Search Documents

By Enrique Touceda

As in the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time.. A few years ago, about the only test made to ascertain the physical properties of the product, except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 1, 1922

IN the western mines, the boss, engineer, geologist, or nipper in making rounds have a password which usually guarantees safe entrance to a working place from below the working miner. Most men won't climb a raise or enter a stope from below where a miner is working until they have shouted "nothin' down" and heard those words shouted back by the miners above. "Nothin' down" is a safety pledge as necessary and as binding as the truce flag to the soldier. It implies mutual confidence that work will be suspended until the person below has come abreast of the workers; and also confidence that the miner who replies "nothin' down" is reasonably sure the place is safe to enter. Like truce flags which are not infallible, so is this password subject to human errors or unexpected falls of rock, tools, or timber. Everyone knows these unavoidable hazards, but what is important to the exposed man is that in that precise moment of time when he has heard the reassurance of "nothin' down," he knows that safety is uppermost in the minds of the men above him. With such assurance we would go anywhere and so would most mining men. If that period of safety consciousness, procured by the utterance of two words, could be multiplied to equal the hours in the working day, there would not be any accidents but those by "the act of God." It is the aim of every safety program to make safety as natural as breathing. That is the reason for the posters, the conferences, instruction periods, safety engineers, and the inspections. But none of these are as effective as one accident, which keeps men on their toes for weeks to come. This is not the price we want to pay for safety consciousness. This Annual Review number of Mining Engineering is full of talk about production. Production for defense, production for profit. In this tremendous surge of industrial might . to make this nation and our very families safe S from the predatory forces abroad in the world today; let us not lose sight of the fact that the . safety of our manpower is more precious than any commodity. Production without safety is detrimental to the national interest, to that of the company, and to the individual. If the words "nothin' down" can give us the best human guarantee of safety, for however brief a time, let us adopt them at least in principle as our slogan in 1952. Production for preservation in '52 - but NOTHIN' DOWN!

Jan 1, 1952

By R. Raring, W. J. Harris, J. A. Rinebolt

The effects of additions of alloying elements on the true-stress, true-strain characteristics of 0.30 pct C, 1.00 pct Mn, 0.30 pct Si pearlitic steel were studied. The alloying elements investigated were C, Mn, Si, P, The alloys are compared on the basis of fracture stress, fracture strain, energy to fracture, rate of strain hardening, strain hardening exponent, height of the flow curve, and lower yield point. IN the past, nearly all studies of the effects of alloying elements on the tensile properties of metals have compared the conventional engineering parameters, namely, tensile strength, yield strength, elongation, and reduction of area. Recently, however, the true-stress, true-strain method of recording results from the tension test has been used; Lacy and Gensamer,' Hollomon," and French and Hibbard- are used this method to study the effects of composition on strength and ductility of metals. In this paper, the effects of certain alloying elements on true-stress, true-strain curves of steels with nearly constant grain size and pearlite spacing are presented. The notation employed in this paper is given in Table I. Since the definitions of stress and strain and the analytical geometry of the stress-strain curve have been explained previously, for example by Gensamer,' they will not be reviewed here. However, the method used for the determination of energy to fracture, E,, requires mention. These energy values were calculated on the assumption that the flow curve followed the idealized equation:' corresponds to the specific energy absorption to that strain value. There is justification for preferring the use of eq 1 for the determination of the energy to a particular strain rather than the area under the experimental stress-strain curve, since Gensamer showed that the use of the Bridgman correctione for stress at the neck of a tensile specimen brought the corrected experimental curve nearer to the idealized power-law curve than to the uncorrected experimental curve. However, it should be noted that the difference between the areas under the idealized curve and the experimental curve is not great for strain of less than 1.0, as can be seen from Fig. 1. In this figure, the true-stress, true-strain curve for a 0.01 pct C, 1.00 pct Mn steel is plotted through the experimental data points. From the value of a,, from this curve and the value of n as determined by the Inm-

Jan 1, 1952

By Luis Elek

DEVELOPMENT of the cement industry in Mexico began some 40 years ago. It has gradually reached great importance in the economic life of the country and has contributed greatly to the technical and economical advances which have been so noteworthy, particularly during the last 15 years. From a modest start, the industry now comprises 18 cement-producing plants having a potential annual capacity of approximately 14 million bbl. About half the plants were built and equipped with second-hand machinery during the last world war when no new machinery could be procured. They will hardly attain full production before being modernized and reconditioned, a job now under way in several of the plants. At present, the yearly consumption is only about 8 to 9 million bbl but is steadily increasing. This is only a fraction of the cement consumed in the U.S.A., which is about 250 million bbl per year, although on the basis of consumption per capita per year, the figure is 1/3 bbl for Mexico and 1 2/3 bbl for the U.S.A. Cement consumption in Mexico is well above the average of all other Latin American countries, with the exception of the Argentine, and considering the potentialities and undeveloped riches of Mexico, the road construction and irrigation works, it is fair to assume that the Mexican cement industry will still prosper and expand in spite of temporary setbacks in the future caused by-local events of economic or political nature. Portland cement is manufactured by burning a mixture of raw materials, one of which is mainly composed of calcium carbonates and the other of aluminum silicates. The most typical materials answering this description are limestone and clay, both of which occur in Mexico in many varieties. To be usable for cement manufacture limestone should contain at least 77 to 80 pct calcium carbonate. Lower grade limestone can be used for cement manufacture only if the lime content is increased by the beneficiation process, which has not yet been adopted by the Mexican cement industry. Most of the limestone used by Mexican cement plants has a calcium carbonate content of 90 to 95 pct and therefore requires addition of one or several correction materials. A typical composition of raw mix for cement manufacture is 85 pct limestone and 15 pct shale, clay or volcanic materials. Occasionally it is necessary to add a smaller amount of sand or other siliceous material to increase the silica ratio in the raw mix. Likewise, it is sometimes necessary to add 1 or 2 pct iron ore to facilitate fusion in the kiln and to obtain proper relation between alumina and iron oxide. After calcining and

Jan 1, 1952

By J. W. Rutter, K. T. Aust

In previous studies of grain boundary migration in zone-refined lead, the authors used bicrystal specimens consisting of a striated crystal which was grown from the melt, and an adjacent striation-free crystal, introduced by artificial nucleation and growth.1 While this method permits the study of the motion of individual grain boundaries, it does not provide control of the relative orientations of the grains. The present note will describe a technique for controlling the orientations of the two crystals in this type of specimen. The technique consists essentially of placing a striated crystal and a striation-free crystal of controlled orientations end-to-end in a graphite trough, then melting a short zone at the junction of the two crystals and allowing it to freeze to form the desired grain boundary. The apparatus used to carry out this process is illustrated in Fig. 1. It consists of a trough milled from high-purity graphite,with grooves in the underside for the placement of thermocouples. The graphite piece fans out on one end at the level of the bottom of the trough; the sides of the trough are completed in this region by the attachment of a mating plate with a slot cut at any desired angle to permit reorientation of the crystal placed at this end of the assembly. The joint between the crystals is made at or near the point where the slotted plate joins the rest of the trough. The thermocouple slots are deepened in this region so that the thermocouples are separated from the melt by only 1/32 in. of graphite. An induction heater, with suitable temperature control, is used to obtain the molten zone. The two single crystals used are first chemically polished in a solution consisting of eight parts glacial acetic acid and two parts 30 pct hydrogen peroxide. They are then placed in the trough with the ends to be joined at the position of the thermocouples. Next, cooling is applied to the two crystals by means of air

Jan 1, 1962

By Y. C. Kim, S. L. Barua

Underground coal mine planning has traditionally focused on the mine design aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most US underground coal mines. With the enactment of the Clean Air Act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the Btu content of coal are equally important for boiler efficiency. Coal mine planning must incorporate coal quality control aspects as well as traditional safety and efficiency aspects. According to an article in Coal Age (March, 1982), nearly one-half of the US coal exported to Europe does not meet the contract specifications regarding ash, sulfur and Btu contents. Although one of the reasons cited for this problem was "inadequate sampling at the US ports," the more fundamental cause probably lies in the inadequate quality control of run-of-mine (ROM) coal at the source. To perform adequate quality control of ROM coal, mines need predicted short-term in-situ coal quality information. Such predictions are generally based on whatever available sampling information is around the mine workings. Unfortunately, the closest sampling information, in the form of diamond drill hole assays, is often several thousand feet away in most underground coal mines and is inadequate for short-term coal quality prediction purposes. This is because the diamond drill holes (DDH) were traditionally placed in the coal deposit during the mine development phase to determine coal seam continuity and overlying roof conditions. They were not placed for short- term mine planning. A study was undertaken by the University of Arizona for the Homer City Owners in Pennsylvania to show that there is a need for more closely spaced samples, if the short-term coal qualities are to be predicted with any "reasonable" degree of accuracy. Prior to this study, a short-term quality prediction model, STPM, had to be developed. This model uses not only DDH, but also other sample information obtainable during face development work to predict the qualities of in-situ coal that are available in the immediate future.

Jan 1, 1985

INTRODUCTION Porphyry copper deposits have been reported from the Caribbean area by Pease (1966), Cox, et al. (1973), Guild (1974), Kesler, et al. (1975), and others. This chapter summarizes the most widely known characteristics of those deposits. Only one deposit that conceivably can be classed as a porphyry copper occurrence is in production (Pueblo Viejo, Dominican Republic), but others are known whose tonnage and grade are of economic interest. Deposits in this province may be classified as copper-gold or copper-molybdenum types (Kesler, 1972), but deposits associated with quartz-rich plutons that have high Na2O:K2O and high gold:copper but low molybdenum: copper ratios dominate. Porphyry copper occurrences are reported in the literature from Puerto Rico, Haiti, the Dominican Republic, Jamaica, and Cuba. Only the porphyry copper deposits from Puerto Rico are extensively described in the literature; consequently the Caribbean porphyry copper province in general is not as well documented as the southern Cordilleran orogen. Because past published technical descriptions are incomplete, some data presented here are new to the literature. The Caribbean includes the island arcs between North and South America. Porphyry copper occurrences are known from the Greater Antilles, the generally east-west trending group of islands that lies south of North America. Fig. 48, therefore, only covers the Greater Antilles portion of the Caribbean. Porphyry copper deposits in this area are not described by the Lowell and Guilbert (1970) model in details of metallization (general paucity of molybdenum), alteration (scarcity of orthoclase), or petrography (preponderance of quartz diorite). Therefore, this model should be modified to include deposits associated with quartz-bearing plutons such as those found in the Caribbean. In the Meme deposit on Haiti ore occurs in skarn adjacent to the quartz diorite phase of a composite quartz monzonite-granodio-rite-quartz diorite pluton (Kesler, 1968). This deposit, with a K-Ar 66 m.y. date, is not included in Fig. 48 as a porphyry copper deposit because metallization is restricted largely to the intruded rocks. Although the intrusive rocks at the Meme deposit may contain sulfide near skarn contacts they are otherwise essentially unaltered. Porphyry molybdenum deposits as defined by Clarke (1972) have not been reported in the Caribbean area.

Jan 1, 1978

R. V. Norris, Wilkes-Barre, Pa. (communication to the Secretary*):—Mr. Stow's paper presents a series of arguments, numbered from 1 to 18, concerning the relative merits of four systems of colliery-ventilation, designated by the author as " plain pressure-ventilation," " plain exhaust-ventilation," " obstructed pressure-ventilation," and " obstructed exhaust-ventilation." These arguments are subsequently compared by means of tables, in which an arbitrary numerical value is assigned to each, and which consequently serve no other purpose than that of showing his opinions and predilections, as indicated by his assignment of the said numerical values. In addition to this general summary, Mr. Stow intimates his preference for a fifth method of colliery-ventilation—namely, what he calls " alternating pressure-ventilation," which consists in the running of the fan at "pressure " during working-hours, and as an " exhaust" between shifts—a system which he proposes as, perhaps, new, yet which he thinks deserves recognition " as a standard form." This proposed " standard form " is not to be found in practice ; and I think it would be impracticable in gaseous mines of large extent, for the following reasons: 1. It takes considerable time to reverse the air-current in a large mine; and the reversal would involve a period of complete stoppage of ventilation, long enough to permit serious accumulations of gas. 2. In shaft- and slope-mines, at least, it is hardly practicable to have " every man out of the mine" during the night, and certainly impracticable to avoid keeping mules and horses inside. 3. The doors necessary to divide and direct the air-current are properly hung to open against the air-pressure; and, unless

Jan 1, 1910

By H. P. Allen

THE Achotla mill of the Cia. Minera de Pe[n]oles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation Of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1937

By Alfonso Rizo-Patrón, A. M. Gaudin

PREVIOUS studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector. The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest. In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector. The results obtained indicate that a I : I ratio of collector ion to activator ion gives optimum results, and that a 2:I ratio almost fails to achieve activation and flotation. Yet, a 2:I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion. To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful. The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids; they confirm that an adsorbed coating is inescapable. APPARATUS AND SUPPLIES The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz. The flotation machine was built according to the design of D. W. McGlashan.* It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel stator, as in the Fagergren laboratory machine. The air intake is controlled by a valve, and the cell consists of a beaker. The quartz was obtained from vein quartz stored in large chunks. It was first crushed to 20 mesh, then sized on a 28-mesh screen. The 20 to 28-mesh size alone was retained for use. This size was freed of coarse iron by passage through a Ball Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used. The barium was used as barium chloride, Baker's analyzed C. P. The oleate was used as sodium oleate. It was prepared from sodium hydroxide, Baker's analyzed C. P., and oleic acid purified by R. R. de Arellano3 in the laboratories at the Massachusetts Institute of Technology. The purification procedure was elaborated from the recent researches of Brown and Shinowara.2 It consisted in: (I) saponification of olive oil with potassium

Jan 1, 1942

By Floyd C. Kelly

There is an ever-increasing demand for furnaces with controlled atmosphere, due to the large quantities of steel being used in the automotive industry, such as the high-chromium stainless irons, the 18 Cr, 8 Ni stainless iron and low-carbon steel sheets. The difficulties involved in the annealing of such materials, if they are to be kept absolutely free from oxidation, are many. It is possible to bright-anneal these steels in small laboratory hydrogen furnaces, using specially purified hydrogen and taking some additional precautions. In the first place, the insulation, usually of alumina or magnesia, holds small amounts of water vapor, which it is almost impossible to remove completely. Secondly, there is always condensataion of water vapor in the cooling chambers of such furnaces, and with the continuous circulation of the hydrogen gas in the furnace, the water vapor is carried from the cooling chamber back into the heating chamber. This water vapor oxidizes the charge. Lastly, the supply of moisture is made sure by the diffusion of small amounts of air from the atmosphere into the furnace against the pressure of the hydrogen. The oxygen combines with the hydrogen and forms more water. Under such conditions there is little gained by using specially purified gas, because it becomes contaminated after reaching the furnace. Low-carbon Steel If a sheet of low-carbon steel is annealed in such a furnace at 750" C. and allowed to cool with the furnace, an adequate flow of purified hydrogen being maintained all of the time, the steel will come out with a very thin coating of blue oxide. If a similar sheet is annealed at the same temperature and quickly pushed into the cooling chamber, it will come out nearly bright, or perhaps with only the edges slightly discolored. It is difficult to get a piece of steel through a furnace of this type with an absolutely bright surface. This is due to the fact that there are always traces of oxygen or water vapor in the furnace. When the steel is allowed to cool with the furnace, it reaches a critical temperature where the affinity of iron for oxygen is greater than that of hydrogen for oxygen, and the steel comes out discolored. If the steel is pushed from the hot zone

Jan 1, 1931

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943

By C. W. Washburne

THE waters of many oil fields have been regarded as buried sea water which has been retained in the sediments since the time of their deposition. The preservation of connate water through geological time has seemed improbable to only a few geologists, but there is room for doubt that buried sea water could remain in the strata during their periods of deformation and during the many subsequent epochs of. the circulation of meteoric ground-water. Some have even suggested that the calcium chloride water in the deep mines of the Lake Superior region is ancient sea water buried in the Algonkian lavas, but it is hard to understand how such water could be derived from the highly sodic and sulphatic water of the sea. It would seem more plausible to connect the calcium chloride with the highly calcic magmas of the greenstones in which it is found. Chemical analyses of waters associated with oil differ widely from the composition of sea water, requiring extensive alteration of the latter, if the former is truly its derivative. The first notable difference is the general absence of sulphates from oil-field waters, but this has been explained satisfactorily through reduction by hydrocarbons and organic matter. Oil reduces sulphates with the production of hydrogen sulphide (or sulphur), water, and carbonates (or carbon dioxide). The second striking difference is in the high ratio of chlorine to sodium. An examination of the analyses of chloride waters from oil fields shows that they contain a large relative excess of chlorine over that in sea water. Moreover, there is difficulty in finding chemical reactions that are probable in nature, by which sea water could be converted into anything like the chloride waters of oil fields. In the latter a large part of the chlorine occurs as calcium acid magnesium chloride. This condition might be produced by the removal of sodium carbonate, which; however, cannot be precipitated in the presence of much calcium or, magnesium.

Jan 3, 1914

By S. Weinig, E. S. Machlin

THE mechanism of the martensitic transformation has been the subject of a remarkable number of papers in recent years.' Because the task of evaluating all the available theories is a formidable one, the authors will confine themselves merely to the presentation of results of an experimental investigation of the habit orientation, lattice relations, magnitude and direction of average transformation shear strain, and orientation of subband markings for a single variant of the possible habit systems in an 11 pct Mo-Ti alloy. It is hoped that these data will assist in the establishment of a rigorous theory for the mechanism of the martensitic transformation. Experimental Procedure Specimen Preparation: A sample, approximately 1/2 x 1/4 x 1/4 in., was cut from a double arc-melted ingot composed of commercial-process A titanium and high purity molybdenum (nominally, 11 pct Mo). It was capsuled in evacuated Vycor at 10.-3 mm Hg subsequent to a double argon wash and homogenized for 48 hr at 1100°C. After a direct quench into H2O at room temperature, a large-grained specimen resulted, which, by X-ray diffraction and metallographic means, was subsequently shown to be in the body-centered-cubic phase, ß. Two adjacent, approximately perpendicular faces were polished and the ends of the specimen were ground parallel in a V-block. Fiducial lines were inscribed at 45" to the common edge of the polished surfaces in order that they would be perpendicular to the habit traces of the subsequently formed a plates.2 The specimen was then compressed between the ground ends in a Buehler press to stress induce the transformation ß to a'. Experimental Measurements: The habit-plane orientation, the orientation of subband markings, the orientation relation between the parent ß and the product a', and the transformation strain for the same plate were determined. To further establish the nature of the subbands, one surface was repol-ished and etched. The bands in the a' were still visible and were found to be optically anisotropic under polarized light. Back-reflection Laue patterns were obtained from the ß matrix and from a region comprising both a' plates and adjacent ß matrix (a Cu target was used). By superposition of the two X-ray diffraction patterns, it was possible to obtain a tentative orientation relationship between the two phases. This result was confirmed by a pattern taken after the specimen was rotated to make the basal-plane pole of the hexagonal a' phase strike the film. This necessitated cutting the specimen to expose the a' plate in the new position relative to the X-ray beam. Analysis of Experimental Measurements On the basis of the aforementioned X-ray patterns, the orientation between parent and product

Jan 1, 1955

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year's total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year's operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas' largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year's total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year's operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas' largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

By Sherwin F. Kelly

The need for geophysicists to adopt a uniform mode of expressing the electrical resistivity of geological formations has been stressed by Dr. A. S. Eve.1 The present paper is to emphasize the point he raised, to bring the weight of disinterested authority to bear on the matter, and to urge the adoption henceforth, save in exceptional cases, of a standard expression for resistivity; all in the hope that the needed reform will thus actually be brought about. The general definition of the resistivity of a material is the resistance in ohms between two opposite faces of a unit cube of that material. No account need be taken here of the cases in which the unit volume is not a cube, and the units of length and cross-section are different, encountered principally when dealing with metallic conductors such as wires. The idea of the resistance of a unit volume of earth or rock has found expression in geophysical literature in a number of forms and with a variety of units. Fortunately, the metric system has been adhered to in most cases, so ordinarily the meter or the centimeter, usually the latter, has been the measure chosen. The resistivity is then the resistance of a cube of the given rock, or soil, one centimeter on an edge. This is far from always being the same thing, however, as the resistance of a cubic centimeter. A long thin wire could contain a cubic centimeter and have a high resistance, whereas the same volume formed into a flat plate would have an entirely different, and quite low, resistance between faces. Consequently, it is not proper to express resistivity in ohms per cubic centimeter, inch, etc., as has been done occasionally by some writers. In an effort to emphasize the idea of cubic volume, some geophysicists, the writer among them, have used the phrase, ohms per centimeter cubed. This is a graphic way of picturing the measure, but is not in favor among highly qualified authorities. In this connection, an appeal was made to the U. S. Bureau of Standards for advice, and the Director, George K. Burgess, kindly replied in detail as to the practice adopted by his Bureau: 'I.., such expressions as 'ohms per centimeter cubed' or any similar expressions are objectionable, because they certainly carry the implication that the resistivity is found by dividing ohms resistance by the volume in cubic centimeters." Actually, of course, resistivity is found

Jan 1, 1932

By C. E. Birchenall, R. H. Condit, M. J. Brabers

In the oxidation of pure iron above 700°C the overall rate is determined mainly by the rapid growth of wiistite, through which iron ions can diffuse rapidly.' Nickel added to the iron progressively decreases the stable range of composition of wustite.' When enough nickel is added to eliminate wiistite as a stable phase, the spinel is the fast growing phase. This investigation was undertaken to test the hypothesis that nickel substituting for iron in magnetite might decrease the rate of spinel growth by reducing the iron mobility. Nickel ferrite boules grown by the flame fusion process were purchased from the Linde Co. Chemical analysis gave an atomic ratio of iron to nickel of 2.88 and showed no other cations. They were cut into discs and ground to give flat, parallel faces. The experimental procedure employed was like that of Eisen and Birchenall in which the distribution of radioactivity diffused in from a vapor deposited surface layer was determined by counting the residual activity through a series of ground faces. The diffusivities were calculated in a manner consistent with the requirements discussed by Condit and BirchenallP The details will be given in connection with a more extensive spinel diffusion study now in progress. The results of the measurements are shown in the figure in comparison with earlier data on magnetite1 and zinc ferrite. The uncertainties arising from scatter in the activity vs distance relationship and uncertainties in the temperatures are shown by flags. Despite the scatter it is clear that substitution of a considerable part of the iron in magnetite by nickel, in this case about one third decreases the iron mobility substantially. sachs' determination of the distribution of iron and nickel in scales on iron-nickel alloys appears to show that nickel is less mobile than iron in the spinel layer. It is evident, therefore, that nickel plays several roles in reducing the oxidation rate of iron-nickel alloys. 1) It reduces progressively the stability range of wiistite. ' 2) It reduces progressively the stability range of the iron-nickel spinel phase in terms of the variation in cation to anion ratio.' 3) As shown in this investigation, it reduces the cation mobility in the spinel phase which is the faster growing phase in the absence of wiistite. The fe was obtained from the Oak Ridge National Laboratory. The research was supported by the Air Force Office of Scientific Research (ARDC) under contract number AF 18(600)-967.

Jan 1, 1961

By J. W. Powell

A Federal statute, enacted several years since, provides for the preparation of a geologic map of the United States. There are three requisites for a geologic map. The first is a suitable base- or surface-map upon which the rock-formations may be platted by means of conventions ; the second is a classification of the rocks and formations, and the third is a system of conventions by which the rocks and formations may be represented on the map. When the work of the Federal bureau created to prepare the geologic map was commenced, a topographic survey of the country was undertaken for the purpose of making maps suitable for the use of geologists in the field and for the representation of the geology; and this work has ever since been continued. The surveys have now extended over about one-fifth of the national domain, and are mapped on a series of atlas-sheets, each constituting a section of the great map of the United States. About 700 of these atlas-sheets are completed. They are in extended use among engineers, miners, prospectors, map-publishers and educators, and are thus widely known; moreover, these base-maps have been exhibited, described and discussed at meetings of the Institute, and thus do not require detailed consideration. Classification of Bocks and Formations. Modern classification is designed to express natural relation. In the beginning of observational science, or natural science, objects were discriminated and grouped by differences and resemblances; but at first the differences and resemblances recognized in the classification were external, even superficia1,'and often confined to single features. Later, groups of features and characteristics, both external and internal, were recognized as the basis of classification ; and of recent years, throughout the entire domain of biology, and to a considerable extent in the kindred sciences, classification is based not

Jan 1, 1893