of loading machines as a substitute for the pick and shovel system of loading coal, the care and maintenance of the individual working places were generally the responsibility of the coal loaders who worked in them. Up to that time very few coal companies had developed and applied fixed and definite standards for timbering the working places in the mines they operated. It is common knowledge that mechanical loading of coal has had several false starts in the last twenty-five years and it is only in the last decade that it has developed to the stage at which we now find it. During this twenty-five year period the management of the more responsible companies have come to realize the tremendous importance of roof control in coal mining. From a safety viewpoint, the lack of roof control has been and still is responsible for more than a third of the industry's annual fatality experience. In recent years workmen's compensation and insurance rates have steadily increased while the profit margin has decreased almost to the point of elimination. From an economic operating viewpoint, the failure to properly control roof is quite often the most costly single phase of coal mining. Since the manufacturers of loading machine equipment have so improved their machines that normal care and maintenance can reduce to a minimum the time lost because of mechanical failure the production delays from other causes have assumed a far greater importance. Roof control in the broad sense and in the light of concentrated mining plans or projections that are adapted to mobile loading should be regarded as one of the major problems in the inseparable phases of production and safety of the workman and equipment at the working face. The subject of this paper cannot be treated properly unless what is said here is based upon the broad and fundamental problem of genera' roof control. The suc-cessful solution of a problem arising in any industry must have its origin in a complete analysis of the known facts or factors that pertain to it. The several illustrations

Jan 1, 1949

By A. H. Grobe, F. N. Rhines

THE constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conventional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitution of its alloys desirable. As a part of a program for the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram [ ] (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (143.5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

By E. M. Norris

DURING the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation;(5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol.

Jan 2, 1922

By H. W. Ahrenholz

Seven weeks of 1971 were devoted to a nationwide coal walkout resulting in lost production of some 70 million tons and leaving 1971 coal production at about 550 million tons. Compounding the problem, consumption of coal in 1971 by electric utilities rose by about 5% to 336 million tons. In the mean- time, numerous contracts were awarded for coal R&D including $24.8 million given by the Office of Coal Research to Bituminous Coal Research for the construction of a coal-to-gas pilot plant using the BIGAS process. Exports declined mainly due to Japan's decrease in steel production and to that country's increase in coal imports from Canada and Australia. The advances in equipment design and mining procedures made 1971 a noteworthy year. Introduction of the variable pitch I dipper, the trend toward wheeled vehicles, the greater use of scrapers in reclamation and battery-operated vehicles and oscil-mining, and the increased activity in the areas of ventilation and dust control were given widespread approval. There were also strides made in computerization, longwall mining, roof bolting, rock dusting, mine haulage and methane detection.

Jan 2, 1972

By William A. Kapp

INTRODUCTION Coal is being mined from beneath residential areas, structures, bodies of water and other surface features in the coalfields to the north, south and west of Sydney. The particular problems faced by mine operators in these areas vary considerably due to differences in the overlying strata, the variation in the depths of cover and also depend on the number of seams being mined. Detailed subsidence work first commenced in the Southern Coalfield in 1965 and is now being carried out over areas of extraction at roost collieries. The analysis of the results of the early investigations and of the work which continues in other areas has shown that there is a consistent relationship between subsidence and mine geometry and has led to a reliable empirical method for the prediction of subsidence. In addition, particular aspects of each of the studies in the Southern Coalfield results in a clearer understanding of strata movements and of the resulting subsidence. The features of a subsidence trough apply generally to all areas but the magnitudes of specific features vary according to the stratigraphy of the particular coalfield. The aim of the subsidence work is to quantify the effects of subsidence for a range of mining geometries and mining conditions to enable the maximum safe recovery of coal from beneath surface features. The importance of local subsidence investigations is becoming more evident to mine operators and to authorities or organisations with surface interests. The subsidence work also provides important information on the stabilities of pillars of coal which remain unmined between panels of extracted coal. These pillars are not extracted either because of poor mining or geological conditions, or because pillar extraction is not part of the particular mining operation. Subsidence studies over these coal pillars clearly establish whether the pillars have remained stable or have failed to support the overlying strata. With subsidence studies continuing over several years, it is possible to assess the stabilities of these pillars on a long term basis. BACKGROUND TO THE STUDY OF SUBSIDENCE Geographical setting Most of the black coal production in Australia comes from the Sydney Basin. The coal seams extend for approximately 350 km along the coast of New South Wales and inland for distances up to 150 km. The City of Sydney is located near the centre of the coastal extent of the Basin where coal has been mined at a depth of 900 m. The Sydney Basin is part of the Main Coal Province of NSW and is divided into several coal- fields. The Southern Coalfield to the south of Sydney contained 15 operating mines and produced 12.7 million tonnes of raw coal during the 12 months to June 1981. The collieries discussed later are shown in Fig. 1. The prominent topographical feature of the area is the Illawarra Escarpment which rises to 400 m above sea level, or 300 m above the coastal strip along the South Pacific Ocean. The escarpment is mainly sand- stone and the weathering of the cliff line has resulted in a covering of talus material at its base. Several collieries are located near the seams which outcrop along the escarpment. The city of Wollongong is located in a scenically attractive area on the coastal plain. The suburbs of Wollongong extend north along the coastline, south to beyond Lake Illawarra and west to the lower slopes of the escarpment. The Illawarra Escarpment forms the eastern boundary of the Woronora Plateau. On a regional scale the surface dips gently to the west and thus forms a watershed for the rivers, most of which flow in a general north westerly direction, sometimes forming steep gorges in the sandstone. These rivers join the Nepean and Hawkesbury River system and flow into the Pacific Ocean north of Sydney. Seven dam have been constructed over the Southern Coalfield (Fig. 1) and with one large dam further to the west, their stored waters provide the needs of the Cities of Sydney and Wollongong and the surrounding districts. A large part of the area affected by mining is the undeveloped bushland of the associated catchment areas. In general no special precautions have been required with respect to subsidence with the exception of the dam structures and stored waters. With the increase in coal mining activities and the expanding residential development south of the City of Campbelltown in the outer Sydney Metropolitan area, subsidence is becoming an increasingly important area of research. Structures which have been affected or considered are townships and extensive residential areas, buildings of historical importance, major tollways, and a high pressure natural gas pipeline. The subsidence effects of mining beneath natural features within national parks is coming under study as mining approaches these areas. Geological setting The coal seams of the Southern Coalfield lie within the Illawarra Coal Measures. They contain high rank coking coal used in the local steel industry and for export. The Bulli Seam is mined extensively through- out the Southern Coalfield with the lower Wongawilli Seam being second in importance with regard to coal production. The top of the Bulli Seam is taken to be the marker horizon between the Permian Coal Measures

Jan 1, 1982

By Walter Larsh

The Ruth orebody, so far developed, is roughly oval in plan, major and minor axes about 1600 ft. (487 m.) and 1200 ft. (365 m.) respectively, average thickness about 120 ft. (36 m.), and with a general dip of about 15° to the northwest. According to the generally accepted theory, the ore is a secondary enrichment of the porphyry due to leaching in situ by meteoric waters. Copper occurs as chalcocite, chalcocite coating pyrite, and a little chalcopyrite. The leached zone, or capping, covering the ore varies in thickness from 110 to 540 ft. (33 to 164 m.), average about 410 ft. (124 m.). The ore is blue gray in color, and the capping, light yellow to brown. Ore was first discovered in quantity in the workings from the Ruth shaft, now caved. Further development work was done by churn drills, and the outline of the orebody, as stated above, determined in this manner. Drilling is still being carried on. The porphyry area is entirely surrounded by sedimentaries, lime-stones and shales; and, in so far as the underground workings have shown, the porphyry' itself, the sedimentaries near the contact, and the country underlying the ore (igneous or sedimentary) is very soft, heavy, and in places swelling ground. All openings have to be carefully and stoutly timbered, and, after once driven, they have to be constantly eased off and repaired. The mine is at present served by two shafts, the Star Pointer, the main working shaft; a vertical, and the Ingersoll, an incline used for waste and material. The two shafts are about 2600 ft. (792 m.) apart, connected on the 500 level; a connection is now being driven on the 600 level. (Dec., 1917. This connection is now completed.) The 300 level, which is finished, and the 400 level which is nearly completed, are accessible only from the Ingersoll and connections with the 500 level.

Jan 1, 1918

The editorial expenses for the preparation of the manuscript of the second edition, as for the first, were provided by grants of the Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME ; the Seeley W. Mudd Memorial Fund again sponsored the publication of this volume. The companies and research or educational institutions with which the authors, reviewers, and editors are connected also contributed much to the writing and editing of this book through their generous donations of time and travel and office expenses. And finally, the authors and others have given countless hours of their own time with no recompense but the satisfaction of a job well done. In order to give credit to the companies or educational institutions which made it possible for the members of the Editorial Board to devote considerable time to the revision of this book, the names of these members and their affiliations are recorded here as follows W. O. Philbrook, Carnegie Institute of Technology M. B. Bever, Massachusetts Institute of Technology H. B. Emerick, Jones and Laughlin Steel Corporation B. M. Larsen, United States Steel Company A number of individuals suggested desirable changes in the book before rewriting was started. Almost all manuscripts were gone over critically by reviewers, and the resulting criticisms led to the correction of errors and omissions and greatly contributed to the accuracy and completeness of the text. Other people have supplied additional data or illustrations or assisted in other ways. While some of these contributors must remain anonymous because they are not known to the Editors, the cooperation of the following individuals is gratefully acknowledged: R. D. Allen, Republic Steel Corporation, Chicago Isadore Amdur, Massachusetts Institute of Technology Mary Baeyertz, Armour Research Foundation S. P. Bahmer, Republic Steel Corporation, Massillon E. C. Bain and Associates, United States Steel Company, Pittsburgh C. W. Briggs, Steel Founders' Society of America H. W. Briske, Wisconsin Steel Works

Jan 1, 1951

By R. Q. Shotts

Nitric acid oxidation rate analyses of three coals, previously studied microscopically by the Bureau of Mines, revealed three components. Relative quantities agree with those found for the four components given by the Bureau and results are consistent with current ideas of coal constitution. Possible multi-component composition for bright coal and a reactivity-rank relation are suggested. THE physically dissimilar components of bituminous coals often are easily recognized mega-scopically. Under the microscope, reflected light or light transmitted through thin sections reveals the presence of the different components, even when these are intimately mixed. Optical methods for the quantitative estimation of the relative abundance of the various components, both by means of thin sections and by particle count, have been fully described.'. ' It has long been recognized that there are chemical and physical differences between the various petro-graphic components of bituminous coals, although analytical differences usually are small.:'. ' Only in the case of fusain have chemical differences been used for quantitative determination of a component. C. C. Hsiao and associates, at the Mineral Industries Experiment Station of the Pennsylvania State College, have described a method of analysis which is based upon the differences in the rate of nitric acid (8N) oxidation, fusain, and the other components of coal."," The reproducibility of their method and its applicability in checking microscopic determinations of fusain content have been supported by several independent investigations.'. " The writer has proposed the use of differences in oxidizability for the estimation of other components." "' The results of the oxidation of whole coals and of float-and-sink fractions of coals were reported. In most cases the plots of the logarithms of the percent dry, non-fusain, organic residue from oxidation, against time, revealed the presence of at least two distinct components. Both components appeared to oxidize according to a first order law, but the reaction constants for the components were distinctly different. One or more of the dull density fractions were found to contain but one component, and some of the lower rank coals oxidized in such a way as to suggest the presence of three components. A suitable way to check the identity and significance of the components delineated by oxidation would be to analyze a sample of coal both by the nitric acid oxidation procedure and by a microscopic method. The writer was wholly unfamiliar with either of the microscopic techniques commonly used, and to make such a comparison it was necessary to rely upon microscopic analyses made by someone else. It is hoped that some laboratory which is equipped to make both types of analyses will some day make them upon identical samples. During the past 20 years, four Alabama coals have been analyzed petrographically and the results published by the United States Bureau of Mines. They are: 1—Flat Top mine, Mary Lee bed; 2—Empire mine, Black Creek bed; 3—Wylam No. 8 mine, Pratt bed, all in the Warrior field; and 4—Soot Creek mine, Fairview bed, in the Coosa field."-" Of these, only the Flat Top mine is still operating. Because of the closing of these mines, it first appeared necessary to rely upon the indirect and unsatisfactory procedure of sampling the beds in other mines located as near to the closed mines as possible. Upon investigation, however, it was found that the Bureau of Mines still had, in storage, the very same samples which had been used in the published petrographic studies. The Bureau very generously furnished about 2000 g each of the Pratt, Mary Lee, and Fairview bed coals, largely lumps but with some fines. The blocks of coal, when received, still were covered by the paraffin coating which had been placed on the polished surface, in the case of the Mary Lee coal almost twenty years ago. Procedure The procedure for oxidizing the coal sample and removing the alkali-soluble humic acid has been described. In the present study, oxidation periods of 1/6, 1/3, 1/2, 3/4, 1, 2, 3, and 4 hr were used. All oxidations were made in triplicate. After the paraffin had been removed in boiling water and the coal washed carefully with cold benzene, the entire sample of approximately 2000 g, obtained from the Bureau of Mines, was crushed to pass a No. 4 sieve. About 200 g of this material was pulverized to pass

Jan 1, 1954

By J. H. Brophy, J. Wulff, H. W. Hayden

The mickel-activated sintering of tungsten occurs in two stages of densification. A kinetic analysis of the second stage has been based on an appropriate model of the process. As in the first stage, the rate-controlling mechanism for the second stage is also the solution of tungsten in the nickel carrier phase. The transition from the relatively rapid first-stage results from the spherozdization of pores and the initiation of grain growth. Finer grain size due to higher-nickel content leads to more rapid and higher degrees of densification 1 HE sintering of tungsten is accelerated by small additions of nickel, cobalt, and iron.' Experimental evidence in detail has shown that nickel-coated, hydrogen-reduced tungsten powder may be sintered to more than 90 pet of theoretical density at l100o C.2, 3 Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the "solution-precipitation" step postulated when the carrier phase is a liquid,4 although in the Ni-W case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in microstruc-tures at the temperatures under consideration. It has been shown that this stage corresponds to a process which is rate controlled by a phase boundary reaction.3 More recent evidence has been presented5 showing that after the initial rapid stage of sintering, densification continues in the final stage but at a slower rate, although no mechanism for this stage of densification was defined. An analysis of later stages of densification in solid state sintering has been presented,6 but it is not directly applicable in the present case of activated or carrier phase sintering. It is the purpose of this investigation to study the final stage of nickel activated tungsten sintering in greater detail The effect of varying nickel content has been examined, and a possible kinetic mechanism defined. EXPERIMENTAL PROCEDURE AND RESULTS Commercial hydrogen-reduced tungsten powder from Wah-Chmg Corp., having a nominal particle size of1 µ and a B.E.T. specific surface area of 5500 sq. cm per g was mixed with aqueous solutions of hydrated nickel nitrate in proportions sufficient to produce nominal compositions of 0.25, 1, 3, and 5 wt pet Ni. This solution was then evaporated to dry-ness at approximately 150" C for 15 hr. Following evaporation, the resulting powder cake was broken with a mortar and pestle and reduced in hydrogen at 800oC for 1 hr. Following reduction, the powder

Jan 1, 1962

By D. H. Davis

HAND picking was the earliest form of coal preparation, first practiced to improve the outward appearance of the coal being loaded and to remove any pieces that might appear objectionable to the buyer. It is still extensively practiced on the plus 1-in. sizes and particularly on the plus 4-in. and larger sizes. The percentage of ash reduction that can be obtained by hand picking depends entirely upon the amount of free impurity occurring in the coal. In a particularly dirty seam, where a considerable quantity of rock occurs with the coal as mined, hand picking produces sizable reductions in ash. If the coal is prepared clean at the working face hand picking is a final check; in some cases, on the smaller sizes, it is practiced only to show that an effort is being made to prepare a clean product. Because of the variety and different methods of handling coal, the early plants were not always adapted for e5cient hand picking. At most mines an attempt is made to - remove the visual impurities at one or more of the following places in the surface plant: (1) in the tipple during screening; (2) on picking band, belt, or shaking conveyors; (3) during the loading of the coal as it goes into the railroad car. Whatever the physical arrangements of the plant may be, the usual practice is to run the coal over the screen, picking table or boom at such a rate that each piece of impurity is exposed to the view of the picker. Coal should be uniformly sized and spread out on the table so as not to exceed one particle in depth. The flow should be even in tonnage and the speed of travel should be from 30 to 60 ft. per minute and not exceed 80 ft. per minute. The dirtier the coal, the slower the speed required for a fixed number of pickers. Actually, picking capacity depends on the number of particles per minute that can be picked out and rejected. The percentage of impurity removed is determined by this and the average weight of piece rejected. Handling a mixture of sizes from nut to the largest lump over the same picking table or conveyor is not conducive to efficient separation by hand picking because the lump hides the smaller impurities. Picking tables should not exceed 5 ft. in width, so that a picker on either side will be able to remove impurities from the center of the table. Guards usually are placed at the side of the screen, boom or table, to allow the pickers to stand close enough to remove the impurities without too long a reach.

Jan 1, 1950

By T. Guilford Smith

In presenting the subject of " Armored Turrets for Coast Defense " to this Institute, I am indebted to the Gruson Ironworks, a company incorporated under the laws of the State of New York, for valuable information, model and plans, by which I hope to make clear the construction and peculiar merits of this class of gun-protection. I wish it understood, however, that this is not an undeveloped and untried inventor's ideal, but an advanced and fully perfected system, which has long since passed the experimental stage and has been adopted by most of the foreign governments, after years of extensive experimenting and the expenditure of millions of dollars. The present seems an appropriate time to present the matter to the scientific public, since, for the first time, it is possible to produce these turrets in this country, of American material, and made by American workmen, owing to an agreement entered into between the Gruson Iron-works and the Fried. Krupp Grusonwerk, of Magdeburg-Buckau, Germany, where they have hitherto alone been manufactured. Although its full development and present perfection have been attained at the German works, it may be of historic interest to state that the first idea of using a rotating protected platform for large guns originated with Mr. Theo. Ruggles Timby, a native of the State of New York, who filed a caveat in 1843 for a " metallic revolving fort, to be used on land or water, and to be revolved by propelling engines located within the same and acting upon suitable mechanism." This was followed in 1862 by the issuance to Mr. Timby of two patents (No. 35,846 and No. 36,593) covering the ideas described in his caveat of 1843. The first practical application of this system was made on the " Monitor," of Civil War fame, Mr. Timby receiving $10,000 for two

Jan 1, 1901

The Cuajone and Toquepala copper projects are located in the extreme southern area of Peru. Since 1960, Southern Peru Copper Company has operated the Toquepala open -pit mine, flotation mill, 110 smelter, townsites, power plants, and railroad. Toquepala and 10, the smelter and port location, are connected by a 110-mile-long (176 lun) railroad. Much of Toquepala's infrastructure has been used for the Cuajone project. Cuajone, at an elevation of 11,400 ft (3475 m), required five standard-guage railroad tunnels with a combined length of 17 miles (27.2 km) to connect with Toquepala so concentrates could be shipped to the no smelter. The total cost of Cuajone is estimated at $726 million for a designed annual capacity of 180,000 tons of copper, equivalent to about $4,000 per ton of installed production capacity. This relatively low cost per ton, by today's standards, has been made possible through the use of the 110-to Toquepala railroad, the ability to expand the 110 copper smelter, and other favorable factors. To mine the 468 million tons of copper sulfide or e at a grade of 1.0% copper, approximately 24 1 million tons of waste were stripped- before mining of ore to supply the new Botiflaca 45, 000 ton per day concentrator. The mining rate must exceed 300,000 tons of waste plus ore per day to maintain the 45, 0 00 tpd sulfide ore milling rate which was to be reached at the end of 1976. Waste stripping is done with 15 cu yd electric shovels and 120 -ton trucks. Ore mining is done with 8 and 9 yd shovels. A railroad connects the pit with the 60 in. by 89 in. Allis-Chalmers gyratory crusher. Side-dump railroad cars of 50.cu yd capacity dump onto a 0 16 ft 9 in. long (5. 1 m) grizzly inclined at 40º with 7 to 8 in. (178 to 203 rnrn) bar spacings. The grizzly is divided into two 22 ft 4 in. (6.8 m) wide sections and two side -dump railroad cars discharge simultaneously into the 150-ton capacity dump pocket. A Barco rock manipulator is used for breaking or removing oversize from the dump pocket. The bin receiving the grizzly undersize has a capacity of 5,000 tons, and the pocket beneath the crusher holds 900 tons. Each is equipped with an 84 in. apron feeder, which feeds a 60 in. (1.52 m) conveyor belt to the 150,000 ton coarse ore stockpile, where the ore is distributed by a 72 in. (1. 83 m) tripper conveyor. The 45, 000 live tons in the coarse ore stockpile are reclaimed by twelve 48 in. (1. 22 m) apron feeders. Maintenance on the crusher eccentric is made easy by an eccentric

Jan 1, 1978

By C. M. Loeb, T. E. Norman

THE use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies' of the factor sgoverning their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. THE DEVELOPMENT OF A SUITABLE WEAR TEST A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed, to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1,2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1947

By G. R. Rigby

Used basic brick taken from copper anode furnaces, reverberatory furnace roofs, md copper converters have been examined by chemical analysis, petro-graphical examination, and X-ray diffraction tech-niques. In the anode furnace roof, brick absorb copper and copper oxides, whilst in the reverberatory roof, iron oxide with smaller amounts of alumina and silica are absorbed. Chemical reactions in the converter are most complex since the brick absorb both a copper-copper oxide slag and a fayalite-magnetite slag. CHANGES taking place in basic brick after use in copper smelting furnaces have received attention from C. Burton Clark and J. Spotts Mc Dowell,' who examined brick taken from copper converters, and by G. R. Rigby and B. G. Hamilton' who examined brick from copper anode furnaces. This paper describes the changes taking place in basic brick from all types of copper smelting furnaces and discusses the major reasons for lining wear. A) METHODS OF EXAMINING SAMPLES A variety of used brick have been taken from the following positions in various furnaces, a) roofs, reverberatory arches, and bottoms of copper anode furnaces, b) roofs of copper reverberatory furnaces and c) the tuyere line and end walls of copper converters. The method of examination was standard in that brick were first measured and the extent of wear-back computed. They were next sawn in two by a central cut vei-tical to the working face to enable the freshly cut surfaces to reveal any zonal changes and cracks, both of which usually ran parallel to the working face. Each well-defined zone was then sampled for a) chemical analyses, b) petrographical studies using transmitted and reflected light techniques under the microscope, and c) X-ray diffraction studies on powdered samples. From the data accumulated, changes taking place in a variety of

Jan 1, 1962

By Russell C. Flemming

The aim of this Source Book has been to bring together in concise form information on the wealth of technical literature on mining and geology issued by the bewilderingly many state bureaus, federal bureaus, technical societies, trade associations and other noncommercial agencies in the United States. The effort has been made to include the navies of all the noncommercial publishers of such technical literature, to indicate where and at what price the articles may be obtained, as well as to give with as much detail as space permits specific information on individual papers. The thought has been to put the information particularly in the hands of the younger members of the profession, who may not yet have had the wide contacts with this literature that they will need in later life. Several factors have interfered with the complete attainment of the original intention. Undoubtedly some agencies that properly have a place in these pages have unintentionally been omitted; many agencies canvassed were omitted as not having literature of direct concern here; in other cases some. of the needed information was lacking; and the limitations of time and space have bounded the scope of the compilation.. Except in one or two cases, only publications prior to July, 1932, are included here, and from that standpoint the book is necessarily incomplete, as additions are continually being made to the files of literature on these subjects. Individual titles have been listed whenever possible but where an agency has collected a great mass of published material only most important titles, and a general review of the scope of the works, can be made. This results in penalizing, in a way, bureaus such as the U. S. Bureau of Mines and the U. S. Geological Survey, which have voluminous and vitally important works in the fields covered, because space commensurate with that volume and importance cannot be allowed. In any event, in such cases, a complete catalog is issued periodically and repetition is superfluous. The space

Jan 1, 1933

By J. S. Hegwer, P. M. Dunlap

An improved acid for the treatrrzent of sulfate-con-raining limestones and dolomites is described. The acid is designed to reduce he reprecipitation of dissolved calcium sulfate and the possibility of plugging permeable flow channels. In addition, this improved acid has a much lower reaction rate than that of regular acid; the advantages of a "retarded" acid are obtainable. Field testing of the acid has shown it suitable for use in sulfate-containing formations. Substantial improvements in productivity generally resulted. INTRODUCTION Acid treatments of limestones, dolomites and other formations bearing carbonate deposits are frequently unsuccessful when the calcareous formation contains sulfate, either as anhydrite (CaSO,) or gypsum (CaSO4. 2H2O). Preliminary dissolution in acid followed by redeposition of calcium sulfate appears to be a major factor contributing to poor well performance after acidizing. The precipitate is usually the gypsum form of calcium sulfate, but in higher temperature formations it may be anhydrite. The freshly precipitated crystals are nearly always very small and needle-like. They may occupy a gross volume many times that of the original anhydrite crystals and will obviously constitute an impediment to flow through newly enlarged flow channels. It is believed that the redeposition problem is most severe when anhydrite lines the fracture systems and large pores which supply the effective permeability of a formation. Microscopic inclusions of calcium sulfate also present large sulfate surface areas for dissolution in acid. In either case, great amounts of calcium sulfate may dissolve before the acid can be spent on formation carbonates. For regular spent acid (originally 15 per cent hydrochloric acid) the precipitate could be as much as 270 Ib gypsum/1000 gal acid. Two techniques have been applied by the industry for reducing sulfate plugging during acidizing. The method'.' commonly employed in the field is the attempted removal of a quantity of regular treating acid before it has reacted completely with the formation. This is practiced because the solubility of calcium sulfate is greater in a solution that is still acidic than in one which has been largely spent on the formation rock. The chance of precipitative plugging is therefore reduced if the withdrawal is successful. However, it is often impossible to get the acid out of the formation before precipitation occurs. A second possible method, which at first glance appears practical, involves addition to the acid of sequestering agents which form strong soluble complexes with calcium ions. These chemicals do increase the "solubility" of calcium sulfate in fresh acid, but to a lesser extent in spent acid. The sequestering agents have, therefore, proved unsatisfactory because the amount of sulfate eventually deposited from the spent acid may be greater than that from regular acid. Another logical approach to the problem of calcium sulfate reprecipitation is the prevention of the initial dissolution of calcium sulfate by the common ion effect. This may be accomplished by adding a soluble calcium salt to the fresh acid. The use of calcium salts in treating acids is not entirely new. An earlier suggested use of a soluble calcium salt in hydrochloric acid apparently failed to recognize the full extent to which the solubility of calcium sulfate could be suppressed. The present study extends this earlier work and adds certain improvements toward the development of a practical anti-anhydrite acid. LABORATORY DEVELOPMENT Calcium Sulfate Solubility Table 1 shows the results of a laboratory study performed to establish the effect of calcium chloride concentration on gypsum solubility. Because of the strong tendency of calcium sulfate to form supersaturated solutions, accurate solubilities are difficult to determine. These solubility data probably are reliable to within ± 15 per cent. The solubility of calcium sulfate in 15 weight per cent hydrochloric acid increases with increasing temperature. This trend is also followed in hydrochloric acid which cantains calcium chloride. This is contrary to the solubility behavior of calcium sulfate in water, wherein the solubility decreases with increasing temperature.

By G. H. Bruce, C. E. Williams

The trend toward deeper drilling, together with the attcndant increase in power requirements for circulation of the drilling fluid, has emphasized the need for a critical examination of the factors affecting the removal of bit cuttings from the hole by the drilling fluid. The ability of drilling fluids to lift cuttings is called their carrying capacity. A series of laboratory and field experiments has been conducted to determine the minimrim annular velocity necessary to remove cuttings, and to investigate the effects of properties of drilling fluids on their carrying capacities. Consideration of the results of these experiments led to the following conclusions: 1. Turbulent flow in the well annulus is most desirable from the standpoint of cutting removal. 2. Low viscosity and low gel are advantageous in removing cuttings. 3. Increase in mud weight is effective in increasing carrying capacity. 4. The carrying capacity is higher when the pipe is rotated than when it is not. 5. If turbulent flow can be maintained, an annular velocity slightly higher than the slip velocity of the largest cuttings to be transported should keep the bore hole clean. This implies velocities of 100 to 125 ft per minute rather than the presently used 175 to 225 ft per minute. INTRODUCTION Power Savings by Reduction of Annular Velocities A large portion of the power expended in drilling operations is consumed in circulating the drilling fluid. An important factor in establishing the rate of mud circulation is the minimum velocity in the annulus necessary to remove bit cuttings. Empirically, it has been found that average annular mud velocities of about 200 ft per minute will remove cuttings. It was not definitely known, however, whether annular velocities of about 200 ft per minute were just above the minimum necessary to remove cuttings, or whether such velocities could be materially reduced without sacrifice of the ability of the mud to remove cuttings. It is apparent that if annular velocities could be reduced without impairment of cutting removal, a considerable saving in power requirements would result. Need for Research on Carrying Capacity The ability of a drilling fluid to transport cuttings is called its carrying capacity. Although it has been recognized that the carrying capacity of a mud is affected by mud properties such as viscosity and density1,2,3,4 there have been various views in the industry as to the effects of these mud properties on carrying capacity. The economic importance of the problem of carrying capacity and the scarcity of information on the subject indicated that research on the problem was needed. THE FACTORS AFFECTING CARRYING CAPACITY Qualitative Determination of Factors The mechanism of cutting transport is closely related to that involved in the separation of material by settling processes. A considerable amount of research has been done on settling problems, and discussions of sedimentation theory can be found in standard texts.5,6 Consideration of the information available from these sources, together with consideration of the mechanism of cutting transport, leads to the conclusion that the factors affecting carrying capacity are the dimensions of the system, the physical properties of the cuttings. and the physical properties of the drilling fluid. system Dimensions and Their Effect The dimensions of the fluid circulating system of importance to carrying capacity are the bore hole size, drill pipe size, pump capacity, and pump speed. These dimensions determine the annular velocity of the drilling fluid. Physical Properties and Their Effects The physical properties involved in the interaction between mud and cuttings are the density and shape of the cuttings and the density, viscosity and gel strength of the drilling fluid. The effect of the density factor on carrying capacity is fairly obvious; high density difference between cuttings and fluid results in a low buoyant force and therefore decreases carrying capacity. The effect of cutting shape is less obvious. Although

Jan 1, 1951