Search Documents

By E. P. Jennings

The iron-ore deposits of Iron county, Utah, which rival those of Lake Superior in extent, are situated 275 miles south of Salt Lake City, and 25 miles south of Lund, a station on the San Pedro, Los Angeles & Salt Lake railroad. The range of hills containing the deposits has a general NE-SW. strike, and rise from a few hundred to 2,000 ft. above the Escalante desert, the ore being included in an area of 5 by 20 miles. The basal rock of these hills is diorite-porphyry. The flanks of the range are covered with limestone supposed to be of Carboniferous age, underlain in some localities by quartzite. Both formations are conformable to the porphyry, and are the remnants of beds that formerly covered the highest peaks, but have been removed subsequently by erosion. In the central and southern parts of the range, beds of Cretaceous sandstone rest unconformably on the eruptives. Rhyolite-flows occur to the south and southeast of the iron-ore deposits; and dikes and sheets of post-Tertiary lava are common. With the exception of a few springs, the range is destitute of water. Sage-brush, stunted cedars and the common desert-bushes constitute the only vegetation. Large beds of coal of poor quality occur in Cretaceous sandstones 15 miles east of the ore-deposits.

Jan 1, 1905

By Jackson R. Pellett

INTRODUCTION The Friedensville mine is situated in Upper Saucon Township, Le- high County, Pennsylvania, in the southern central part of the Allentown quadrangle of the United States Geological Survey, approximately 5 miles southeast of the City of Allentown and 4 miles south of the City of Bethlehem. Zinc was first discovered in the Friedensville area early in the 19th century and several mines were operating during the latter part of the century. Zinc oxide was produced in 1853 and zinc metal in 1859. All mining in the area ceased in 1893 chiefly because of an unfavorable economic situation caused by a severe ground water problem and competition from the higher grade ores in New Jersey. Property acquisition by the New Jersey Zinc Company began in 1899 and periodic exploratory drilling was carried on until 1940 when sufficient reserves were proved for development of a mine. Shaft sinking was undertaken in 1947 and, due to severe hydrologic conditions, was not completed until 1952. Production began in 1958 and today the mine is producing about 64,000 tons of zinc concentrate per annum. The concentrates are trucked to the Company's smelter at Palmerton, Pennsylvania, approximately 30 miles north of Friedensville. The mine also produces from its mill tailings industrial and agricultural grades of limestone for commercial markets.

Jan 1, 1970

Jan 1, 1941

By K. Stout, E. Van Eeckhout, L. Friel

Previous research at the Montana College of Mineral Science and Technology indicated that it is practical and economically feasible to place stiff back- fill in a cut-and-fill stope. This backfill would reduce wall closure and high stress buildup in pi1llars, thus alleviating rockburst potential. Three ;topes from the Sunshine Mine, of the Coeur d’Alene Mining District, were chosen for a test verification of this concept. Although the first stope was lever mined beyond the initial cut (for economic reasons), some vibrating wire stressmeter results were obtained and found to compare favorably with numerical predictions. Some other instrumentation devices were built and tested, but never installed .

Jan 1, 1984

By Esteban Domic, Eugene O. Brimm

The Lo Aguirre ore deposit of Sociedad Minera Pudahuel is expected to have a life of 12 years, producing 16,500 mt per year of copper cathodes. The total copper content of the ore ranges from 2% in acid-soluble form to 2% as sulfides. Sociedad Minera Pudahuel chose TL leaching, solvent extraction, and electrowinning as the processing steps to give low investment and operating costs. Design and operating criteria of the TL leach plant have been obtained in an experimental program carried out since 1974. Bench scale tests indicated that 90% of the oxidic copper and 35% of the sulfidic copper could be extracted to give 5 gpl copper by treating crushed ore with acid, curing, and rinsing in a column with a dilute acid solution containing ferric sulfate which is requllred to solubilize the sulfides. These results were verified in a pilot plant which combined leaching, solvent extraction, and electrowinning. Raffinate was recycled to the leaching circuit after oxidation to regenerate ferric ion. Refinements in the processing have resulted in significant improvements in extraction to give 95% to 98% recovery of the oxidic copper and 55% and 60% of the sulfidic copper. The plant is expected to give this degree of recovery. As a consequence, the original plan to include a concentrator in the plant has been abandoned.

Jan 1, 1980

By Keith E. Robinson, Brian Stimpson

INTRODUCTION In inclined sedimentary strata slope failure may occur by sliding along bedding and along a discontinuity or weak zone, as illustrated in Fig. 1. This mode of failure may be called 'bi-linear', as the failure surface is comprised of two linear or approximately linear segments. This type of failure has been suggested for the famous Frank Slide, Alberta, Canada (Cruder and Krahn, 1973) in which an estimated 90 M 5 tons (8.97 x 10 MN) of rock separated from Turtle Mountain and buried the town of Frank. Also, with the increasing depth of open pits and the construction of highways through inclined sedimentary strata this mode of failure is of major concern to the rock slope stability engineer. A computer program for calculating factors of safety for this slope failure mode is provided and includes the ability to vary shear strengths of potential slide surfaces, ground water elevations and wedge geometry. LIMITING EQUILIBRIUM MODEL The simple limiting equilibrium model used in the analysis is shown in Fig. 2. It is assumed that jointing is orthogonal to bed- ding and that the interface between the upper and lower wedges there- fore corresponds to a joint plane or planes. No shear strength is attributed to the interface so that the resultant force, P, from the upper wedge acts normally across the interface. The normal loads

Jan 1, 1983

By A. D. Zunkel, A. H. Larson

Equilibrium antimony contents of pb-sb alloys in contact with PbO-Sb2O3 slags containing less than 45 mole pct Sb203 uleve determined at 650', 700°, and 750°C in an inert atmosphere. In this ten~pevature range, the antimony contmzt of the alloy increased with increasing temperature at all slag compositions. The PbO-Sb203 phase diagram below 28 mole pct Sb2O3 was determined by thermal analysis and by application of a log sbZ4/y$b0 us plot determined from the equilibrium-activity data. The resulting phase diagram showed a eutectic at a temperature of 604°C and a comfiosition of 21.6 mole pct Sb2O, with a maximum terminal solid solubility of Sb203 in PbO of 5.6 mole pct. These results are compared with existing data in the literature. In the past three decades, only a small amount of experimental work has been done on the slag-metal equilibria in the Pb-PbO-SbaO3 or the analogous arsenic and tin systems. These systems are important in commercial lead-refining processes such as softening and dross fuming since it is impurities such as antimony, arsenic, and tin in lead bullion and Sb2O3, As2O3, and SnOz in lead drosses which must be re-

Jan 1, 1968

By Glenn C. Waterman, Scott Hazen

3.1-1. Purpose. Development drilling is directed towards determining the grade, volume, and three-dimensional outline of a mineralized zone previously located by exploration. It is distinguished from exploration or reconnaissance drilling, which has as an objective the discovery of new mineralized areas. A development drilling and bulk sampling program should furnish the following information: 1. Geology of the mineralized zone. 2. Quantitative data on grade and tons of material within pertinent cutoff limits. 3. Physical size and shape of the deposit. Areas underlain by waste as well as ore. 4. Mineralogica1 and metallurgical characteristics of the ore. 5. I1hysical characteristics of the ore. 6. Hulk samples for metallurgical testing and grade check. 7. Data on other factors that could affect mining operations, such as ground water, ground conditions, etc. 3.1-2. Procedures. There are numerous methods and techniques that are used to acquire pertinent data on a potential ore deposit. The total cost and accuracy of a development program depends on significant evaluation of the geology, proper selection of a drilling method, thorough analysis of sample data, and accurate evaluation of all the information. Knowledge of the geology of the mineral deposit is important in planning the development testing program and in evaluating the data obtained from such a program. Exploration work usually provides some significant information on the general size, shape, thickness, grade, and geology of the deposit. In some cases no further data are needed; in many cases geological complexities suggested by the preliminary work require further geological study. Of considerable importance may be the following:

Jan 1, 1968

The Institute published a collective index of- Volumes I to XXXV inclusive, which has been very extensively purchased and used by the members of the Institute. It enables one to look, up any subject in the first thirty-five volumes and is useful to those who have the Transactions, as well as to those who have not, because it tells what subjects have been treated and enables one to look these matters up in his own library and then afterward either to procure the individual papers from the Institute at the price of $1 each, or to procure Volumes, or to consult the Trans-actions at a nearby library, if such a one is available. It now seems desirable to publish another collective index, and the Editorial Department, upon the authority of the Board of Directors, has prepared an index of Volumes XXXVI to LV inclusive. This will be sold in the Institute's standard half morocco binding at a price of $5 and in paper covers at a price of $4. It wilt be ready in a few weeks. Those who already have the first index and purchase the second one, and those who purchase both, will have a complete index of the Transactions from Volumes I to LV inclusive. The Institute will be glad to receive advance orders for this index to insure prompt delivery upon publication.

Jan 8, 1917

CHICAGO SECTION CHAS. H. MACDOWELL, Chairman, LUTHER V. RICE, Vice-Chairman, HENRY W. NICHOLS, Secretary-Treasurer, GEO. P. HULST, ALEX. K. HAMILTON, FREDERICK T. SNYDER, HENRY P. HOWLAND. The Field Meeting of the Chicago Section proved to be the most enjoyable meeting ever held by the Section. It took the form of a visit to the Northern Indiana Industrial District where the day was spent inspecting metallurgical plants in Indiana Harbor and East Chicago and in amusement at the Hammond Country Club. The weather was perfect and about 50 members and ladies attended the meeting. An inspection of the plant of the Inland Steel Co. occupied the morning. The plant was decorated in honor of the occasion and the company provided attractive souvenirs. It was noticed here that many of the ladies displayed an interest in the inspection and an understanding of the processes that would not have shamed professional metallurgists. While the members of the Section seemed to be most interested in the by-product coke ovens and the by-product recovery plant, the ladies enjoyed especially watching the snake-like antics of the red-hot rods in the wire mill. Leaving the steel plant, the Section enjoyed a ride through the district by automobile and arrived at the Hammond Country Club in time for lunch. In the afternoon some of the members inspected the plant of the International Lead Refining Co., at East Chicago, while the rest spent the time at the Country Club in golf, tennis, trap shooting, bridge and other amusements. During the dinner at the Hammond Country Club an informally organized male quartette led the singing in real college boy style. In the evening, E. E. Billow talked on the use of oil burners in metallurgical furnaces, Mr. MacDowell told of the present status of the Potash Industry and the Secretary told of some of the happenings at the Arizona Meeting. HENRY W. NICHOLS, Secretary.

Jan 12, 1916

By J. L. Foster, G. R. Gray, T. S. Chapman

The wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as traga-canth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. Introduction It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.l-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-ll The wall-building properties of freshwater muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods gen-crally used in controlling filtration of freshwater muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. Laboratory Investigations Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester8 at a pressure of 100 lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 C.C. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1942

By G. R. Gray, T. S. Chapman, J. L. Foster

The wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as traga-canth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. Introduction It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.l-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-ll The wall-building properties of freshwater muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods gen-crally used in controlling filtration of freshwater muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. Laboratory Investigations Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester8 at a pressure of 100 lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 C.C. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1942

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent paper~.1,2,3,4 In those papers references were also given to the work of Haigh in 1917.= Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion-fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper.2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and non-ferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far

By G. R. Gray, T. S. Chapman, J. L. Foster

THE wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as tragacanth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. INTRODUCTION It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.1-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-11 The wall-building properties of fresh-water muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods generally used in controlling filtration of fresh-water muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. LABORATORY INVESTIGATIONS Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester' at a pressure of 10o lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 c.c. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1941

By Reed W. Hyde

SOME information has been published on the sulphur dioxide concentration of gases from Dwight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide flotation concentrates mixed with minus 20-mesh oxide ore, the mixture carrying 16.8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO2 might be utilized, a series of runs was made to determine the concentration of SO2 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1) 2 to 1 3/4 in., (2) 4 to 3 1/2 in. and (3) 6 to 5 1/8 in. The averages of the determinations from each series are platted on the graph (Fig. I). The vertical scale shows the percentage by volume of SO2 (as determined by the Reich method), and the horizontal scale shows the time expressed as percentage of the total sintering time. Sintering was considered to be complete when no SO2 could be detected in the gases. In all cases the depth of bed was 4 1/2 in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which SO2 determinations were made could not be measured, but has been calculated from the SO2 content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume will usually drop slightly toward the middle of the period and increase toward the end. However, this assumption is a reasonable approximation. Several interesting features are brought out by these data. In general, the published data on SO2 concentration in sintering under ordinary conditions show a high SO2 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SO2 in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum SO2 concentration is obtained 2 ½ min. after

Jan 1, 1942

By Reed W. Hyde

SOME information has been published on the sulphur dioxide concentration of gases from Dwight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide flotation concentrates mixed with minus 20-mesh oxide ore, the mixture carrying 16.8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO2 might be utilized, a series of runs was made to determine the concentration of S02 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1) 2 to 1 1/3 in., (2) 4 to 3 1/2 in. and (3) 6 to 5 1/8 in. The averages of the determinations from each series are platted on the graph (Fig. I). The vertical scale shows the percentage by volume of SO2 (as determined by the Reich method), and the horizontal scale shows the time expressed as percentage of the total sintering time. Sintering was considered to be complete when no S02 could be detected in the gases. In all cases the depth of bed was 4 ½ in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which S02 determinations were made could not be measured, but has been calculated from the S02 content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume will usually drop slightly toward the middle of the period and increase toward the end. However, this assumption is a reasonable approximation. Several interesting features are brought out by these data. In general, the published data on S02 concentration in sintering under ordinary conditions show a high S02 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SO2 in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum S02 concentration is obtained 2 ½ min. after

Jan 1, 1942

Jan 1, 1955

By D. C. McLean

This report summarizes the work that has been done during the past several years in adapting resins for use as auxiliaries in mine roof support. The resins were applied in two ways: 1) by injection into the strata, and 2) as a bonding agent for roof bolts and reinforcing bar. The Explosives and Mining Chemicals Department of the American Cyanamid Co. has worked during this period in cooperation with the Roof Control Research Group of the U.S. Bureau of Mines, the Pattin Manufacturing Co., the J. H. Fletcher Co., the Homestake Mining Co., the U.S. Steel Corp., the National Mines Corp. and the Pocahontas Land Corp. in an effort to create resin formulations and methods for applying them as a practical and sate type of roof support for mining areas particularly where conventional support is inadequate, yet expensive. This, work has involved much pioneering in a field where theory, speculation, and pure mythology predominates, and little basic engineering data is available. It is strange butt true that, despite the importance of roof control both from an operational and safely standpoint, there is scarcely a mining' company in this country that has an engineer, or anyone, assigned to the study of roof support problem, except temporarily--after a bad roof fall. The responsibility for improving roof control methods seems to have been placed entirely upon the shoulder, of the USBM, various State departments of mines, and individual roof bolt manufacturing; companies. It was in cooperation with the USBM that Cyanamid first developed resins for mining use.

Jan 1, 1964

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sand-blasting agent, as a premium grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. It is produced by E. I. du Pont de Nemours & Co. as a coproduct in titanium mineral production in Florida where it was first recovered on a commercial scale in June 1952 from the Pleistocene sand deposit known as Trail Ridge. In the Trail Ridge deposit it comprises about one-fifth of the heavy minerals, the principal other heavy mineral constituents being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and the other silicate nonconductive heavy minerals are separated from the conductive titanium minerals on high-tension separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total processing, 200 tons of raw sand yield 7 tons of heavy mineral concentrate from which about one ton of staurolite is recovered. This process yields staurolite concentrates of the characteristics given in Table 1. These concentrates are sold as three products with the size distribution of subrounded particles shown in Table 2. All three grades are used in sand-blasting for cleaning metal, for paint removal, and for cleaning buildings. Staurolite compares favorably with lower unit cost abrasives, such as boiler slags and mineral aggregates, in applications where the abrasive is used only one time and is not recovered. Because it is hard, fine, clean, and dense it can reduce blasting time, with less material reportedly being required [ ]

Jan 1, 1983

By J. J. Sense

10.2-1. Equipment Scheduling. In any earth-moving operation, more profit may be earned or lost by equipment scheduling than by any other single facet of the project. Many now-defunct earth movers would have survived the cost-profit squeeze had they followed an efficient, cost saving, equipment scheduling program. The ideal program would have every item of the equipment fleet working all of the time. In practice for many obvious reasons, principally mechanical conditions, operating conditions, and human nature-this ideal situation is not possible. The cost-conscious organization strives to keep as many pieces of equipment of the fleet working efficiently as much of the work day as possible. Operating efficiency requires the minimum equipment to move the predetermined tonnages in the prescribed period of time. In the case of a shovel-truck operation this would mean the scheduling of the minimum shovel and truck shifts to excavate and transport the necessary tonnage to the processing plant or waste dump. To accomplish this goal, the operator must work from the predetermined production established by the requirements of the plant, stripping ratio, mine plan, etc. This production schedule may be in terms of tons or yards per year, per month, or per hour, but must eventually be translated into tons or yards per ma- chine per unit of time. In this regard, the reader is referred to Sections 8.0, Excavation and Loading, and 9.0, Haulage and Transportation. The trend to larger and faster, and as a result more costly, equipment requires that the operator consider every possibility to keep the equipment operating around the clock, seven days per week. In some areas seven day operation may not be feasible economically, because of premium pay for Sunday work. Mine labor agreements are generally written without premium pay penalties for weekend work, and such scheduling is possible and most often desirable.

Jan 1, 1968