Search Documents

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 'poises' times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 'poises' times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946

By Arthur Phillips

THE normal method of preparing metallic alloys for commercial use involves the preparation of a melt containing the given components in the chosen proportions and allowing the homogeneous liquid mass to solidify in a mold of the desired form. The solidification is frequently accompanied by a segregation of the alloying elements in different parts of the casting. When the segregation is occasioned primarily by marked differences in density of the solid and liquid phases, it is termed "gravity" segregation. When the segregation conforms to a. selective freezing in harmony with the teachings of the equilibrium diagram of the alloy system-i.e., the lower melting phases are concentrated in the regions of the casting last to freeze-it is often referred to as " normal" segrega-tion. However, in many cases the lower-melting part of the system is concentrated in the parts of the casting first to freeze and the result in this case is termed "inverse" segregation. To complete the. terminology of the subject, normal segregation in a single phase is usually called "coring" and the word will be used in that sense in this paper. Inverse segregation, particularly when the liquid phase is exuded or sweated out on the surface of the casting, is sometimes called "location." Unfortunately, some ambiguity has arisen from the use of this term and it is perhaps advisable to confine its use to the dictionary definition; namely, "The separation of two phases by heat sufficient to melt one but not the other." The gravity and normal types of segregation are both well understood and to some extent are controllable by taking advantage of the most favorable cooling rate for a given casting condition. Inverse segregation has received considerable attention from several investigators- but none of the theories offered seem to account in a convincing way for the many examples of this type. The observations made in the present work on segregation in single crystals, and in some other castings, tend to support one theory of the mechanism of inverse segregation and definitely to

Jan 1, 1937

By K. S. Seljesater

SINCE the development of dispersion-hardenable lead-antimony alloys1 in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. EXPERIMENTAL In order to-study the effect ,of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per FIG. 1..-CHANGE OF MICRO-BRINELL HARDNESS WITH TIME OF 1 PER CENT. LEAD-ANTIMONY ALLOY. cent. lead). The alloys were cast into bars 1 ½ in. wide by ¾ in. thick and cold-rolled to about 1/8 in. thickness. Three samples of each composition were annealed 1 hr. at 225° C. and quenched in water. One set was aged at room temperature, one at 50° C., and the third at 100° C., the

Jan 1, 1929

Preheating Feature of Leyner Oil Furnace for Heating Drill Steel The No. 3 Leyner oil-burning furnace, used for heating drill steel, is now made with a preheating chamber. By this addition it is claimed that the heating capacity and, effeciency of the furnace are increased about 50 per cent. This preheater is a section which fits between the body and cover of the furnace of the old design. It may be attached to an old furnace by simply changing a few bolts. Referring to the illustration, it will be seen that the lower chamber is used for the final heating and the upper one for preheating. The type of burner now furnished with this furnace is suitable for either high- or low-pressure air. It hats merely to be throttled for high pressures and when this is done, it, is as efficient as burners designed especially for high pressures and eliminates the noise common to such burners. This furnace burns petroleum or any of its oils, such a, gasoline, kerosene, distillate, etc. Oil heating has many advantages. The steel cannot be injured by absorbing injurious elements such as sulphur, phosphorus or other impurities which :ire present in nearly all coals, nor from unequal heating since the flame imparts a uniform temperature; further, o lie steel is in full view of the operator at all times.

Jan 3, 1916

By Kennedy, Joseph E.

MANY things must be considered in coming to a decision as to what type of crushing and grinding equipment is to be used for preparing run-of-mine ore for concentration, amalgamation, flotation, or cyanidation. This paper is intended in no sense as a thorough discussion of these various factors, but rather contains a few observations based on a wide experience in the manufacture and application of milling machinery. One important governing factor is the tonnage to be dealt with. In large plants treating several thousands of tons in eight hours, a large jaw or gyratory crusher of substantial construction is standard equipment for reducing ore to 8 or 10 in. or finer. In open-pit work, using power shovels with 4- or 5-yd. dippers, a jaw crusher should have a receiving opening of 48 by 60 in., or 60 by 84 in., so that dynamite or hand sledging will not be required for breaking to a finer size before primary crushing. The coarsely broken ore is then conveyed by a belt to vibrating screens, the oversize from which is again conveyed by belts to secondary crushers having openings of 12 or 14 in., the product from which is conveyed to storage. From storage, the material goes to a finishing gyratory for reduction to 1/4 in. or finer.

Jan 1, 1936

By G. C. Mudd, E. J. Myers

Within the last 15 years David Brown Gear Industries has manufactured approximately 200 large mill gears over 6m diam., 58 of them over 9 m and up to 12 m diam. The experience has not been without problems, due to a lack of clear understanding of the loads and stresses imposed on large gear wheels. American Gear Manufacturers Association (AGMA) practices suggest that a service factor be used for mill gears. But what is meant by "service factor"? The layman might be forgiven for believing that the term is synonymous with "safety factor," but this is certainly not true. The service factor is an aggregate of the following in some proportion: -An application factor, i.e., an allowance for the fact that systems do not run smoothly with uniform torque. -An ignorance factor covering the imperfections in the basic gear calculation. -Possibly a safety factor. In the following sections some of the ways in which the limits of applicability can be overstepped are discussed.

Jan 1, 1983

By Arthur C. Spencer

IN extension of a suggestion already made to account for certain features observed in the Juneau gold-belt in southeastern Alaska,' it is the object of the present paper to indicate in detail certain conditions in which deformation of rocks under their own weight might lead to the production of fractures in which veins could be deposited. A direct, uniformly-distributed pressure of sufficient intensity applied to an elastic brittle mass offering strong resistance to deformation produces rupture. In a material of ideal properties the surfaces of rupture under such pressure would be shearing planes inclined at 45° to the line of force, unless there be preliminary deformation, in which case this angle would be greater than 45°. This general conclusion, resting upon ana¬lytical mechanics, is completely supported by the results obtained by Daubrée in experiments upon the deformation of wax and resin prisms under compression. Let us then first con¬sider one of Daubrée's diagrams. In the case illustrated in Fig. 1, four sets of fractures in two appproximately right-angled pairs (that is to say, in conjugate sets) were produced by end-wise compression of the square cross-sectioned prisms. These fractures cut the axis of compression at approximately equal angles, not varying greatly from 45°. The location of the four sets of fractures is obviously determined by the shape of the prism, since the material in each corner acts in a way as a buttress, permitting the bulging to take place most readily on the sides. By limiting the directions in which bulging may take place, results of a more simple nature could be obtained. Take, for instance, a square prism and place it between two fixed and

Nov 1, 1905

By Anthony G. Reid

INTRODUCTION At the time of the death of Mao Tse-tung in 1976, China was a major oil producing country with a daily oil flow in the order of 1.735 million barrels. This position had been achieved with minimal assistance from the outside world. Further, only some fifteen years had elapsed since the country's daily oil production capacity had hovered at the barely significant level of one hundred thousand barrels. Why then did the new leaders of China, after this very creditable record of success, suddenly change the direction of the country's drive for future hydrocarbon production? First, by switching much of the emphasis of exploration from onshore to the offshore continental shelf basins, and further by apparently abandoning the philosophy of self reliance calling upon the world's oil industry to share in the task of locating and developing these potential offshore energy reserves. The answer is probably only partly understood by those of us outside China, However, a number of factors exerting an important influence on this decision can be identified. THE MOVE OFFSHORE The new leadership was anxious to rapidly move China into her rightful place amongst the powerful and technologically advanced nations of the world. Modernization became the slogan, specifically modernization on four fronts, agriculture, industry, technology and military with the goal to "catch the west by the year 2000". But how to generate the capital to finance this massive modernization program? The rapid escalation of the price of crude oil following the 1973 Oil Embargo and the continuing apparently insatiable world demand for this now extremely precious primary resource was very clear to all. China, as a major producer, could export crude to help finance the ambitious development programs of the government. To do this, however, would require a very significant in¬crease in present production capacity, as the domestic demand even for China with her relatively low per capita energy consumption, is essentially equal to the current production. Trying to rapidly move the new regime's programs into actions, one can only assume that the planners looked at the success of the petroleum industry over the preceding fifteen years and quickly concluded that this well established curve could be maintained and indeed steepened with an increase in effort. The rapid discovery of a few more Daqing's (China's premier oil field, producing one million barrels a day) would have the country's ambitious modernization goals within reach. Petroleum would At the time of the death of Mao Tse-tung in 1976, China was a major oil producing country with a daily oil flow in the order of 1.735 million barrels. This position had been achieved with minimal assistance from the outside world. Further, only some fifteen years had elapsed since the country's daily oil production capacity had hovered at the barely significant level of one hundred thousand barrels. Why then did the new leaders of China, after this very creditable record of success, suddenly change the direction of the country's drive for future hydrocarbon production? First, by switching much of the emphasis of exploration from onshore to the offshore continental shelf basins, and further by apparently abandoning the philosophy of self reliance calling upon the world's oil industry to share in the task of locating and developing these potential offshore energy reserves. The answer is probably only partly understood by those of us outside China, However, a number of factors exerting an important influence on this decision can be identified. THE MOVE OFFSHORE The new leadership was anxious to rapidly move China into her rightful place amongst the powerful and technologically advanced nations of the world. Modernization became the slogan, specifically modernization on four fronts, agriculture, industry, technology and military with the goal to "catch the west by the year 2000", But how to generate the capital to finance this massive modernization program? The rapid escalation of the price of crude oil following the 1973 Oil Embargo and the continuing apparently insatiable world demand for this now extremely precious primary resource was very clear to all. China, as a major producer, could export crude to help finance the ambitious development programs of the government. To do this, however, would require a very significant increase in present production capacity, as the domestic demand even for China with her relatively low per capita energy consumption, is essentially equal to the current production. Trying to rapidly move the new regime's programs into actions, one can only assume that the planners looked at the success of the petroleum industry over the preceding fifteen years and quickly concluded that this well established curve could be maintained and indeed steepened with an increase in effort. The rapid discovery of a few more Daqing's (China's premier oil field, producing one million barrels a day) would have the country's ambitious modernization goals within reach. Petroleum would be the principal bridge to the bright future. The next decision involved the question of where to look for these vast new reserves. Chinese exploration teams had already looked at most of the onshore sedimentary basins and, while they were the first to admit that there was much yet to do, it was fairly clear to them that the potential for large new accumulations was confined to two areas: the little explored, remote, inhospitable regions of western China, principally Xinkiang Province and the equally unexplored offshore basins of the continental shelf and slope. In both cases China faced a very serious problem. The inhospitable environments were severely straining her petroleum industry's current technological ability to cope, particularly as the government needed rapid results. Thus the pragmatic and, to the foreign oil industry, unexpected decision to invite cooperation with the outside world. The reasons for the initial emphasis on the exploration of the offshore basins with the cooperation of foreign oil companies are again supposition on my part, but probably involved considerations of technical merit, ease of development and delivery to markets together with more sensitive issues such as controling the influence of foreign philosophies and values on the Chinese population by containing most foreign activity to the offshore. So within three years of the death of the great helmsman, China had developed a plan to involve foreign oil companies, both state and private, in a grand plan to rapidly increase the nations oil production. In fact, by this time, the first round of talks had been concluded and the first phase begun, and what a beginning. Some forty eight companies from thirteen countries had signed documents to participate formally in this world scale event. It was far easier to list those companies which did not participate than to list those which did. FOREIGN COMPANY INTEREST Why the rush by the world's oil industry to be involved in China? What was China offering which made everyone so anxious to join in? Again the answer is complex in detail, but principally involved a combination of factors which together caused this virtual stampede. Timing was a major element. Oil Companies, despite an ever increasing take by governments, were beginning to benefit. from the' rapid escalation of crude prices induced by OPEC and were looking for suitable areas to reinvest these funds. Producers

Jan 1, 1982

By Stanley F. French, Bruno F. Koch

Although the amount of dust that will be actually recovered in the six main dust-control systems cannot be accurately stated until the tests mentioned previously are carried out, it is estimated that the average air entering the wet collectors will contain around 5 grains of dust particles per cubic foot. This means that the six systems handling a total of about 133,000 cu.ft. of air per minute will return about 68 1/2 tons of dust to the concentrator per day and since the copper in this dust will average around 2 per cent, the total recovery is approximately 1.37 tons of copper every 24 hours. This important copper recovery is not due entirely to the dust-control system since in a plant without control only the duct that is dispersed to the atmosphere represents a loss. A conservative estimate of the recovery of copper solely due to the dust control system would be about half of the total or approximately 0.70 tons of copper per day.

Jan 1, 1942

By AIME AIME

ONE test is worth a thousand expert opinions, say the engineers of the John A. Roebling's Sons Co. of Trenton, N. J. Confronted with the job of building the cables for the new Hudson River Bridge between Fort Lee and upper Manhattan, the Roebling organization, in spite of its long and varied experience in building cables for suspension bridges of various sizes, recognized that old yardsticks would be of little value in estimating safety factors for the immense span across the Hudson.

Jan 1, 1929

By J. H. Klepinger, C. W. Goodale

I. Introduction....................567 II. Character oF the OrE................568 III. Old FluE System..................572 IV. Tests on Old FLUE System..............575 1. Aspiration Tests................. 575 2. Tests with Steel Settling Chamber........... 575 3. Test with Experimental Brick Flue........... 583 4. Testa on Blast Furnace Geses............. 591 V. Design of New FluE System.............. 597 VI. Main Dust Chamber................. 605 VII. Some DetailS of Construction ............. 609 VIII. THE Chimney.................... 616 IX. Operation of New FluE System............. 624 X. Temperatures and DraFTS............... 630 XI. Velocities and Volumes................ 632 XII. TeStS on the New FluE System............. 637 XIII. Conclusion..................... 643 I. Introduction. In the summer of 1909 the Boston & Montana reduction department of the Anaconda Copper Mining Co. completed a new flue system, at a cost of about $1,100,000, and as this includes the largest and highest chimney in the world, and some new features of flue construction, a description will be of interest. At the Spokane meeting of the Institute in September, 1909, a brief mention was made of this flue system, in discussing Mr. Brunton's presidential paper on the Progress of Metallurgy in the West, and a promise was given that when a long enough time had elapsed, so that operating results could be given, a paper would be offered. The smelting plant includes blast furnaces, MacDougall roasters, gas-fired reverberatories, and converters.

Jan 1, 1914

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The microhardness of single crystals of tungsten disilicide has been investigated by the Knoop method. The average random room-temperature hardness of the WSi, matrix was 1350 kg per sq mm. Hardness crnisotropy was noted with respect to plane and indenter orientation as determined by single-crq.stal X-rny studies. Annealing at 1600" and 1800°C decreased the average hardness to 1310 and 1230 kg per sq tnm, respectively, and produced a second phase identified by X-ray diffraction and electron-microprobe analysis to be wSio.7. Ball-impact experiwzents produced rosettes at 850°C. Optical and electron microscopy showed evidence of slip and cross slip and twinning produced by microhardness indentations. Prismatic (100), [001] slip was found and cor~elated with hardness data. THE present study was undertaken to investigate the hardness anisotropy of as-grown and annealed single crystals of tungsten disilicide. The existence of the silicide WSiz in the W-Si system has been well-established and its structure thoroughly investigated zachariasen2 found WSi, to have a tetragonal C type of structure, similar to that of MoSi, with lattice parameters a = 3.212A, Kieffer et al. studied the W-Si system and measured the density and microhardness (at a 100-g load) of both polycrystalline WSi, and WSi,.,. The values found were 9.25 g per cu cm and 1090 kg per sq mm for WSi,, and 12.21 per cu cm and 770 kg per sq mm for WSi0.7, respectively. According to Samsonov et a1.5 the microhardness of polycrystalline WSi2 is 1430 kg per sq mm (at a 120-g load). EXPERIMENTAL The WSi, single-crystal boules investigated in this paper were grown by a Verneuil-type process using an electric arc by the Linde Division of the Union Carbide Corp.6 The largest specimens were 8 mm in diameter by 16 mm long. The crystals had an average density of 9.01 g per cu cm with a tungsten • silicon content of 99.9 wt pct. The major impurities were: 87 ppm O, 41 ppm N. 54 pprn C, 500 ppm Zr, 50 ppm Na, and 50 ppm Mn. The crystals were silicon-poor, the average silicon content being 22.20 pct (stoichiometric value is 23.40 pct), and tungsten-rich, the average tungsten content being 77.70 pct (stoichiometric value is 76.60 pct). As-received single crystals were ground and analyzed by powder X-ray diffraction technique using Cu Ka radiation. Laue and layer line rotation patterns were obtained on cleaved sections of WSi, single crystals. Electron-microprobe traverses of representative crystals were done using a Phillips-AMR electron microanalyzer. Carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to the metallographic examination, the specimens were mounted in Lucite and then polished for short times on polishing wheels using 9-, 3-, and 1-p diamond-grade pastes. Finally they were fine-polished with Linde A powder for 24 hr on a Syntron vibratory polisher. The samples were etched with 4H 2 O:1HF:2HNO3, which is a medium fast-acting etchant. The combination 1HF:2HNO3:5 lactic acid is also a satisfactory etchant. Annealing runs for selected specimens were made at 1600" and 1800°C for 3 hr at 1.0 to 3.0 x 10-5 mm Hg. A Brew tantalum resistance furnace with WSi2 powder for setters was used. The WSi2 powder was the same as that used for the crystal growth. Temperatures were measured with a calibrated W, W-26 pct Re thermocouple and a microoptical pyrometer. Powder X-ray diffraction, emission spectrographic, and electron-microprobe analyses were done after the annealing runs. For microhardness measurements a Tukon Microhardness Tester Type FB with a Knoop indenter was used. Although measurements were taken at loads ranging from 25 to 1000 g, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Only indentations of cracking classes 1 and 2 were considered.' DISCUSSION OF RESULTS Powder X-ray diffraction analysis showed the as-received crystals to be single-phase WSi2. Laue and layer line rotation patterns obtained on cleaved sections of WSi2 single crystals proved them to be tetragonal WS 2 2 The results also indicated that the c axis of the crystal was oriented parallel to the boule or growth axis. Electron-microprobe traverses across the matrix of the as-grown crystals showed them to be homogeneous WSi,. Optical and electron microscopy of etched crystals, however, revealed that they contained minute amounts of the "golden" and the "blue" second phases as opposed to the "white" or WSi2 phase. These two second phases were concentrated in inclusion and etch-pit

Jan 1, 1965

By O. M. Schaus

GRATIFYING progress continues towards the elimination of the hazards confronting health and safety in and about mines. Employers and employees are diligently co-operating. One of the outstanding movements towards this end is the National Safety Competition conducted by the U. S. Bureau of Mines. William W. Adams, of the Bureau, has stated that "Through 1936 there has passed by a dozen years of this National Safety Competition, as it started in 1925 with an enrollment of 210 mines and quarries in 28 states and 68 million man-hours of employment. For 1936 it covered 328 mines and quar-

Jan 1, 1938

By L. W. Bahney

MANY methods for the determination of gold or silver, or both, in cyanide solutions have been published, which with care in manipulation, and modification in some cases, will give results that are satisfactory. It is possible to classify or group these methods as follows: 1. Evaporating the solution in a porcelain or agate-ware dish containing litharge,1 or in a "boat" made of lead foil. 2. Forming a lead sponge containing the precious metals by means of zinc shavings,2 zinc dust,3 or a piece of aluminum.4 3. Decomposing the cyanide solution with an acid and precipitating the precious metals by the use of one or a combination of some of the following: Copper sulphate,5 sodium sulphite,6 hydrogen sulphide,7 cement copper.8 4. Precipitating the silver by zinc dust held in a Hooch crucible and determination with a standard solution of sulphocyanate.9 5. Electrolysis.10 6. Colorimetry.11

Jan 2, 1915

By C. M. Nickerson

IT is apparent that repressuring of the oil measures is becoming increasingly important to the oil industry, and is a matter that warrants the best efforts of the petroleum engineer charged with applying this method of operation to a producing property. Considerable attention has. been directed to repressuring in various California oil fields, such as Dominguez and Seal Beach, which have served to sell the more progressive operator on this idea and also to keep him sold. The projects that have received most attention are in comparatively young fields where the fluid levels are high, the wells, perhaps, still flowing, where the wet gas production is of considerable volume, and where there is vital need of immediate conservation of gas, which otherwise would be blown to the air. The new State of California Gas Law, which prohibits the waste of gas, has served to interest the oil industry in -means of conserving the gas that is now being blown to the air because of lack of markets. This vitally affects the operator in the older, well-depleted oil fields of the state, because in many cases he has a limited market for gas, on account of the flush production from the more active oil fields. While the waste of gas is relatively small in these older fields, such as the Midway-Sunset area, it now attains considerable importance, since under the new State Gas Law it must be put to some beneficial use. Repressuring in the older fields of California has not received the attention of the petroleum engineers that is warranted by the present situation. This paper was prepared with the view of presenting the salient features connected with repressuring in the well-depleted oil measures of the older fields, and to show what results have already been obtained in these fields by injecting the unmarketable. gas into the sands, particularly in the Midway-Sunset field in the San Joaquin Valley of California. Other projects in the older fields of the state offer some supporting data in this connection, such as the Shields Canyon and the Brea Canyon fields.

Jan 1, 1929

By John C. Calhoun, Frank T. Bethel

The application of a method for analyzing pressure build-up curves to determine the effective permeability in the Spraberry is presented. Sixteen upper Spraberry wells of the Driver area arc analyzed and show variations in the in-place effective permeability of 2 to 183 md. Since these value- are much larger than the .5 md. or less reported for the matrix rock. a large part of the vertical fractures noted in Spraberry cores- must be considered native to the formation. The effectiveness of the well fracture treatment in connecting the well bore to the native fracture system is analyzed by comparison of the effective permeability as determined from the PI test to that obtained from a pressure build-up curve. These results show that the fracture treatment is sufficiently effective in connecting tile well bore to the native fractrure system to yield a flow capacity within about 50 per cent of that dictated by the native fracture system About two-thirds of the wells show some degree of local blockage. INTRODUCTION Fractured reservoirs have been known in the past.' However, during the past two years the Spraberry formation has directed the attention of the petroleum industry to a study of the performance of a fractured reservoir. The large variation in the number of fractures noted in Spraberry cores rile large variation in the producing ability of offset well.. the dramatic effect of well treatment on well ,productivity. the unknown quantity of oil stored in the fractures and matrix rock. and the unknown oil to be recovered were part of the initial Spraberry puzzle. In this type reservoir where the well treatment is an important factor in determining the productivity. it i- particularly desirable to determine the in-place flow capacity of the drainage area at distance* far removed from the well bore. This value. when compared to the flow capacity obtained from a PI measurement, will show the effectiveness of the well treatment (completion. fracture treatment, acidization. etc. in establishing a flow capacity in the vicinity of the well bore equal to that in the more remote region. The object of this paper i.; to show the application of a method of pressure build-up analysis for this purpose in studying the Upper Spraberry formation in the Driver area. STATEMENT OF THEORY The theoretical basis for the application of a pressure buildup curve to show the effective permeability of the rock at distances far removed from the well bore has been presented in detail in earlier publications.', in the previous development it was shown that pressure build-up behavior of all wells could be reduced to the same dimensionless build-up curve of Fig. 1. This mean.; that the bottom hole pressure of a well after hut-in will rise in such a manner that a plot of pressure against the logaritllm of time yields a straight line. The slope of this linp can be rlzed to calculate the effective permeability as expressed by the following equation: where: effective oil permeability md oil production rate prior to shnt in. STB/I) In practice the flow which occurs into the well bore after shut in and the variation in flow capacity in the immediate vicinity of the well bore usually cause the early part of the build-up curve to be unsatisfactory in the determination of permeability. In general the effect of these factors on the straight line section will become negligible after a time when the of the following equation is equal to 0.1. and the preferred section Of the curve for use in defining the slope lie-

Jan 1, 1953

MRS. SIDNEY J. JENNINGS, President, MRS. ARTHUR S.. DWIGHT, First Vice-President, MRS. KARL EILERS, Second Vice-President, MRS. H. W. HARDINGE, Third Vice-President, MRS. BRADLEY STOUGHTON, Recording Secretary, MRS. AXEL 0. IHLSENG, Corresponding Secretary, MRS. ARTHUR S. DWIGHT, Acting Treasurer. Welfare Committee MRS. C. C. BURGER, Chairman, Sub-Committees Americanization Belgian Relief MRS. LEVI HOLBROOK, Chairman, MRS. HENRY H: KNOX, Chairman, Emergency MRS. HERMAN A. PROSSER, Chairman. Since the annual meeting held in February, 1917, when the Woman's Auxiliary to the A. I. M. E., was formed, the work of organization, which of necessity must be slow, has steadily gone forward. Under the Chairmanship of Mrs. C. C. Burger of the Welfare Committee, three active sub-committees have been formed: that of Americanization; under Mrs. Levi Holbrook, who is eminently fitted for such a position, by her active and valuable work in a number of the fine patriotic societies of our country; the Belgian Relief Committee, under Mrs. Henry H. Knox, which has clone phenomenal work in the three months of its existence, and whose report is later given in detail; and the Emergency Committee under Mrs. Herman A. Prosser, which has a fund already established, and is. in close touch with Major Arthur S. Dwight, ready to act when necessity arises. The officers of the Auxiliary feel more than gratified at the response so far received, and in a later issue will print extracts from letters, if permission can be gotten from the writers, showing the interest and enthusiasm that have beer aroused by the formation of a Woman's Auxiliary. Answers have even come from far Korea "the hermit nation," from Australia, from South America, showing what a bond of sympathy and, helpfulness is in process of growth. It is our sad duty to announce the death of our Treasurer, Mrs. George D. Baryon, who, from the very inception of our plan to organize, was an inspiring and valuable co-worker. Her place will be difficult to fill. Mrs. Arthur S. Dwight is Acting Treasurer at present. The Auxiliary wishes to express its heartiest thanks to Mr. Stoughton, the genial and efficient Secretary of the A. I. M. E., for his cooperation and valuable suggestions in the difficult work of organizing. He has indeed been "a guide, philosopher and friend." SUSANNE M. IHLSENG (MRS. AXEL 0.), Corresponding Secretary.

Jan 7, 1917

Jan 1, 1969

By R. L. Templin

THE increasing use of aluminum and its alloys in commercial fields has demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure aluminum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual stools.

Jan 1, 1927