Search Documents

By T. L. Joseph

S. T. Killian (Johnstown, Pa.)—This is one of the finest papers I have read. Tying in stoichiometric calculations with furnace performance and practice is a step which had to be taken sooner or later. The noteworthy difference between Dr. Joseph's type of calculations and regular blast furnace calculations is that the Ib mol system is used as a basis. With the Ib mol system, weights, volumes, and chemical reactions can all be expressed in the same equation. In the paper, wind, ore, flux, and fuel are all expressed as lb or lb mols. Probably Dr. Joseph does not realize it, but the vague word coke appears only twice in the entire paper. Lb of C and Ib mols of C are followed through reactions but the word coke appears only as 1560 lb coke per ton of pig and 1700 lb of coke per ton of iron. Obviously in order to understand furnace reactions, the coke should be expressed as lb or lb mols of C. Furnaces can also be compared more easily. In some respects the paper is too thorough and too complete. The effects of the metalloids reduced into the iron upon the top gases represents a difference of less than 3 pct of the CO formed in the bosh. Due to the completeness of the calculations in relation to the CO/CO2 ratio, this was included and was necessary. However, the exclusion might have enabled more furnace men to follow the lb mol system of calculations through the blast furnace to a better degree. By considering only irons of similar analysis, this part of the calculations might have been omitted. However, if this had been done, total rewriting of the paper later would have been necessary in order to make the work complete as it is now. It also would not have been nearly as authoritative. In the paper, there appears the reaction: H2O + CO ? CO2 + H2 [I] Dr. Joseph states that he did not take this reaction into consideration in any calculations pertaining directly to the paper. The piobable reason- for this is that although it contains all the main reacting top gases except N2, it is rather inflexible since it is monomolecular in relation to each of the reacting gases and does not tie in with the gasification of C. Actually the reactions: H2O + C ? CO + H2 [2] 2H2O + C ? CO2 + H2 [31 and the solution loss reaction: CO2 + c ? 2c0 [41 tend to assume an equilibrium through the reaction: H2O + CO ? CO2 + H2 [I] which should be considered a balancing or equilibrium reaction. Reactions 2, 3 and 4 permit furnace conditions to balance with the CO/CO2 ratio and H2 formation. They tie in with the solution loss. Reaction 1 unites them chemically. Probably the best calculation to make at this time would be to try to find the relative importance of the CO2 from the flux and the H2 in the dilution on an actual furnace gas analysis. For this purpose the Dob-scha-Carnegie-Illinois paper—"Effect of Sized and Sintered Mesabi Iron Ores On Blast Furnace Performance" is chosen. This paper was presented before the blast furnace section of the AIME in 1948. This represents the best large scale furnace operation available to me. Unfortunately the changes were brought about by beneficiation of the burden and not by changes on one burden. In choosing the basis for the calculation in relation to the furnace, 100 mols of dry top sgas is chosen. This leaves something to be desired inasmuch as the nitrogen basis is changing but I believe it will be better understood than any other type and it is the easiest to use.

Jan 1, 1952

By D. J. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent papers. 1.2.3.1 In those papers references were also given to the work of Haigh in 1917.6 Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper .2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and nonferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far

Jan 1, 1928

By G. Donald Emigh

Nothing is more important to life-plant and animal-than phosphate. Its compounds are essential to the energy functions of all living systems and for the formation of bones and teeth. Animals get their phosphate from eating plants and other animals, or domestically from feed supplements. Plants get their phosphate from the soil. Man's most important use of phosphate is for fertilizer; however, he is also a heavy user of many industrial phosphate chemicals. Phosphate occurs in all igneous and sedimentary rocks, and in all fresh and saltwater. The average content in rocks is 0.1 to 0.2% P2O5, as documented recently by McKelvey (1973). About 200 minerals contain more than 1 % P,O,. However, the important one in igneous rocks is fluorapatite, (Ca,(PO,) ,F) containing about 42% P,O, and 3.8% F,; in sedimentary rocks the one important mineral is francolite, a carbonate fluorapatite containing up to 2% molecular CO,. Both are in the apatite family of minerals. The mineralogy of phosphate minerals was reviewed recently by Altschuler (1973). Although phosphate occurs in nearly all rocks, economic recovery is limited to deposits where natural concentration of the phosphate mineral has occurred. Occasionally natural concentration is great enough that the material can be used as mined; generally, however, the ore is low grade and must be concentrated.

Jan 1, 1975

By H. B. Fuqua, B. E. Thompson

For a very brief description of the North Texas area and the general geological features with which it is associated, the reader is referred to the summary for 1935. As in previous years, the authors have been unable to undertakc the almost impossible task of isolating statistics for the hundreds of productive "spots" which are included within the generally productive areas of the several counties. However, pools that appear to be definitely isolated—as, for example, the Foard County production and the new pool recently developed southeast of Gainesville in Cooke County—are covered separately. During the year 1936, both routine development in proven or scmi-proven areas and exploratory drilling showed a decrease over the year 1935, there having been a total of 1453 wells drilled in the district during 1936, as compared to 1619 in 1935. It is also of interest to note that abandonments exceeded completions in 1936. Developments during 1936 While a number of local productive spots were found in Wilbarger, Archer and Wichita Counties, and numerous minor local extensions to older producing areas were developed in practically all the producing countics in the district, only two discoveries of sufficient importance to justify special mention were made. Anderson and Kerr No. 1 Bruhlmeyer, about two miles southeast of Gainesville in Cooke County, was completed in April, at a total depth of 2014 ft., for an initial production of 315 bbl. daily from a sand of Pennsylvanian (Canyon) age. Development has been rapid and the field is about drilled up. During November the 100 wells in the field averaged about 40 bbl daily. The structure appears to be a small fold associated with the northeast flank of the main uplift, which extends in a northwest-southeast direction across Cooke and Montague Counties.

Jan 1, 1937

By Arthur C. Simmons

The area that produces Pennsylvania grade, which includes New York, Pennsylvania, West Virginia and a part of Ohio, increased its production in 1942 about 1,580,000 bbl. over that attained in 1941. Such an increase is substantial for this area, and measured in terms of increased output of lubricants, for which the crude is particularly suitable, it represents a needed arid worth-while addition to the lubricant resources of the United States. The year 1942 was a difficult operating period for most of the petroleum-producing areas in the United States, but the Appalachian region, owing principally to its location, type of operations, and crude value, suffered less from war influences than other areas. The state of Pennsylvania produced 17,823,870 bbl. of crude oil, which is approximately 63 per cent of the total production of Pennsylvania grade in the entire area. Production Bradford Field The Bradford field, which produces almost wholly by water-flooding methods, increased its production nearly 4000 bbl. per day over 1941 despite a very slight reduction in total number of wells completed. Well completions in the Bradford field (in both New York and Pennsylvania) includc both producing oil wells and water-intake wells. About half of the well completions are producing oil wells and the remaining half are water-intake or injection wells. About 10 per cent of the total well completions of the Bradford field were in Cattaraugus County, New York. No segregation of well completions is available, so that precise statistics cannot be given for New York and Pennsylvania.

Jan 1, 1943

By Arthur C. Simmons

The area that produces Pennsylvania grade, which includes New York, Pennsylvania, West Virginia and a part of Ohio, increased its production in 1942 about 1,580,000 bbl. over that attained in 1941. Such an increase is substantial for this area, and measured in terms of increased output of lubricants, for which the crude is particularly suitable, it represents a needed arid worth-while addition to the lubricant resources of the United States. The year 1942 was a difficult operating period for most of the petroleum-producing areas in the United States, but the Appalachian region, owing principally to its location, type of operations, and crude value, suffered less from war influences than other areas. The state of Pennsylvania produced 17,823,870 bbl. of crude oil, which is approximately 63 per cent of the total production of Pennsylvania grade in the entire area. Production Bradford Field The Bradford field, which produces almost wholly by water-flooding methods, increased its production nearly 4000 bbl. per day over 1941 despite a very slight reduction in total number of wells completed. Well completions in the Bradford field (in both New York and Pennsylvania) includc both producing oil wells and water-intake wells. About half of the well completions are producing oil wells and the remaining half are water-intake or injection wells. About 10 per cent of the total well completions of the Bradford field were in Cattaraugus County, New York. No segregation of well completions is available, so that precise statistics cannot be given for New York and Pennsylvania.

Jan 1, 1943

By E. E. Brownson

This paper will be confined to the treatment of methods as applied in the laboratory of the Boston and Montana Reduction Department of the Anaconda Copper Mining Co. at Great Falls, Mont. As the electrolytic plant of this company operates at a current density of approximately 35 to 40 amperes per square foot when running up to capacity, the arsenic and antimony content of the anodes delivered to the plant is of considerable importance as bearing on the purity of the refined cathodes turned out. Owing to the rather high relative percentage of antimony, it has always been the custom to determine antimony as well as arsenic in all forms of copper. Thus, anodes have been analyzed in which the antimony was about equal to the arsenic, although the average shows about 2 parts of arsenic to 1 of antimony. In the refined copper the relative proportions of the two impurities vary considerably, but probably in the average are about equal. In this latter case, the percentage of the two is SO small that ordinarily no attempt is made to separate them, the report of analysis showing percentage of As and Sb combined. Although rapid and exceedingly accurate determinations of arsenic may be made by means of various distillation schemes, the determination of antimony, either by itself or together with arsenic, has always been more or less cumbersome and has required a considerable amount of time. By the methods, details of which follow, the determination of arseluic and antimony, either separated as in the case of anodes or together in case of refined copper, is accomplished in 24 hr. from the time the sample is received by the chemist. As to the accuracy of the results obtained, it can be quite positively stated that in this respect these methods are very satisfactory, much more so than any heretofore employed in our work, and when the rapidity of determination is considered, the results are very accurate.

Jan 1, 1914

By C. C. Clark, J. S. Iwanski

The purpose of this investigation was to study mi-crostructural changes that take place in a commercial nickel-chromium-iron alloy, such as Incoloy "901," over long periods of time at temperatures up to 13 50°F and to correlate such changes with creep-rupture properties. of the alloy. In the course of the investigation, some microstructural changes were observed which correspond to microstructural alterations found in previous studies of Inconel "X." Microstructural phases have been identified in both alloys with the aid of electron and X-ray diffraction and an electron probe microanalyzer. The materials used in this investigation were from commercial heats of the following chemical composition: Pct Cr Pct Ni Pct Mo Pct Fe Pct Cb Incoloy "901" 12.51 43.67 5.72 Bal. -Inconel "X" 14.61 73.44 - 6.61 1.02 Pct A1 Pct Ti Pct Mn Pct Si Pct C Incoloy "901" 0.10 2.46 0.46 0.24 0.05 Inconel "X" 0.70 2.43 0.51 0.36 0.04 Long-term creep-rupture tests were conducted on Incoloy "901" at temperatures of 1000°, 1200°1 and 1350°F. A summary of these results is shown in Table I along with the results of a long-term creep-rupture test conducted on Inconel "X" at 1500°F. The heat treatments given the specimens are also shown in Table I. When the creep-rupture results on Incoloy "901" are compared with shorter-tertn data, there is no evidence of any undue deterioration of the creep-rupture strength with time, nor is the elongation decreased more than would be expected from the influence of time alone. INCOLOY "901" PHASE IDENTIFICATION Microscopic examination of the Incoloy "901" specimens reveals a dark etching grain boundary constituent in the specimen which was under test for about 11,500 hr at 1000°F. This grain boundary constituent was seen to increase in size as the test temperature was increased to 1200" and 1350°F, Figs. 1, 2, and 3. Simultaneously, an acicular structure of definite crystallographic orientation appears within the grains of the 1350°F specimen, Fig. 3. Under examination with the electron microscope, a fine precipitate is observed in the 1200 °F specimen. Fig. 4. It becomes considerably larger in the 2850-hr 1350°F specimen, Fig. 5. In a few areas the precipitated particles have been replaced by, or transformed to, small needles or platelets. After 7380 hr at 1350°F, Figs. 3 and 6, the needles are much larger and have replaced nearly all of the fine precipitate. X-ray diffraction studies detected the presence of hexagonal Laves phase and hexagonal n phase (Ni,Ti) in the 1350°F specimens, Table 11. Only the Laves phase was detected by X-ray diffraction in the 1200°F specimen and none was detected in the 1000°F specimen. In this latter specimen, however, the small quantity of precipitate in the grain boundaries (presumed to be Laves phase) precludes its detection by X-ray diffraction. Composition of the hexagonal Laves phase is not yet known, although its diffraction

Jan 1, 1960

A joint statistical report released by the U.S. Department of Commerce and U.S. Securities and Exchange Commission indicates that business investment in new plants and equipment is expected to total $81.8 billion during 1971. This figure is based on the findings of a survey conducted in late April and May and reflects about a 1 ½ % decrease in investments from the $83.1 billion projected in February. Mining, on the other hand, is still in a bullish mood and is expected to spend $1.99 billion in 1971 compared to $1.89 billion in 1970 and $1.86 billion in 1969. Based on figures quoted above, mining investment in 1971 should show a 5.2% increase over 1970. Carl E. Bagge, president of the National Coal Association, was the dedicatory speaker at the new Milton R. Young Station of the Minnkota Power Cooperative in North Dakota. This new power plant incorporates many innovations which have overcome the problems of using the low-cost lignite abundant in the area. According to Bagge, this development and President Nixon's recent request for an extra $10 million for coal gasification plants is helping the region lead the way in providing for the power needs of the future. He also maintains that gasification of coal can reconcile coal consumption with the demand for cleaner air, and also assure the nation of adequate pipeline gas.

Jan 1, 1971

As will be noted from the paper following, the sampling and estimating of limestone replacement deposits is entirely different from such work on a vein or disseminated ore deposit.

Jan 1, 1925

By W. C. Hagel, J. H. Westbrook

THERE has been a recent revival of interest in the intermetallic compound AgMg as an experimental material for study of the physical and chemical properties of simple ordered structures. Studies of mechanical behaviors,1-4 diffusion,5,6 and thermo-dynamic properties7'8 have been reported. In several of these studies, heat treatments have been carried out in argon-filled silica capsules at temperatures as high as 750°C with no apparent adverse effects. The present authors were, therefore, startled to discover in the course of some yet unpublished work, that gross melting of near-stoichio-metric AgMg compositions occurred in such samples more than 100 deg below their melting point of about 800°C. This note is to report a brief series of experiments carried out to establish the reason for this behavior. Gross errors in sample composition and failure of furnace temperature controls were quickly eliminated as causes of melting. The first tangible lead came from chemical analysis of an AgMg sample which had melted during treatment at 750°C. A silicon content of 3.3 wt pct was found. Since satisfactory analyses had been obtained on the original as-cast ingot, contamination by diffusion and/or reaction with the fused silica capsule seemed a distinct possibility. A perplexing fact, however, was the apparently capricious incidence of the effect. Not only was it previously unknown, even in the experience of the present authors; but, in the early part of the present study, melting sometimes occurred and sometimes not with specimens treated under constant conditions. Indeed, one sample successfully survived a 750°C heat treatment and yet melted completely during the course of a subsequent anneal in an identical capsule at a lower temperature. To obtain evidence that silicon contamination could lower the melting point to the extent observed, the following experiment was performed. A series of ternary alloys was made up with a stoichiometric AgMg base and containing 0.1, 0.2, 0.4, 1, 2, and 4 wt pct Si. Melting was done in MgO crucibles under a cover of argon gas. After holding 10 to 20 min in the temperature range 850° to 900°C, the alloys were allowed to solidify in the crucible and the temperature during cooling automatically recorded with a Pt/Pt-10 Rh thermocouple. Results from the cooling curves are shown in Fig. 1. Checks within 2 to 5C° were obtained upon repeated melting, cooling, and freezing. The whole series of cooling curves as well as metallographic examination of the melted alloys established that the AgMg rich portion of the AgMg-Si quasibinary is an eutectic-type system. The melting point of AgMg is lowered from approximately 820°C in the pure stoichiometric binary9 to about 710°C in the saturated intermetallic phase. Since second phase was observed in all samples on cooling to room temperature, the solid solubility of AgMg for silicon evidently falls rapidly with decreasing temperature as indicated schematically by the dashed solvus in Fig. 1. It is thus established that a silicon content

Jan 1, 1963

By Marsh S. Watson, Robert A. Howard

An electrolytic model study has been made of the relative productivity of perforated casing. The results show that the relative productivity is roughly one-half to two-thirds of that predicted from point-sink calculations. This discrepancy can he satisfactorily explained on the basis of casing interference. The relative productivity was found to he insensitive to spatial arrangement of the perforations. INTRODUCTION The relative productivity of wells with perforated casing has been treated mathematically by Muskat.' In his treatment the perforations are represented by small spheres, thus enabling him to approximate the flow by that to point sinks. By neglecting interference between the flow into the various spheres representing the perforations, one may deduce the approximate formula Qu 1/rp - 1/rw • (1) I + b/2n _________ 2n In re/rw Where Q is the flow rate into spherical sinks located in the median plane of the sand laver Qo is the open hole flow rate (uncased hole of radius rw) b is the thickness of sand layer under consideration (always one foot in this paper) n is the number of spherical sinks in the sand layer rp is the radius of a spherical sink rw is the well radius re is the drainage radius of the well. Fig. 1 is a comparison of values calculated from equation (1) with Mus-kat's values. It will be observed that the approximate values are in error by less than 21/2 per cent. The disturbing effect of the casing on the flow line; is not explicitly taken into account by Muskat, but he reasons that interference between the flow pat- terns from the various point sinks will result in a negligible flow in the region within the well radius, and that no appreciable error will result from not explicitly excluding flow from this region. This line of reasoning is open to question, however, as the flow impedance, in the immediate vicinity of the well, of a hemispherical cavity in contact with an opening in the casing is twice that of a spherical sink in a continuous sand layer. There will be a difference, moveover, between the flow into a hemispherical cavity and that into a circular hole in the casing. .This latter difference can best be appreciated by comparing the flow from a semi-infinite medium into a hemispherical cavity at the edge of the medium with the flow out of a circular opening of the same radius as the hemisphere and which is also on the edge of the medium. In this case2 ------= —2, showing that the difference in flow rates into differently shaped cavities is quite appreciable. It was the purpose of the investigation reported here to determine to what extent flow into circular perforations in casing departs from the values calculated by Muskat. For this purpose an electrolytic model was used.

Jan 1, 1950

New York Meeting, October 16 and 17, 1913.-The One Hundred and Sixth meeting of the Institute for the reading and discussion of professional papers will be held in New York City, on Thursday and Friday, October 16 and 17, 1913. Headquarters will be at the Institute office in the Engineering Societies Building, 29 West 39th Street. The sessions will be held in one of the assembly rooms of the building. Because of the many valuable papers on iron and steel obtained with the assistance of the Iron and Steel Committee, which papers could not appropriately be presented and discussed at the Montana meeting, this October meeting of the Institute is held for the purpose of reading and discussing these papers, most of which will be printed and distributed in advance. The members of the following societies have been invited to attend the meeting, and several have accepted and declared their intention of taking part in the proceedings: American Society for Testing Materials, American Iron and Steel Institute, American Society of Mechanical Engineers, American Society of Civil Engineers, American Institute of Electrical Engineers, American Foundrymen's Association. The meeting will be conducted under the auspices of the Iron and Steel Committee, and the latest revised program of the proceedings will be found on page xi, under the notes of this Committee.

Jan 10, 1913

The age of specialization has made man increasingly dependent on a larger number of different metals and minerals. Overexploitation during World War II and lavish squandering of irreplaceable mineral wealth in the past has resulted in the rapidly approaching exhaustion of some of the major domestic ore sources. History clearly points out that the United States cannot continue to be a world power on an "import to survive" policy. A constructive program of development and appraisal of the nation's mineral wealth, including the planned conservation of her resources, must be adopted. Strictly speaking, conservation of minerals must mean the orderly exploitation of our resources and the prevention of waste in use, with due regard for the future. Real concern for the future may not extend beyond a few generations. Eventually science and invention should take care of the problems arising from shortages of some minerals, and the national defense aspects of domestic deficiencies can be provided for by stock piling and other measures. Early conservationists had this viewpoint; but with a rapidly developing industry and population, a farsighted policy that would deny full realization of immediate ambitions became unpopular. Consequently, the politically minded conservationist broadened the concept to include "prudent use of resources" and brought under the conservation umbrella

Jan 1, 1950

By R. W. Prouty, R. T. Green

The object of this paper is to describe, as concisely as possible, the methods of sampling and ore estimating used at the Copper Queen Branch, Phelps Dodge Corpn., as applied to the Copper Queen mines at Bisbee, Ariz. Because of the difference in occurrence, manner of prospecting, and methods of mining, the sampling and estimating practice falls into two divisions: That for the underground operations, and that for the Sacramento Hill steam-shovel operations. The orebodies of the Warren district may be divided into three main classes: Replacements of limestone, replacements of porphyry, and replacements of contact breccia. The first class is more or less intimately related to porphyry intrusions, although in badly fractured country this relationship may not be well shown. These orebodies are mainly oxide and carbonate ore and very irregular, both in size and outline, although usually roughly lenticular and following the bedding of the limestones. There is usually quite a sharp boundary between the ore and waste in the carbonate and oxide orebodies and sampling is not necessary to determine the limits of commercial ore. In the sulfide orebodies, it is exceedingly difficult, without sampling, to determine the boundary between commercial ore and the surrounding low-grade or barren pyrite. Calculations made a few years ago showed that these orebodies had an average thickness of 35 ft, As some of the orebodies are from 100 to 300 ft. thick, it can be seen that the smaller ones form a difficult prospecting and estimating problem. In the replacements in porphyry, both underground and in Sacramento Hill, the boundary usually cannot be determined without sampling. There is a gradual decrease in value until barren material is reached; this gradation may occur within a short distance or it may extend for several yards.

Jan 1, 1925

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

Jan 1, 1937

By Linn M. Farish

The reported production of petroleum in the Dominion of Canada for 1930 was 1,555,199 bbl., an increase of 455,373 bbl. over 1929. Alberta accounted for nearly all the production with Ontario and New Brunswick, the other two productive provinces, contributing less than 1 per cent, of the total. The completion of about 25 producing wells in Alberta was more than sufficient to offset the decline of the older wells in that province and the small decline in Ontario. The production of about 5000 bbl. in New Brunswick represents a restricted output to meet the market demand. Table 1 shows the production by provinces for the past 10 years. The consumption of natural gas for all purposes in Canada reached a new record of practically 40,000,000,000 cu. ft. in 1930, which was a considerable increase over 1929. The estimated value of the gas output was $10,500,000, against a little over $5,000,000 for the total petroleum production. Gas wells in Alberta accounted for over 75 per cent. of the total, with Ontario second and New Brunswick a poor third. The outlook for 1931 is for very little change in production of either gas or oil in Ontario and New Brunswick but for a substantial increase in both in Alberta.

Jan 1, 1931

By C. M. Tucker, Kent R. Van Horn, W. P. Sykes

RECENT investigations of the molybdenum-carbon alloys have been reported by Becker and Ebert1‡, Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metallographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-fish intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. METALLOGRAPHIC INVESTIGATION A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500° to 1600° C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively

Jan 1, 1935