Search Documents

By Walter Rose

Theoretical expressions are presented to describe wetting and non-wetting phase relative premeability relations. These expressions have then been compared with existing published data, the conformance noted being sufficiently good to satisfy the requirements of some engineering use. As a consequence, it may be supposed that relative permeability characteristics of porous media now can be inferred from basic core analysis data, in a manner more convenient (although less direct) than presently available methods of experimental evaluation. INTRODUCTION This paper presents a new approach to the problem of relative permeability evaluation. A classification of published discussions of relative permeability concepts which have appeared in the petroleum literature will show that previously emphasis has been placed on methods of experimental measurement, on the interpretation of the data so obtained with respect to the variable properties of the system, and on theoretical and practical considerations which relate relative permeability to gross fluid behavior in petroleum reservoirs. Essentially, no detailed examination has appeared which treats the fundamental factors controlling the quantitative features of the relative permeability relation*, although cer- tain references can be Cited where a qualitative awareness of their existence and nature is indicated. This condition is explainable in terms of the recognized complexity of the problem, and in order to provide some basis for theoretical development, the general emphasis has been placed in the past on experimental procedures of evaluation, the validity of which, in principle, could be confirmed by the analysis of well and reservoir performance. However, because of the experimental difficulties which have been encountered (notably, difficulties due to the so-called "end effects"), and because of the general unreliability of field performance tests required to study the applicability of the data, relative permeability phenomena continue to be incompletely understood and described.? In this paper is examined the possibility of predicting relative permeabilities entirely from fundamental considerations. In addition, attention is called to certain important factors, previously unemphasized in the published literature, which now can serve as a basis for the eventual experimental confirmation of this and similar theoretical approaches, as well as the experimental solution of the problem in general. Therefore, the analysis presented herein has the dual purpose both of orienting future experimental activity and also of providing an immediate solution for the relative permeability porblem, sufficiently adequate for some engineering use. It will be seen that the conclusions reached are supported by theoretical and intuitive considerations, and they are not contradicted insofar as gross features are concerned by existing concepts and interpretations of published experimental data, except as specifically noted. Darcy's law, expressed simply as: k dp q = k/u dp/dx .......(1) where q is linear rate of flow (assumed horizontal), k is the † The poor comparison usually obtained between laboratory and field gas-oil ratios (c.f.. Fig. 4 of paper by L. E. Elkins) is illustrative of conditions which dimcourage unqualified acceptance of the results of previous studies except as presently useful approximations. In this connection, Evinger and Muskat have discussed in detail the discrepancy observed between field well productivity values and values obtained from the analysis of laboratory flow data.

Jan 1, 1949

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1940 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal Mining, B-Milling and Concen-tration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which was issued quarterly in 1940 but will be issued every other month in 1941. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysical Methods of Exploration are issued as separate pamphlets. An Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CONTRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute accord-ing to their registration by classes. CONTRIBUTIONS and other TECHNICAL PUBLICA-TIONS will be sent upon request. A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent a page; minimum charge, 25¢. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1.25 domestic, $1.35 foreign countries. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum domestic, $2.50 foreign. METALS TECHNOLOGY, $7 per annum domestic, $7.80 foreign (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum domestic, $6.60 foreign (metal mining, milling and concentration, Industrial Minerals Divi-sion, and mining geology papers.) PETROLEUM TECHNOLOGY, $6 per annum domestic, $6.60 foreign. Bound volumes have been mailed to members that have requested them, and MINING and METALLURGY is mailed each month. A member is entitled to one volume a year on his membership and he may purchase for $2.50 one copy of a volume not already received; additional copies of the same volume, $5. Nonmembers may pur-chase the volumes listed, at $5 each, plus 60 cents for Canadian or foreign postage. Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 50¢ each to members; to nonmembers 506 current issue and $1 each, back issues. Subscription price to nonmembers and to members for extra copies, $3 per annum domestic, $4.00 foreign.

Jan 1, 1940

By Dr. O’Neil Thomas J., Donald W. Gentry

"Who is the man who views the mines and promptly turns them down? Who is the one that thinks this is the short cut to renown? Who is it gives the bum advice to the innocent financier? The knowledge-feigning, theory- straining mining engineer." -Anonymous INTRODUCTION Taxes levied against mining properties and operations are a critical cost in the economic evaluation of mining investments. Indeed, taxes represent a substantial cost of doing business in the minerals industry and often have a significant impact on corporate investment decisions. A good example was the postponement of mineral development in the state of Wisconsin, primarily because of what was perceived to be excessive taxes imposed by that state. In many respects mining investments are no different from other industrial investments. Astute taxing authorities should recognize that geologic endowment is a necessary but clearly not a sufficient condition for mineral investments. The fact that a mineral deposit exists does not necessarily mean that it will ultimately be developed-a point that many taxing authorities fail to recognize. While it is true that ore deposits are not mobile in the sense that they cannot be physically moved to a district having more favorable taxes, corporate investment capital certainly is mobile and flows to ventures which maximize wealth to the firm. In short, higher taxes reduce project yields and tend to drive investment capital elsewhere. The appropriate type and level of taxation imposed upon the mining industry continues to be a very controversial and emotion-charged topic. Mining activities have been taxed at various levels over the years due to widely differing taxation philosophies. Location has also influenced taxation policies, as evidenced by the diversity of tax laws and assessment procedures applied to mineral deposits by the various states. Indeed, mineral taxation varies from state to state, from county to county, and from one mineral commodity to another. Whether or not a given tax is appropriate for a specific mineral deposit, or even an industry, is a difficult problem to assess. First, the type or kind of tax which should be imposed must be considered. Second, it is most important to define a fair and unambiguous base against which to levy the tax. Finally, one must consider the tax rate to be applied to this base. It is the combination of these two components

Jan 1, 1984

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.' The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.' The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By John Dorn

THE phenomenon of diffusion, according to the most prevalent conceptions at the present time, undoubtedly played an important part in the formation and distribution of metals and minerals in the earth's crust. Apparently there is good evidence that in the geological rate of cooling diffusion caused numerous materials to separate into individual masses or into duplex structures. As is well known, the early steels were made by cementation; that is, by heating wrought ferrous metal in contact with carburizing materials so as to produce a relatively high carbon content on the surface. If the process was continued long enough, the carbon diffused throughout the piece. A more homogeneous product depended upon further heating and forging, so that the carbon diffused to a fairly uniform concentration throughout the metal. In the modern metallurgical industry, diffusion is the basis for many operations; for example, the production of hard surfaces oil steels by carburizing, nitriding, cementing with chromium, silicon, boron and beryllium. Castings or ingots as they solidify do not have homogeneous structures, but these structures are made largely homogeneous by suitable process of heat-treating and the resulting diffusion. It is in modern physical metallurgy, however, that we become greatly concerned about the mechanism of the phenomenon of diffusion. The rates of diffusion, effect of temperature and time on diffusion, and the relation of diffusion to the many properties of the parent metal and the diffusing metal have become important; also, we are concerned with the diffusion of a single metal into a complex alloy. For example, what is the mechanism whereby carbon and nitrogen travel into steel? What is the effect of alloying elements in the ferrous material on the rates of diffu-sions? What is the effect of simultaneous diffusion of carbon and nitro-gen? How does chromium, beryllium, boron, or the like, diffuse into the steel, and what are the effects of alloying elements in the steel previous to the cementation process? These inquiries are by no means limited

Jan 1, 1937

By C. B. Dudley

In October, 1878, and again in February, 1881, I had the honor to make public, through the medium of the American Institute of Mining Engineers, the results of an extended study of steel rails which had been in service, and which mere taken for the purpose from the tracks of the Pennsylvania Railroad Company. These studies appeared in three papers. In the first of these papers the question. what kind of steel is least liable to fracture or disintegration in the track, was the principal one considered. In the second paper the question discussed was, does the power of steel to resist wear increase with the hardness ? In the third paper the relation between wear and the chemical and physical properties of the metal was the principal point considered. The general results arrived at, or the cooclusions reached, were, as follows: 1. That a mild steel is less liable to fracture, and if properly made, less liable to crushing or disintegration in the track than a harder steel. 2. That the wearing-power of steel in rails not only does not increase as hardness increases, but, on the contrary, diminishes; or, in other words, that a mild steel gives less loss of metal under the same service than a hard steel. These conclusions may be briefly stated in a single sentence—namely, in rails mild steel is not only less liable to fracture and disintegration in the track, but it also gives longer life, or wears more slowly under the same traffic; than harder steel. It is perhaps hardly necessary to add that by mild steel is meant steel

Jan 1, 1891

By T. G. Digges, C. L. Vold, M. R. Achter

A study was made of the effect of the growth conditions on the perfection of single crystals of niobium (columbium). Dislocation densities, determined by means of double-crystal diffractometer measurements , were not greatly affected by the method of crystal preparation but could be reduced by annealing treatments. However, the size, sharpness, and tilt angles of the substructures, observed with X-ray reflection macrograph, were sensitive to variations in growth procedures as well as to subsequent thermal treatments. Although the dislocation density was the same in both types, there were more low-angle bound-aries in crystals grown by zone melting than in those prepared by strain anneal. Mechanisms to account for these observations are discussed in terms of dislocation movements. A planned study of the structure-sensitive properties of refractory metals required the use of single crystals of a high degree of structural perfection and, for ease of handling, of large cross section. It appeared that the strain-anneal technique could satisfy both of these requirements. First, crystals grown in the solid state have been reported to be more perfect than those obtained from the melt.' Second, the diameters of rods which may be produced by zone melting should have a theoretical limit determined by specific gravity, thermal conductivity, and surface tension, while the diameter of strain-annealed rods is limited only by practical considerations. Previously it was shown that niobium (columbium) single crystals of 1 in. diam2 may be grown by strain anneal, compared to the 0.5 in. maximum diameter achieved by zone melting, as reported for molybdenum by Belk.3 The current research was undertaken to investigate and optimize the effect of various process variables on the perfection of 1/4 and 1/2-in.-diam niobium single crystals grown by strain annealing and to compare their perfection to those grown by zone melting. Characterization of these crystals was more conveniently accomplished by means of X-ray than by metallo-graphic techniques. EXPERIMENTAL PROCEDURE Specimen Preparation. Zone-melted crystals of 1/4 in. diam were produced by the standard electron-beam zone-melting technique. The swaged and cleaned rods were outgassed, in the solid state at a temperature near its melting point, at a rate of 12 in. per hr, and single crystals were grown by making two molten passes at 2 in. per hr. By maintaining a zone length of 4 to % in., very uniform single crystals several inches long were obtained. For the strain-annealed crystals, an induction heater was used, in preference to other types of heating, to take advantage of the good penetration of large sections. A five-turn coil, 1 in. long, operating at 10 kc and powered by a motor generator, was contained in a vacuum chamber. The rod, suspended from the upper end, was raised through the coil for both recrystallization and crystal growth. In preliminary work single crystals of the same material were also grown with single and multiturn coils powered by a 450-kc generator. A vacuum of 2 X 10-6 Torr was maintained at temperatures up to 2400°C. Starting with electron-beam-melted ingots of 21/2 in. diam, the analysis for which is given in Table I, the material was cold-swaged to the desired cross section of 1/4 and 1/2 in. diam and then recrystallized. The rods were then strained in a tensile machine and converted to single crystals by passing through the induction coil. As with zone melting, control of orientation is possible by the use of special procedures. Other investigators, see for example Williamson and smallman,4 have reported that orientation control may be achieved by a bending technique. In the present work the strained rod is partially lowered through the coil to start the growth of the crystal. Then it is removed and bent at a point in the poly crystalline portion. Finally, it is returned to the chamber and growth is continued "around the corner". This procedure has certain limitations. If the bending operation exceeds the critical strain, recrystallization may take place. Also, the amount of bending which can be imparted to the rod is limited by coil geometry, and up to now has been 10 deg. However, by repeating the bending and growing operations it should be possible to attain any desired orientation. In preparation for X-ray examination, single crystals were sectioned and planed by means of the spark-erosion technique. To obtain the maximum reflected intensity, the (110) plane was exposed for examination. They were then etched 3 to 5 min in a mixture of con-

Jan 1, 1967

By W. P. Evans, R. W. Buenneke

Warren and Averbach's multiple order, Fourier method was applied to solid specimens of SAE 1045 steel. The material was hardened to three hardness levels and specimens of each hardness were shot peened to three intensities. Particle size, root-mem-square strain, mean strain, md macro residual stress were determined for each. Microstrains caused by either hardening or peening varied markedly over microregions. In general, increasing the hardness or peening intensity increased the rms strain and decreased the particle size. Similar effects were observed by varying hardness and peening intensity independently. At a Rockwell hardness of C 50, peening had little effect on line broadening, but both mean strain and macro residual stress increased. Mean strain was independent of column length. Induced macro residual stress by peening was affected most by initial hardness, but not by specific peening intensity. The purpose of this work is to establish the state of residual strain and particle size by X-ray diffraction in hardened and cold-worked plain carbon steel and attempt to relate these X-ray measured parameters to fatigue performance. X-ray line broadening (and its micro implications), along with X-ray residual stress (and its macro implications), may be basic indicators of the inherent fatigue resistance of the material. X-ray line broadening is caused by variable lattice strains and small particle size. Both are a result of plastic deformation which accompanies hardening or cold working processes. Therefore, X-ray line broadening is a good measure of both. warren1 has recently reviewed the Warren and Averbach2,3 Fourier analysis of line broadening. Strain and particle size effects can be separated because broadening due to particle size is independent of order of the diffraction peaks, while broadening due to strain is not. Microstrain is obtained as a root-mean-square strain averaged over discrete distances within the crystals causing diffraction. These distances are quite small, varying from 10 to 10081, and may be interpreted as the gage length over which the strains are averaged. Because of their variable nature, the X-ray line is broadened. The plot of rms strain vs distance (or column length) within the specimen gives a measure of their variability. Small particles also cause X-ray line broadening as already mentioned. A particle is interpreted as a region within a crystal or grain which diffracts X-rays coherently. This region is one of given orientation and may be bounded by a small angle grain boundary, dislocations, a twin boundary, or a stacking fault. The present work covers measurement of X-ray line broadening and macro residual stress on an SAE 1045 steel, quenched and tempered to various hardnesses. Various amounts of cold working were produced by shot peening the surfaces to various Almen intensities. Particle size, root-mean-square strain, and mean strain were calculated from the Fourier coefficients of the X-ray diffraction profiles in a direction normal to the peened surface. No effort was made to separate the various causes of particle size broadening. Macro residual stresses were reported in directions parallel to the peened surface. I) X-RAY METHOD The Fourier coefficients were determined for the 110 and 220 X-ray profiles. They were corrected for instrumental broadening by the method of Stokes,4 using an annealed reference specimen of similar geometry presumed to be free from broadening due to small particles and distortions. The nth Fourier cosine coefficient, A,, is related to a particle size coefficient, Ap, and a distortional coefficient, ADn, by the equation:

Jan 1, 1963

By C. M. Kleeman

All mines have a finite life and the time comes when the ore is depleted, or it has become uneconomical, or for some other reason which may be peculiar to that particular mine, it must be shut down. The operation at that point of time still has some assets such as mining and milling equipment, workshops, and in the case of a gold mine, an unknown quantity of gold which has been trapped in the treatment plant. Recovering this gold can be done at small cost and can be extremely profitable. Recovery of these hidden assets requires a good knowledge of the treatment plant, i. e. , as say values of heads, tails, and of the products produced; and if mercury for amalgamation was used, where? A careful study of available plant records can be extremely valuable in forming a working plan for adequate recovery. In the following paragraphs the various unit operations and equipment where gold can collect are described and suggestions made for its recovery. Subsequently, a case history will be given for dismantling a gold plant which had a complex flowsheet and which had been in operation for many years. Looking for trapped gold in a crushing section would invariably not be worthwhile since crushing is normally a dry process and there would be few areas where free gold could collect. In the milling section, however, many areas can literally become small gold mines in themselves. Material in the bottoms of grinding mill scoop boxes can be high-grade, and even the scale on the sides of the boxes should be scraped off and collected. Mill liners should be removed and all scale, rust, and residue collected. Residue in the bottoms of rake or spiral classifiers, if they have been used, should be removed as should the scale and rust on the sides of pump sumps, launders, etc. The following procedures should be used to extract gold from these collected materials. All steel (ball scats) should be removed, screened out, and reserved. Fine material should be placed in an amalgam barrel, water added and ground with the amalgamation tailings being sampled and assayed. If high-grade, tails should be reserved; if not, discarded. The coarse material that was screened out should be placed in a heap, regularly sprayed with water and allowed to rust. After several months this material should be screened again and the fines amalgamated.

Jan 1, 1981

By M. R. Tek

A new method for correlating the data on multiphase flow through vertical pipe is presented. The correlation is based on a "two-phase f factor" concept which was developed and successfully applied to horizontal multiphase flow by Bertuzzi, Tek and Poettmann. Field data previously published on several flowing and gas-lift wells have been used as the basis for the developed correlation. The application of the method to actual two-phase flow problems indicate that this method is capable of predicting the pressure distribution in vertical multiphase flow strings well within the accuracy range usually desired for common engineering and design calculations. A new working chart developed for calculation of two-phase pressure gradients and a graphical step-by-step procedure for the computation of pressure distribution are presented along with an example problem. INTRODUCTION Multiphase flow through vertical pipe is encountered in many engineering installations. In petroleum, chemical process, nuclear engineering and many other industries, problems associated with simultaneous flow of two or more phases through vertical pipe have been of interest for a long time. This interest has increased considerably during recent years due to applications to new processes in petroleum production and refining and to problems of steam generation and heat removal from nuclear reactors. One prominent example of vertical two-phase flow is provided by the gas-lift process where oil, water and gas flow simultaneously. If the pressure profile in a gas-lift well can be predicted within reasonable accuracy, it would be possible to get good estimates of the power required to lift the oil, the optimum depth, the pressure and the rate at which to inject gas. Furthermore, the effect of production rate and tubing sizes on these quantities can be evaluated before any design decision is made on the installation and operation of the flow string. The majority of experimental work available in the literature deals with two-component systems where individual phase flow rates in and out of the pipe remain constant. The general problem of prediction of pressure drops in multiphase flow systems is very complicated. The co-existence of numerous flow patterns of widely different geometry and mechanism, conditions of surface instability and the nature of force fields acting upon the system are among the major difficulties commonly encountered. The classical approach of fluid dynamics which would be based upon the formulation and solution of Navier-Stokes equations has been found by many investigators completely devoid of any hope of success-—not only because of inherent nonlinearities but also because of insurmountable analytical difficulties standirng in the way of setting up the boundary conditions. The presence and effect of interfacial forces on mu1tiphase flow systems further complicate the theoretical approach. For these reasons, many investigators choose to adopt semi-empirical if not purely empirical approaches in order to obtain solutions of engineering utility. A prominent practical solution has been given by Poettmann and Carpenter' in the form of an empirical correlation. In their paper, total flowing densities of fluids and solubility effects of gas in oil have been taken into account for the correlation of field data covering a wide range of operating conditions for oil wells. They treated the gas. oil and water as a single phase of combined propcrties and correlated the multiphase friction factor as a function of the product (pvd), i.e., density X velocity X diameter of the flow string. However, because the product (pvd) is dimensional while the frictior factor is dimensionless, the generality of their result's is somewhat restricted. It seems that the omission 01 viscosity effect may be one of the reasons for the scatter of data as shown in their correlation chart. The concepts of the "two-phase f factor" and the "two-phase Reynolds' number function" were recently developed and successfully applied to correlate horizontal multphase flow by Bertuzzi, Tek and Poettmann.' Recently, two new methods of correlation by Tek and Chan' have been presented on simultaneous flow of liquid and gas through vertical pipe. These two methods of correlation and the working equations in field units necessary for their application are included in this paper. The extension of the conccpt of two-phasc Reynolds' number function successfully developed for horizontal flow into vertical multiphase flow systems, development and evaluation of working charts permitting calculation of two-phase pressure gradients and

MINING and Metallurgy closed the year 1928 showing a small profit, the receipts, exclusive of the charge against members, dues for subscriptions, having been $43,067.81, and expenditures $40,925.58. In accord with the policy of the Board the budget is made each year with the purpose of balancing the accounts rather than the maximum of profit from the undertaking since it is the service the journal performs for members that justifies its existence. This service is being constantly increased. Within the year a number of changes have been made in the dress of the magazine, a new cover adopted, color more frequently used, and illustrations more generally employed. These changes seem to have been appreciated both by readers and advertisers. More space has been devoted to papers read before local sections and to the news of their activities. It is believed that this has helped materially in sustaining and increasing the interest in such meetings. The general, regional, and division meetings have also been fully reported and news of Board meetings, of the work of the various committees, of the employment service and other activities of the Institute has been spread before its members month by month. The 570 pages of reading matter printed in the course of the year constitute not only a record of what the Institute was doing but of what the most representative sections possible of the members of the mining and metallurgical professions were thinking. With 9000 members scattered around the world, occupying key positions in the industry, the Institute affords through its own journal an unsurpassed medium for broad contact and enables the readers with the minimum of expenditure of time and at no extra money expense to keep a general contact with the whole range of subjects touched by miners and metallurgists. In these days of intense specialization but rapid change such contact is particularly valuable. The more formal papers presented to the Institute are published in the Transactions, Technical Publications and the special volumes. Mining and Metallurgy carries abstracts of all papers published ,by the Institute and prints in full the shorter, less detailed papers and those which reflect work in progress rather than finished. Such papers have a news value which is supplemented by editorial comment, discussion by members and others, and the actual news of the organization itself. Without therefore attempting to fill the place of a general news sheet, it has a timeliness that gives it an immediate value much appreciated by the readers. In accord with the general policy of the Board every effort will be made constantly to improve the quality of the magazine to the full extent that its revenue will permit. Your Committee feels that, through the intelligent cooperation of the official staff in the office, Mining and Metallurgy has been improved in

Jan 1, 1929

By R. E. Head

SOME mixtures of sulphide and oxide ores from the Tintic district in Utah are of a sufficiently good grade to be shipped to the smelter without beneficiation. In mining this type of ore, however, a material tonnage of ore of a similar composition but of lower grade is obtained. It is a ques-tion of economics whether such ore should be shipped with a certainty of a small return or concentrated if that would yield a sufficiently increased return to amortize plant construction and upkeep and yield a higher rate of profit than at present. It may be assumed that the tonnage of this borderline ore is constantly increasing and that eventually it will, attain such proportions as to justify plans for milling on a relatively large scale. Under existing conditions, the producer of mixed sulphide and oxide ores is not greatly concerned about the physical characteristics of his ore or of its mineralogical complexities, since his contract with the smelter calls for payment on the basis of chemical analysis. When concentration is contemplated an entirely different picture is presented. Percentages of valuable metal content must then be con-sidered in terms of minerals, for it is in the form of minerals that recoveries are made and losses sustained. In describing the performance of a given flotation mill and reagent combination, it may be stated as a generality that a specific percentage recovery of valuable elements is made. Tech-nically, however, the concentrator is really constructed and the reagents are selected to recover the valuable minerals. These considerations must be given prominence in discussing border-line ores from the Tintic district because of their physical characteristics and mineralogical composition. Because of these peculiarities they may be justly termed complex, since their lead, silver, and copper contents are each represented by two or more minerals of different chemical composi-tion and presenting widely divergent physical properties. This paper sets forth the results of a microscopic study of a type of borderline ore from the Tintic district that is now being treated by direct smelting. A

Jan 1, 1938

By Harold A. Krueger

FACILITIES and mining operations of the National Lead Co., St. Louis Smelting and Refining Division, near Fredericktown, Mo., are situated in a famous mining area. Copper, lead, nickel, and cobalt have been mined here for more than 100 years, work having been started on a high sulphide copper outcrop in 1847. Lamotte sandstone is characterized by differential compaction on a rigorously eroded pre-Cambrian surface. The Bonneterre formation was therefore a good host for minerals not generally found in mineable quantities in these midwestern areas. Unusually complex minerals, however, make beneficiation difficult, and because of irregular ore thicknesses and elevations many engineers and operators have not attempted to mine the property. Others have tried who failed. This paper deals with economic, efficient, and competitive methods of mining these highly irregular orebodies, as compared to the open-stope, room-and-pillar methods normally used for horizontal-bedded lead deposits. For the purpose of this study it should be understood that the ore is found in two distinctly different types of occurrences, one to be designated as basin ore and the other as contact ore. Mining of basin ore is complicated by many faults, fractures, cross faults, and breaks. Contact ore is complex because it is found on flanks or slopes of pre-Cambrian knobs or highs. The dip of the mining floor for the latter type varies between 18" and 45". Occurrences of both types of ore are complicated by water courses or solution channels which carry unconsolidated shale, lime, sand, and dolomite. This material is also found between the bedding planes of the members of the Bonneterre formation. The water found where there are fractures, faults, and channels makes it very fluid and tacky, see Fig. 1, particularly after it has been blasted and handled by loading and hauling machines. Much of the ore can be wadded and thrown without dispersing. During early operations by the Buckeye Copper Co. in 1861 and the North American Lead Co. from 1900 to 1910, conventional narrow-gage railroad and side dump mine cars were used with hand shoveling. The complications of mining the contact ore, the only type attempted at this time, can be appreciated when it is realized that operators were obliged to use mules for haulage. Haulageways constructed on these slopes were of necessity similar to wagon trails or goat trails up the side of a mountain. In other words, it was merely a matter of going from side to side of the strike length of the slope, gaining a little in elevation on each shuttle trip. Production totaled only one to two tons per manshift. A few years later, about 1913, the property was purchased by combined Canadian interests known as the Missouri Cobalt Co., and the use of trolley locomotives was initiated. Between 1900 and 1928 a land agent using churn and diamond drilling methods prospected scattered sections of the area. In 1928 the first property was purchased by the present company, then operating as the St. Louis Smelting and Refining Co. Check drilling and prospecting was carried out by the company at various times between 1928 and 1939 to correlate the erratic mineralization. Much information about both types of orebodies was accumulated, but it was still questionable as to whether money should be invested to work these occurrences. In anticipation of high lead and copper prices, about the time World War II started, it was decided to develop and bring into production some of this ore. In 1942 No. 1 shaft was put down on the largest basin-type orebody and in 1943 No. 2 shaft was put down on contact-type ore. Operations were expanded when No. 3 shaft was completed in 1943, and progressed further in 1948, when National Lead Co. dewatered and opened No. 5 and 6 mines, old workings of the North American Lead Co. and the Missouri Cobalt Co. Because of the differential compaction of Lamotte sandstone over the pre-Cambrian porphyry, in some instances mineable thicknesses of basin-type ore occurred 20 to 30 ft above the sand. This is the exception rather than the rule, since most of the mineralization starts at the sand and is variable in thickness. The ore was attacked, therefore, by development drifts and crosscuts at the lowest possible elevation, where the ore immediately overlying the Lamotte sandstone could be drained and made accessible for mining. It was planned to connect to the drifts and crosscuts with raises to mine ore deposited 20 to 30 ft higher. The higher orebodies were thus mined as slusher levels. Slusher hoists were used to drag the ore into the raises, which were made into hoppers. The ore was then loaded into 32x32-in. ore cans, hauled to the shaft by battery locomotives, and hoisted by the conventional Tri-State method. The rate of efficiency was 5 to 6 tons per manshift underground. The contact-type ore was attacked in a similar way, except that the orebodies were not nearly so wide, so that they were more flexible for slusher loading into cans. This advantage was offset, however, by haulage complexities, since the railroad was constructed on steep slopes. Through experience and ingenuity, many improvements were made in mining both types of ores. The two levels, so-called, in the basin-type ore-bodies were connected as previously planned, more efficient locomotives replaced the older ones, and a

Jan 1, 1954

By J. J. Frawley, W. J. Childs

Experiments were carried out to induce grain refinement during solidification by applying vibrational energy (freq 20 kc) to small specimens of bismuth, tin, and bismuth-tin alloys. The results show that if the intensity of the applied sound -field is not great enough to fragment the growing dendrites of a pure metal, no grain refinement is observed and the pain size of the dynamically nucleated specimens is the same as the grain size of a specimen statically supercooled the same amount. Bismuth specimens did not show any grain refinement; whereas, the tin specimens did show grain refinement. This phenomenon is the result of the difference in growth habit between the bismuth and tin dendrites. The bismuth-tin alloys showed grain refinement and, in addition, the segregation pattern was changed. THE solidification process is a change in phase requiring the nucleation of the solid phase from the liquid and the growth of this solid phase at the expense of the liquid phase. Since many physical properties and also the integrity of a casting are dependent on the solidification process, understanding and controlling this process are very important.' A good example in the controlling of a cast structure using heterogeneous nucleation theory is the reduction of grain size in aluminum castings by nucleation catalysis.2 This mechanism of nucleation catalysis has been explained by Turnbull.3 Another technique for grain refinement, which has received much attention but the mechanism has not been fully understood, is to vibrate the solidifying melt. Vibrations can be applied to the melt either by vibrating the mold directly or by introducing a vibrating rod into the melt.4-13 Three mechanisms have been proposed to explain this phenomenon: 1) The mechanical fragmentation of the original dendrites that grew into the melt. These crystals or fragmented dendrites act as new growth sites. 2) The nucleation of new grains in the liquid by the generation of very high pressure pulses caused by cavitation in the liquid. 3) The remelting of the dendrite arms during the solidification process. This mechanism is operative only in alloy systems and would be enhanced by stirring or mechanical vibration. The purpose of this investigation was to determine the mechanism that will increase the number of grains when mechanical energy is introduced into a solidifying melt. APPARATUS The unit used to generate the ultrasonic vibrations was manufactured by the Redford Co., and is similar to the one used in ultrasonic soldering. Fig. 1 is a sketch of the major components used for generating ultrasonic vibrations. The crystal transducer assembly consisted of four lead zirconate ti-tanate piezoelectric crystals in an aluminum holder. An acoustical horn, which was fabricated from stainless steel, was attached to the holder by a set screw. The resonant frequency of this unit was 20,000 cycles per sec. A Pyrex crucible, 4 in. in diam and 4 in. high, was contained in a hole in the top of the horn. The piezoelectric crystals changed volume when excited by an electric signal, thereby generating a sound signal which passed through the horn. The crucible was coupled to the horn by a liquid silicone oil. The purpose of the couplant was to transmit the soundwaves from the horn to the crucible. Without the couplant, much of the sound energy would be lost. The energy transmitted was sufficient at the resonant frequency used, so that acoustical cavitation always occurred in the molten metal. The presence of acoustical cavitation was detected by the characteristic hissing sound emitted from the liquid. EXPERIMENTAL PROCEDURE The influence of ultrasonic vibration on the grain refinement of bismuth, tin, and bismuth-tin alloys was studied. These metals were chosen because of their low melting temperature and the relative ease with which they can be thermally supercooled. The following procedure was used for obtaining large amounts of supercooling. Pure bismuth (99.999+), which was received in bar form, was mechanically broken into pieces small enough to be accommodated in a 50 ml beaker. About 200 to 300 g of bismuth and a few grams of SnCl2 as a flux were placed in the 50 ml beaker and melted by induction heating. The melt was held for 20 min at

Jan 1, 1970

By Charles Legrand

The problem of mine pumping is so much affected by local conditions, and those conditions are so liable to changes during the life of a mine, that the best system to use is difficult to determine. The experience of the writer has been that, in general, for copper mines, electric pumping is most satisfactory unless the quantity of water to be pumped is great or the mine does not use electric power for any other purpose. As a rule, however, figuring on the cost of necessary power plant, the total cost of installation is greater with electric pumps than steam pumps. As the water is liable to be gritty, outside-packed plunger pumps are to be recommended, and if the water is not acid, or only slightly so, chilled cast-iron plungers pay for their extra cost very quickly in diminished cost of packing. With chilled plungers it is possible to use metallic packing instead of soft packing, if the water is not too gritty or the lift too high. In vertical pumps this packing is satisfactory for lifts up to 400 ft., in the experience of the writer, and may be found satisfactory for higher lifts. For water slightly acid, cement-lined pump bodies have given good satisfaction. For acid water, both plungers and puhp bodies should be made of acid-resisting bronze. For high lifts, especially with gritty water, a satisfactory pump valve is difficult to find. To reduce the unbalanced pressure on the valve at time of opening it is advisable to have narrow seats; this, however, brings high pressures on the seats when the valve is closed. On large valves for lifts of 600 to 1,000 ft. we have used leather, hard rubber, vulcanized fiber, and soft brass; for clear water the latter has given best satisfaction. The difficulties due to grit make it advisable to have large sumps where water can settle, and if possible, to have two of them so that they can be cleaned alternately. At the mines of the Old Dominion Copper Mining & Smelting Co., Globe, it was found that a small air ejector discharging into a mine car provides a very convenient way to clean mud and sand from a sump.

Jan 1, 1916

By Charles H. Grant

Some of the limiting factors relative to explosive crushing of rock and ways to overcome a few of these problems are presented. Relationships between borehole diameters, bench heights, and spacings, along with a review of the influence geometry has on energy as these are changed, are discussed. Efficiency in use of explosives and the decay of energy as it moves through rock and is absorbed and dissipated, is described, along with fragmentation as a function of spacings and energy zoning, etc. Communications are one of the major problems encountered. In an effort to provide a better understanding of the use of explosives, it is necessary to take a little different view of what explosives are, how to look at them as tools to fragment rock, and some of the problems encountered in doing so. First, take the explosive: although there are many factors involved, consider these as being reduced to only two — shock-strain imparted to the rock by the high early development of energy, and the gas effect which is a combination of heat, moles of gas formed, rate of formation of these gases which develop pressures, etc. First, consider shock energy by itself and assume there is no gas effect in the reaction. Fig. 1 illustrates a block or cube of rock, in the center of which is detonated an explosive charge which is 100% shock energy. Tensile slabbing would be seen on the surface and probably the cube of rock would generally hang together even though microcracks were formed. If the situation is reversed and an explosive whch has no shock energy and only gas effect (Fig. 2) is considered, the cube of rock would act as a pressure vessel and contain the pressure from the gas effect until it exceeded the rock-vessel strength; then the rock would break in a few large pieces. If these two kinds of energy are put together and the area of shock-strain around the explosive (Fig. 3) is considered, the two energies will be seen working together to furnish broken rock. The gas effect applies pressure to the microcracks formed from the shock energy to weaken the rock-pressure vessel and propagate these cracks to break the rock apart. It not only will be broken more finely, but will break apart at a lower pressure than the gaseffect case, since the shock energy has first weakened the rock vessel. Although tensile spalling from the shock-strain imparts momentum to the rock, the main source of displacement comes from the gas effect. The term "rock" is being used to mean any material to be blasted. These energies are absorbed by the rock in different ways. First, classify rock into two main categories: "elastic" and "plastic-acting." Elastic rock should be thought of as rock which can transmit a shock wave and is high in compressive strength, such as granite or quartzite. Since this elastic rock transmits a shock wave well, it makes good use of the shock energy from the explosive-forming cracks, etc., for the gas effect to work on. Plastic-acting rocks are rock masses which are relatively low in compressive strength and absorb shock energy at a much faster rate, thereby making poor use of the shock energy by not developing as extensive a cracked zone for the gas effect to work on. Rocks of this type are generally softer materials such as some limestones, sandstones, and porphyries. For the most part, the shockenergy part of the explosive reaction is wasted in plastic-acting rock, leaving most of the work to the gas effect. Since the ratio of gas effect to shock energy is different in different explosives, it is easy to understand why some explosives perform well in elastic rock and poorly in plastic-acting rock, and vice versa. Some of the most difficult blasting situations arise when mixtures of plastic-acting and elastic rock are encountered (Fig. 4). Fig. 4 shows an example of granite boulders cemented together with something like a decomposed quartz monzonite which is plastic-acting. The elastic granite boulders will transmit the shock-strain within itself, but when this shock tries to move through the monzonite to the next boulder, its intensity is absorbed by the monzonite and little shock-strain is placed on the adjoining boulder. In addition to this loss by absorbtion, shock reflection at the surface of the boulder will effect tensile spalling. The net effect is poor breakage of the boulders which do not have drillholes in them as they simply will be popped out with the muck. The same is true (Fig. 5) when layers and joints make

Jan 1, 1970

By Howard N. Eavenson

The information contained in the following paper was collected at the request of the U. S. Coal Commission, and is published with the permission of that body and of the various companies furnishing the data. For obvious reasons, the names of the companies are not given. No data were obtained from states south of Virginia or west of the Mississippi River. The data about the amount of labor, in man-hours, required in producing a ton of bituminous coal have been collected with the idea of showing what is being done at some well-managed plants, and not to show the average amount required by all mines, which undoubtedly is considerably higher than the average of the figures shown.* Almost all of the figures were supplied by the various companies in reply to a questionnaire; when they were obtained from other sources the company was asked to verify them. On account of the amount of work required, the data were only requested for one or two months for each plant, and the figures represent in each case a month when the car supply was good and the work was practically steady. In the case of most of the West Virginia and Kentucky mines, these conditions were best met in May and June, 1922. The mines for which the figures are given are arranged by states and as to whether the mine operates under union or non-union or open-shop conditions. The union mines listed are generally considered to be as well-managed as are the non-union ones. The production per month in a few cases includes the amount of slate which is loaded and hauled out of the mine, as of course this requires nearly as much labor per ton as does the coal. These cases are noted. The number of days worked includes only the total time in which the tipple operated; not the number of days on which the mines operated. This makes the output per day appear slightly higher than it should be in

Jan 1, 1924

By O. L. Kowalke

THE measurement and control of temperatures have assumed positions of great importance in many industries. The manufacturers of byproduct coke and carbureted water gas find that proper temperature control helps to produce a better product and economizes in the use of raw materials. In the manufacture of glass, enameled ware, brass, and high-temperature refractories, temperature control is now regarded as being coordinate in importance with the control of materials used. To control such processes as malleablizing cast iron, and hardening, tempering, and annealing of steel in a manner to meet exacting market requirements has, within recent years, involved the installation of large and expensive pyrometer equipments. In many of these installations, it was necessary not merely to measure but also to record the temperatures over a period of time and thus obtain a record of the entire heat treatment and an effective check on the workmen in charge. In view of the importance of temperature measurement and control in such a wide variety of industries and the necessity for proper supervision of the installation and operation of the outfits, the following questions may be pertinent: What instruction is offered by the engineering colleges and what departments in the colleges are responsible therefor? The latest available catalogs of ten prominent engineering colleges east of the Mississippi River showed courses in high-temperature measurements given by the departments of physics. These courses, in general, were described as comprising classroom and laboratory instruction in the theory of high-temperature measurements, together with exercises in the calibration of the various devices used. In some cases it was stated that consideration would be given, in the courses, to the practical applications in the industries. In only one. college was the course required of all engineering students; in most colleges it was optional; in a few colleges, it was required only of certain groups. In colleges offering a course in metallurgical engineering, instruction in pyrometry was always given in connection with metallurgical laboratory work. The students in ceramic,

Jan 8, 1919

By Howard Scott

Invar is the preeminent low-expansion metal by virtue of the fact that it can be prepared with a zero coefficient of expansion at atmospheric temperature. This fact suggests that there is little room for improvement in the expansion properties of the low-expansion nickel steels. The inference is true, however, only so far as the expansion at and near atmospheric temperature is concerned, because the expansivity of invar starts to increase rapidly on heating above 100" C. and soon reaches the value of copper. Guillaumel met this situation by increasing the nickel content above that of invar. By that expedient, alloys having low expansivity under higher temperatures were obtained, but not without a large increase in minimum expansivity. The increase in minimum expansivity with increasing nickel content severely limits the technical applications of these alloys at high temperatures. Prospects of improving the expansion characteristics of the nickel steels is offered by alloying. Search for an advantageous alloying addition by analogy with other alloy systems, however, is not productive because the low-expansion characteristic is unique with that system. The rule of mixtures usually gives a fair value of the expansivity of other solid-solution alloys, but in the iron-nickel systems gives a value of 18 X 10-6 per deg. C. whereas the actual value is 1 X 10-6 per deg. C. Apparently suitable additions are not to be deduced from such ingenuous considerations. Recognition of the fact that the temperature range of low expansivity in nickel steels is terminated with loss of magnetism affords a more promising basis for the selection of an advantageous element. One may expect from that fact that additions of nonmagnetic elements to the iron-nickel alloys are detrimental to the low-expansion characteristic. Indeed, carbon, manganese, silicon, copper and chromium are detrimental to the expansion properties and no nonmagnetic element is reported to be beneficial. From the same viewpoint, the addition of a magnetic metal offers prospects of improvement. As two of the three ferromagnetic elements are already present in the

Jan 1, 1930