Search Documents

By K. N. Weaver

In the early 1950's the cement industry began putting a new emphasis on geology. This article points up some of the industry's raw materials problems that geologists are uniquely qualified to handle. Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War 11, however, the industry began to recognize the need for geological exploration and some of the larger companies began to build a permanent geological staff. This development has its roots in: 1) The rapid expansion of the industry. After World War II and continuing into the early 1950's the demand for cement far exceeded the production capacity. This placed a great deal of pressure on the producers to enlarge capacity at their plants and to develop new sites. 2) The closing of many cement plants due to inadequate raw materials. Producers feared lack of raw materials due to inadequate exploration and evaluation. 3) An ever increasing pressure for upgrading of the quality of portland cement, necessitated upgrading the quality of raw materials. 4) The increasingly large capital investment needed to build new cement plants required a higher degree of accuracy in reserve calculation. These reasons are more or less self explanatory and will not be elaborated on. They are outlined to illustrate the probable evolution of thought among cement management to justify the development of a geological staff. In the author's personal experience the geologist must continually readjust to changing conditions within the industry. For example, cement production capacity grew so rapidly that today production is only about 70% to 75% of rated capacity (73.8% in 1963). Therefore, whereas the geologist's function during the active expansion of capacity was primarily one of exploration, one of his major functions today is the development of existing reserves. This assumes of course that reserves at existing plants have been proven to be adequate in terms of the company's reserve policy. Through the proper development of raw materials, the geologist can markedly influence quality control, production and long range planning. Examples of several of the operations of Medusa Portland Cement Co. will illustrate how proper attention to geologic detail pays off in the above areas. Because limestone is the major raw material of port-land cement, the examples will be concerned with it. DEVELOPMENT OF GEOLOGIC DETAIL One of the prime objectives of an exploration or development project should be the establishment of the stratigraphy and structure of the deposit. The basic tool for exploration and development is still the core drill, and the geologist must gain a maximum amount of information from a minimum amount of drilling. In order to obtain this objective the following is essential: 1) Adequate detailed geologic logging of cores. The core is first logged and separated into lithologically distinct units. In order to make the lithologic breaks as meaningful as possible, representative pieces of core (not all) are etched in dilute HCI. This removes the "drill polish", brings out the structure of the rock and indicates the proportion of dolomite and argillaceous material because dolomite and argillaceous material etch in relief. In this way the lithologic breaks become clearer and one gains a general idea of the chemical makeup before analysis. This method of logging lessens the probability of including two types of stone, e.g. limestone and dolomite into the same sample for chemical analysis. 2) Representative sampling for chemical analysis. After logging, the lithologic units are sampled for chemical analysis. A representative analysis can be obtained by extracting a 1-in. sample for every foot of core. For example, a lithologic interval of 10 ft to 20 ft would yield ten 1-in. samples taken at 11 ft, 12 ft, 13 ft... and 20 ft. These samples are then crushed, pulverized and split into a sample for chemical analysis. This sampling method represents a significant saving of time over splitting the entire core. 3) Preparing the core as a record. Because of the expense of storage and the difficulty of handling large amounts of core, only representative samples of each lithologic unit are saved for reference. An

Jan 1, 1965

By J. Nutting, D. H. Kirkwood

The oxidation of lead sulfide in air between 200° and 350°C has been investigated by electron diffraction from thick sulfide films and from galena surfnces. It has been demonstrated that sulfate is the stable reaction product up to 570°C. Sulfate is HAGIHARA has investigated' single crystals of galena roasted in air by the reflection electron-diffraction technique, which owing to the very limited penetration of the beam into the crystal gives information of the nature of the surface only. He has shown that up to 280°C the first oxidation product is lead sulfate, followed by lead mono-oxysulfate (PbO . PbS04). At longer times and higher temperatures more complex patterns appeared which could not be analyzed. All of these patterns were of streaks or spots arising from crystals oriented on the galena surface, and it is probable that these crystals are lead compounds whose structures have not been determined, such as the other oxysulfates (2Pb0 • PbS04 and 4Pb0 . PbS04) or a number of oxides. Certain lead sulfide films, formed chemically, give ring patterns in transmission electron diffraction2 because they are polycrystalline, and should also give ring patterns of the products after oxidation. It was thought that a diffraction study would reveal the sequence of phases produced in the reactions at different temperatures, since X-ray powder patterns are available for many lead compounds. PREPARATION OF FILMS The films were prepared by passing H2S over a saturated solution of lead nitrate in water. Once a silvery film had formed on the solution surface, no further thickening was apparent. The films were transferred by a gauze to a bath of distilled water for washing and pieces of film were caught on small discs on which they were dried. The discs were formed initially on galena up to temperatures of 300°C, followed by oxide and oxysulfates in turn at longer times. The appearance of- these phases is believed to result from an inadequate rate of supply of sulfur to the top surface 01. the crystal. standard Siemens mounts, made of platinum alloy, and had seven 20-p apertures drilled through them. The parts of the film which had dried onto the disc surface were light blue in color, which is the interference color of a film about 600A in thickness. A strong pattern of lead sulfide was obtained in transmission electron diffraction through the apertures but slight broadening indicated a crystallite size of around 200A. Tilting a sulfide film in the beam produced arcing of the rings, increasing the intensities of the (Ill), (3111, and (222) rings and reducing (200) and (220). This arises from preferred orientation in the film, a [loo] direction of the crystallites being normal to the plane of the film. These specimens were oxidized in an oven maintained at the required temperature. The reported times include that taken to heat the film to the reaction temperature. STABLE PHASES FORMED IN OXIDATION The conditions in which various oxidation products of lead sulfide are stable have been considered by the authors in a previous paper.3 It was shown that in a normal atmosphere, taken as containing lo-' atm of SOs, lead sulfate would be stable up lo about 570°C. This was confirmed by oxidizing thin films of sulfide for several days, and the analysis of the transmission-diffraction pattern is given in Table 1. The fit with the patt$rn from X-rays is good, except for the missing 3.62A ring. Some disagreement in intensities of reflections given by X-rays and electrons is to be expected. Up to 570°C a spotty pattern of sulfate was still obtained, indicating grain growth, but above this temperature the film disintegrated. Probably this is associated with the decomposition to PbO . PbS04. It needs to be emphasized that the atmosphere

Jan 1, 1965

By W. H. Class

The embrittling effects of oxygen, ozone, nitrogen, air, and surface residues, on NaCl has been investigated. The embrittlement by ozone and oxygen was found to be associated with the formation of a NaClO3 surface compound. In these cases the initial crack that was responsible for fracture (in a bend test) always nucleated at the corners between the tension and side faces. The behavior of air was very erratic and on certain days did not produce enzbrittlement. During these periods, crystals that had become embrittled by the ozone treatment completely recovered their ductility after a short exposure to the ambient atmosphere, It was established many years ago1 that considerable ductility could be obtained in NaCl single-crystal specimens if the crystal surfaces were dissolved in water either during or immediately prior to the test. The original interpretation of this effect by Joffe attributed the enhanced ductility to the removal of surface microcracks by dissolution. Later investigations2'3 have suggested that the exclusion of air from the specimen surface is the criterion for extensive plastic flow prior to fracture. The air em-brittlement in this later work was attributed to the diffusion of gaseous atoms into the surface layers of the crystal, thereby impeding the movement of dislocations. This model satisfactorily accounts for the reembrittlement observed after further air exposure subsequent to the water dissolution treatment. However, the situation has recently become more complex by the observations in several laboratories4-t that under certain conditions air exposure does not impair the ductility of NaC1. It has also been recognized5 that improper drying operations after water dissolution can leave surface precipitates that lead to embrittlement. Cleavage defects on as-cleaved crystals can often be another source of embrittlement. In the present work the effect of the gaseous atmospheres nitrogen, argon, air, oxygen, and ozone, on the ductility of rock salt was studied extensively. The embrittlement resulting from oxygen and ozone exposures was found to be associated with the formation of a NaC1O3 surface film. It is suggested that certain atmospheres, one of which often can be ambient air, which inhibit the formation or favor the decomposition of this compound, can promote ductility. Thus one aspect of the Joffe effect is certainly related to the removal of surface compounds or complexes by water dissolution. The effect of surface precipitates that remain after drying operations and of cleavage defects were also studied. In neither of the latter cases was the embrittlement as severe as that found with a NaClO3 surface layer. PROCEDURE AND SPECIMEN PREPARATION The nature of the embrittlement produced by the agents mentioned above was studied by means of microscopy, mechanical testing, and X-ray diffraction. Specimens were cleaved from large crystals of optical quality sodium chloride obtained from the Harshaw Chemical Co., and, except for those tested in the as-cleaved condition, were given a 15- to 20-sec immersion in distilled water followed by a rinse in absolute methyl alcohol. The specimens were then blotted on a soft, absorbent paper, and dried by a few seconds exposure to a stream of warm, dry air. Such a procedure was found to give a control surface which was microscopically free of residues. (A few crystals were intentionally painted with a concentrated NaCl solution in order to investigate the effect of surface residues). All specimens were of 0.140 sq in. cross-section. Crystals prepared in the above manner were immediately placed in a gas train where they could be exposed to the desired gases for preselected periods of time. For the oxygen and nitrogen exposures, pure reagent-grade gases were employed. The ozone was provided in the form of an ozone-oxygen mixture (approximately 10 pct ozone) prepared by passing commercial grade oxygen over a strong ultraviolet light source. All gases were dried prior to their introduction into the train. Since argon was found to be completely inert in its behavior (i.e., residue-free specimens that were exposed to argon were not embrittled), it was periodically utilized to check the control specimen surfaces as well as the condition of the gas train used for aging the specimens. After exposure to the gaseous media in question, the crystals to be used for the measurement of the strain to fracture were transferred from the gas train to a protective oil bath (without further exposure to the atmosphere) where the tests were conducted in three-point bending. The apparatus was so adjusted that the load could be applied at a constant, continuous rate. Other Snecimens from the gas train were deformed

Jan 1, 1962

By Dr. O’Neil Thomas J., Donald W. Gentry

Pure gold was hidden in the quartz, they said, 'Twas proved by dreams and signs, and rods divining, By chemic tests, and spirits of the dead, In fact by everything-except by mining. " from R.E. White, "The Mining Town," Alta California, August 18,1873 Textbooks in mining engineering have traditionally covered ore reserve estimation and mine valuation in a single volume. Indeed, Examination and Valuation of Mineral Property by R. D. Parks (1957), having been the standard of the profession for over 20 years, is a classic example. However, the state of knowledge in these two fields has grown tremendously. Most mining engineering curricula now cover these topics in separate courses, and in practice, these tasks are usually performed by different individuals. Thus, this trend now suggests the need for separate, specialized publications rather than a single volume for both topics. Because of the separate development of the science of ore reserve estimation, it is important to state at the beginning what this chapter does not cover. It does not address in detail the design of sampling programs, sampling methods, or the processing of samples or sample data compilation. There are a number of suitable references available on these topics, including Peters (1978), Gy (1979), as well as the previously cited book by Parks. Furthermore, this chapter does not cover in any substantial detail either the traditional methods for using sample data to calculate ore reserves or the more recently developed geostatistical methods. The traditional methods are thoroughly covered by Popoff (1966) and more concisely by Barnes (1980). Among the more useful references for statistical applications in ore reserve estimation are Barnes (1980), David (1977), and Clark (1979). A thoughtful review of the entire science and art of ore reserve estimation is provided by King, McMahon, and Bujtor (1982). In spite of the fact that expansion of knowledge now calls for separate books on ore reserve estimation and financial evaluation, neither publication can ignore the important interrelationships between the two fields. In regard to this text, the unique and crucial role of ore reserves can not be omitted entirely; however, the field is now simply too extensive to treat here in any comprehensive manner.

Jan 1, 1984

By AIME AIME

THE following brief description of the main features of the, engineering work was prepared for the use of members of the American Society of Civil Engineers and members of the American Institute of Mining Engineers on the occasion of their visits to the tunnels at the time-of their respective. annual meetings in New York, January and February, 1905. DESCRIPTION. Those portions. of the Pennsylvania Extension into Manhattan and Long Island, lying east of the Terminal Station and west of the East River, have been designated as the " Manhattan ?Cross-town:. Tunnels." They traverse a section of the city second in importance only to the financial district, and one that includes the larger hotels, retail shops and theaters and the residences of many of the best known citizens. Section "D," consisting of twin tunnels for west-bound express and local passenger traffic, lies under Thirty-third Street from a point 400 ft. west of the west line of Sixth Avenue, eastward to the river shaft, situated in the block between Thirty-third and Thirty-fourth Streets east of First Avenue. Beginning at the east end, the tunnels are in separate excavations, leading westward from the subaqueous tubes, on a curve of large radius, gradually closing together until it is found more appropriate to drive them in a single excavation. At a point just west of Second Avenue they reach the tangent, aid from there westward lie directly under Thirty-third Street. At a point about 180 ft. west of the west line of Sixth Avenue, the center concrete-wall between the twin tunnels is omitted, and the excavation somewhat widened to make room for a third storage-track, and the tunnel continues to tile station portal in three-track section. Here reprinted through the courtesy of The United Engineering and Contracting Co. The half-tone blocks used for the illustration of this paper have been kindly supplied by the Chasmer-Winchell Press of New York, Pittsburgh and Cleveland.

Mar 1, 1908

By A. M. Gsudin, F. W. Bloecher, C. S. Chan-s, P. L. De Bruyn

M ANY elements can now be obtained in radioactive form. The radioisotopes have the same chemical properties as the corresponding inactive forms, differing from them only by their nuclear instability. This combination of properties permits radioelements to act as atomic tracers, the tracer atoms revealing themselves at the time of their decay with emission of electrons and positrons (beta radiation), helium nuclei (alpha radiation), or electromagnetic radiation (gamma radiation). The tracer technique is particularly attractive for the study of surface chemistry problems in general and flotation problems in particular because of its extreme sensitivity. A large proportion of the ionizing events, initiated by the characteristic decay emissions in a radioactive sample, can be recorded by radiation probes of suitable design and geometry. An idea of this sensitivity can be gathered from the following example: assume that 0.001 mg of pure RaD (radiolead), a beta-ray emitter, is used in a flota¬tion tracer experiment. This is 1210 X 10-1 mole; since the fraction trans¬formed per second (the so-called decay constant), is 9.92 X 10-10, the number of ionizing events per second would be (6.023 X 1023 X y,,, X 10-1) X 9.92 X 10-10 = 2.845 X 106. (The decay constant is expressed in sec-'. Its product with the half life, expressed in seconds, is the pure number, natural logarithm of 2 = 0.693. The half life is the length of time required for decay of one half of the total number of radioactive atoms of one particular type.) (See reference (1) at the end of this article.)

Jan 1, 1948

By J. E. Ryan

TRONA, Calif., is a miniature urban community of some 3500 people, located on the northwest shore of dry Searles Lake in the extreme northwest corner of San Bernardino County, approximately 186 miles north and east of Los Angeles. Since it is situated on the Mojave Desert, a typically desert climate prevails with wide variations in temperature between day and night, extreme daytime summer heat, and cool to cold winters. Rainfall averages somewhat less than 4 in. per year, and dust storms are common. The rate of evaporation, .however, is great, amounting to 6 to 9 ft of water per year. The extremely low humidity makes the summer heat of 110°F tolerable with only a mild, temporary discomfort. Nature of Deposit During the periods when Searles Basin was flooded, the waters that passed through Indian Wells Valley spread out to form a broad, shallow lake providing, in effect, a settling basin for suspended sediment. The drainage into the deeper and more isolated Searles Basin thus was clarified to a great degree before concentration began. Today, the elevation of the dry surface of Searles Lake is 1618 ft, and the salt deposit measures 5x7 miles. At the eastern and northeastern margins of the main playa zone and just at the foot of the alluvial slope of sand and coarser wash from the Slate Range mountains, a rim of crusted salts rises a few feet above the level of the flat. The deposit is a saline efflorescence composed of salts that were presumably brought up with rising ground waters to be deposited at the surface by solar evaporation. This deposit consists chiefly of trona, and it is after this Trona Reef that the town Trona was named. Strip mining operations have been conducted in the past at infrequent intervals for the recovery of crude trona salts. The main focal point of interest in Searles Lake from a commercial standpoint is the main salt body located almost centrally in the basin. The exposed portion of this porous saline deposit covers approximately 12 sq miles and averages 71 ft deep. Its interstitial voids, which constitute 50 pct of the total volume, are permeated with a brine, which is in equilibrium with the soluble salt deposits. The brine is the raw material for the operations of the American Potash and Chemical Corp. plant at Trona, shown in Fig. 1. The soluble salt deposits are of interest for their potential values in future technologic development. The brine, which is stratified according to slight differences in density, stands usually within 6 in. of the surface of this exposed, firm, salt body. The surface is usually dry and will support the weight of heavy mobile units and drilling equipment. Occasionally, however, surface waters from the higher watersheds encroach upon the main salt body during infrequent periods of precipitation on the surrounding mountains. This water dissolves surface salt, becomes a dilute brine, and has been observed to stand as high as 18 in. above the salt surface when undisturbed. Windstorms will shift the water back and forth across the lake surface. The exposed salt body is surrounded by additional submerged areas of commercial soluble salt deposits covering some 20 sq miles, hidden from view by marginal playa mud. These vary in depth up to as much as 30 ft. Thus, the outline of exposed and submerged salt deposits of commercial value is estimated to cover a total area of 32 sq miles, which is roughly circular but slightly elongated from northwest to southeast. It has been estimated that each square mile contains about 100 million tons% f alkali salts. The results of drill borings in the past 15 years have brought to light the interesting fact that the main salt body lies superimposed on an impervious mud deposit from 10 to 15 ft thick containing relatively little soluble salt. Under this deposit lies a second soluble salt body 35 ft deep. The lower salt body is interspersed with numerous insoluble mud lenses and its composition is considerably different from that of the primary, or main salt deposit. Recent drill borings have not penetrated beyond 300 ft. They have, however, revealed that underlying the lower salt body, the mud sediments carry deposited minerals of trona, nahcolite, mirabilite and much less soluble carbonates or sulphates of calcium and/ or magnesium. This structure is shown in Fig. 2. Current Lake Survey Program Several hundred holes have been drilled in the deposit. However, to carry out a thorough and carefully correlated study of the composition of the soluble salts and other minerals in the dry lake basin, a drilling program was inaugurated recently and is now nearing completion. In this survey, pattern drill holes are sunk at regular lh-mile intervals to a depth of approximately 150 ft. Drilling equipment consists of a No. 51 C. P.

Jan 1, 1952

By Alden Greninger

ALTHOUGH the crystallography of lattice transformations has been studied extensively during the past few years, these studies have been limited, with few exceptions1,2, to specimens in which the transformed lattice appears as a, segregate phase. A realization of the technical importance of the segregation mechanism, especially in the formation of martensitic structures and in age-hardening phenomena, has undoubtedly stimulated research in this direction. In the crystallographic studies of segregation, the general problem has been to relate the orientation of the parent crystal to that of the segregate crystals. The technique has been complicated by the fact that it has been necessary to deal with the presence of as many as 24 ideal segregate orientations within one parent lattice; furthermore, the segregate lattices are invariably scattered (seldom less than ±2°, often as much as 15° or 20°) about these ideal positions. It is probable that a more complete picture of phase transformations may result from a study in which complete lattice relationships between individual grains are evaluated, thereby providing an additional param-eter which, when it is necessary to work with multiple segregate-orienta-tions, cannot be evaluated. The present paper presents the results of such a study, ? wherein a peritectic reaction is made use of to produce the transformed lattices.

Jan 1, 1937

By D. Geiselman, A. G. Guy

Single cvystals were grown from high-purity magnesium containing known amounts of nitvogen in the range 0.0008 to 0.0048 wt pet. Crystals of known ovientation were tested in tension in an Instron ma chine to determine the yield strength and to obsevue wheather a yield point occurred. Slowly cooled crystals or those given a solution heat treatment did not show a yield point. However, crystals that were aged following a solution treatment showed a yield point for all of the nitrogen contents studied. It was concluded that nitrogen caused the yield point by the Cottrell mechanism. NITROGEN has been shown to produce sharp yield points in single crystals of cadmium, zinc,2'3 ß-brass,4 and iron,5,6 as well as in polycrystalline iron7 and molybdenum.8,9 Since magnesium has a structure similar to zinc and cadmium, it seemed reasonable that magnesium should also exhibit a sharp yield point provided it contained sufficient nitrogen. Bobalek and Shrader10 reported a total nitrogen content of 0.002 to 0.0065 wt pct in com- mercial magnesium alloys, an amount well in excess of that required by theory. However. magnesium differs from cadmium and zinc in that it forms a stable nitride, Mg3N2, which has a standard free energy of formation of -95,480 cal per mole at 25" c." If rather than being in solid solution, the nitrogen were predominantly combined as the nitride, it could not act to produce a yield point. This type of behavior is the basis for the elimination of strain aging and a yield point in steel by the addition of strong nitride formers such as titanium,12 columbium,13 aluminum,14 vanadium,15 and boron.16,17 Thus, there appeared to be factors both favorable and unfavorable to the production by nitrogen of a sharp yield point in magnesium, and the purpose of this investigation was to determine the actual behavior of magnesium crystals containing known amounts of nitrogen.

Jan 1, 1960

By FRANK R. VAN

I. INTRODUCTION. IN the summer of 1908, R. B. Cochran, Superintendent of the Compania Metalurgica Mexicana at Sierra Mojada, Mexico, presented to the Department of Geology and Mineralogy at Case School of Applied Science an interesting series of silver-, copper-, and lead-ores from the Veta Rica mine. These ores contained several interesting minerals which were associated in a somewhat peculiar manner, so that I was impelled to make a closer study of their occurrence. The investigation has brought out several new facts concerning the geology of the district and the geological occurrence of the ores, and therefore has seemed worthy of record. Two papers have been published previously about the region, one by Chism1 in 1887, and the other by Malcolmson2 in 1902. These articles, however, treat of the district more from the stand-point of the metallurgist and mining engineer, and not much attention is devoted to its mineralogy and economic geology. II. GEOGRAPHICAL LOCATION OF THE DISTRICT. The Sierra Mojada is situated in the extreme western part of the State of Coahuila, near the Chihuahua boundary. It is reached best via the Mexican Central railroad from El Paso, Tex., to Escalon, Chihuahua, a distance of 494 miles. From this point, a branch line, the Mexican Northern railroad, runs 78 miles in a NE. direction to the mines, which are its northern terminus. The railroad was built about 1890, practically on account of the Sierra Mojada mining-district. 1 Sierra Mojada, Mexico, by Richard E. Chism, Trans., xv., 542 (1886-87). 2 The Sierra Mojada, Coahuila, Mexico, and Its Ore-Deposits, by James W. Malcomson, Tram., xxxii., 100 (1901).

Aug 1, 1912

By Ming-Kao Yen

A considerable amount of work has been reported in the literature in regard to the texture and earing behavior of copper strip. The rolling texture of copper has been confirmed as (110) [112] and (112) [111], which yields ears of a drawn cup at the position 45" from the rolling direction.1-3 The recrystallization texture has been established as the cubic or (100) [001] texture, where the earing positions are at 0" and 90" to the rolling direction.4-8 It has also been reported that in the development of cubically aligned grains of copper strips, the percentage of this cubic texture increased with an increase of final reduction and final annealing temperature.8,9 A comprehensive study on H.C. copper (British commercial copper of high-conductivity quality = Cu 99.95 pct, O2 0.03 pct, Ag 0.003 pct, Fe 0.005 pct and Pb < 0.001 pct) was made by Cook and Richards.6 They concluded that the recrystallization textures could be described as one or more of the following textures: (1) a single texture (100) 10011, (2) a twin texture (110) [112] and (3) a random orientation, depending upon the previous history of the specimen concerned. The effect of various alloying additions in copper was reported by Dahl and Pawlek.10 They found that certain alloying additions, such as 5 pct Zn, 1 pct Sn, 4 pct Al, 0.5 pct Be, 0.5 pct Cd, or 0.05 pct P suppressed the formation of cubic texture. Brick, Martin and Angierll reported that the cold rolled textures due to various additions fitted a rather simple pattern. However, the recrystallization textures were subject to very considerable variations. In the discussion of this paper, Baldwin stated that deoxidized copper containing 0.02 pct P gave a complicated recrystallization texture at lower temperature. When this copper was annealed at high temperature, a single texture appeared which was described as (110) [ill] but. according to a pri- vate communication from Baldwin, this orientation reported was in error and should have been reported as (110)[112]. He also reported that the earing positions of drawn cups were at 60" to the rolling direction.12 Recently, Howald, in his discussion on the paper by Hibbard and Yen,13 reported that the rolling texture of phosphorus deoxidized copper, containing from 0.006 to 0.020 pct phosphorus, was of the pure copper type. When these coppers were annealed at lower temperatures, they exhibited a random orientation, and when they were annealed at higher temperatures they had a mixed (111)[110] and (100)[001] texture, depending on the severity of the final reduction and annealing temperature. However, the specific influence of phosphorus and other impurities on the recrystallization textures and the deep drawing properties of copper strip has not been thoroughly reported. Therefore, an attempt has been made in the present work to determine the rolling and recrystallization textures and also the earing behavior of five types of commercial copper and thereby to evaluate the effect of phosphorus and some other significant impurities on the development of texture for cold reductions of about 87 to 89 pct. Materials Used The five types of copper employed in the present investigation were two phosphorus deoxidized coppers of different phosphorus content (0.007 and 0.013 pct P), an oxygen-free copper (OFHC), an electrolytic tough-pitch copper, and a fire-refined tough-pitch copper. These materials were subjected to a thorough spectroscopic and chemical analysis. The designations and the chemical compositions were as shown in Table 1. The coppers, FA1, FA2 and FA3. were hot-forged from 3-in. billets into a ½ X 6-in. plate and cold rolled to the ready-to-finish gauge indicated below. FA4 and FA5 were hot rolled and scalped to ready-to-finish gauge. The grain size of all the materials in the ready-to-finish condition was about 0.030 to 0.045 mm. Table 2 shows the last stage of the production schedule for each copper strip used. Experimental Procedure ANNEALING, GRAIN SIZE AND HARDNESS DETERMINATIONS Specimens of each type of copper were finally annealed in air for periods of one hour at temperatures ranging from 300 to 1600°F and were subsequently cooled in air. The average grain diameter of the annealed specimen was estimated by comparing with a standard grain size chart. Hardness was determined on the Rockwell 15 T scale. CUPPING TESTS Cups were made in a blanking and drawing set, in which blanks of 2-in. diam were drawn to a cup of 1.25-in. diam with an average depth of about 0.75 in. The clearance between the punch and die was about 0.032 in. The ears of the cup were measured with a special fixture which read the height of ears to one-thousandth of an inch on every ten-degree interval along the circumference of the cup. POLE FIGURES The usual transmission diffraction method with unfiltered copper radiation was employed to determine the pole-figures of the specimens cold-rolled or annealed at 900°F. All the pole-figures were derived from the positions of intensity maxima on 111 diffraction rings of the X ray photo-grams taken at 10 rotation of a

Jan 1, 1950

By Paul D. Merica

DURING the Dark Ages, when metallurgy was practiced by the alchemists, any unusual or disturbing variation in metallurgical operations was ascribed to the, presence, in the metals or ores, of an evil spirit, and it was necessary to exorcise and drive it out "by suitable incantations. In this day of science and of engineering, things still incomprehensibly go wrong in the metallurgist&apos;s work shop. The metallurgist is even now not unwilling to lay the blame for many such experiences at the door of something which intellectually- much resembles an evil spirit, "gas in the metal." The presence of gases in his metal, he knows, occasions him many very definite troubles which he can clearly distinguish and diagnose-why may it not be also responsible for those which he cannot so well understand?

Jan 1, 1931

By J. M. McDowell

A study has been made to deter~r~irre how the behavior of a water drivee reservoir changes as a function of the permeability of the formation and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rote of nat11rn1 water influx is also studied, (IS well as the influence on the influx of the position of water injection we1ls with reference to the oil-water contact. The results are determined by the use of an electrical reservoir analyzer and are plotted as families of curves of pressure, natural water influx, and water injection vs time or cumulalive production. Two size aquifers are studided. One is limited with a 36-inile radius, and the, other approximates an infinite reservoir. The field remains the same in all respects for the completed. study except that the permeability is changed to agree with that assumed for the aquifer. 1 N TR ODUCTI ON this study was undertaken in -dcr to determine how the pres- sure decline and water influx of a water drive field would change as a function of the rate of fluid withdrawals, as a function of the permeability of the formation, and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rate of natural water influx was also studied as was the position of water injection wells with reference to the oil-water contact. The information has been determined by the use of an electrical reservoir analyzer1, sometimes referred to as a Carter type analyzer. This instrument is an analog type computer which can be set up to represent a water-drive oil field. It can reproduce the past performance of the field in terms of analogous electrical quantities when the proper circuit analog of resistors and condensers has been determined, also, it can determine the future behavior for any method of production which may be selected, or permit the comparison among several different methods. Although most applications of the reservoir analyzer"" have been to thc study of specific field performance, it is intended to use the analyzer here to help understand how various reservoir characteristics effect the final performance of the field and to sec under what conditions water injection will be of benefit and to what extent. Within the oil industry the performance of water-drive reservoirs was first described analytically by LV. Hurst&apos; and M. Muskat2 for certain types of boundary conditions. The solutions of the equations developed involved products of exponential functions and Bessel functions. Later publications by Hurst4 and van Ever-clingen" and the hooks of Muskat6 gave further information on reservoirs with other boundary conditions. They also presented rather extensive curves and tables to help evaluate the analytical expressions involved. A rccent series of publications by Chatas. bascd on the work of Hurst and van Everdingen, gives quite complete charts and tables of data to evaluate the pressure decline or water influx in infinite or limited radial reservoirs. and in linear reservoirs. The curves in all of these publications are given in dimensionless form

Jan 1, 1956

By J. W. Snavely

WITH all the advantages of handling bulk materials by means of belt conveyor also go some problems, one of the most persistent being that of cleaning. When sticky materials are being carried; the build-up of material on the return idler rolls results in difficulty of belt training. Much attention has been given to the problem of cleaning conveyor belts, and a great variety of cleaning devices have been developed. Even the best involve troublesome maintenance, and none can completely remove the fine particles imbedded in the belt cover, which cause rapid wear of the return idler rolls, and at the same time, of the belt cover as well. One of the major rubber companies has been promoting a two-way belt system, in which the conveyor belt is given two successive 90" twists at each end to enable it to carry material in both directions simultaneously. For many years the flat belt transmission industry has installed quarter-turn and half-turn twists in countless numbers of instances. While quarter-turn and half-turn twists in transmission belts is a familiar application, the 180" twist apparently has never been previously attempted with a conveyor belt. About a year ago, two officials of the National Iron Co. of Duluth, Lester and Lewis Erickson, proposed twisting the return run of a conveyor belt on an installation that they were designing for one of the major iron ore producers. Since then the soundness of the idea has been demonstrated, both in theory and by practical test, with the result that the installation of two conveyor belts involving the twisting of the return run is now under way. These two installations are designed to have the return run of the conveyor belt twisted 180" as it leaves the snub pulley at the head drive. The clean underside of the belt is thus placed against the idlers on the return run as well as on the carrying run. Just before it enters the tail pulley, the belt will be twisted an additional 180°, restoring it to its normal position. Because this twisting of the return run of a conveyor belt is a radical departure from accepted practice, an elaborate and extensive test was conducted early in 1950 to demonstrate that this twisting of the return run could be done successfully, also to establish application data for accomplishing this twisting, and to determine if any special equipment would be required. In studying this concept of twisting the return run of a conveyor belt, a number of problems need to be solved, primarily the ones brought about by deliberately introducing an unequal distribution of stress across the conveyor belt and controlling that maldistribution of stress, while confining it to the return run portion. The tension conditions existing in the return run of a conveyor belt are clear to all designers. First, the return run carries the initial or slack side tension of the conveyor belt, the tension that must be supplied to the return run to provide proper frictional contact between the belt and the driving pulley so that the necessary power can be transmitted from the driving pulley to the belt without slippage. This slack side tension is supplied to the belt by means of takeups, either of the gravity type, which can be vertical or horizontal, or by means of the screw type. With inclined or declined belt conveyors the slope tension also must be considered, which is the tension imposed by the weight of the belt hanging from the top pulley. This slope tension frequently can furnish part or even all of the initial tension required. The maximum value of the slope tension will be at the top pulley, and it decreases in direct proportion to the length. In addition to the foregoing, it frequently is desirable to impose arbitrarily additional slack side tension to provide sufficient tension at the loading point at the tail, so that the belt will adequately support its load between the carrying idlers. Design Conditions for Twisting A number of design conditions exist, which must be satisfied successfully to accomplish the twisting of the return run without exceeding normal working limits in any portion of the conveyor belt. It is obvious that the belt edge, in its relation to the center of the belt, must stretch in making a twist, because as the twist is accomplished, the belt edge travels through a longer path than does the center of the belt. It is further obvious that if the edge of the belt is stretched, a redistribution of stress in the belt is required to allow this edge stretching. Moreover, this stress will be unequal across the width of the belt, having a maximum value at the edges, with a minimum value at the- center of the belt. With correct initial tension in the return run of a conveyor belt, the existing slack side tension will be unequally distributed when a twist is introduced. A condition then exists in which the edge stresses,

Jan 1, 1952

By Edward H. Robie

HOW have recent events affected the general trend in world mineral production? What effect has the World War, with its resultant boom and depression, had on the long-term trend of output? Have all of the principal metals and fuels been similarly affected, or have some boomed or slumped much more than others? The trend of world production of coal, iron, the principal nonferrous metals, and petroleum is shown in the accompanying chart, covering the period from 1882 to 1931 inclusive-the last fifty years. The curves are plotted logarithmically to show the comparative trends. In the lower left-hand corner of the chart is a slope diagram to aid in visually evaluating. the average yearly rate of increase in production; from this one can easily see, for example, that the petroleum production curve indicates an average annual increase of around 8 per cent, and that up to the period of the World War the average annual increase in copper production was about 6 per cent.

Jan 1, 1932

By Virgil Miller, F. B. Petermann, S. F. Ravitz

The Cle Elum nickeliferous iron deposit is in Kittitas County, Washington, in a rugged, mountainous region about 23 miles north of the town of Cle Elum. The Biewett Pass deposit, which is similar in character and occurrence, is in Chelan County, about 18 miles east of the Cle Elum deposit. A more or less continuous ore zone may extend between the two deposits, since iron ore is reported to have been discovered at Iron Mountain, which lies directly between them. The ore probably was formed by meta-morphism of laterite resulting from Ieach-ing of serpentine derived from peridotite. It consists largely of magnetite grains distributed through a matrix of limonitic material containing a small amount of hematite and chromite. Many of the chromite grains have shells and inclusions of magnetite. The magnetite grains range in size from 1200-mesh to 1/4-in., the average size being 48 to 65-mesh; the chromite grains range from 20 to 150-mesh. The gangue minerals are olivine and serpentine with a small, amount of chlorite, and appear both as very thin bands in the ore and &apos;s minute fragments in the limonitic matrix. The nickel is present as minUte inclusions of a nickel silicate mineral within the magnetite and gangue par- ticles, varying in size from 1500 to about 280-mesh. Detailed analyses of 3000-lb. lots of Cle Elum and Blewett Pass ore are given in Table I. TABLE i.—Analyses of Ore Samples Per Cent Ore from Constituent cle Elum&apos; Blewett Pass Cr....................... 2.23 2-12 Ni...................... 1.43 0.9s Fe...................... 52.9 41.4 SiOz.................... 5.6 13.4 CaO.................... 0.3 0.8 MgO................... 4-1 7-5 AI2O3................... 7.0 2.g P...................... 0.022 0.034 S....................... O.O1 o.oa Mn..................... I.I 0.4 Ba..................... nil co..................... o.oa 0.02 CU..................... 0.02 0.03 As...................... 0.03 Au..................... nil Ag°..................... O.58 Pt...................... ml Fe++.................... 8.9 5-9 Fe+++.................. 44-0 35-5 « Ounces per ton, 1 sr,cte,so,","&&$ally absent: B, W, M~, T~, V, ~i, Bi, Pb. Sb. Sn. Be, In, Hg. Zn, Zr. Cd. Preliminary Tests Attempts to beneficiate the ore by ore-dressing methods, including various &apos;cornbinations of sink and float, tabling, jigging, flotation, and magnetic separation, were consistently unsuccessful. A wide variety of roasting and leaching tests were made on both raw and reduced ore, but in most of the tests little or no nickel was extracted, and in none did the extraction exceed 50 Per cent. No nickel could be volatilized as the carbonyl. by treating reduced ore with carbon monoxide. Fairly good sepa-

Jan 1, 1944

By John J. Gilman

BECAUSE of their layerlike structure, zinc crystals exhibit strong anisotropies for almost all physical and chemical properties. This should, and indeed does, greatly influence the plasticity of zinc for various crystal orientations. At low temperatures, the investigator of this plastic anisotropy is plagued by the great variety of deformation modes that operate. However, at high temperatures (250° to 419°C) only two deformation modes predominate: basal (0001) and prismatic (1010) glide. Furthermore, since strain hardening is virtually absent at high temperatures, the plasticity for these two modes of deformation can be very simply described by means of two equations of state. It is the purpose of this paper to describe the experimental behavior of basal and prismatic glide in zinc crystals, and to interpret this behavior in terms of other physical properties (in particular, the thermal expansion coefficients and the elastic constants) using the theory of dislocations. Fig. 1 defines the two planes of the zinc structure that will be discussed. Glide occurs very readily on the basal planes at all temperatures, and there is a very large literature on this subject. Much of the literature has been reviewed by Schmid and Boas;&apos; it will not be reviewed here. Kolesnikovl was the first to show that if basal glide is circumvented by stressing a zinc crystal parallel to the basal planes (giving zero shear-stress on the basal planes) then, at temperatures above about 320°C, glide on the first-order prism planes occurs. His results have recently been confirmed by Cahn, Bear, and Bell." These previous workers have established the existence and crystallographic elements of prismatic glide; the present paper is concerned with the stress, strain rate, and temperature relations of prismatic glide as contrasted with basal glide. Experimental Methods The crystals were square ones, 6x6 mm, that had been grown in precision Pyrex tubes by a method that is described in detail elsewhere.&apos; Most of the crystals were 99.999+ pct Zn (New Jersey Zinc Co. CP grade). Some were alloyed with 0.1 -+-0.005 atomic pct Cd, and chemical analysis showed that almost all of the added cadmium persisted through the crystal-growing process. For measurements of nonbasal glide, crystals were oriented with their basal planes parallel to both the rod axis and one of the flat faces of the square cross section. However, the orientation of the close-packed directions [1210] with respect to the rod-axis was variable. For basal glide measurements, the angle between the basal plane and the specimen axis was 35". The orientations were measured by the Gren-inger back-reflection X-ray method. The problem of finding a suitable method of gripping the crystals was the most serious experimental obstacle that arose. Because of the large plastic anisotropy of zinc, the usual gripping methods were unsatisfactory. Some methods that were tried were: high melting-point solder, making heads on the ends by locally melting a crystal, and electroplating nickel on the ends to form enlarged portions. For all these methods, the regions of the grips were weaker than the crystals themselves. Finally, two methods were decided upon: bend tests and direct machining of tensile specimens. In the bend tests, specimens were loaded as simple beams so that gripping was not a problem. The beams were 1 in. long and the axis of bending was parallel to the hexagonal axis of the crystals. For the crystals that were machined into tensile specimens, brass bars with slots in them were used to support the crystals, and thereby minimize the distortions due to machining. The crystals were glued into the brass bars with plastic cement which was later dissolved away with acetone. See Fig. 2, left. No clamps were used near the crystals and the machining was done using a milling machine with a fly-cutter. The tool bit was very sharply pointed to minimize burnishing. The feed was less than 1 mil per cut. The depth of cut was 2 mil for roughing cuts, and % mil for the finishing cuts. This machining method produced surface layers of tiny recrys-tallized grains only 2 to 3 mil deep, and the bodies of the crystals were not measurably disturbed. After the crystals had been machined and removed from the brass holders, they were chemically polished until about 5 mil had been removed from all their surfaces. The polishing reagent consisted of equal parts of concentrated HNO,, 30 pct H3O and ethyl alcohol; it is described in detail elsewhere." A typical crystal is shown in Fig. 2, right. The I-shaped faces are normal to the hexagonal axis of the crystal; otherwise the projections at the ends would simply shear off when the crystal was loaded. The cross section in the 2?-in. gage length is 0.215x0.115 in. It was found that the polished

Jan 1, 1957

By Walter V. Knopp, Laurence Delisle

INTRODUCTION THE aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixture of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion corresponding to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low cost material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, i.e., finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemental powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: 1. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. GENERAL PROCEDURE The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1948

By Whitman E. Brown, Louis J. Erck

The installation in 1948 of a Hum-phrey~ spiral concentrator section at the Hill-Trumbull plant of The Cleve-land-Cliffs Iron Co. is the latest commercial method on the Mesabi Range being used for the recovery of fine iron ore. In two stages of concentration 84 spirals treat approximately 120 long tons per hour of minus ? in. ore. These spirals augment the production of the heavy-density plant which recovers the plus 36 in. iron from the plant crude ore. Structure of the ore is such that, when crushed, about 50 pct of the plant crude is minus ? in. size. After de-sliming in a 66 in. Akins classifier, grinding the classifier product in a ball mill and again desliming in a 78 in. Akins classifier about 15 pct of the crude ore remains to be treated in the spiral plant. Overall recovery of the ball mill feed in the Hill-Trumbull spiral plant during the 1948 season was about 53 pct of the weight and 66 pct of the total iron content. Of the actual feed delivered to the spirals from the 78 in. classifier 64.9 pct of the weight was recovered containing 73.7 pct of the total iron. The average analysis of the spiral concentrate is 55.05 pct Fe and 14.83 pct SiO2. An average of mill assays during the 1948 season is given in Table 1. The Hill-Trumbull plants treat both wash ore and jig-type ore. During the 1948 season spirals were used only on the fine sizes of jig-type ore. At times the deslimed minus ? in. size is of sufficient grade to warrant bypassing the spirals but in the main the fine size is delivered to the 48 first stage spirals and thence to the 36 cleaner or second stage spirals. In the past several years numerous Mesabi Range ores in the fine size cate- gory have been tested by a wide variety of beneficiating equipment. The prodigious amount of research devoted to the recovery of values in the fine ore reflects the dire need of the iron industry to squeeze the last possible unit of iron from the mined ore and to develop suitable equipment and processes to satisfactorily concentrate the leaner horizons as they are encountered in the process of mining. Large governmental and private appropriations have been allotted, new laboratories built, research and technical staffs increased, and operator-manufacturer cooperative agreements applied to hasten the solution of the problem. The University of Minnesota, at its Eighth Annual Mining Symposium in January 1947, dedicated as its objective the bringing to light of technological developments in iron ore beneficiation. Papers were given at that time relating to processes being developed. Specifically, these papers reviewed flotation, Baum jig, selective media concentrator, Hardinge concentrator, Dorrco sizer, heavy media concentration, Hydrotator, and the Humphreys spiral. The Cleveland-Cliffs Iron Co., after encouraging results from tests in a small pilot plant using one full size spiral, made the first commercial installation of Humphreys spirals on the Mesabi Range at their Hill-Trumbull mine, Taconite, Minn. This company

Jan 1, 1950

By AIME AIME

FOR the development of a mine, a shaft of small cross-section is usually sunk, of no larger size than is absolutely necessary. After the mine has been developed and put on a production basis it is a common practice to sink a shaft of larger cross-section for hoisting and use the original shaft for the handling of men and material into the mine. While that ar¬rangement is usually expedient, the small size of the supply cages presents a problem in the handling of ma¬terial. Where a cage is, say, 4 by 4 ft., which is not an uncommon size, all lengthy and bulky material must be handled piece by piece several times from the supply department to the underground stations. Thus drill steel and timbers over 4 ft. long will be loaded on cars at the supply department and wheeled to the shaft, where each piece must be unloaded from the cars and stood up in the cage. They are then lowered to the shaft station, unloaded piece by piece and placed in cars, run to the supply station and again unloaded and stored until called for. In such a case handling becomes a major item in the cost of supplies.

Jan 1, 1930