Search Documents

Jan 1, 1968

ANYONE who wishes to make the patterns for statues in order to cast them later in bronze, even though he himself is the artificer who made them, must take many things into consideration: first, whether they are large or small, and whether they are wholly round or only in part; then of what material they are made, for the way that can be followed if they are of wax cannot be used if they are of clay, wood, marble, or even of plaster; likewise he must consider whether or not it has irons inside to support it. There is also a great difference in facility if the support is placed more in. one way than in another. Great consideration should be given to whether it is to be made hollow or solid. If you have not been the workman yourself, you must at least have been an active helper in this and in every other part in order to be able to observe everything without a fault. For if they are large it is necessary to make their moulds in pieces, with marks and measurements so that you can replace them-at will exactly in the same order and in the same places after they have been taken out. But if you are the artificer [as well as sculptor] the process is made easier. Taking the ordinary way and, over an iron, make out of well beaten moulding clay, compounded with cloth clippings a core exactly as the statue is to be or however large you wish the hollow to be. Dry and bake it. On top of this work the wax, thickening it all over as much as you wish the bronze to be and finish it completely, remembering to arrange that the base may come out solid with bronze so as to support the whole work. Then take some rods of hammered bronze one dito thick and one palmo long. Pass these throughs the thickness of the wax and fasten them in several places in the core of clay that you made. [81] Do it so that they, project out of the wax a good three or four dita. These are, put in so that when the wax is removed the core is held in the middle of the mould that forms the outer part, and this outer part is held by the inner part, namely the core, so that the mould may not move in any part from its place even when it is handled. This done, take some of that clay made with well-prepared cloth clippings as I taught you, and mix with it if you wish some wash ashes or

Jan 1, 1942

By John R. Green

ROTARY kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary according to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. MEASUREMENTS OF KILN TEMPERATURE The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration.. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records or automatic control are desired, while optical pyrometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. I shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected from puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly o° to over 200°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without. effect of the flame temperature. There should be some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors Influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and com¬ments on the possibility of measurement and control. Of greater number and of varied influ¬ence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1941

By J. Moore Samuel

THE prospective change in ore receipts at the Copper Queen reduction works necessitated a careful study of conditions to determine the most economical method of smelting. The first step, calculating the known, probable, and possible results, showed the economy of a unimetallurgical flow sheet f which the three pyrometallurgical stages would be roasting, reverberatory smelting, and converting. The past and future ore receipts (not including converter flux) are as follows: AVERAGE MONTHLY FUTURE MONTHLY RECEIPTS, 1918 RECEIPTS TONS PER PER CENT. OF TONS PER PER CENT. OF MONTH TOTAL RECEIPTS MONTH TOTAL RECEIPTS Ore 84,553 82.3 43,000 44.0 Gravity concentrates 16,375 15.9 25,500 26.0 Flotation concentrates 1,883 1.8 29,400 30.0 Total 102,811 100.0 97,900 100.0 Of the 102,811 tons per month received in 1918, only 28,945, or 28 per cent., was treated in the roasters and an average f 14.1 roasters out of 20 were in operation; the remaining ore was treated in the blast furnaces. The change to "all reverb." practice, therefore, called for considerable additional roaster capacity, which could be obtained either by building additional units, or by remodelling the present units so as to give increased unit capacity. In view of the progress in roasting practice since the construction of the Copper Queen roaster plant and the heavy investment in that roaster plant, the second plan seemed to be the more desirable. The Copper Queen roaster plant consisted of twenty six-hearth, McDougall roasters, 18 ft. in diameter, equipped with cast-iron arms that originally were water cooled but now are air cooled. They have no top dry hearth and the feed is discharged through the top arch, near its periphery, by plunger feeders from two bins at opposite sides of the roaster.

Jan 7, 1921

By H. Foster Bain

THIS subject is one that has attracted my attention for a good many years. All of us have had occa-sion to think of the waste that comes from the poor organization of our methods of finding mines and of looking after prospects. Probably all of us, in, examination work, have made a long and difficult journey to see some prospect, in a far country, or often in the mountains, have found the prospect one that never could be developed, and have learned for the first time that it had been previously examined by from two to six of our professional associates, who, each in turn, condemned the property as worthless. I know properties, as all of you do, that have been repeatedly examined by first-class engineers. Perhaps it would not be safe or wise to have an invariable rule that, each prospect should be entitled to only one examination by one engineer; and yet, it seems to me that somewhere there is a middle ground to take; it is hardly necessary that each little prospect should be examined so many times that the walls get greasy from the climbing of mining engineers, or the stopes get filled up with cigarette stumps. 'This mining engineering profession ought to have brains enough to find some way of making this unnecessary, and of making the benefit of an examination, in some cases at least, and in a much larger number of cases than at present, avail-able to the industry as a whole. If we would save the amount of money that is spent unnecessarily on reexamination of properties, and let that money flow into the actual development of )properties, I believe that, in the long run, we would be better off. Just how to do that is another problem. In 1916, while in London, Edgar Rickard and I attempted to do something of that kind. We started to organize a plan whereby mining engineers might, with the consent of their class, turn over to a central organization their reports on properties they had examined, whereby men who had occasion to look up these same properties might, on payment of a fee (which should go back to the original client, if you desire, or might be devoted to some other purpose for the benefit of the industry), have access to these earlier reports. We found, in the short time we considered this matter, that a good many British engineers, and a good many of the companies, were willing to consider this. In other words, they were willing to pool their information, as a matter of practical experience. We all know the enormous value of pooling information. I think it is a problem that may well be considered from the point of view of the industry as a whole, which the Society might attempt' to work out on a businesslike basis. Assuming, however, that it is possible to work out a plan whereby we get the minimum number of examina-tions that are necessary and we make some saving in money, we reach another stage-the problem of the examination itself.

Jan 3, 1922

"No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world's supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of ""boom"" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.A technical discussion of the ore occurrence and mining operations in the camp will be the subject of a paper to be read before this meeting of the Institute. The mission of this article is to supply a ""Baedeker"" where Baedeker is lacking.The town of Park City is a typical, up-to-date, western mining camp which owes its existence as a town of 4,500 inhabitants solely to the mining industry. The camp is located 7,000 feet above sea level, thirty-two miles east of Salt Lake City. It is situated on the Victory Highway seven miles from its junction with the Lincoln Highway and has the benefit of excellent automobile communication with the metropolis of the state. Both the Denver and Rio Grande and the Union Pacific Railroads give daily train service to the camp and effectively solve the transportation problems of the mining companies."

Jan 1, 1925

By John A. THOMPSON, Pazcl D. Torrey, Frank Breayster

DISCOVERY of natural gas in the Dundee field of New York in February, 1930, and the subsequent discovery in Tioga in September of that year, focused the attention of the natural-gas industry on the enormous possibilities of production and distribution in - the most populous area of the United States-New York and New England. Prior to 1926 the natural-gas industry in New York State had settled into a definite and limited policy, with the distributing companies controlling the output from its discovery to the ultimate consumer. Production amounted to between G and 7 thousand mil- lion cubic feet a year, with another 10,000 million feet imported from Pennsylvania for distribution in New York State. This gas was primarily from the Medina sand stone in. the western part of the state.

Jan 1, 1932

Low Zinc Prices Close Alcoa Mine Alcoa Mining Co., announced that it will suspend operations at its Hutson mine, near Salem, Ky., because of low zinc prices, January 15. The Aluminum Co. of America subsidiary announced that the low market has made zinc mining un- profitable. About 70 men were employed at the mine, with a production of about 5000 tons of zinc annually. Alcoa said the shutdown would not affect other company operations, with most of the men at Hutson absorbed in the mining firm's fluorspar operations in the same area.

Jan 2, 1953

By M. L. Lissberger

entirely suitable for certain uses and even possess advantages over present solders at high temperatures, but they are certainly not suitable for all uses. However, it is conceivable that their use in many places will effect a material conservation of tin. It will probably be wiser to use cadmium in solders where good results have been obtained than in brass where this element will be a source of possible trouble. F. F. Colcord,* New York, N. Y.-—The cadmium-lead solder has a higher conductivity than the lead-tin alloy, which ought to make it advantageous in the manufacture of electrical machinery. In the case of solder for tin-can work, one of the high officials of the American Can Co. said that he fully intended to .give it a good trial, and I do not believe they are going to reach hasty conclusions and run the risk of poisoning the public. Solder, Its Use and Abuse Milton L. LissbeRgeR,† New York, N. Y.—Solder is a mechanical mixture of tin and lead, a fact which is susceptible of very simple demonstration. A bar of solder of a grade even as low as 30 per cent. tin and 70 per cent. lead, passed through a buffing machine, will show a surface practically identical with that of a bar of second-quality or reclaimed tin. The buffings, on chemical analysis, will prove to be almost pure lead. According to the best practice, solder is made in the following manner. Virgin pig lead is first melted, and when it is thoroughly liquefied, virgin pig tin is added, together with a small amount of flux; the latter is for the purpose of bringing to the surface the so-called "liver," consisting of impurities that may have remained in either the lead or the tin as a result of incomplete refining. The combined material, when completely liquid, is thoroughly stirred for some hours, and is then cast into small pigs. Just before casting, and continuously during this operation, the molten metal yields dross, consisting largely of the oxides of lead and tin; this should be carefully skimmed off. After the pigs have cooled, they are taken to a smaller kettle, re-melted, and cast into the desired shape for use; or if wires, ribbons, etc., are to be made, the solder is cast into slugs suitable for extrusion and rolling. During this second operation, the skimming of dross should be even more carefully done than at first. Hand mixing has proved to be the only reliable method for the production of the best quality of solder, irrespective of its percentages of lead and tin. The best quality of solder is not necessarily that which contains the highest percentage of tin, but rather is that composition which performs best on the required piece of work. In order to produce

Jan 1, 1919

By Charles A. Ashburner

The manufacturing and domestic consumers of anthracite are beginning to realize the fact more fully, that the coal purchased for any one year does not seem to burn so freely, does not fire with so little trouble, and does not last so long as that purchased during other years, or vice versa. Where coals of different sizes, or from different districts, are offered to the trade by the same or competing salesmen, the question suggests itself, which shall we buy ? Among housekeepers, who are the most numerous class of consumers, though on the smallest scale, distinction is seldom recognized among these anthracites. By other consumers the coals are grouped into those which, when burned, will produce either a white or a red ash, special qualities being arbitrarily attached to each. Others, again, know only of three varieties : (1) Those from the WYoming and LacKawanna fields, or the coals shipped from the northernmost basins over the railroads running through northeastern Pennsylvania direct to New York—notably, the Delaware. Lackawanna and Western, Delaware and Hudson, and Erie railways; (2) those shipped by the Lehigh Valley Railroad and the Lehigh and Susqaehanna division of the Philadelphia and Reading Railroad down the Lehigh Valley ; and (3) those shipped over the main line of the Philadelphia and Reading Railroad down the Schuylkill Valley. In special localities, where a favorite coal is largely used, the consumer will speak of one class, composed of his favorite coal, which possibly comes from two or three collieries, with a total aggregate annual production of less than a million tons; and of a second class, composed of the coals from all the other collieries in the anthracite

Jan 1, 1886

By G. Gabra

The kinetics of acidified thiourea leaching of pyrite concentrate was investigated at temperature ranging form 20 °C to a 60 °C. The effect of various parameters on the dissolution rates are discussed. The gold extraction was found to be zero and first orders with respect to Fe (111) and thiourea concentration, respectively. The order of the reaction with respect to sulfuric acid was found to be zero. The activation energy was determined from the Arrhenius plot as 2,039 kcal mole -1 (for a freshly prepared acidic solution containing Fe (111) as the oxidant and at 800 rpm stirring speed. This relatively low activation energy value suggests that the gold extraction is controlled by a-physical phenomenon. Under optimum conditions, more than 90% of gold has been dissolved in about 30 min. and 95% in 60 min. Attempt to recover gold from thiourea solution using active carbon is also discussed.

Jan 1, 1984

By J. P. Martin, A. H. Geisler, J. H. Crede, E. Both

The investigation of a 50 pct Co alloy was undertaken to determine whether there was any direct correlation between the structure and properties of Co-Fe alloys which were given various magnetic heat treatments. The magnetic anisotropy and texture of the 0.002-in. cold-reduced 98 pct material tend to decrease and change in nature with increasing temperature of the recrystallization anneal. Annealing samples in a magnetic field had little effect on either the magnetic properties or texture. However, cooling them in a magnetic field greatly improved their magnetic properties. THE beneficial influence of a magnetic field applied during the heat treatment of certain soft magnetic materials has been known for a long time. Early work showed that the presence of a magnetic field of a few oersteds during the heat treatment of Fe-Ni alloys will cause a large increase in maximum permeability. A pronounced increase in the residual induction which is produced by the magnetic anneal causes the hysteresis loop to approach the shape of a rectangle. Such results are beneficial since the desired properties are high permeability, high induction at maximum permeability, high residual induction, and low coercive force. More recently Libsch and coworkers1 studied the effect of magnetic annealing on the hysteresis properties of a series of Co-Fe alloys prepared from powders. They observed good response for the 35 and 50 pct Co alloys but little response for the 42 pct Co alloy. They pointed out that this was somewhat surprising since the 42 pct alloy has a high linear magnetostriction and zero crystal anisotropy and similar conditions in Fe-Ni alloys give excellent response to magnetic annealing. They found optimum properties to be at the 50 pct composition with residual induction, Br = 19,000 gauss and coercive force, Hc = 0.68 oersteds after the magnetic anneal. Before the magnetic anneal these values were B, = 12,600 gauss and Hc = 1.15 oersteds. The optimum treatment consisted of cooling from above the y-a transformation temperature to 900°C in a field of 20 oersteds, holding 11/2 hr at 900°C, then cooling at a rate of 20° to 25°C per min in the field to below 230°C. Cooling rate mainly affected coercive force with the value decreasing from 1.09 to 0.88 oersteds as the rate was increased from 3° to 48°C per min. Cooling from 1020" to 900°C in a field followed by further cooling to 230°C without the field gave properties decidedly inferior to those for samples annealed with the field applied throughout the cooling. They concluded that to get the best properties the samples must be cooled in a field to a threshold temperature above which the alloy is plastic enough to be affected by magnetostriction. In this respect the holding temperature must be high enough so that the alloy exhibits good plasticity to permit the optimum orienting of magnetic domains by relaxation of magnetostriction. In contrast, the holding time was of less significance for there was little improvement when the time exceeded 1/2 hr. The improvement in properties effected by magnetic annealing has usually been attributed to the establishment of a domain texture caused by the "freezing in" of magnetic strains. On the other hand, Smoluchowski and Turner2,3 apparently found that a magnetic field applied during recrystallization could alter the crystal texture. If this effect is real, improved properties would also be expected when

Jan 1, 1954

FROM newspaper reports circulated in Indonesia, it seems quite obvious that many people, even the left-wingers, have serious doubts concerning the wisdom of the Indonesian Government in nationalizing the Bangka Island tin mines, formerly operated by the Dutch Billiton Co. Chief source of American dollars for Indonesia has been the 34,000 ton tin production of its mines. Right now, both left and right are concerned with whether the Government will be able to maintain and increase current production. The right wing Moslem party newspaper, Mimbar Indonesia, stated: "It will no longer be possible any more for radical labor leaders to find foreign scapegoats and tell the workers they are working only for foreign interests and foreign managements. It is up to labor now to increase its labors for the national good. It will be a new experience, and the problem is whether we are capable enough to manage these important mines."

Jan 4, 1953

By Theodore B. Comstock

The existing topographical features of the United States present many points of interest to the student of dynamical geology, but there is, perhaps, no subject which offers a more promising field for investigation than the relations between the geological structure and the mineralogical characteristics of the principal mining districts. There are seven prominent culminating points in the relief of North America, each one of which can be used as a type of the physical features of all the others. Again, if we divide these seven elevated districts into two sets, we shall discover a still more striking parallelism between the individual members of each group. But the most remarkable revelation is the fact that each one of these points is more or less closely the centre of an area of economically important mineral resources. It is interesting to note in this connection that six of these mineral tracts lie mainly within the borders of the United States, three of them being almost wholly in our territory. For

Jan 1, 1883

By W. M. Pierce

THE present work has been done in an endeavor to correlate and complete the data on the constitution of alloys of zinc with other common, metals, dealing exclusively, however, with the zinc-rich alloys in which the zinc content is between 90 and 100 per cent. This investigation has included the systems lead-zinc, cadmium-zinc, iron-zinc, copper-zinc, aluminum-zinc, nickel-zinc, manganese-zinc, cobalt-zinc, tin-zinc, and magnesium-zinc. The important ternary system zinc-lead-cadmium and the zinc corners of other ternary systems have been investigated in connection with this work but will not be dealt with here. Zinc does not form a single homogenous zinc-rich solid solution over any considerable range of concentration with any of the metals mentioned. A limited range of solid solubility is said,; by previous investigators, to occur in several cases and certain effects on the properties of zinc are attributed (with varying degrees of consistency among different writers) to the presence of certain other metals dissolved in zinc. The increasing use of rolled zinc and the possibilities offered by zinc as a casting alloy in certain fields have it made essential to determine precisely these equilibrium relationships. In carrying out this .investigation reliance was placed chiefly on two methods, conductivity measurements and microscopic analysis. The first method proved valuable in determining the existence and extent of solid solubility. The second method stands alone as a means of determining structural characteristics and supplements the first method in the measurement of solid solubility. The scleroscopic hardness of all conductivity specimens was measured partly for its value from the point of view of mechanical properties and partly; as a check on the conductivity curves in indicating the limits of solid solubility. No hardness curves are included in this paper, for in no case were they important in arriving at the constitution of any system.

Jan 2, 1922

By D. A. Belforti, M. P. Lepie

Spectroscopically pure copper was melted on sapphire plaques in a zydrogen atmosphere. The surface tension of the liquid metal was determined using the sessile drop technique. Measurements were made by direct observation with the aid of a specially const,mcted telescope. The value obtained, 1268 dynes per cm, is compared to that found in the literature. THERE is at this time considerable interest in the use of ceramics for vacuum tubes. The crystalline material is superior to the more conventional glass in mechanical strength, chemical inertness, dielectric properties, ability to withstand high temperatures, and so forth. However, ceramics are much more difficult to seal hermetically with metals than are the glasses. For this reason an investigation was undertaken to determine the wetting and adhesion of metals to ceramics. The sessile drop technique offers a convenient means at elevated temperatures for measuring liquid surface tension, wetting angle, density, spread- ing coefficient, and work of adhesion. Thus, from the contour of a drop of liquid at rest on a solid surface one can obtain a quantitative evaluation of the degree to which the two substances will bond. To this end a special apparatus was constructed so that various molten metals could be observed. Standardization of the apparatus was done initially by measuring the surface tension of copper since this is well documented in the metallurgy literature. Although there are many methods available for the measurement of surface energy,'+ the sessile drop technique has been used most extensively for molten metals and ceramics.5"' Fig. 1 illustrates the dimensions to be measured. From these values, the surface tension of the liquid can be obtained using the Bashforth and bdams' equation and tables.

Jan 1, 1963

By R. G. Burdick, W. R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abondoned coal mines also imposes potential hazards in current underground mining operations, since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive manmade tunnels in previous work has led to the development of a surface-operated automatic earth resistivity survey system and associated computer data reduction process for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to-diameter ratios greater than 10 to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting abandoned coal mine workings. The hardware and software aspects of third new system are described together with applications of the method for surveying and mapping abandoned coal mine workings. Field tests are presented to illustrate the detection of both air-filled and water-filled mine workings.

Jan 1, 1984

By William P. Blake

THE phenomena of concentric arrangement of minerals in rock-masses, generally known as "orbicular structure," have of late received much attention from investigators. Lawson, of the University of California, has described the orbicular gabbro at Dehesa, San Diego county, Cal. Kessler and Hamilton, of Stanford University, working independently upon the same subject, published their descriptions,2 giving also a list of many other localities in Europe and America where orbicular rocks are found, adding copious references to the literature of the subject. The orbicular diorite of the type locality in Corsica., familiar to mineralogists and petrologists under the name "Napoleonite," was described by Vogelslang in 1862.3 Chrustschoff, of St. Petersburg, has also given much atten¬tion to the subject, and is the author of a classification of the various known forms of orbicular structure.4 No complete and satisfactory explanation of the origin of or¬bicular aggregations in rocks has yet been offered. The patent fact is generally recognized that the constituent minerals have crystallized from a more or less molten or plastic magma, but why these minerals should be arranged in concentric spheres or crusts has not been clearly shown. Vogelslang, for example,

Jul 1, 1905

By E. R. Parker, D. L. Martin

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944