Search Documents

By W. J. Rogers, L. J. Dwiggins, R. O. Williams

THERE has been comparatively little work on the importance of strain rate and temperature as variables in the formation of deformation textures. For this reason the present work was started, the choice of compression being in part that of convenience and in part because of the absence of quantitative data in this area. These do not turn out to be important variables within the range studied which permits the results to be condensed into this note. Samples 1/4 in. in diam and 1/2 in. long were machined from 99.9 pct pure commercial aluminum and recrystallized to a fine grain size. A set of five samples were deformed between a spring-driven weight and an anvil resulting in roughly 20 pct strain each time. The strain rate varied because of decle-ration and shortening of the sample but would average about 10&apos; per min. Deformation at temperatures over the range of -76" to 150°C were obtained by heating or cooling the samples. Complete lubrication could be obtained by oil since the short time of contact did not permit its escape. The samples were compressed to a total true strain of 1.4 to 1.6. A larger sample was prepared similarly with spiral grooves in the ends to hold paraffin which provided essentially complete lubrication. This sam ple was compressed slowly at room temperature at a rate of about 2 per min to a total strain of 1.0. Cylindrical samples were carefully machined from these discs with a radial direction as an axis. They came from the center half of the samples and were roughly 1/16 in. in diam. The samples were etched down 15 pct to remove any surface effects. Diffraction data were then obtained for six different kinds of planes by the use of the Norton technique as applied to a fiber texture. Direct comparison between the raw data failed to reveal any significant difference between any of the samples and consequently the data from only one sample was completely reduced. The particular sample had been deformed at O°C The background was subtracted from the intensity data which were averaged over the four quadrants and then normalized to random. These data were then used to obtain fiber-axis distribution charts as previously described.2 For this sample the (422) plane was also run to assist in this inversion. The final result, Fig. 1, provided a comparable fit to that previously obtained from fiber data. About 85 pct of the material forms an elliptical texture around the <110> direction. The radius (at half height) is 5.5 deg along the (111) boundary and 8 deg along the (100) boundary. The remaining 15 pct forms a ridge running from this texture to near the <311> direction. The regions around the (100) and (111) planes are devoid of material. The earlier qualitative results of ~arrett~ are in complete agreement with the present results. The possibility has been dis-cused that the material around the <311> results from friction between the sample and compression plates.4 The present results are considered proof that such is not the case because of the uniformity of sample deformation and the requirement of axial symmetry before fiber-axis distribution charts can be accurately obtained. Recently results have been obtained to show that strain rate and temperature are important variables in the extrusion of aluminum.5 Perhaps the most important observation was that the partial recrystal-lization occurred even at room temperature. Strain rate was considered to be a factor only in that it produced a temperature change. There are many differences between the two experiments, the most important possibly being that their material was roughly ten times the purity of the present material. The present experiment, however, may not be as definitive as desired in this respect since it has been shown that compressed aluminum recrystallizes without a texture change6 although supplementary

Jan 1, 1961

By J. L. Martin, W. M. Campbell

A new electric logging method, called displacement logging, often gives a direct indication of the presence of mobile hydrocarbons in hydrocarbon-bearing formations. This method is based on the detection of a bank of connate water which is formed between the invading mud filtrate and virgin formation fluids in these cases. The existence of this phenomenon has beer, verified by laboratory studies and by actual field logs taken in known oil sands. INTRODUCTION During the past decade increasing use has been made of conventional electric logs to determine the amount of oil or gas in formations traversed by a borehole. This determination requires knowledge of several factors, such as true resistivity of the formation, formation factor, and water resistivity. Sometimes all of the factors necessary to make a reliable saturation calculation are not available. Also, the computations and corrections which are necessary in such a study often require the services of an experienced log analyst. It has long been the desire of exploration people to have a logging device which will locate hydrocarbon-bearing formations directly without requiring complex interpretation methods. The displacement log, while not completely fulfilling this desire, appears to be a Step in that direction. Basis for the Device The basis for this device stems from a phenomenon which occurs when mud filtrate invades a formation which contains displaceable hydrocarbons. As the mud filtrate invades the formation, most of the oil or gas is pushed out of the invaded zone, leaving residual oil. However, in addition to displacing most of the oil or gas, the connate water is also swept out, since the originally irreducible water is mobile in the presence of a water phase.1,2,3 Tonsequently, this irreducible water piles up as a bank between the virgin oil zone and the invading filtrate. If the mud filtrate is of higher resistivity than the formation water— as is commonly the case—the resulting annular zone, containing the bank of formation water, will be of lower resistivity than either the virgin oil-bearing formation resistivity or the invaded zone resistivity. This resistivity configuration, going from high to low to high again as the distance from the borehole increases, is found only in those zones which contain displaceable hydrocarbons. A device which would reliably detect this low resistivity zone would give a direct indication of mobile hydrocarbons. Illustrations This phenomenon is illustrated in Fig. 1 and 2. Fig. 1 shows a sketch of a zone containing salty connate water plus displaceable hydrocarbons, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 2 shows this zone, together with fluid content and resistivity graphs. after invasion by a fresh water mud. The resistivity pattern on moving away from the borehole is high: low: high. The absence of the low zone phenomenon in water zones is illustrated in Fig. 3 and 4. Fig. 3 shows a sketch of a zone containing salty formation water and residual oil, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 4 shows this water zone, together with fluid content and resistivity graphs, after invasion bv a fresh water mud. In this case the resistivity pattern on moving away from the borehole is high: low since there is no change in water saturation at the head ol

Jan 1, 1956

COLUMBIA LOCAL SECTION Executive Committee F. A. THOMSON, Chairman GEORGE W. RODDEWIG, Vice-Chairman L. K. ARMSTRONG, Secretary- Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. MCCAFFERY S. H. RICHARDSON The quarterly meeting of the Columbia Local Section of the Institute Was held in Pullman, Wash., May 16-17, 1914, as a joint meeting with the Spokane Sections of the. American Institute of Electrical Engineers and the American Society of Civil Engineers, each holding separate sessions on the afternoon of the 16th With a joint meeting in the evening. The Section meeting was held in Science Hall, the Chairman, Prof. Francis A. Thomson, presiding. E. Jacobs, Secretary of the Western Branch of the Canadian Mining Institute, acted as Joint Secretary: About 35 members and guests Were present. H. C. Bellinger, formerly Metallurgical Manager of the Great Cobar Co., Ltd., N. S. W., Australia, described the Horwood process. Papers as follows were presented and discussed: A Smelting Furnace for Cyanide Precipitate, by P. S. Anderson. Mining Methods in Rossland, by C. H. Loux. Geological Notes on a Part of Central Idaho, by Prof. D. C. Livingston. Some Notes on the Ore Deposits of Republic, Wash., by A. M. Balfour. E. Steidl, of the U. S. Bureau of Mines Rescue Car, spoke on the mine rescue service of the Bureau, and E. Jacobs described what is being done along similar lines in British Columbia and elsewhere. The evening was occupied in joint session, J. B. Fisken presiding. Mr. Fisken read a short paper on the benefit to the young engineer of an association y membership in the local section of either of the societies represented in the meeting, and C. F. Uhden gave a stereopticon lecture on Power Development Along the Spokane River.

Jan 7, 1914

By Hugh Archbald

IT is possible to construct a simple diagram of the earnings, or the production, of the men employed at a coal mine that will show not only if the conditions tend toward contentment among the men, but if the operating distribution of the work is correct. As earnings are the greatest cause of discontent, even exceeding all the other causes, if contentment exists in the matter of earnings, the likelihood of other discontents flaring up is greatly lessened. The basis of such a diagram would be the Gaussian curve of the normal variation in human ability. Such a curve has long been recog-nized. H. L. Moore,1 in discussing the quantitative relation between wages and ability says: "It has been pointed out that industrial efficiency is dependent upon physical, mental, and moral qualities, and these qualities . . . there is good reason for regarding as being distributed according to the Gaussian law..

Jan 7, 1924

By J. Vakili

The objective of this paper is to present a practical method for calculating minimum safety factors of rock slopes with a horizontal layer of weak material. It is demonstrated that the most critical failure surface, in this case, is a bilinear surface composed of a horizontal failure surface inside the weak layer and an inclined surface inside the rock. The model presented in this paper shows that with a good approximation, the change in slope for the bilinear failure surface may occur directly below the slope crest. This assumption simplifies the calculation of safety factors considerably, because the most critical failure surface is located directly, and the trial computations for a number of failure surfaces are not necessary. Special parameters involved in slope stability analyses of highwalls in open-pit mines are discussed and, by an example calculation, the applicability of this method is demonstrated.

Jan 1, 1985

By Joseph W. Mills

In 1956 the discovery of nickel on Jumbo Mountain, Snohomish County, Washington, focused attention on this part of the Cascade Range, far more renowned for its timber than for its mineral resources. Hand specimens assaying as high as 13 pct Ni encouraged Discovery Mines Inc. of Mount Vernon, Wash., to stake 12 claims in Township 31 North, Range 9 East of the Willamette Meridian. The property was leased to Climax Molybdenum Co. in January 1957. Trenching, sampling, and geologic studies were carried out during the late summer of 1957 when most of the snow had disappeared. Although the deposits are only about four miles south of the logging town of Darrington and about two miles, as the crow flies, southeast of the end of a good gravel road from that town, all camp supplies and equipment were air-dropped, owing to the extremely rugged nature of the terrain.

Jan 3, 1960

By High Archbald

It is possible to construct a simple diagram of the earnings, or the production, of the men employed at a coal mine that will show not only if the conditions tend toward contentment among the men, but if the operating distribution of the work is correct. As earnings are the greatest cause of discontent, even exceeding all the other causes, if contentment exists in the matter of earnings, the likelihood of other discontents flaring up is greatly lessened. The basis of such a diagram would be the Gaussian curve of the normal variation in human ability. Such a curve has long been recognized. H. L. Moore,&apos; in discussing the quantitative relation between wages and ability says: "It has been pointed out that industrial efficiency is dependent upon physical, mental, and moral qualities, and these qualities . . . there is good reason for regarding as being distributed according to the Gaussian law.

Jan 1, 1925

By C. H. Chou, A. Sauveur

The senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallo-graphic planes of the austenite grains.1 To quote: On cooling through the point As, at about 900° C, iron passes from the gamma condition to a new allotropic form generally designated as alpha. This transformation, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain

Jan 1, 1929

By C. V. Millikan

Production engineering has continued its rapid progress during the past year. Many engineering efficiencies long practiced in other industries are being rapidly accepted by the oil industry, and every branch of development and production work is undergoing study that is reducing the time and hazard in the drilling of wells even for greater depths, is securing better service from equipment, and is obtaining greater ultimate recovery from the reservoirs. Deviation of Drill Holes Deviation of drill holes probably has attracted greater and wider study than any other subject. Until about one year ago it had been given little attention. Some California operators knew the common magnitude of deviation, but Mid-Continent operators hesitated to believe that holes could be drilled so crooked. The great emphasis and publicity given to the seriousness of the problem resulted in the design of many instruments to record the deviation by chart or photograph. Instruments which would give the direction as well as deviation were not generally favored because of the grave fears of the legal complications which might result if the bottom of a producing well should prove to be on a neighboring lease. With all the instruments available for determining deviation, the use of etching on a glass bottle by hydrofluoric acid is still the most common method employed. The beneficial result of this earnest effort to drill straighter holes is proved by a comparison of deviation of wells completed recently with those completed over a year ago. The time of this change is arbitrarily taken as Jan. 1, 1929, as at that time the operators were aware of the deviation which usually occurred, and most of them were making some effort to reduce it. Table I shows averages of wells completed by several companies. Data on a few wells outside the greater Seminole area are

Jan 1, 1930

By C. H. Mahoney, A. L. Tarr, P. E. Le Grand

Magnesium, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, 0&apos; the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.&apos; Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point, It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-hearing group by raising the temperature of the melt after the refining treatment to some 250°C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730°C. (I350°F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (I600°F.) and 930°C. (1700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to &apos;solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.&apos; It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying Constituent—the binary alloy containing 1.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack

Jan 1, 1945

J. S. UNGER,*Pittsburgh, Pit., (written discussion?).-From the subject of the paper it is natural to expect that the data presented must be results secured from an open-hearth furnace working under normal conditions, but such is not the case, as the conclusions are based on the results of laboratory tests, which do not approach service conditions. The early basic hearths were made of burnt lime, then followed burnt dolomite, bricks made of calcined dolomite and a &apos;binder, usually tar, and finally magnesite bricks covered with a layer of sintered magnesite. When this material became scarce, special dolomitic refractories were used. In the summary, it is claimed that magnesite low in lime, or of greatest purity, ranks first in the resistance to slaking and to corrosive slags. It is well known that neither pure lime nor magnesia has much value as a refractory. By the addition f fluxes, such as silica and iron oxide, lime is rendered inert to slaking in the same way as are the special dolomitic refractories. An example on a large scale is the ordinary basic open-hearth cinder, produced every clay, which does not slake. Pure magnesia, regardless of the lime content, is not any better fitted for a refractory than pure lime. The pure natural varieties, such as Grecian or Washington magnesites, must be burnt with sufficient silica and oxide of iron to produce a satisfactory material. Grain magnesite, either artificial or natural, is, not used in burning in a hearth in the state in which it is received. To make a satisfactory hearth, it must be made more impure by adding about 20 per cent. of basic open-hearth cinder, otherwise it will-not remain in place.

Jan 5, 1919

By James C. Fulton

Since publication of the First Edition of "Basic Open Hearth Steelmaking," in 1944, this book has been a major reference on the subject of steelmaking. The Second Edition of 1951 was so fundamental that it has retained its general usefulness to the present date. However, recently some of the material has been updated in connection with the writing of a companion book, "Electric Furnace Steelmaking." The sponsor of these two books, the Physical Chemistry of Steelmaking Committee, has felt that the new material should be made equally available to purchasers of either book. Accordingly the subject matter of Chapters 14, 15, and 16 of this new edition is duplicated by corresponding chapters in "Electric Furnace Steelmaking." It was also recognized that the use of oxygen in the open hearth and in the new basic oxygen processes represents a major development that should not be omitted from any basic reference. Thus the major new feature of this Third Edition is the supplement on "Oxygen in Steelmaking." The cooperation of the Iron and Steel Division&apos;s Acid Converter and Basic Oxygen Steel Committee (now merged to form the National Open Hearth and Basic Oxygen Steel Committee) is specifically recognized. In addition to the authors of chapters listed elsewhere, it should be noted that Arthur B. Wilder was the Committee Chairman. Although the changes in the Third Edition are important, the Committee cannot overlook the classic character of the Second Edition. This edition was edited by W. O. Philbrook and M. B. Bever in collaboration with H. B. Emerick and B. M. Larsen. It is anticipated that the Third Edition will maintain the value of the book until the current rapid changes in all basic steelmaking processes stabilize themselves sufficiently to justify a complete revision of the entire text in Part I. The experienced service of Wesley Burr in incorporating the new material in the index is also recognized.

Jan 1, 1964

David H. Browne was born June 8, 1864; at Hollymount, County Mayo, Ireland. At the age of 16, after going through the Londonderry Academy; he came to this country, and entered the University of Michigan, where he was graduated in 1885. He began his scientific practice as chemist, under F. A. Emmerton, in the laboratory of the Joliet Steel Co., after which he served some time as chemist at the Ludington mine, Iron Mountain, Mich. But in 1888 he went back for a year to his alma mater as instructor in inorganic analysis. Those who knew him feel sure that he would have been an efficient and popular professor; but his ardent temperament could not brook the rnonotony and confinement of the class- room; and in 1899 he went to work at the Andrews and Hitchcock blast-furnaces, at Hubbard, Ohio, where he remained until 1891, when he entered as chemist the service of the newly organized Canadian Copper Co., operating in the Sudbury district, Canada. This was the beginning of his special professional life-work. For twenty-six years he devoted himself to the numerous and complex problems successively arising in connection with the metallurgical treatment of the nickel-copper ores of Sudbury. One of his notable achievements was the development of an electro-lytic process for the separation of nickel and copper in the ores referred to. This method was successfully employed for several years; but when the Canadian Copper Co. was absorbed by the International Nickel Co., the cheaper Orford process owned by the latter was substituted. . A still more permanently important piece of metallurgical progress credited to Mr. Browne was the successful firing of reverberatory smelting-furnaces with powdered coal-a measure which had been desired, dreamed and attempted by others, but which he was acknowledged as first to put in practice on a large scale. The Engineering and Mining Journal of April 7, 1917, says editorially of this improvement:

Jan 6, 1917

By R. W. Raymond

At the Pittsburg meeting of the Institute, in March, 1910, the death of Mr. Metcalf was announced, and Col. H. P. Bope, of Pittsburg, delivered in memory of him a brief but eloquent address, which, though expressing the Norrow of Mr. Metcalf&apos;s friends, and, in general terms, the debt of gratitude which his country and his profession owed to him, was not intended to be a complete survey of his life and work. With Colonel Rope&apos;s permission, and with the aid of some of the statements in his address, I substitute for it, in our Transactions, this more cletailed, yet still inadequate memorial. As Colonel Rope justly remarked, the men who could do justice to this theme—such men as Jones, Chalfant, Bennett, Oliver, and Park—passed away before Metcalf, leaving him almost the last of the generation of great steel-makers who made Pittsburg the Sheffield of America, and who discharged a double function, as the rearguard of the old metallurgical practice and the ran-guard of the new. I knew many of them; would that I were better qualified to celebrate their achievements. William Metcalf was born Sept. 3, 1838, at Pittsburg, Pa., where his father, Orlando Metcalf, was an eminent member of the bar. At the age of sixteen, he entered the Rensselaer Polytechnic Institute, at Troy, N. Y., from which he was graduated in June, 1858: Returning to his native city, he became an assistant engineer in the Fort Pitt Foundry, of which he was made Superintendent in 1859. This famous establishment produced the largest castings and heaviest machinery then knolrn in the United States; and Mr. Metcalf&apos;s intense, intelligent and incessant study of his business prepared him as a manufacturer for a patriotic service to his country more valuable than, as a soldier, he could have rendered in the field. The call came in 1862, when the government needed, above all things, a supply of field, naval and siege artillery. The

Jan 1, 1911

By W. L. Crentz, E. E. Donath, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom&apos;s paper can be written: Q Q = K D&apos;. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0&apos; " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By E. E. Donath, W. L. Crentz, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom&apos;s paper can be written: Q Q = K D&apos;. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0&apos; " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

A. L. BLOMFIELD, ? Colorado Springs, Colo. (written discussion?).¬I congratulate the author on bringing out a paper of real service to the profession. His contention of uniform size in balls is borne out by my own experience; in coarse crushing at the Golden Cycle in 6 by 6-ft. (1.8 by 1.8-m.) ball-mills we unquestionably gain by screening out the small balls once or twice a month. The point of gaging the ball size to be used by the uniformity of screen sizing is of particular interest. The necessity of sufficient return feed from classifier to the ball-mill is sound and clearly shown. In connection with this, I wish two further points had been gone into as thoroughly: (1) The effect of the quality of classification. In general, it is true that the smaller the per cent. of undersize in the feed the more effective is the mill&apos;s work. This is true on a bucking board, in tube-mills, ball-mills, and grinding pans. Given the possibility of returning. a full-feed load to any mill, it has been my experience that the effective work in the grinder is almost proportional to the quality of the return feed. (2) Again speaking generally, the shorter the tube-mill the greater is the quantity of return feed necessary to keep it loaded. The classification thus keeps the oversize in the mill more free from finished product and thus the crushing more efficient. It is very easy to overload any long mill with too much return

Jan 4, 1919

By E. L. Howard, R. S. Barney back

E. L. Howard (Chief Testing Engineer, Pacific Cement & Aggregates, Inc., San Francisco, Calif.) We have made concrete with all the materials mentioned by Mr. Barneyback, including sawdust. He has highlighted the principal problems and effects found when these light materials are used as concrete aggregate. We can only agree with the inter-relationship he has emphasized between grading, specific gravity and unit weight. Uniformity in these characteristics helps to assure good concrete. Mr. Barneyback says the design of lightweight concrete mixtures "is a complete mystery to most engineers". He is wholly right in his evaluation of our ability generally to put together a concrete using lightweight aggregate. A study of the references he has appended will yield little comfort in the matter of proportioning. Much remains to be done in this area of concrete. We believe Mr. Barneyback has treated the subject, though briefly, in an excellent manner.

Jan 1, 1965

By T. A. Wright

The sampling of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or (&apos;metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can be readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also. As a matter of fact, we may expect that improved refining processes will make possible the partial recovery of lead and tin which are now lost.

Jan 1, 1928

By M. Cohen, R. J. Teitel

There is considerable interest in beryllium because of its low density (1.84 g per cu cm), high modulus of elasticity (40 X 106 psi), high melting point (1280°C), and special nuclear characteristics. Moreover, it has fair resistance to corrosion and oxidation. However, the purest beryllium known to the authors is relatively brittle at room temperature, and cannot be fabricated readily. The search for improved properties leads naturally to investigations of beryllium alloys and the phase relationships upon which they are based. The present paper is concerned with the alloys of beryllium and iron, primarily from the standpoint of the equilibrium diagram. Iron was selected (1) because of its all-round importance in metallurgy, and (2) because the beryllium-iron system is known to be quite complex. The most recent diagram in the literature is that of Gaev and Sokolov,&apos; and covers only the iron-rich end up to 16 wt pct beryllium. Beryllium markedly restricts the austenitic field, closing the gamma loop at about 0.4 wt pct (3 at. pct). On the other hand, beryllium is soluble in a-ferrite up to a maximum of 7.5 wt pct (34 at. pct) at the eutectic temperature of 1160"C. The eutectic composition lies at 10 wt pct beryllium (42 at. pct) and corresponds to a mixture of or and FeBez (called j3 in the present paper). The solid solubility of beryllium in the a phase decreases with decreasing temperature, and makes precipitation-hardening possible. These findings substantiate the earlier work of Oester-held,2 Wever and Mueller3 and Laissus.4 In addition to the FeBe2 (ß) mentioned above, Misch6 has reported on FeBes, and indicated evidence for another compound containing still more beryllium. A preliminary diagram by Gordon,5 not hitherto published, is given in Fig 1. Besides the phases previously named, there are shown a solid solution of extended range (e), a compound of limited solubility (t), and a high temperature phase (7). Beryllium is designated as 8. The t field contains the compound composition FeBea, and the f phase undoubtedly corresponds to the beryllium-rich compound found by Misch.6 The region around the { phase was proposed by R. J. Teitel based on Gordon&apos;s data. The details of the diagram are self-explanatory. It was the unusual complexity of this system that prompted the authors to undertake the present studies. By the same token, more emphasis was placed on the beryllium-rich than the iron-rich end of the diagram. Exprimental Details RAW MATERIALS The beryllium employed in this investigation was one of the purest grades available. Its chemical analysis after vacuum melting is given in Table 1. The metal assayed 99.4 wt pct beryllium. Vacuum melted electrolytic iron of purity shown in Table 1 was the source of iron.

Jan 1, 1950