Search Documents

By J. H. Henderson, L. A. Wilson, R. L. Gergins, R. J. Wygal, D. W. Reed

This paper presents a method of predicting the production history of an underground combustion recovery process. A rigorous solution of the thermodynamics and hydrodynamics involved is beyond the scope of this report. However, a practical scheme to appraise combustion recovery performance has been Worked out. By prudent assumptions, regarding the attainment of steady-state conditions, a trial-and-error solution, which satisfies both material balance and three-phase relative permeability requirements has been evolved and tested. As a combustion zone moves through a formation the interstitial water, the water of combustion and a portion of the oil wil1 be vaporized. These vapors will move downstream to a cooler region of the formation where they will condense. Part of the remaining oil will be displaced by the imposed gas drive and what remains behind will be consumed as fuel. The fluids will distribute themselves downstrean? in a manner which will satisfy the three-phase relative permeability characteristics of the formation. Three distinct zones will exist ahead of the combustion zone: (I) a zone termed a water bank which contains three mobile phases, oil, water and gas; (2) a region containing two mobile phases, oil and gas, called the oil bank; and (3) a zone having the fluid saturution distribution which existed prior to combustion. The mobile water will impose a water flood on the oil in the region containing three flowing phases. The process can be visualized as a simultaneous water .flood and combustion-supported gas drive. It is possible to estimate the saturation distributions in the water bank and oil bank as well as the production history for any combustion temperuture if the porosity, three-phase relative permeability characteristics, oil viscosity and initial saturations are known. This has been done for injection pressures ranging from I to 100 atm, oil viscosities of 10 to 1,000 cp and porosities from 20 to 40 per cent. Several of these calculations have been checked in the laboratory, with the result indicating rather good agreement between the predicted and observed production histories. The analytical and experimental techniques are described and the comparison of predicted and observed performance presented. INTRODUCTION Considerable research by the oil industry during the past 10 years has been directed toward the thermal recovery of crude oil. Of all schemes considered, the one receiving the most attention is in situ combustion. This is a process in which part of the oil is actually burned within the reservoir rock. The uniqueness of the process lies in its potential. Theoretically, this potential generates from the following: (1) it may open the door to vast reserves previously not economically producible, (2) it may induce increased production rates where low rates are now realized and (3) it may give high over-all recovery efficiency. The general idea of the process has received considerable attention in the literature '-' and the following brief description is intended for orientation only. In situ combustion can be visualized by considering a linear system, one end of which represents the injection well and the other the producing well. The formation at the inlet end is raised to ignition temperature by placing a gas or electric heater at the face of the formation or by the ignition of thermite, charcoal or similar material. While heating, the water and part of the oil in the heated region is vaporized and moved out into the reservoir by the injection of gas containing oxygen. In addition, part of the oil is displaced as liquid by the imposed gas drive. The oil not displaced is modified to an immobile, coke-like material (hereafter referred to as coke) by the high temperatures existing immediately ahead of the combustion zone. This coke is used as fuel, and the combustion front advances through the formation at a temperature which is probably in excess of 800°F. As the combustion front advancek it will drive ahead all interstitial oil not rendered immobile and all interstitial water plus the water formed by the combustion of hydrogen. As a result the sand behind the combustion zone is freed of all oil and water. Although the general description of the process has been outlined in the literature, there has been no consideration of the behavior of the fluids moving downstream from the combustion front. It is the purpose of this paper to present a technique

TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-To a Board of Directors keeping in as close touch with all of the affairs under their care as do the Directors of the A. I. M. E., through their monthly meetings, a report of the year's progress is almost superfluous. ' To the members who read the monthly reports of the Board Meetings and of the various activities of the Institute as published each month, a yearly report cannot carry much fresh information; yet for both it may be well, as is the custom, to glance over the field of our activities during the past year, and to make an estimate for the year to come. The beginning of 1924 was not propitious for the members of the mining profession, though tonnage production for 1923 had been high and the gross value higher than for several years. The margin of profit had been narrow, prospecting and development were limited, and many of our members were unemployed or were working in other industries. Toward the end of the year, higher metal prices were in sight. Old-time optimism began to grow, and it now brightens the outlook for 1925. An excellent barometer of the prosperity of the industry, and that of the Institute, for they go hand in hand, is the work of our Employment Bureau. During the past few months, the percentage of our members for whom openings have been found has been increasing to a marked extent, and many members who had fallen in arrears are placing themselves in good standing. The number of new members joining has remained about as it was in 1922 and 1923. The Directors have reason to congratulate themselves on the interest maintained during a dull period, for it is not humanly possible to take a keen interest in the technology of an industry when our hands and minds are not actively engaged in it Now, with a much brighter outlook, we can look forward to a year of increasing prosperity for the industry and for the Institute.

Jan 1, 1925

By Leslie W. Austin

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, periclase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks: These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. 1-The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2-As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3-If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4-Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spall being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1952

United Engineering Trustees, Inc James L Head, '55, E C Meagher, '56, Gail F Moul¬ton, '57 Advisory Committee to Real Estate Committee Cleveland Dodge, Herbert Hoover, Paul D Merica The Engineering Foundation W M Peirce, '56, A M Gaudin, '58 Research Procedure Committee A M Gaudin, March '54 Engineering Societies Library Board Frank T Sisco, '54, E M Wise, '56, James L Head, ex officio Engineering Societies Personnel Service Board of Directors E J Kennedy, Jr, E H Robie

Jan 1, 1954

By R. E. Head

Some mixtures of sulphide and oxide ores from the Tintic district in Utah are of a sufficiently good grade to be shipped to the smelter without beneficiation. In mining this type of ore, however, a material tonnage of ore of a similar composition but of lower grade is obtained. It is a question of economics whether such ore should be shipped with a certainty of a small return or concentrated if that would yield a sufficiently increased return to amortize plant construction and upkeep and yield a higher rate of profit than at present. It may be assumed that the tonnage of this borderline ore is constantly increasing and that eventually it will attain such proportions as to justify plans for milling on a relatively large scale. Under existing conditions, the producer of mixed sulphide and oxide ores is not greatly concerned about the physical characteristics of his ore or of its mineralogical complexities, since his contract with the smelter calls for payment on the basis of chemical analysis. When concentration is contemplated an entirely different picture is presented. Percentages of valuable metal content must then be con-sidered in terms of minerals, for it is in the form of minerals that recoveries are made and losses sustained. In describing the performance of a given flotation mill and reagent combination, it may be stated as a generality that a specific percentage recovery of valuable elements is made. Technically, however, the concentrator is really constructed and the reagents are selected to recover the valuable minerals. These considerations must be given prominence in discussing borderline ores from the Tintic district because of their physical characteristics and mineralogical composition. Because of these peculiarities they may be justly termed complex, since their lead, silver, and copper contents are each represented by two or more minerals of different chemical composition and presenting widely divergent physical properties. This paper sets forth the results of a microscopic study of a type of borderline ore from the Tintic district that is now being treated by direct smelting. A

Jan 1, 1939

By R. E. Head

Some mixtures of sulphide and oxide ores from the Tintic district in Utah are of a sufficiently good grade to be shipped to the smelter without beneficiation. In mining this type of ore, however, a material tonnage of ore of a similar composition but of lower grade is obtained. It is a question of economics whether such ore should be shipped with a certainty of a small return or concentrated if that would yield a sufficiently increased return to amortize plant construction and upkeep and yield a higher rate of profit than at present. It may be assumed that the tonnage of this borderline ore is constantly increasing and that eventually it will attain such proportions as to justify plans for milling on a relatively large scale. Under existing conditions, the producer of mixed sulphide and oxide ores is not greatly concerned about the physical characteristics of his ore or of its mineralogical complexities, since his contract with the smelter calls for payment on the basis of chemical analysis. When concentration is contemplated an entirely different picture is presented. Percentages of valuable metal content must then be con-sidered in terms of minerals, for it is in the form of minerals that recoveries are made and losses sustained. In describing the performance of a given flotation mill and reagent combination, it may be stated as a generality that a specific percentage recovery of valuable elements is made. Technically, however, the concentrator is really constructed and the reagents are selected to recover the valuable minerals. These considerations must be given prominence in discussing borderline ores from the Tintic district because of their physical characteristics and mineralogical composition. Because of these peculiarities they may be justly termed complex, since their lead, silver, and copper contents are each represented by two or more minerals of different chemical composition and presenting widely divergent physical properties. This paper sets forth the results of a microscopic study of a type of borderline ore from the Tintic district that is now being treated by direct smelting. A

Jan 1, 1939

By N. O. Johnson, J. Boyer, D. H. Sargent, R. B. Frahme

Although the Western bentonite industry has grown rapidly, it is facing major challenges to sustained growth. The fundamental penalty of costly overland transportation to both domestic markets and to US seaports is of increasing importance; as both substitute materials and foreign bentonites present more formidable competition in the historic market areas of drilling muds, foundry sands, and iron ore pelletizing; and as foreign demand grows more rapidly than domestic demand. The Western bentonite industry is facing these challenges by altering its transportation patterns, by upgrading of products, and by emphasizing customer service and stringent quality control.

Jan 1, 1980

By J. E. Sherborne, P. H. Jones, E. C. Babson

A study of the Chapman zone in the Richfield field, Orange County, California, indicates that the quantity of oil recovered by present methods will be only a small portion of the oil originally in place. Since the volume of residual oil is believed to be of large magnitude, an experimental water-flooding operation has been initiated in order to determine whether water-flooding offers promise as an economical method of recovering some of this residual oil. A single injection well was drilled between old producing wells, and a water-treating plant using alum flocculation and chlorination was designed and built. Water has been injected into the input well for six months at rates in excess of 100 bbl. per day. Production from one of the neighboring wells has increased materially, the oil production having risen from 7 to 30 bbl. and the water From I to 40 bbl. per day. While definite conclusions regarding the economic success of water-flooding in the Chapman zone are not justified at this time, it has been demonstrated that water can be injected into the zone on a sustained basis and that this water will displace appreciable quantities of oil from the sand. Introduction As a result of an investigation of subsurface conditions in the Chapman zone of the Richfield field, it was concluded that ultimate oil recovery from this zone would probably be low and that natural water encroachment was so localized as to be of little importance from a recovery stand- point. Furthermore, it was found that in many portions of the zone the wells were approaching an unprofitable level of production. When these data were presented to the management of the Union Oil Co.; their reaction was that an attempt should be made to develop methods of recovering at least a portion of the large quantity of oil remaining in this zone. After some investigation, it was decided that wafer-flooding offered the most likely means of accomplishing this end, but reservoir conditions in the Chapman zone differ so widely from those encountered in any of the flooding projects described in the literature that it was difficult to evaluate the probability of success. Despite encouraging results from laboratory tests, it was not even certain that water would displace an appreciable volume of oil from the Chapman sand under reservoir conditions. Therefore, it was decided to initiate a small-scale project, for two purposes: first, to determine whether water would displace oil from the Chapmall sand and, second, to obtain information and experience for future operations if water-flooding appeared to be a promising method of secondary recovery. Reservoir Data The Chapman zone is the upper of the two producing zones in the Richfield field, being found at depths from 3000 to 3700 fi.. The productive portion of the zolle consists of a large irregularly shaped sand body, which is more than 400 ft. thick at the top of the structure. As the margin of the field is approached, the sand is replaced

Jan 1, 1945

By C. E. Turner, J. R. Elenbaas, R. D. Grimm, J. A. Vary, D. L. Katz

A technique is presented by which well samples and core plugs of dolomite formations are classified by microscopic examination into seven different porosity grades. Quantitative values of porosity and permeability are determined for each grade by a statistical correlation of the core plug test data with the porosity grading system. These quantitative values are applied directly to the grades exhibited in the well samples for the purpose of estimating the reservoir void space for wells that were not cored. The procedure is described for estimating the gas reserves per unit area lor the South Hugoton gas field. but a reserve estimate for the field is not given. INTRODUCTION The miscroscopic examination of well sample; and the graphic recording of their lithologic qualities and other distinguishing characteristics of various geologic formations drilled is both a science and an art of long standing and wide application. Usually the primary objective of a geologist who "sits on the well" and examines the samples are: to identify the formation being drilled, determine the total depth, casing point. and completion interval. In most cases the porosity is described. if done at all, in general terms. such as: trace, scattered, fine, poor, fair, medium. good, excellent, or in some other relative terms. In fields where various geologists have examined samples and recorded observations on many wells considerable variations in lithologic terms and porosity descriptions occur unless there is primary effort to establish uniformity of logging observations and standards of recording observable porosity. When an estimate of the pore volume of a reservoir is made a geologic concept of the processes that control the magnitudes of porosity and permeability is developed by microscopic examination of well samples. The characeristics and appearances are then mentally related to rather general quantitative units of porosity based on physical core data from the same reservoir or on such data or experience in other reservoirs that have similar qualities. The reliability of such estimates depends largely on the variations of the lithology of the formations, the geometric properties of its void system. the extent of comparisons of sample appearances with porosity data, as well as the uniform recording of all relevant characteristics. This statement is particularly significant for dolo-mitized limestone formations of substantial thicknesses and heterogeneity such as the Permian Dolomites of the Hugoton gas field. Jn this field, as well as in most of the Permian Dolomite fields, the producing formations are of relatively great thicknesses in which the porosity and permeability of the reservoir varies substantially in all directions, depending on the crystalline structure. degree and kind of impurities, kind of fossils anti cementation thereof, degree of dissolution. and fracturing. The variations of the lithologic texture of the dolomites and post deposition alterations have resulted in porosities and permeabilities of such magnitudes that only a part of the gross thickness can be counted as "pay." At the time of this study insufficient gas production had been experienced to apply the pressure decline production method in the South Hugoton Field and the electric logs are not definitive enough. The problem of estimating gas reserves in the south part of the Hugoton Field is primarily one of determining the pay thickness and porosity from well samples and core data. The area studied embraced all that part of the field lying south of an east-west line through Guvmon, Okla., anti containing approximately 1.000,000 acres. This paper describes a technique of correlation of physical core data with well samples so that quantitative values of pay thickness, porosity. Permeability, and connate water may be assigned to well samples that are representative of a given interval, and thereby permitting the estimation of gas reserves lor a given unit area. The procedure was developed by a uniform microscopic qualitative porosity grading of the dolo. mite core plugs.. and relating these grades to the respective physical core data on a statistical basis The well sample-were also graded in a Similar manner in order that the quantitative values established lor the core plugs could be applied to the well Sample for wells that were not cored. GRADING OF DOLOMITE A group of experienced geologists was given the assignment of examining the samples on all wells in South Hugoton in order that they could log their observations in a uniform and standardized manner and grade the observed porosity so that it could be related quantitatively to the core data. The group initiated the study 011 chips from cores which bad been tested for porosity and permeability. This study continued until all of the geologists developed a common knowledge of lithologic terms and of the characteristic appearances of the samples and their relations to measured porosity. The characteristic appearances of the dolomite samples under twelve-power magnification as related to their qualitative porosities afforded a classification of the dolomite into :even grades of porosity, ranging from dolomite of no-visible porosity under twelve-power magnification to dolomite of excellent porosity. The assigned grade for a specific 10-ft interval is a weighted average of all visible grades of porosity exhibited by the cuttings representing that interval. The porosity characteristics were recorded by a color graph adjacent to the lithology column in conjunction with a numerical system for further definition of relative porosity as shown in Fig. 1. The three vertical lines to the right of the lithology column each represent 33 1/3 per cent. which lines were used to record the percentage of the samples, for any particular interval. that showed porosity under the microscope. The colors were used to denote actual pore size. i.e., orange. blue and I-ed for pore diameter of one-fourth or less. one-fourth to one-Ilalf. and greater than one-half millimeter, respectively. The area colored 1)). one or more colors represents the percentages of the samples exhibiting pores of the respective size or sizes. The numerals from one to six inclusive shown on the log in

Jan 1, 1952

By Julien F. Phillips, Donald E. Garrett

The production of soda ash from natural sources is one of the United States' oldest industries. The London Company, which financed the settlement of Jamestown, in the fall of 1608 exported in its first cargo from Virginia " . . . trials of pitch, tar, glass, frankincense, and soap-ashes."1 This last product, a crude mixture of sodium and potassium carbonates obtained by the burning of wood in iron pots, was the commercial soda ash of its day, used in the infant soap, glass, and bleaching industries. Besides having a good cash value, its production helped to clear the land, and it was a compact, easily shipped commodity. The extra high potassium content of these American "pot-ashes" gave them an added market as a fertilizer, a field that they dominated until the opening of the Strassfurt deposits in 1860. This form of natural soda ash disappeared forever from commercial importance with the introduction of the Le Blanc process (1791), and later the Solvay process for manufacturing soda ash. The Solvay process was rapidly accepted in the United States, and has accounted for most of the country's soda ash production since 1884. It was not until the western part of the country began to be developed that natural soda ash was again produced. A number of lakes, playas, and springs west of the Rocky Mountains were found to be rich in this mineral, and climatic conditions were ideal for its easy recovery by solar evaporation. The production of natural soda ash from these deposits has become a steadily growing industry in the United States. Production A summary of the production and value of natural sodium carbonates in the United States is presented in Table 1. Prior to 1927 the principal output came from several different companies at Owens Lake, California. Then production at Searles Lake, California, began to [ ] increase until it became the most important source. In 1948 the sale of crude trona from Green River, Wyoming, commenced and since that time production from these latter two areas has been about equal. Table 2 lists the four

Jan 1, 1960

By L. D. Lamont, W. C. Muehlhof

Throughout the anthracite industry's history, the problem of handling and disposing of refuse material has been one of major importance. In the early days of the industry's activities, only the large sizes of anthracite were satisfactory for market requirements and the smaller sizes were deposited as refuse. As time went by, more efficient coal-burning equipment was developed and a market demand was created for the finer sizes of coal. This demand made it possible to recover marketable coal from banks deposited as refuse in the earlier days of mining. The same condition holds good today and we can see a definite trend toward the objective of utilizing the No. 4 and No. 5 buckwheat sizes. Under present conditions, we know that a limited market exists for No. 4 and 5 buckwheat; we know that the finer sizes of anthracite can be burned as pulverized fuel; we know that these fine sizes can be processed and sold as briquettes, and we also know that the heat content of these fine sizes of coal is comparable with that of the sizes now merchandized. Therefore, it should be the objective of the industry to conserve these fine sizes of coal in such manner that if and when processing facilities are developed, and market demands exist, the material can be salvaged and made available to meet these demands. From the standpoint of economical future reclamation, the ideal method of disposing of refuse containing the finer sizes of coal is to deposit it in banks separate and apart from other breaker refuse. By this procedure, the minimum amount of material will be processed in future salvage operations to recover the No. 4 and No. 5 buckwheat sizes. Many collieries in the anthracite region are operated under leases that have a specific term. These lease agreements provide that, upon expiration of the lease by term, exhaustion or otherwise, the ownership of the refuse material reverts to the lessor. Therefore, a question was raised in the minds of these operators: Why should I assume the expense of such procedure when I have no assurance that I will benefit by the future processing and sale of these fine sizes? Under present conditions, the answer to this question is not one of choice but of necessity, as restrictions imposed by legislation make it mandatory on operators of preparation plants to take necessary steps to properly treat silt-laden waters before permitting them to enter the streams. By reason of these restrictions, the disposal of fine sizes becomes a secondary rather than a primary operating consideration, and the procedure for disposing of this refuse becomes a matter of choice governed principally by topographical and geographical conditions. Methods of Handling Refuse There are three principal methods of handling and disposing of fine-size refuse; namely:

Jan 1, 1947

By W. C. Muehlhof, L. D. Lamont

Throughout the anthracite industry's history, the problem of handling and disposing of refuse material has been one of major importance. In the early days of the industry's activities, only the large sizes of anthracite were satisfactory for market requirements and the smaller sizes were deposited as refuse. As time went by, more efficient coal-burning equipment was developed and a market demand was created for the finer sizes of coal. This demand made it possible to recover marketable coal from banks deposited as refuse in the earlier days of mining. The same condition holds good today and we can see a definite trend toward the objective of utilizing the No. 4 and No. 5 buckwheat sizes. Under present conditions, we know that a limited market exists for No. 4 and 5 buckwheat; we know that the finer sizes of anthracite can be burned as pulverized fuel; we know that these fine sizes can be processed and sold as briquettes, and we also know that the heat content of these fine sizes of coal is comparable with that of the sizes now merchandized. Therefore, it should be the objective of the industry to conserve these fine sizes of coal in such manner that if and when processing facilities are developed, and market demands exist, the material can be salvaged and made available to meet these demands. From the standpoint of economical future reclamation, the ideal method of disposing of refuse containing the finer sizes of coal is to deposit it in banks separate and apart from other breaker refuse. By this procedure, the minimum amount of material will be processed in future salvage operations to recover the No. 4 and No. 5 buckwheat sizes. Many collieries in the anthracite region are operated under leases that have a specific term. These lease agreements provide that, upon expiration of the lease by term, exhaustion or otherwise, the ownership of the refuse material reverts to the lessor. Therefore, a question was raised in the minds of these operators: Why should I assume the expense of such procedure when I have no assurance that I will benefit by the future processing and sale of these fine sizes? Under present conditions, the answer to this question is not one of choice but of necessity, as restrictions imposed by legislation make it mandatory on operators of preparation plants to take necessary steps to properly treat silt-laden waters before permitting them to enter the streams. By reason of these restrictions, the disposal of fine sizes becomes a secondary rather than a primary operating consideration, and the procedure for disposing of this refuse becomes a matter of choice governed principally by topographical and geographical conditions. Methods of Handling Refuse There are three principal methods of handling and disposing of fine-size refuse; namely:

Jan 1, 1947

The Bougainville ore body was discovered in 1964 by a partnership of Conzinc Rio Tinto of Australia and New Broken Hill Consolidated Limited. The ore body is a porphyry copper in a fine-grained quartz diorite, which intrudes andesite volcanics and is located at an elevation of about 2, 000 ft in the Crown Prince Range of Bougainville in the Solomon Islands. Mineralization is predominantly chalcopyrite with some bornite and some gold and silver present. Rainfall in the area amounts to 200 in. (5. 08 m) per year. An active volcano is situated only 24 miles (38.4 km) from the mine, and all structures were designed to resist seismic shocks. An interesting and unique feature of the Bougainville operation was that the overburden was stripped with hydraulic monitors. Bougainville Copper, at 90,000 tpd, is the largest copper concentrator to be designed and constructed at one time; and besides the twin 54 in. by 74 in. Allis-Chalmers gyratories, it features seven 7 ft (2. 13 m) standard and fourteen 7 ft shorthead crushers, in addition to nine 18 ft diameter by 21 ft long (5. 5 m by 6. 4 m), 4250 hp, single -stage ball mills. During the design stage of the Bougainville primary crushing plant, several alternates were studied because the ore was expected to break with the production of large amounts of small-sized particles but with a minimum of fines. These alternates included two 54 in. by 74 in. gyratories with grizzlies, two 60 in. by 89 in. gyratories, and one 72 in. by 96 in. gyratory, the latter two installations without grizzlies. The two 54 in. units with grizzlies were finally selected as giving good reliability and the ability to handle the large amounts of small material in the feed. As originally installed, grizzly bars were set at 8 in. (203 mm); but, in an effort to perform more interparticle crushing in the primary and less rock-on-steel crushing in the secondaries and tertiaries, a test is underway (1976) to determine the effect of using 6 in. (152 mm) grizzly spacings (see write -up on Anaconda's crusher at Butte). The Bougainville ore is mined with 17 cu yd (13 cu m) shovels and hauled in 105, 170, and 210 st trucks to the crushers, which are equipped for two-side dumping. Up to 40% of the ore passes the grizzlies, which are equipped with splitters; and additional horizontal splitter bars are located directly above the spider caps. Because of the grizzlies, the crushers are supported by unique U-shaped enclosures, which are in turn supported by the end and center walls of the installation.

Jan 1, 1978

[Aase, Qlenn D., (Junior Member '40) Jr. Met.. American Smelt. & Refin. Co., Selby. Calif. Abadie, Henry G., (Junior Member '43) Petr. Engr.. Avenal, Calif. Abbott, Clarence E., (Member '04) Civil En=.. V.P.. Tennessee Coal. Iron & R.R. Co., 1542 Brown biarx Bldg.. Birminpham, Aln. Abbott. Fred E., Jr., (Member '44) Petr. Engr., C/O Arabian Anierican Oil Co.. A.P.O. 816. c/o Postmaster, New York, N. Y. Abel, Raymond L., (Member '28) Chem. Engr.. C. O., Pittsburgh Chem. Warfare Procurenlent Dist.. American Bank Bldg., Pittsburph. Pa. Abel, Walter D., (Member '32) Min. Engr.. Supvr. Engr.. RFC, Los Angeles, Calif.]

Jan 1, 1946

By H Pray, H. W. Russell, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By H. W. Russell, H Pray, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By H. W. Russell, Paul D. MILLER

IT is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranular corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels have been ably discussed by Bain and co-workers1-3 and by other investigators.4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a. mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measurements, measurement of the degree of cracking produced on bending over a mandrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A-10 11 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. EXPERIMENTAL METHOD A small area of the steel under test is subjected to an anodic treatment in a cell that can be clamped onto a sample or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8-in. diameter. The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By Norman F. Schulz, Emert W. Lindroos, Strathmore R. B. Cooke

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (-—CH,CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder" has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate—potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality. of the preparation of the aminoethyl starch: "Three hundred and sixty grams of powdered unmodified corn starch was slurried in 3 liters of water and stirred during gelatinization. Eighty-six grams of ethylenimine was added slowly during reflux which was continued for 4 hr. The yellow solution set to a gel upon cooling. This was broken up and neutralized with HC1. The thick paste was dried on hot rolls. Adsorbed polyethylenimine and salts were removed from the yellowish products by washing first with acidified aqueous '60 per cent' alcohol. The white product contained nitrogen corresponding to about one aminoethoxy group per ten glucose residues." Only laboratory samples of this starch derivative have been prepared. The starch reagents for use in flocculation, flotation, and adsorption tests were made up by dispersing the appropriate quantities of air-dry starch in cold water, adding boiling water, and heating for 30 min at 120°C under pressure. When used ip adsorption tests, the starch solutions first were cleared of insoluble matter by centrifugation.

Jan 1, 1953

By Strathmore R. B. Cooke, Emert W. Lindroos, Norman F. Schulz

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (-—CH,CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder" has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate—potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality. of the preparation of the aminoethyl starch: "Three hundred and sixty grams of powdered unmodified corn starch was slurried in 3 liters of water and stirred during gelatinization. Eighty-six grams of ethylenimine was added slowly during reflux which was continued for 4 hr. The yellow solution set to a gel upon cooling. This was broken up and neutralized with HC1. The thick paste was dried on hot rolls. Adsorbed polyethylenimine and salts were removed from the yellowish products by washing first with acidified aqueous '60 per cent' alcohol. The white product contained nitrogen corresponding to about one aminoethoxy group per ten glucose residues." Only laboratory samples of this starch derivative have been prepared. The starch reagents for use in flocculation, flotation, and adsorption tests were made up by dispersing the appropriate quantities of air-dry starch in cold water, adding boiling water, and heating for 30 min at 120°C under pressure. When used ip adsorption tests, the starch solutions first were cleared of insoluble matter by centrifugation.

Jan 1, 1953

AT THE beginning of May the German government offered to the French and Belgians the payment of 30 billion .gold marks as indemnity, accom-panied by rather involved terms, among which was the ability of the Germans to finance the foreign loan. This offer was promptly and summarily refused by the French and Belgians. Since then there have been more palavers between the two parties, while the occupation of the Ruhr continued without especial incident, except some socialist riots and workmen's strikes. The renewed conference between the Allies and the Turks at Lausanne continued, without apparently getting anywhere. The Turks demanded an indemnity from the Greeks, which the latter refused to pay, threatening a resumption of hostilities rather than to do so. A. Bonar Law, the British premier, resigned his office soon after the middle of May, owing to poor health. The King appointed Stanley Baldwin as his successor. This. Attainment to the premiership of Great Britain by a business man is a noteworthy event. It is, moreover, to be remarked that Mr. Baldwin is personally acquainted with America and is well known to be a friend to Americans. The Irish rebellion came to an end. Economically there was some improvement in the situation in Great Britain during May, which was reflected in diminution in the number of unemployed. Nevertheless the aggregate of the unemployed in Great Britain continues at a very high figure. In Germany there has been an increase in the number of unemployed ever since the French occupation of the Ruhr, which naturally has been choking German industry. Previous to this the percentage of unemploy-ment among German workers had been low ever since the Armistice. A noteworthy domestic event was the non-stop flight of an airplane, May 2-3, bearing two aviators from New York to San Diego, California, in about 27 hours.

Jan 5, 1923