Search Documents

By D. G. Russell

A simple method has been developed with which flowing bottom-hole pressure data from two-rate flow tests in oil or gas wells can be analyzed to estimate the formation permeability, skin factor and average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized producing rate of the well is changed to another, higher or lower, rate. The new method yields the same information as a conventional pressure buildup analysis, but eliminates the need for closing in the well. The analysis of a two-rate flow test is of the same degree of difficulty and requires about the same engineering time for application as a conventional pressure buildup analysrs. The extended closed-in periods experienced with conventional buildups because of long, low-rate afterproduc-tion periods are eliminated by fIow tests. Other anomalous pressure buildup effects, such as "humping" due to weli-bore phase segregation, can be successfully eliminated with the new method. Generally, flow tests of about 24 hours' duration run with conventional pressure measurement equipment are sufficient for interpretation purposes. Field testing of the two-rate flow test method has established that it is a reliable and economical method which can be used in many instances to complement or even replace conventional pressure buildup methods. INTRODUCTION The principal method for estimating formation permeability and well damage, or skin factor, in a producing oil or gas well is the analysis of shut-in bottom-hole pressure buildup data.' This familiar method has been used quite successfully by reservoir engineers for many years. It is based on the solution of the radial flow equation for constant rate conditions, and requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed t + ?t bottomhole pressure vs log t + ?/?t(where At is shut-in A? time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the permeability, skin factor, and reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. Over the years several drawbacks have become apparent in the use of conventional shut-in pressure buildups for determining permeability and skin factor. The conventional pressure buildup interpretation theory assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing in to the formation. This adjustment period is commonly referred to as the "after-production" portion of the pressure buildup. In the tight reservoirs, long, low-rate after-production periods frequently occur, and the well must be shut in for several days or, in some instances, even weeks to obtain an interpretable buildup curve.' Obviously, such long shut-in times can cause loss in current income, both from reduced oil production and from the fact that personnel and pressure measurement equipment are occupied with a single well for too long a time. In other cases, even long shut-in periods do not seem to be of much aid in obtaining an interpretable buildup." If there is considerable phase redistribution (liquid fallout or bubble rise) after a well is shut in, then curves with no interpretable portion are often obtained during the buildup. In addition to instances in which wellbore effects cause trouble, there are also cases in which the major objection to use of the closed-in pressure buildup is simply the fact that the well must be shut in. When there is no proration and when the well has limited producing capacity. closing in the well means loss of income. From the foregoing discussion it is apparent that it ib desirable to have an alternative method of obtaining the same information as that derived from a conventional buildup without the need of closing in the well. One possible solution which has been offered for this problem is the use of a bottom-hole shut-in tool' which isolates the major portion of the flow string from the formation face during the buildup. In this paper an alternative method which is frequently successful in avoiding wellbore effects and which does not require the use of special equipment is presented. A new, simple method has been developed with which the flowing bottom-hole pressure data from flow tests in oil or gas wells can be used to estimate permeability, skin factor and the average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized production rate of the well is changed to another, higher or lower rate. The need for closing in the well is eliminated, and pressure measurement periods of only 18 to 24 hours arc usually sufficient, even in tight reservoirs. Thus, the new

By J. W. Leonard

This expanded and more detailed supplement to earlier published work1 is offered as a means to demonstrate the high empirical correlation which exists between the readily measured coal bench scale test parameters of volatile matter (d & a.f.), Hard-grove grindability index (HGI), Koppers cone bulk density (BD) and pulverization level (% passing a 1/8-in. screen) to the less readily measured full scale coke stability index. Thus, Fig. 1, 2 and 3 represent the correlated test data contained in Tables I, II and III respectively. Ninety-six coals are correlated so that 97% of the resultant cokes fall within two points and 100% fall within three points of the actual tested coke stability indices. The main generalizations which can be drawn from the correlation of these coals are as follows: 1) The coke stability indices for higher bulk density coals (46.0 BD to 50.6 BD) appear to be largely influenced by differing combinations of factors for coals above and below a pivotal point of approximately 36% to 37% volatile matter. Below this pivotal volatile matter coke stability index appears to be influenced largely as a result of changes to the coal volatile matter and pulverization level. While above this pivotal volatile matter coke stability indices appear to be dependent on the coal hardness, as measured by the HGI, and to some extent upon coal volatile matter. Pulverization appears to have little influence on the coke stabilities of the harder coals (52 HGI to 58 HGI) of greater than 36% to 37% volatile matter. 2) The coke stability indices for lower bulk density coals (41 BD to 45.9 BD) appears to be largely influenced by changes to coal volatile matter and pulverization level for softer coals above approximately 58 HGI. 3) The main empirical observation to be drawn from these results is that for coals above approximately 36% to 37% volatile matter the quantities of hard and soft constituents as measured by the HGI are important when defining coal rank for correlation to the coke stability index.

Jan 1, 1965

By C. B. Manula, H. Gezik

In planning modem-day mining operations, management needs to pass from the area of subjective decision-making to an area of objective decision-makirlg. Planning procedures currently being practiced by many mine managers depend primarily on common sense and trial-and-error methods which oftentimes never reach optimum solutions. For this reason, an attempt is made to provide an understanding of linear programming to solve production planning problems. More specifically, a linear programming model is proposed to solve the production scheduling problem as it was found to exist in the crushed stone industry. Optimal production scheduling is of prime concern here, since the industry has to cope with seasonal demands for its products. The solution, as determined through the application of the model, provides management not only with an optimal production schedule but also with the following information regarding the improvement of existing facilities: (I) the location of bottlenecks which limit production and profit; (2) the directions in which the company i fixed equipment should be expanded or modified; and (3) the evaluation of unused resources. Future trends in stone production will quite likely parallel those in the construction industry. Continued record expenditures for structures such as dams, highways, and buildings are the reasons for this accelerated growth. Production forecasts for the next decade are predicted to be around one billion tons with an approximate 7% annual increase. The problem of increasing production from 570 million tons in 1966 to 1 billion tons by 1976 offers no small challenge. This situation is further compounded by other problems and economic factors. Population expansion, government regulation, labor agreement, and changes in technology wd cause managers and operators to be confronted by many more complexities than characterize present-day operations. Some of these. problems and economic factors are: (1) In some metropolitan and other urban areas, easily accessible sources of stone are almost depleted. Transportation costs will be a prime concern of the industry. (2) Population growth has forced residential expansion to a point where many quarry operators must conform to urban and suburban regulations. (3) Government regulation in regard to air and water pollution, noise, and reclamation as well as zoning developments necessitate that crushed stone producers keep abreast of changing conditions and requirements. (4) The crushed stone industry operates under pressure of a highly competitive situation. Every company's objective is to retain a favorable marketing position by exercising great attention to production and marketing costs. This is rather difficult, since the crushed stone industry is one segment of modern mining which has to cope with a seasonal demand for its products. Among the problems posed here, the one of exercising great attention to production and marketing costs is of current interest to management. Under seasonal demand conditions, this problem creates further difficulties for managers who need to plan and forecast. STATEMENT OF THE PROBLEM Various methods of Operations Research have been developed to handle a problem whose genesis is explained above. It is very seldom, however, that these quantitative means are used in practice by the mining industry. This paper describes the use of Operations Research methods to solve a production planning problem when demand is seasonal. The seasonal production planning problem is an important one because of the substantial costs associated with changing production, employment, and inventory levels to adjust to seasonal sales patterns. Most companies try to operate within reasonable levels of employment changes and hold inventories within storage capacities. In general, little or no attempts were made to develop minimum cosl schedules or to provide objective means to compare various production policies. When demand varies within a fixed time period, 11:-oduction requirements may be met by following one

Jan 1, 1970

By S. E. Maddigan, B. R. Zimmerman

MOST metallurgists are well acquainted with the contributions already made to the study of metals by the use of X-rays. On the one hand, the radiographic method is constantly becoming of increasing importance as a nondestructive testing procedure, while on the other hand the techniques of X-ray diffraction have made important contributions to the fundamental knowledge in studies of phase diagrams, stress conditions, and so forth. A new, and as yet insufficiently appreciated, tool exists in the application of microradiography to alloy structures. This new procedure in many respects bears the same relation to microscopic investigations as does macroradiography to the gross inspection of metal surfaces. However, where macroradiography is used ordinarily to determine the soundness of the metal structure, this new method can be used not only to investigate micro-un- soundness but also to examine the distribution of the constituent elements within the body of the alloy. When combined with the normal procedures of microscopy, this offers a technique of great potential power. It is intended in this paper to present a few examples of copper-base alloys demonstrating the additional knowledge obtained from the microradiographic method. The detection of micro-unsoundness is demonstrated in Fig. I for a sample of cartridge brass as cast. The sample appeared quite sound when viewed under the microscope, but in reality was thickly populated with minute voids. This application of the method conforms in every way to conventional large-scale radiography and has been used to facilitate production of metal for vacuum devices.1 The true potentialities of the technique are revealed by comparison of Figs. 2a and 2b, which are respectively a- photomicrograph and a microradiograph of a cast alloy of 80 per cent Cu, 10 per cent Sn, 10 per cent Pb. The remarkable difference in appearance provides some concept of the additional information this method may yield when used as an auxiliary to microscopic studies. Fig. 2a shows two phases of the copper-tin system plus segregated lumps of lead. Fig. ab, on the other hand, shows with exceptional clarity the actual dendritic growth of the metal crystals during solidification. The practice of microradiography depends upon the laws of absorption of X-rays. This subject has been reviewed thoroughly in recent papers,1,2,3 but for clarity a brief resumé will be given here. As is well known, when a beam of X-rays is transmitted through a layer of homogeneous material, the intensity is reduced according to the relation:[ ]

Jan 1, 1944

By H. H. Kaveler, Z. Z. Hunter

Variation of the horizontal permeability (parallel to the bedding plane) in the vertical section of reservoir rocks has long been observed as a characteristic of a normally heterogeneous system which reservoir rock represent. The use of a recently developed water injection profile device offered opportunity to measure with a high degree of reliability the rate of inflow of water into Burbank sandstone in wells previously cored. Water injection profiles were not correlative with core permeability profiles in such wells. Apparently the vertical permeability substantially influences the flow between strata in a formation in a manner as to void the usual conclusions that have been drawn from consideration of the horizontal permeability measurements alone. The results obtained in comparing water injection profiles with horizontal permeability profiles suggest that many of the usual production operations based upon "selective" behavior or treatment of rock exposed in well bores need to he re-valuated and re-examined. INTRODUCTION Petroleum reservoir rock are heterogeneous systems. Heterogeneity exists in respect to lithologic character insofar as such rock are composed of distinguishable solid phases. Heterogeneity also exists in respect to certain properties, such as porosity and permeability, that vary due to variation of the physi-cal structure of the rock. Except in exceptional cases, both the horizontal permeability (measured parallel to the bedding planes) and the vertical permeability (measured perpendirularly to the bedding planes) exhibit significant variation in any common source of supply. The variation in horizontal permeability. as reflected by con. analyses. has drawn the greatest attention of petroleum technologists probably out of the general notion that the mass movement of fluids in a reservoir is predimonantly in the horizontal direction. Furthermore, in the usual case, the rock permeability measured in the horizontal direction is greater than that in the vertical. The variation of horizontal permeability of reservoir rock has been the basis for developing a number of operating practices and procedures intended to improve the petroleum production operation. Many such procedures are referred to as "selective" in the sense that the practice is intended to control the flow to a more. or less. permeable interval within the common source of Supply. It is often said that such practices are "tailored" to the permeability profile. The practices referred to involve, among others, the following: selective perforation of casing; selective shooting, acidizing and plugging: plugging back to intervals of low permeability; and, regulation of flow to prevent coning of water or gas, or irregular encroachment of water or gas. Certain expressed notions involving a concept of "by-passing," or "trappingl" that are held to be particularly harmful in causing the avoidable loss of recoverable petroleum have grown from observed variations in the horizontal permeability. Oftentimes estimates of the reserve of a common source of supply are tempered by conclusions relating variation in horizontal permeability to recover-ability of the oil-in-place. Certain conclusions attributed to the significance of the variation of the horizontal Permeabilitv often extend to the design and operation of pressure-maintenance projects involving both water flooding and gas-injection. Many advocate increasing the number of injection wells, advocate maintaining uniform and equidistant input-output well patterns, or advocate so-called "dispersed" gas-drive techniques rather than gas-cap injection because the permeability profile of cored wells is supposed to indicate that "by-passing" or "trapping" would otherwise exist. It is important, therefore, to have an opportunity to test whether the variation in the horizontal permeability found through core analyses of a typical reservoir rock is sufficient to establish the paths of fluid flow in a reservoir. It is particularly important to have an opportunity to determine whether flow at the sand face of a well conforms to the permeability profile as established by core analyses. In that manner, the merit of certain 50-called "selective" operating procedures and other notions may be evaluated. The purpose of this paper is to compare horizontal permeability profiles of wells in the Bartlesville (Bur-bank) sandstone with water injection profiles, for the purpose of showing that there is no correlation between the horizontal permeability of a core and the water intake characteristics of a typical sandstone. GENERAL CHARACTERISTICS OF BARTLESVILLE (BURBANK) SANDSTONE The Bartlesville sandstones of Northeastern Oklahoma are off-shore bar deposits.' Although other reservoirs had different processes associated with their deposition or with the formation of their porous, permeable structure, the l!artlesville sandstones on which these field Fields were made are, in every respect. typical petroleum reservoir rock. The permeability of the Bartlesville sandstones shows a typical variation in both the horizontal and vertical direction. Furthermore, the permeability profile logs of wells in any pool are not correlative, even as between wells as close as 660 ft and 330 ft apart.'. The same condition exists in such sand-tones as the Jones Sand at Shuler' and is the ordinary and usual characteristic of reservoir rock. THE FIELD DATA The data reported herein are those obtained from coring of nine wells on the center of ten-acre locations for the purpose of providing water-injection wells in the Bartlesville (Burbank)

Jan 1, 1952

By H. L. Gilbert, H. A. Johansen, R. G. Nelson

High purity electrolytic chromium plate has been hydrogen-reduced and arc-melted under inert atmosphere to give sound ingots. These ingots may be hot forged to break the as-cast structure and then worked at 500°C to finished form. An intermediate and final high temperature anneal gives best ductility and grain refinement. HE increasing interest in refractory metals for I use in high temperature gas turbines, jets, and rockets has led to great efforts in exploiting the fifth and sixth groups of transition elements. Much of the interest has centered upon production of metals that can be worked and fabricated by normal means to produce various engine parts or components having the high temperature characteristics of oxidation resistance and high creep strength required for such uses. If these pure elements do not exhibit all of the desired characteristics, it may be possible to obtain a high purity alloy that will. Since, in all cases, development of these transition elements has depended to a large extent upon removal of oxygen and nitrogen as a means for producing ductile metal, the hypothesis has been accepted that oxygen is the normal embrittling material in a high grade electrolytic chromium metal. Various methods have been employed in an effort to remove this oxygen by direct or indirect attack.' Many workers have endeavored to produce pure chromium through reduction of the oxide by carbon or active metals, while others have recommended fusion electrolysis of chromium salts or reduction of these salts by active metals, such as sodium or calcium. Hydrogen reduction of the oxide or chloride and thermal dissociation of the iodide have been reported to give high purity metal. Experimental Work The U. S. Bureau of Mines, Northwest Electro-development Laboratory, has systematically re-examined the more promising methods and developed two which produce metal having ductility at temperatures lower than heretofore described. It has been found' that oxide-free chromium chlorides in a NaCl-KCl carrier salt may be mag- nesium-reduced and the byproduct salts distilled off in vacuo to give a high purity chromium sponge. Fusion analysis conducted under the supervision of W. W. Horton of Knolls Atomic Power Laboratory showed the oxygen and nitrogen both to be below 10 parts per million on a selected sample. A small amount of carbon is carried over in the final metal from the chlorination and reduction steps which are carried out in graphite crucibles. This trace of carbon is not detrimental to hot ductility. A more practical method for producing ductile metal is through hydrogen reduction of high purity electrolytic chromium. Normal electrolytic chromium will, if "developed" for a few minutes at 1100°C in high vacuum, be found by the method of Adcock:; to contain about 1 pct chromium sesquioxide (Cr2O3). This small amount of oxygen may be effectively reduced by hydrogen.2, 4 The method employed was to crush electrolytic chromium plate in a gyratory crusher to pass 60-mesh; finer crushing appears to offer no advantage. A nitric acid leach removed the iron picked up during crushing. The leached powder was rinsed until neutral with distilled water and vacuum-dried.

Jan 1, 1954

By Cecil J. May

The importance of a knowledge of the physical laws involved in the production of oil from a reservoir has come to be generally realized in recent years and it is therefore unnecessary to elaborate on the many problems which still await complete solution. Among them the vertical flow of mixtures of oil and gas has attracted considerable attention and a number of papers have appeared in the literature from time to time. The complete solution of the problem would cover such aspects of oil-field technology as the calculation of bottom-hole pressures from purely surface data; the estimation of natural flowing lives; the design of gas-lifts and the selection of tubing for natural flow, and so on. It is still true, however, that the results so far published have not been particularly consistent and there are no generally accepted data available of universal applicability. It is, in fact, by no means easy to obtain a sufficiently wide range of variables under the operator's control to determine the laws of flow without ambiguity and much of the published research has been directed towards the solution of the specific problems of individual fields representing only a partial treatment of the whole subject. It was with a similar object that work was commenced on the Masjid-i-Sulairnan field of the Anglo-Persian Oil Co. towards the end of 1930 and has since continued as opportunity offered. Of course, the results obtained cannot necessarily be applied elsewhere without modification and, in some cases, considerable extension. At the same time conditions in this field are somewhat unusual in allowing certain aspects of the problem to be isolated and examined without the disturbing effects of a large number of independent or partially independent variables. For example, since the field is under unit control, it is possible to maintain steady conditions on any particular well over long periods. Moreover, the structure of the limestone reservoir is such that the gas-oil ratio for a given well is sensibly constant over very wide ranges of production rates, and in many cases the bottom-hole differential pres-

Jan 1, 1935

By D. D. Dunlop, J. R. Welker

The growing interest in the use of CO, in crude oil recovery increases the need for data on the effect of CO, on hydrocarbon physical properties. Data are presented on the solubility of CO, in various dead oils, the swelling changes in CO2-oil solutions and the effect of CO, on dead oil viscosity. This latter property shows the most pronounced effect, with viscosity reductions up to 98 per cent of the uncarbonated viscosities. An empirical method of estimating the viscosity of carbonated oils is presented. The apparatus and procedures used are described in sufficient detail to allow others to make similar studies. INTRODUCTION The effect of dissolved carbon dioxide on the swelling and viscosity reduction of specific hydrocarbon oils has been observed and recorded by a number of investigators.'- me object of this paper is to offer a means of predicting these effects for crude oils free from natural gas, using the dead state viscosity and gravity of the crude oils. The CO, solubility and swelling of numerous crude oils were determined in a visual cell at various pressure levels. The viscosity of the oils carbonated to various pressure levels was then determined by measuring the pressure drop across a capillary tube. From these data, the physical properties were correlated empirically. The resulting correlations allow the prediction of CO, solubility, swelling and viscosity reduction if the dead state gravity and viscosity of the oils are known. SOLUBILITY AND SWELLING MEASUREMENT EQUIPMENT AND PROCEDURE A high pressure visual cell was installed in a constant temperature cabinet. A test gauge was attached at the top of the cell for pressure measurement, and a line was run through the cabinet wall to a wet test meter which was used for volumetric measurement of the gas. The first step in making a test run was to put the oil in the cell up to a level about half to two-thirds of the total volume. This required about 50 to 65 ml of oil. carbon dioxide was then bubbled up through the oil for a time during which the pressure of CO2 in the cell was kept above 800 psia. Saturation of the oil with CO2 at this pressure and ambient temperature was confirmed by slowly bleeding CO2 through a valve to the atmosphere. If the oil was completely saturated with CO2, bubbles of gas would form in the oil at the first small decrease in pressure. If the oil was under-saturated, no bubbles formed until the pressure was decreased to the saturation pressure existing in the oil. If this saturation pressure was lower than that desired, more CO2 was bubbled through the oil until the desired level was reached. After saturation at ambient temperature was completed, the cabinet temperature was adjusted to the desired level and the cell was allowed to reach temperature equilibrium. After temperature equilibrium was reached, the pressure was again decreased slightly, and the oil again checked for full CO2 saturation at the cell pressure. The pressure now had changed because of the difference in solubility of the CO, in the oil at higher temperatures and the expansion of CO2 as the temperature increased. The outlet tube from the cell was then connected to the wet test meter and the CO2 was allowed to flow slowly out of the cell and through the wet test meter at ambient temperature and pressure. The water in the wet test meter had previously been saturated with CO2 at ambient temperature and pressure by allowing CO2 to flow continuously through it lor a period of several hours. The gas flow was stopped at several pressures during the run and the cell was allowed to come to equilibrium; this made possible the measurement of solubility and swelling data at the intermediate pressures. The volume of the oil in the cell was recorded at each of the equilibrium pressures in order to obtain swelling data. DATA AND RESULTS The solubility of CO2 in the oil was calculated by the relationship V — V, where R. = solubility of CO, in crude oil, cubic feet of CO, measured at 60F and 1.0 atm/ bbl of dead state oil at the temperature under which solubility was measured, V, = volume of gas released from the cell between the saturation pressure and zero pressure, corrected to 60F and 1.0 atm, cu ft, V, = volume of CO: contained in the gas space above the oil, corrected to 60F and 1.0 atm, cu ft, and V, = volume of the dead oil in the cell in bbl at the temperature of the run. The volumetric data of Sage and Lacey' were used to calculate V., from the volume of CO2 at high pressures. The swelling factor was calculated as where V, is the volume of the C0,-

By Ernest Gayford

When the United States Government started buying gold at varying prices per ounce, set by the President and the Treasury Department, the gold miner found himself facing new conditions, as gold became a commodity with a fluctuating market price. While it was self-evident that the miner was to receive more for his gold than the old established price of $20.67 per ounce, there was an element of uncertainty, which made it difficult, and perhaps dangerous, to decide to invest his time and money to produce gold, especially if the profit would represent only the difference between $20.67 an ounce and the new price as set from day to day by the Government. When, however, on Jan. 30, 1934, the United States went off the gold standard, the price of newly mined gold being rather definitely set at $35 per ounce, with some assurance that the price would be maintained at or near this figure for a long time to come, the gold miner was justified in revaluing his property on the basis of the new price, and the prospector was offered inducement to spend his time and energies hunting for new mines, or going back to old locations previously abandoned as of doubtful value. It is interesting to see what this new price means to the producer of newly mined gold, and how much of the increase is passed on to the producer. It will be found that, as with the base metals, the nearer he can get to producing a finished product himself the greater his reward will be; the net returns for bullion being necessarily higher than for the same amount of gold shipped in concentrates to the smelter. Bullion can be shipped to the United States mints or Government assay offices under the following terms and conditions. An affidavit must accompany the shipment, stating, among other things: 1. The source of the gold; whether ore, tailings or placer. 2. The tons of ore, tailings or cubic yards of gravel from which the shipment was recovered.

Jan 1, 1935

By R. B. BRINSJIADE

THE following is an attempt to form a formula by which a mine call be quickly evaluated, after all pertinent physical data have been collected from observations on the ground by a competent mining engineer. ASSUMPTIONS. Let G = price to be paid for the mining property. M = cost of developing the mining property to yield y tons of ore daily. P = cost of suitable plant to treat y tons of ore daily. p = value of said plant when the mine has.been exhausted. C = total fixed capital investment. W = working capital investment

Jan 1, 1908

By Kenric C. Owen

INTRODUCTION Situated 23 miles east of Pretoria the Premier Mine started diamond production in 1903. Two years later it produced the largest diamond yet discovered, the 3 106 carat Cullinan stone. For the period to 1932 when the mine was closed down due to economic circumstances, open cast mining was practised using inclined rope haulage traction and by this time had produced 48.5 million carats of predominantly industrial quality diamonds from 148 million tons of ore. In 1945 it was decided to re-open the mine using underground mining methods. A system using long hole benching was devised (Hodgson and Sewel 1960). This system was later modified but still forms the basis for approximately fifty percent of production. Following the successful introduction of block caving on associated diamond mines in the Kimberley area (Gallagher and Loftus 1960) this mining method was introduced to the Premier Mine in the late 60's and now accounts for nearly 50% of production. This paper will discuss block caving at Premier Mine in the light of our experience and discussion will be directed to the main geological and structural features of the orebody and host rocks and the related constraints imposed on the mining methods. Reference is made to the long hole benching mining method for comparative purposes. GENERAL DESCRIPTION OF OPERATIONS The ore from the block caving and bench mining areas gravitates via ore passes to a twin haulage, 500m below surface. Electric 13 tonne locomotives, each hauling a train of 10 Granby type cars, deliver the ore to two 42" x 48" (1.06m x 1.22m) jaw crushers. The ore is reduced in size to minus 0.15m before being hoisted to the treatment plant on surface. Hoisting is done with 12.5 tonne bottom discharge skips in a five compartment rectangular shaft using two 3 240 H.P. semi automatic Ward Leonard winders. A small single drum service winder operates in the other compartment. Men and materials travel in a separate shaft in a 5,4m x 2,8m cage operated by a Koepi winder. These two shafts are also the main intake airways to the mine. The two main extraction fans capable of 250 m3/s at 3,2 kPa are situated on surface and are connected to the underground workings by an incline and a network of air passes and return airways. GEOLOGY Although there are numerous occurrences of kimberlite bodies in the district, the Premier Mine kimberlite pipe is the only economic orebody. It is roughly oval in shape with surface dimensions of 900m on the long axis and 450monthe short axis. The surface area is 320 000 m2. The kimberlite has intruded a massive body of felsite and norite which is intersected by a number of faults. The contact between the kimberlite and host rock is clear cut and dips inward at an average angle of 80°. Cutting across the pipe and the country rock is a 75 metre thick gabbro sill, the top of which intersects the pipe below the 347m level and dips at 15' to the north west. The kimberlite has been metamorphosed a distance of some 20m both above and below the sill contacts. Age measurements on biotite from the gabbro date the sill as 1 115 million years, thereby providing a minimum age of the pipe. (Pre Cambrian). All other pipes in South Africa are of Cretaceous age (60 million years). A simplified geological plan and section of the Premier Mine orebody is shown in Figure 1. It is thought that the kimberlite intruded in at least three distinct phases. The kimberlites of these different phases can be distinguished most easily by their characteristic colour. BROWN KIMBERLITE. This is the oldest kimberlite and forms a crescent shape in plan on the south eastern side of the pipe. In depth it increases in relative area. Although the brown kimberlite carries the highest diamond grade in terms of carats per ton all the various kimberlites in the Premier pipe are economic to mine.

Jan 1, 1981

By G. L. Jr. Spencer

THERE is no question as to the importance of the part played by the retort in modern zinc smelting. A satisfactory retort should have properties that will result in resistance to slagging action and fire cracks, and have no tendency, or at least, only a small tendency, to soften and bend under furnace heat. The life and cost of a retort also are extremely important factors. The trend in zinc smelting during the past few years has been toward longer retorts and higher charge density. This is caused by the fact that the diameter is limited to 9 or 10 in. because of heat penetration difficulties in larger sizes. Consequently, increasing the length of the retort and density of charge offers the only practical means of increasing the amount of zinc produced per retort. The stiffness of a retort perhaps is the most important factor, as slag accumulates in the bottom of a retort which has sagged and very quickly cuts through, often ruining the retorts below. The development of the high-silica retort is a result of the demands made by the trend toward heavy charges.

Jan 1, 1931

By R. L. Huntington, D. T. MacRoberts, Charles R. Hetherington

SINCE the equation of continuity governing transient flow of gases through porous media cannot be integrated mathematically into a simple usable expression free from series terms, empirical and approximate equations have been advanced relating cumulative production and future production rates from gas reservoirs with time. In order to check the accuracy of these empirical equations and to obtain an insight into the initial conditions pertinent to the solution of the fundamental equation of continuity, experimental work has been conducted on a vertical 2-in. tube, 91.6 ft. high, packed with unconsolidated Wilcox sand. The results presented in graphical form show the accuracy of the approximate relations. Data from unsteady-flow runs on the 2-in. experimental tube are presented graphically, and are applied to obtain an equation for this specific case, and are offered as an aid in future investigations of this basic equation. The close agreement between equations calculated for steady-state flow and the experiments indicates that the decline of actual gas reservoirs may be treated by an application of these equations without serious error.

Jan 1, 1942

By C. A. Allen

FOR over three years we have been endeavoring to reduce the number of fatalities and minor accidents in Utah. The physical condition of the o? Represents the average of 4 States mentioned excluding the catastrophes indicated. FIG. 1.-NUMBER KILLED PER MILLION SHORT TONS OF COAL PRODUCED IN COLO¬RADO, NEW MEXICO, UTAH, WYOMING, AND BITUMINOUS MINES OF THE UNITED STATES, 1914 TO 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 5, 1922

By J. S. Koehler, F. Seitz

THE dislocation theory of plastic flow originated in 1928, when Prandtl1 suggested that the internal damping of metals of plastic origin might arise from the motion of a crystalline imperfection. Following this, Dehlinger2 employed a similar imperfection in a theory of recrystallization. The first detailed theoretical discussions were those of E. Orowan3 and G. I. Taylor4 in 1934. The resulting theory was gen- eralized by J. M. Burgers5 in 1939. Mott and Nabarro, in England, and Seitz and Read,6 in the United States, started an extensive examination of the atomic theory of dislocations in the period between 1939 and 1941. However, this development was arrested by the mar and was not taken up again until after 1945. Since 1946, the field has been the object of very intense activity, particularly in the United States and England. Dislocations are beautiful and intricate imperfections; they are sufficiently complicated to account for the great variety of phenomena encountered in the field of plastic flow. Above all, the dislocation concept enables us to understand how a metal or other plastic solid can deform inelastically under very small stresses at temperatures far below the melting point. Suppose we attempt to shear a perfect crystal plastically. This can be done by sliding one entire atomic plane simultaneously through one atomic distance with' respect to the near-

Jan 1, 1954

By Joseph Jensen

CURTAILMENT of oil production in California began in 1922 and 1923 when certain of the major companies completely shut down some pumping properties. Efforts of this kind were generally carried on without coordination by individual companies until 1923. From May to August of 1923, oil production in the Los Angeles Basin was curtailed because of lack of pipe-line outlets. This work was handled by a small committee of executives and engineers of some of the pipeline companies without any established. Method such as obtains at present. Not all of the major companies participated in ibis curtailment and the effort was not well organized. The problem then was principally to move the oil. The crisis passed in September of 1923 from then on the major companies each on it own initiative, shut in additional production. At Domiuguez, in 1921, Shell, Union and Associated agreed to limit drilling to a 100-ft. zone for one Near. In the summer of 1925, operators at Ingde-wood agreed to limit developments to a 1300-ft. zone during the 1925 drilling campaign. In the summer of 1927, the Ventura operators cut back their production one-third and deft it thus for 90 day. Drilling in this field has always been at a slow and conservative rate.

Jan 1, 1932

By T. S. Lundy, R. E. Pawel

Effects of short-circuiting paths on observed diffusion behavior in real crystalline systems are considered. It is concluded that experimentally measured diffusion coefficients may vary widely from values associated with true lattice diffusion to those appropriate for short-circuiting paths alone depending upon the conditions of the experiment and the sensitivity and completeness of the data. IN 1961 Harrison1 classified experimentally observed diffusion behavior in systems involving both lattice and dislocation-enhanced atomic transport into three categories. His types A and C were limiting cases where the measured diffusion coefficients using the usual serial sectioning techniques were representative of lattice diffusion (with only slight effects of dislocations) and dislocation-network diffusion (with only slight effects from lattice diffusion), respectively. In both cases A and C for a sectioning experiment in which the diffusion couple has the semi-infinite geometry and unidirectional diffusion takes place from a plane source located at the origin of the coordinate system, he pointed out that Gaussian penetration behavior should be observed. For case A the lattice coefficient should be slightly enhanced by dislocation contributions, and the model of Hart2 can be used to predict the amount of this enhancement. For case C the observed coefficient should be that for the dislocation network and have little or nothing to do with lattice diffusion. Hart's model in its general form is still applicable, but the apparent diffusion coefficient for this case is virtually independent of dislocation density. Harrison's case B is that for which non-negligible contributions exist for transport by both mechanisms and "the concentration distribution does not approximate to any simple form." With the possible exception of very low temperatures where diffusion distances approach atomic dimensions, any real diffusion specimen will in general show non-Gaussian behavior provided the data are complete enough to uncover it. Thus, a "complete" set of data for any real system cannot be expected to be totally amenable to treatment by a simple mathematical model which does not take into account the relative distribution of transport by the various modes or submodes. For a particular sensitivity of specimen analysis and at a given temperature of annealing if the concentration profile could be observed as a function of time, "the behavior will initially be type C, and will develop into type B. and ultimately type A".1 Thus, it appears that the type of diffusion behavior which is experimentally observed in a given system depends very much upon the particular experimental conditions and the particular tools available to obtain the data. Interpreted in this fashion, Harrison's classification refers not to the diffusion behavior as a whole but to the relative sensitivity of the method of examination and completeness of the data. In the present paper we will: 1) assume that the measured penetration behavior follows the same general classification as that proposed by Harrison; 2) give, for diffusion in tungsten, examples of the range of diffusion coefficients that it is possible to obtain in a single experiment; and 3) speculate that some arguments which consider the possibility of short-circuiting effects being responsible for "anomalous" diffusion in several bcc metals may have been discarded prematurely.3 Both monocrystalline and polycrystalline tungsten were used in this work. The former was obtained as triple-pass, electron-beam zone-refined 6.0-mm-diam rod from Materials Research Corp.. Orange-burg. N.Y. The latter was swaged, high-purity bar stock which was annealed for 2 hr at 2200°C and 10-9 torr to yield an average grain diameter of about 25 /i. The tracer Nb95 was received in oxalate solution from the Isotopes Division, Oak Ridge National Laboratory. Experimental procedures of specimen preparation, isothermal diffusion annealing, serial sectioning by anodizing-and-stripping, and y counting of the individual sections to determine the tracer penetration profile after a given diffusion anneal have been described elsewhere.4 However, it should be noted that the anodizing-stripping sectioning technique has the particular advantage for this research of permitting sectioning to be accomplished over a wide range of

Jan 1, 1970

By Richard Franchot

DISCUSSION of a paper is sometimes more in-teresting in what has not been said than in what is said. In the present case the paper is mainly directed to certain thermo-dynamic relation-ships in the blast furnace. Careful reading of the dis-cussion fails to show a single use of the term, heat unit, or its equivalent. If we wish to know very-much about the furnace action it is necessary to count calories or B.t.u. Nothing much is. said about the availability of heat at high temperatures, although it will be generally admitted that in seeking underlying limiting factors in the furnace economy the hearth heat relations offer-the most promising clues. Those discussing the paper, with exceptions of course, apparently have failed to recognize an outstand-ing fact. It is a fact that the heat actually generated by the air oxygen in CO formation (including the blast heat) is in excess, after charging off radiation, etc., by from 70 to .90 per cent over the heat absorbed in melting the iron and slag and calcining the stone reduction by CO absorbing no heat. The fact stands out as plainly as does the fact that the furnace functions largely as a gas producer. The surplus heat is there. It is in the picture. Why not take a look at it, face the fact? That the surplus heat is necessitated by the hearth conditions admits of very little if any doubt. The furnace is really two separate pieces of apparatus: the hearth, doing certain work, and the superimposed shaft, doing certain other work. The combustion of fuel in the hearth, primarily serving the hearth pur-poses, generates much more heat and gas than the shaft requires, or can use, in smelting work. The result is surplus heat makes still more gas in the heat-absorbing reaction between CO, and coke; what is left of the surplus going to top heat. Here we have a simple yet adequate sketch of the furnace action. Having obtained a fairly comprehensive view of the existing heat relations of both hearth and shaft, the way to improvement seems quite plain. Either do more of the work above the hearth or put more heat into the hearth. Since there is already a great surplus of heat above the hearth, probably little needs to be done by way of increasing the proportion of the work done in the shaft. The shaft can, however, probably do much more work than it is now doing provided that a way, can be found to get more work, done in the hearth. The hearth heat is nicely balanced. Losses by radiation and water cooling and other losses are already taken care of. Any increase of hearth heat development could be utilized in taking care of increased smelting work. Aside from the possibility of increased blast heat, there is one sure way of putting more heat into the hearth, and this is to blow more air. And since the shaft already has more gas than it needs, the increased gas resulting from the greater blast volume can be withdrawn from the bosh after it has done its work in the hearth. Now an increase of burden will cool the shaft, cut down solution loss and thereby supply addi-tional coke in the hearth to burn with the additional air blown. The hearth heat per pound of coke charged will be proportionately increased. The balance between hearth and shaft will be better. Gruener's ideal will be more nearly attained, if not exceeded. Most inter-esting of all perhaps, the more the burden is increased, the more coke will reach the hearth and the more burden can be added. The effect is to be cumulative.

Jan 3, 1927

By Ernest Stütz

The problem of increasing blast-furnace efficiency through diminution of flue-dust production while operating with burdens consisting largely of fine ores has of recent years attracted the attention of metallurgists, whether directly or indirectly interested in the economies of iron smelting, and the various methods evolved from theory or practice have been submitted to wide discussion. After the very thorough and, at that time, exhaustive view of the whole subject, which was afforded to the industry by the meeting of this Institute in February, 1912, the subject was again taken up at the meeting of the Verein deutscher Eisenh?ttenleute at D?sseldorf in December, 1912. While American and German conditions are not entirely identical, it may be of interest to give here the words of the gentleman summing up the discussion at the Diisseldorf meeting: " The chief advantage offered by the use of briquettes lies in the fact that disturbances in the furnace, caused mostly by the presence of fine ores in the burden, are avoided, and that blast pressure can be considerably reduced. The resulting economies cannot be overrated, as, with lower blast consumption per ton of product, the installation will be able to take care of increased production. In consequence of lower pressure and speed of blast, heat is more efficiently utilized, flue gas temperature is lowered, and coke particles are less liable to be carried along with the flue dust, of which considerably less is produced. Finally, by increased regularity of operation and higher temperature in the lower parts of the furnace, the quality of the product is improved. The question of briquetting iron ores has grown to be one of the most important in the iron industry, and it is not any more a question of what is the cost of briquetting a ton of ore, but what, in using ore briquettes, is the cost of production of a ton of iron." Dr. A. Weiskopf, of Hannover, admirably condenses in these words

Jan 1, 1914

By AIME AIME

Council may deal with any matter of general interest, for which joint action of two or more of its member societies would have been appropriate, if Council had not been established. Council may initiate and carry through projects of the general character defined in the By-Laws, for which the necessary financial provision has been made. Council may take up, and in its discretion act upon, any matter of general interest referred to it by any member society or by any other society, national, state or local, or by any branch of Government, or by any individual or group of individuals.

Jan 1, 1920