Search Documents

By Ashbel Welch

Gentlemen of the American Institude of Mining Engineers.—As you well know an application is about to be made to Congress, by the American Society of Civil Engineers, for the appointment of a cornmission composed of persons skilled in the production and use of iron, steel, and other structural materials, whose duty it shall be to test the strength, elasticity, and other quatities of such materials ; not simply the substances used as such, but the members of large structures composed of such materials, of the forms and sizes in which they are actually used. As I understand, the papers that will be read here to- night will have for their object to show the necessity for such tests, and therefore the necessity for the commission asked for. As the representative of the Society of Civil Engineers, I have to thank you, gentlemen of the Mining Engineers, for the great zeal with which yon have taken up this subject, and seconded the efforts of the Civil Engineers; or, perhaps I ought rather to say, initiated the efforts to get a suitable commission appointed to obtain most vitally important information which it is admitted on all hands we do not now posses. In drawing up the memorial to Congress, in connection with some of the ablest and best informed of our Society, and in all the discossions on the subject, I have been struck with the emphasis with which the confession is made, that so little is known of the strength of the larger-sized members constantly used in building structures of the magnitude which the present requirements of the country now demand. I presume the remarks made to-night will bring this out very prominently. This is no disgrace, for with the means here-

Jan 1, 1882

By Frank C. Appleyard

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other principal calcium sulfate mineral has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhydrous form of calcium sulfate (CaSO,) whereas gypsum is the dihydrate (CAS0;2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. However, of most importance is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaS0;Vi H,O) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advantage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which when mixed with water would form a putty that could be "plastered" on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of its quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term "land plaster" for ground gypsum has remained in use. Another cementituous material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered and it has today almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $500 million per year as illustrated in [Table 1].

Jan 1, 1975

By Stephen G. Dardaganian

Pore volume compresibilitieu measured in the laborutory on core .samples are reported for typical reservoir .sarrrl.rtorres at reservoir pressure. These cornpressibilities ore different for each reseriloir sample and cannot be correlated to porosity. The compressihilities are a1so functions of presslire. In recent years several authors have pointed out the importance of including pore volume compressibility of the reservoir rock in certain reservoir engineering calculations. Hall' showed that in calculating the hydrocarbon volume of an undersaturated reservoir from the production per unit change in reservoir pressure, the neglect of rock compressibility could, in the extreme case of low porosity rock, lead to results in error by a factor of two. Hawkinsl' and Hobson and Mrosovsky showed that both rock and interstitial water compressibilities must be included to achieve satisfactory accuracy in this calculation. Although rock compressibility is an important reservoir property in these calculations, very few data are available. Hall' made compressibility measurements on a few samples in a small pressure range. No other direct pore volume compressibility measurements have been reported. Geertsma' discussed the elasticity of reservoir rock but did not present any new data. In this paper, rock compressibilities suitable for reservoir calculations are reported for a variety of sandstones typical of U. S. reservoirs. The measurements were made through a range of pressures which is also typical of reservoirs. EXPERIMENTAL PROCEDURE Plugs 1 in. in diameter and 2- to 3-in. long were diamond drilled, 14 from cores from seven oil-bearing or potentially oil-bearing sandstone, one from a quarried sandstone, and another from a shallow, oil-free, pure orthoquartzite. The plugs were extracted in toluene, vacuum dried, and then weighed. The plugs were then saturated with kerosene and reweighed. This gave pore volume. They were then again extracted in toluene. vacuum dried, and jacketed in 0.004-in. thick copper foil. A short length of -in high pressure tubing led from the jacket. The jacketed sample was then saturated with kerosene and placed in the hydraulic pressure cell as shown in Fig. 1. Movement of the mercury slug showed the change in pore volume of the sample under a given pressure change. Temperature was about 72" F for all measurements. Before taking any measurements, the external pressure on the sample was raised to 10,000 psig and kept there for several hours. This formed the thin copper jacket around the plug. 7-he pressure was then removed and the sample left at least overnight, during which time it recovered its original pore volume. An external pressure of 12,000 psig was then applied and held constant. The change in pore volume was noted as the internal pressure was raised in 1,000 psig increments to 10,000 psig. The internal pressure was then reduced to zero, again noting pore volume changes,

By George A. Connell

BORAX, a sodium borate and the principal sodium salt of boric acid, has been surrounded with romance and with a certain amount of mystery. Its early history is not entirely known but it has been contended that Marco Polo in his travels in the Orient introduced this material to the West during the Middle Ages. Without doubt its first source was from Central or Eastern Asia and perhaps from Tibet. The well-known fluxing properties of borax probably introduced its earliest use that of a soldering flux in the manufacture of jewelry. This use, as well as the remote location of most borate deposits, added greatly to the romance associated with the thought of borax. COMPOSITION The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture. The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture. The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture of disodium tetraborate (Na2B4O7.10H2O), and, further, can be considered as the acid salt of monosodium metaborate. However, the term "acid salt" might imply that borax gives an acid reaction in solution, which is not true, since solutions of borax are decidedly alkaline, giving a pH of 9.2. Boric acid, also known as boracic acid, has the chemical formula H3BO3; it occurs in nature as the mineral sassolite. Sassolite has been

Jan 1, 1949

By James A. Barr

PUMICE and pumice are varieties of volcanic ejecta formed from lavas of the more silicic types. Chemical analyses of pumice, pumicite and perlite, from which synthetic pumice is now produced, will generally fall within the limits 65 to 75 pct silica, 9 to 20 pct alumina, less than 8 pct combined alkalies (sodium and potassium oxides), less than 3 pct calcium and magnesium oxide, less than 3 pct iron oxide, with smaller amounts of manganese, titanium, phosphorus and other oxides. Perlite is characterized chemically by having, in addition to the percentages of oxides given above, as high as 6 pct combined water. PROPERTIES Pumice is a natural silicic foam glass produced by volcanic eruptions. The molten glass foam, upon rapid cooling, trapped the steam and volcanic gases that caused it to remain extremely porous and vesicular in structure. Pumice is found in the form of large lumps several cubic feet in volume and also in grains only a few millimeters in diameter. Chemically, pumicite is of the same range of composition as pumice. The distinction between pumice and pumicite is one of particle size; the coarser materials are pumice; the fine particles, an appreciable percentage of which is in the range of 100 to 325-mesh or finer, are pumicite. If the erupting volcano ejects a silicic lava containing much gas and water vapor, the sudden release of pressure tends to free the gas. The viscosity of the lava, its rate of cooling and the amount of gas evolved, all have part in determining the degree of expansion of the glassy particles and the fineness of the vesicle. If the lava is of the correct viscosity and there is not too much gas, a pumice may be formed. Large amounts of gas may cause complete disruption into pumicite.30 In 1916, Barbour gave the name "pumicite" to the volcanic ash of Nebraska and since then the name has been widely used in industrial circles for the finer-grained commercial varieties. The glass of pumice and pumicite is transparent and colorless. It

Jan 1, 1949

By G. Thodos, R. J. Smialek

A method has been developed that permits the correlations of Mehra and Thodos8 and Dastur and thodos2 for binary systems to be used for the prediction of the vapor-liquid equilibrium constants of the light and heavy constituents, Kland Kh, of a ternary hydrocarbon mixture. Furthermore, the unique relationship observed in this study, i.e., a plot of log Ke/Ki vs log Kp/K h is linear and passes through the origin, permits the calculation of the K-value for the intermediate component. This approach has been used to establish K-values for the constituents of the three ternary hydrocarbon systems used to develop this method and has also been applied to two additional ternary hydrocarbon systems to yield an average deviation of 7.7 per cent resulting from a total of 294 points for the five ternary systems considered. INTRODUCTION The rigorous calculation of vapor-liquid equilibrium constants for systems containing two or more components is a difficult problem and becomes extremely complex at elevated pressures and for conditions approaching the critical point. Although thermodynamic relationships can be developed to account for the vapor-liquid equilibrium behavior of simple systems, their use is limited because the necessary PVT data for these systems are not generally available. To establish a method for calculating K constants directly, without any recourse to the PVT behavior of a system, Mehra and Thodos8 applied the principle of corresponding states to the vapor-liquid equilibrium constants of binary hydrocarbon systems. They developed a series of charts which made possible the prediction of K-values for all binary hydrocarbon systems not containing methane. This work has been extended by Dastur and Thodos2 to include binary hydrocarbon systems containing methane. The charts developed in these two studies cover the high-pressure region and are applicable to conditions in the vicinity of the critical point. The ability of this approach to predict vapor-liquid equilibrium constants of binary hydrocarbon systems suggests that this method may be extended to the prediction of the K-values of the components of ternary hydrocarbon systems. In this investigation, the charts developed for both the methane and non - methane binary systems,2,8 together with mixture rules developed in this study, have been used to predict the K-values of the light and heavy components of a ternary hydrocarbon system. These calculated values are then used to establish the K-value of the intermediate component through the use of a novel relationship developed in the present study. DEVELOPMENT OF METHOD FOR PREDICTING K-VALUES OF TERNARY SYSTEMS The application of the corresponding state charts developed for binary hydrocarbon systems is restricted to those systems containing two components. The extension of these correlations to three-component systems requires that the ternary system be reduced to an equivalent binary, which can be treated in a manner consistent with the corresponding state development. To establish such an approach, the vapor-liquid equilibrium constant of the light component K is first calculated by assuming that the ternary mixture consists of the light component and a pseudo-heavy component of the intermediate and heavy constituents of the original ternary. To establish the vapor-liquid equilibrium constant of the heavy component Kh, the light and intermediate constituents of the ternary are combined to form a pseudo-light component of another equivalent binary system. The calculated values Kl and Kb are then utilized to calculate the vapor-liquid equilibrium constant of the intermediate component EQUILIBRIUM CONSTANT FOR LIGHT COMPONENT K To calculate the K value of the light (most

Jan 1, 1965

By Richard L. Seal, Allan L. Turner

INTRODUCTION The chapter discusses the procedures and operations starting with the actual training of operations personnel with respect to a grinding mill circuit and a typical check-out and start-up of a grinding circuit before turning over the operating circuit to production personnel. For the purposes of this paper, it will be assumed that the mill circuit installation is at a new location or a new operation at an existing operation. Expansion of an existing grinding facility would probably require less time-consuming and less costly procedures than those that will be outlined here. There are numerous arrangements and types of equipment that can be used for grinding circuits. For example, the grinding could be wet or dry. The grinding mill could be a rod or ball mill or some combination. The circuit could be open or closed. The closed circuit classification could be accomplished with rake classifiers, spiral classifiers, cyclones, stationary screens, or vibrating screens. To limit the discussion, the grinding circuit shown on Figure I will be discussed. The circuit includes a dry ore feed by a belt conveyor (feeder) to a wet ball mill. The ball mill discharges to a cyclone feed pump box and pump. The pump feeds a cyclone type classifier with the cyclone underflow returning to the ball mill feed and cyclone overflow being the required grinding circuit product. For the purposes of this paper, it will also be assumed that the extensive overall preparation necessary for every start-up has been accomplished. These preparations are only outlined here as they have been adequately dealt with in recent papers. (1), (2), (3) The items in these preparations would include. 1. Appointment and indoctrination of the start-up organization. 2. Integration of the start-up into the overall project schedule. 3. Development of the specific start-up schedule. 4. Budget determination and monies appropriation.

Jan 1, 1982

By W. M. Peirce, E. A. Anderson

A FEW metals have been known since the dawn of history. Many have been prepared in quantity only within the present century. Zinc falls into an intermediate category, although there is some evidence of its existence in elemental form in Greece as early as the third or fourth century B.C. Nevertheless, the first important use of zinc antedates the earliest records of civilization. This first use was in the alloy, brass, which is roughly one third zinc. This continues to the present time as one of the major uses of the metal. The first production of brass, in light of present knowledge, was perhaps one of the 'most romantic and fortuitous of technical discoveries. Copper, the major constituent of brass, had been given to man by Nature in the native state; that is, as lumps of fairly pure copper. The art of melting and working it had been learned. But zinc does not occur as the metal in Nature and even if some early metallurgist happened to heat zinc ore with a reducing agent, the reduced metallic zinc passed off as vapor and was lost. Doubtless some early coppersmith, melting copper in accidental contact with zinc ore, reduced the zinc, and the vapor was absorbed by the molten copper. Its color, hardness, and other properties were thus wonder- fully changed. And so the earliest metallic form of zinc, as nearly as we can deduce, existed in the alloy brass. Probably knowledge of the kind of rock with which to heat copper to change it to brass, the best

Jan 1, 1953

By Wallace W. Key

Chalk is a natural calcium carbonate occurring as the remains of soft, friable, minute marine organisms. Whiting can be either finely ground calcium carbonate prepared from chalk, marble, or limestone or the product obtained by chemical precipitation from a solution or suspension containing lime. Until relatively recently, whiting made from limestone was termed "whiting substitute," but it is now usually designated as limestone whiting. Precipitated calcium carbonate, sometimes called "precipitated whiting" or "precipitated chalk," is a finely divided calcium carbonate product obtained by chemical precipitation from a solution or suspension containing lime. Considerable quantities of precipitated calcium carbonates are produced from many chemical processes. Naturally occurring calcium carbonate in a variety of crystalline forms and in all degrees of chemical purity forms a substantial part of the earth's crust. Exactly where a chalk grades into a marl or calcareous shale through increase of clay or silt or into a hard limestone through consolidation and crystallization is difficult to determine because no rigid specifications have been promulgated for classifying them. Composition and Properties Once considered to be amorphous, chalk was later found to be cryptocrystalline. In the pure state it consists entirely of CaCO3, but many deposits are impure. When impurities are removed and the material is reduced to a finely divided state, it is known as chalk whiting. Much confusion attends the use of the term "chalk" as well as the classification of whiting materials. For instance, blackboard chalk is not necessarily chalk but is sometimes plaster of paris or a form of talc. Colored "chalks" may be true chalk colored and compressed with a binder but are probably such materials as hematite, clays, or carbonaceous matter. The term whiting was applied exclusively to the product derived from true chalk before World War I. Chalk imports were difficult to acquire during World War I, and whiting substitutes, a term applied to the products derived from natural rock deposits and precipitated calcium carbonate, were introduced. Substitute whitings were not acceptable at first, but it was found that blending true chalk with substitutes often created an improved product; eventually by selection of limestone and finer grinding, products not only acceptable, but for some uses superior to chalk whiting, were developed. Gradually the term "substitute" was dropped because chalk whiting had lost its importance, being largely supplanted in the United States by other whiting materials. Whiting is now made in ever-increasing quantities from limestone, marble, dolomite, marls, vein calcite, oyster-shell, as well as primary and byproduct precipitated calcium carbonates. Distribution of Chalk Europe-In England, France, Belgium, Denmark, and other European countries highpurity chalk occurs in extensive beds. The Cretaceous period, or the "age of chalk," in geologic history receives its name from the great deposits of chalk exposed on either side of the English Channel. It has been estimated that oceans in which chalk and allied deposits were formed covered more than 500,000 square

Jan 1, 1960

By J. Suiter, H. F. Ryan

H. F. Ryan and J. Suiter (CSIRO)—In this paper the authors have presented "a physical model which has as its central hypothesis the solution strengthening of regions along grain boundaries in the order of tens of angstroms thick", and their calculations have used 40Å as the zhalf-width of this boundary region. Selection of this value by the authors suggests that they were unaware of a number of recent field-ion microscope observations of grain boundary structures (e.g., Refs. 29 and 30). The accompanying figure, Fig. 9, shows a portion of an ion micrograph of a tungsten specimen containing a grain boundary, and the regular arrangement of atoms in various crystal planes in each grain can be seen, except in the boundary zone which is not more than two atom diameters in width. Since it is expected that solute atoms will segregate only to the region where the lattice is disturbed, it would seem that a value of 4Å for the half-width of the boundary region would be more appropriate than the value of 40Å assumed by the authors. If the former value is used in Eq. [8] of their paper to obtain curves showing solute concentration in the grain boundary as a function of temperature, the resulting curves differ significantly from those obtained by the authors. Although there are only relatively slight changes in the regions corresponding to higher temperatures (i.e., grain boundary concentrations of approximately 1 at. pet), at lower temperatures the curves are no longer realistic. For example, the curve corresponding to u = 7000 cal per mole gives a solute grain boundary concentration in excess of 100 pet at a temperature of approximately 360°K, and "flattens out" at a grain boundary concentration of about 300 pet! Similar results are obtained with each of the other curves. Ion microscopy of dilute solid-solution alloys has shown that solute atoms give rise to image points which in most cases are of higher intensity than those of the solvent atoms.31 If the same behavior occurs when the solute atoms are present in much lower concentrations then ion microscopy should provide a sensitive tool for studying the segregation of impurities to the grain boundary regions. Although many grain boundaries in tungsten have been examined after different thermal and mechanical treatments, there has not been, as yet, any systematic study of such segregation. In general the micrographs show no clear indications of marked grain boundary segregation, but occasionally areas are found where the grain boundary contains an appreciable number of image points of high intensity in a very narrow zone, see Fig. 9. If it is assumed that these correspond to impurity atoms then it is possible to estimate the impurity concentration both in the grain boundary and within the body of the grains. Application of this method (to a larger area

Jan 1, 1965

By Thomas M. Drown

In the course of some experiments on the analysis of pig iron, I heated, in a platinum crucible, some borings of a graphitic pig iron with sodium carbonate. When the crucible was at a full red heat and the carbonate was thoroughly fused, I noticed a lively ebullition of the mass, and an escape of gas, which burned on the surface. On investigation this gas proved to be carbonic oxide, and on examining the borings in the bottom of the crucible after an hour or two, they were found to be perfectly malleable, although unchanged in general form and appearance. Analysis showed that the carbon was completely removed. I then repeated the experiment, to ascertain whether the silicon and phosphorus were affected, and found that these elements too were largely removed, and could be .found in the fused mass as alkaline silicates and phosphates. In order to ascertain whether the removal of the silicon and phosphorus was merely a surface action or whether the reaction really extended into the mass of the iron, I tried the following experiments : A number of bars of pig iron were cast about one foot long and planed down 'accurately to one inch section. These were immersed in a large wrought-iron pot full of molteu sodium carbonate made by fusiug the commercial bicarbonate of soda. Through the kindness of Mr. Frank Firmstone, Superintendent of the Glendon Iron Works, Easton, I was enabled to keep this pot at a reasonably constant high temperature for a long time in one of the hot-blast ovens. One of the bars was removed from the pot every twenty-four or forty-eight hours, according to the rapidity of the action, and after cooling mas broken and the fracture examined. The change from pig iron to malleable iron was progressively inwards and always sharp and easily recognized, the rate of progression being in a decreasing ratio with the time. The temperature of the oven had evidently

Jan 1, 1879

By Homer W. Riley, C S. Jenkins

SMALL power-driven, toothed, cast-iron rolls were used first to break anthracite in 1844. Prior to that time, men with hammers, who stood on perforated cast-iron- plates, .broke the large lumps into commercial sizes. In order to convert run-of-mine into the various sizes required by the anthracite industry, about 20 million tons must be broken, annually, [ ] into smaller sizes. This phase of anthracite preparation is of major importance, because the degradation accompanying reduction in coal sizes should be kept at a minimum. The exclusive use of toothed rolls for that purpose indicates that comminution by rolls is the best solution of the problem. Many improvements have been made in tool design, but the most important was a reduction of the peripheral speed of the rolls from 1000 to 300 ft. per minute. The higher speed was based upon and approximated the velocity of a falling piece of coal when it entered the rolls. Exhaustive roll tests at the slower speed showed that the same size reduction could be affected with less degradation. The adoption, there- fore, of slow-speed, compound geared rolls, especially for breaking the

Jan 1, 1943

For convenience, we tabulate below the weight systems contained in the Probierbüchlein: [Pound and centner weights used by merchants for ore, lead, and copper I frother = 20 or 50 centners (depending on locality) I centner (Stolberg & Eisleben) = 112 pounds. I centner (Nuremberg) =100 pounds I pound =2 marks =32 lot =128 quintlein-512 pennyweights =1024 beller I mark -16 lot -.64 quintlein =256 pennyweights = 512 beller 1 lot= 4 quintlein= 16 pennyweights= 32 beller I quintlein = 4 pennyweights= 8 beller I pennyweight = 2 beller Netherlands mintmasters' weights for silver I mark =12 pennyweights=288 grains I pennyweight - 24 grains Assay weights for gold I mark= 24 carats 96 carat-grains. I carat = 4 carat-grains] The assayer's weights were miniature copies of the legal weights of his locality, intended, like the modern assay ton, to eliminate calculation. Each assayer made his own, not usually bothering about a given proportion between the true weights and the assay set, but maintaining the correct ratio between all the weights in any one set. The weights were quite small, to permit the use of less sample, but the exact size is nowhere stated in the Probierbüchlein. Even the legal pound varied considerably from place to place, depending on locality, and assayers would use different factors depending on the sensitivity of their balances, among other things. Agricola makes the assay centner equal to one actual drachma, by which term he means the German quintlein, or 1/12,800 of the full weight of the 100-pound centner. Schreittmann says that the 100-pound centner on the assay scale should be less than half a quintlein, i.e., the factor should be at least 25,600. Biringuccio says the assay centner might

Jan 1, 1949

By Mohamed Mortada

A practical analytical method is developed in this paper which provides the practicing reservoir engineer with a handy method for analyzing oilfield interference problems. The procedure employed entails the principle of superposition of individual eflects. A set of charts has been developed and can be used to evaluate the individual effects. The charts represent non-steady state pressure distribution in an extensive aquifer due to a constant rate of production from an oilfield which can be approximated by circular geometry; they are constructed from solutions to the diffusivity equation considering a circular sink as distinguished from a point sink. The solutions are obtained partially from mathenlatical considerations and partially from analog and digital computations. By virtue of the method of images, the charts can be used also to treat the case of production near a fault. In addition, provisions are made for treating oil fields, which are produced by partial water-drive. Treating an actual field case is deferred to a subyequent writing; however, illustrative example is presented to demonstrate the method of application. The pressure distribution in linear and limited radial aquifers is currently under study. INTRODUCTION With the increasing difficulty of discovering new oil reserves, attention is necessarily focused on the efficient development and production of existing reservoirs. Efficient production depends on the availability of reliable means for predicting the pressure-production behavior of oil fields. The prediction is usually performed by analytical methods or computers. Analytical methods are often limited to systems which can be approximated by simple geometry. However, analytical methods have the distinct advantage of being readily performed without special equipment. Analog and digital computers lend themselves to a variety of problems, but are not always locally available and consequently their use is limited. One particular situation in which analytical techniques are needed involves studies of multiple, water-drive oil fields sharing a common aquifer. Such oil fields are in hydrodynamic communication. Therefore, production from any of the oil fields is accompanied by a pressure decline which is transmitted through the aquifer to the other oil fields and manifested as pressure interference. The rate of propagation of the pressure decline is such that the pressure may be significantly reduced many miles away from a producing pool. An example of pressure interference is found in the Woodbine formation in East Texas. There. a dozen or more pools, including several of major size, draw on the Woodbine formation for water drive. The pressure in the water-bearing portion of the formation has been significantly reduced over an area of several thousand square miles. This reduction of pressure has been such that when the Hawkins pool was discovered in 1940, the pressure in it had already been reduced 280 psi below the initial value in the aquifer. This resulted from prior production from other Woodbine sand pools, including, in particular, the East Texas field some 20 miles to the east of Hawkins.' The above example indicates that the interference effect can be significant and should be taken into con-

Jan 1, 1956

EdgaR S. Cook, Pottstown, Pa.:—Many friends and acquaintances seem to be under the impression that the Warwick Iron & Steel Co. received a' license from Mr. Gayley, free of cost, as an inducement to adopt the process. This impression is not correct, since the license was paid for, and I think it was the first payment that Mr. Gayley received for the use of his process. As president of the Warwick Iron & Steel Co., I am responsible for its earnings, and with only the experience at the Isabella furnaces as a guide, the directors of the company considered that there was a great risk in expending the large sum of money required for the plant. They, however, acted favorably upon my recommendation, and to this extent I am responsible for the installation at the Warwick furnaces. I made the best agreement possible with Mr. Gayley, and naturally our company received certain advantages. It will be contrary to all experience if subsequent plants do not show some improvements and economies in construction. It is to our indirect benefit that all subsequent licenses granted by Mr. Gayley should be charged at a much higher rate than we paid; and I trust that he will see to it that all such licenses granted, especially to companies making merchant iron, shall be at a maximum figure. The Warwick Iron & Steel Go. is not interested in any way in exploiting the merits of the Gayley dry-blast process; on the contrary, looking at the subject from a narrow and selfish standpoint, it is to the advantage of our company that no merchant blast-furnace competing with our iron-product should be equipped with a dry-blast plant. There is a clause in the contract with Mr. Gayley, whereby our company agrees to furnish him with all the data derived from the operation of the dry-blast plant, and that he or his

Jan 1, 1909

By R. E. Gilchrist, R. R. Harvey, M. R. Dean

A simple and rapid three-component analysis procedure has been developed for use in fluid-flow studies. The method is based on refractive index measurements, combined with refractive dispersion measured between the Ha and H wave lengths. The procedure requires. calibration curves for the three-fluid system. The only restriction on the fluids employed is that only one be an aromatzc or olefinic compound. Individual sample measurements require only a few minutes. Composition results within the limits of accuracy required for fluid-flow analog studies are obtained. INTRODUCTION The simultaneous analysis of three-component mixtures is a problem often encountered in fluid-flow analog systems. In petroleum production research, the problem is usually encountered in experiments on the displacement of fluid from a porous medium. In the case of immiscible displacement, simple volumetric measurements of the produced fluids are usually sufficient, the analog fluids often being the actual reservoir fluids themselves — oil, water and gas. However, modern secondary recovery of petroleum sometimes involves production under miscible conditions, in which the oil is displaced by liquefied petroleum gas which, in turn, is displaced by dry gas. Since this type of displacement is done under conditions of pressure and temperature that are not easily reproduced in the laboratory, studies are often performed with analog fluids at essentially atmospheric pressure. Since the number of samples taken during one of these experiments is usually quite large, the time required for analysis becomes an important factor. In the past, the difficulty of conventional analysis has been avoided by the addition of various tracers to one or more of the components, or by the use of a tracer fluid as one of the components. With these techniques, a relatively large amount of analytical time is still required. Moreover, in the case of added tracers, the tracer material may migrate in part to one of the other fluids, may be adsorbed on the solid surfaces of the model, or may introduce side effects not characteristic of the prototype fluid. The substitution of a tracer fluid for one of the components can severely limit the choice of analog fluids. Optical refractometry provides a rapid and economical method of analysis of two-fluid systems or of monitoring small changes in composition of an essentially one-component system. Refractometric methods are capable of high degrees of accuracy, require only very small samples and can easily be adapted to automatic methods. They are not generally applicable, however, where three or more fluids are present over wide ranges of concentration. The method of three-component analysis described here has three essential characteristics. 1. It is based on refractometric measurements and thus preserves all of these desirable properties. 2. It does not make any stringent demands on the choice of fluids that can be analyzed. 3. It is capable of accuracy sufficient for fluid-flow analog studies. THEORETICAL The difference in the refractive index of a substance at two different wave lengths of light is known as its dispersivity. When the difference is taken between the specific refractions at the two wave lengths, the quantity is referred to as the specific dispersivity. Specific refraction was defined empirically by Gladstone and Dale1 as r = n-1/d....[1] where n is the index of refraction and d is the density. The definition is given more correctly by the expression r =n2-1/n2+1 1/d..........(2) 1References given at end of paper. MICIFTV OF PETROLEUM ENGINEER JOURNAL.

By R. V. Lundquist

Leaching manganese-bearing materials with NaOH to remove caustic-soluble silica has been demonstrated as a method for upgrading manganese. Those materials containing opaline varieties of silica respond most readily. Spent leach liquors are regenerated by treatment with lime to precipitate calcium silicate and to reactivate the NaOH for leaching. ALL of our larger domestic deposits of manganese are very low grade, but estimated tonnages in these deposits are large enough to constitute a potential strategic reserve of manganese for emergency periods, provided these ores can be upgraded sufficiently to meet industrial specifications. Many types of processes have been suggested for upgrading these ores, several have been studied in pilot plants, and a few have attained limited commercial production for special purposes. The hydrometallurgical process to be described below proposes a leaching operation for removing caustic-soluble silica and other gangue minerals and consequently upgrading a manganese ore or flotation concentrate to a commercially acceptable moduct. It is known that some forms of silica and some silicate minerals are soluble in NaOH solutions under suitable conditions. This new process proposes to use NaOH for removing the soluble materials from manganese ores or concentrates and, as a result, upgrade the manganese content. Since spent leach liquors are not efficient leaching agents the liquor must be treated with lime to precipitate calcium silicate and reactivate the NaOH. Experimental Procedure Manganese-ore samples ground to —35 mesh were leached in iron containers into which the ore sample and appropriate NaOH solutions were placed. Flotation concentrates were already ground to —200 mesh. The slurries were then placed on a hot plate or into a pressure digester and stirred continuously during the period of digestion. Where the- digestion was performed at atmospheric pressures, water lost by evaporation was replaced at regular intervals to maintain approximately a constant volume of slurry. In the pressure digester, volume changes were not controlled. After digestion, the slurry was allowed to cool enough for easy handling, but it was filtered hot, 50" to 70°C, on a Buechner filter. Filtration under these conditions was satisfactory. The resulting filter cake was washed and dried. In most instances, a single leach would not produce maximum extraction of silica from the ore sample; consequently, the dried tailing was treated again in the same manner with a fresh solution of NaOH to obtain an additional extraction of silica. This procedure was repeated a number of times to get the maximum extraction of silica. Usually three or at most four stages of leaching were adequate for this purpose. This leaching procedure was used for obtaining the data reported in this paper on the effects of NaOH concentration, pulp dilution, temperature, and time of digestion on the efficiency of extraction of silica from the ore sample. The experimental procedure does not match industrial methods. consequently tests for counter-current leaching were set up. Data from these tests are not yet complete, but in a qualitative way they indicate that thickeners between stages of leaching will be satisfactory and that the quantity of silica in a leach liquor moving forward to a new solid has only a minor effect on the quantity of silica extracted from the new solid. A pilot plant is now being designed for operation in the near future to test and evaluate the merits of this process.

Jan 1, 1954

At a large meeting of the members of the American Fund for French Wounded it which Mr. Franklin D. Roosevelt presided and at which Mrs. B. Girault Lathrop, President of the Paris Administration A. F.F. W., gave a most interesting address, special rows of seats were reserved for the members of the W. A. A. I. M. E. Those who were unable to be present will be glad to hear that Mrs. Lathrop complimented our organization on having supplied the largest dispensary operated by the A. F. F. W. and the Red Cross in northern France. The A. F. F. W. is going to erect an American Memorial Hospital at Rheims and it is hoped that the one hundred beds in the hospital will be endowed in memory of the men who gave their lives for the liberty of the world. It will be possible not only to endow beds, for which sums of $6000 each are needed, but also to give, as. memorials, sun- parlors at a cost of $10,000 each, two roof gardens at $5000 each, a laundry at $10,000 and a garage at $10,000. The New York Section has undertaken to endow a heel in memory of members of the A. I. M. E. who gave their lives in the Great War. Perhaps other Sections or groups of Sections may wish to do the same thing, or if no other Section cares to assume so much responsibility possibly individuals may like to join the fund already growing in New York, in which case they should send their contributions to Mrs. W. Y. Westervelt, 1 Lexington Ave., New York, N. Y.

Jan 6, 1919

By Augustus Locke, Edward H. Perry

In the exploration of a copper deposit by drilling, obvious advantages are to be gained from a distinction between primary and secondary ore.' Perhaps the chief of these is the aid which such a distinction renders in determining where a given hole should stop. The copper assay, often a sufficient guide, cannot always be exclusively relied upon. Primary ores may extend downward indefinitely and may fluctuate in value independently of depth: if primary ores are consistently lean for a considerable vertical distance, there is little reason to expect that, still deeper, they will increase to the commercial grade; on the other hand, rich primary ores may persist uninterruptedly downward or may come in again below a lean interval. Secondary ores, however, have a comparatively limited vertical extent; in a large way enrichment decreases with depth and finally gives out. It follows then, that when a hole descends from profitable ore into ore of less than the commercial minimum, the practical significance of the situation depends upon whether this decrease results from a decrease in secondary enrichment or is a variation in primary content: if the copper of the ore passed through has been chiefly secondary, little is gained in the average case by extending the hole much below the point at which the commercial limit is reached; but, when copper is chiefly primary, due weight must be given to the possibility that, still deeper, the ore may again improve. The distinction between primary and secondary ore may of course be effected through an examination of the drillings. It has been found, however, to be facilitated by curves made by plotting assays against

Jan 1, 1916

By J. Chipman, N. J. Grant, H. L. Bishop, H. N. Lander

Data of several studies on the equilibrium between molten iron and open hearth-type slags have been combined to determine some of the chemical reactions involved in steel-making. Effects of slag composition and temperature on the iron oxide activity, distribution of sulfur between slag and metal, and the carbon content of the metal are discussed. Also, an overall reaction for the equilibrium between sulfur and oxygen is presented. DURING the past 15 years, a number of significant equilibrium studies have been carried out between liquid iron and simple basic and acid slags in an effort to throw light on the chemical reactions involved in steelmaking. This paper is a summary of the experimental reports on investigations which have been conducted at the Massachusetts Institute of Technology, and of related work in other laboratories. The investigations summarized in this paper include the works of Fetters and Chipman1 and Taylor and Chipman,' which dealt with simple slags that are similar to those found in the open hearth. The sulfur determinations of the slag-metal tests of Fetters and Chipman as reported by Grant and Chip-man" are included. Also, the investigations by Win-kler and Chipman' and Grant and ChipmanQ f more complex slag systems are included in this summary. The experimental procedure is described in detail in each of these papers and will not be discussed. Since the previous reports have been somewhat independent, it is desirable to review and combine the data of the various investigations to determine, as accurately as possible, the reactions in the slag-metal systems of the open hearth. It is the object of this report to present the combined data in such a way as to enhance their utility and applicability. Oxidizing Power of Slags of the System (CaO+MgO)-Si0,-FeO in Equilibrium with Carbon-Free lron The slags selected to determine the iron oxide activity in equilibrium with pure liquid iron were those containing less than 2 pct each of P,O,, MnO, or A1,0, on a weight percentage basis. The method used to calculate activities of iron oxide in liquid slags was that developed by Taylor and Chipman.' The solubility of oxygen in molten carbon-free iron under pure iron oxide slags can be expressed by the following eauation —6320 log (pctO)-------------— + 2.734 [1] where T is the absolute temperature. The oxygen solubility values as determined from Eq. 1 were used throughout this study to calculate the iron oxide activity. The iron oxide activities of slags of various iron oxide contents are plotted in Fig. 1 as a function of the basicity, which is defined as the ratio (pct CaO + pct MgO)/pct SiO,, and are based on molecular percentage values of the components. The percent (FeO), is the total iron content in the slag calculated to FeO. Fig. 1 shows that as the basicity increases at constant mol pct (FeO),, the iron oxide activity increases rapidly and reaches a plateau which extends on the basicity scale from about 1.3 to 2.3; the iron oxide activity then decreases rapidly until a basicity of about 3.0 is reached, where it tends to level off. The solid portions of the curves represent the experimental data of Fetters and Chipman and Win-kler and Chipman. Their experimental heats were made in magnesia crucibles, and hence the slags were saturated with magnesia. The broken lines on the left represent the experimental data of Taylor and Chipman, who used a rotating crucible. In general, these slags contained less than 3 pct MgO. The absence of data for slags containing less than about 40 mol pct (FeO), and basicity ratios greater than about 2.5 made it necessary to calculate curves using ionic concepts of slags. The broken lines on the right, which disregard the solubility limits of di and tricalcium silicate and lime, were obtained by following the treatment of Flood and Grjotheim,"

Jan 1, 1957