Search Documents

By M. C. Fuerstenau, J. D. Miller

The response of calcite to flotation with saturated fatty acids and alkyl sulfonates of various chain lengths is presented. The amount of collector re-quired for flotation is shown to decrease systemati-cally with increasing carbon content from 8 to 12-carbon atoms per molecule. This systematic flotation response is correlated with the solubilities of the calcium-collector salts, which were established with a nephelometer. The 14-carbon collectors deviate from this systematic behavior, and no flotation is possible with the 16-carbon homologs. As determined by infrared analysis, the mechanism of collector adsorption involves a specific chemical reaction be-tween the collector and the surface. A reaction of the form CaCO3(s)+ 2 RCOO"=*=Ca(RCOO)2(s) + C03= is suggested. The pH of the system is also shown to be a most important parameter as it controls the carbonate, calcium, and collector ion concentrations in solution and thus controls flotation response. The importance of hydrocarbon chain length of collectors was recognized early, and various studies have been made on this aspect of flotation. Wilkinson, ' for example, noted that as the chain length of alkyl xanthates is increased, the amount of collector required for flotation of sphalerite is decreased. The same effect has been shown in the flotation of galena.2 Similar results were obtained when malachite3 and calcite4 were floated with various fatty acids. DeBruyn5 has shown that a similar phenomenon occurs when quartz is floated with amines at constant pH. Recently, Fuerstenau, Healy, and Somasundaran6 correlated this phenomenon with the van der Waals cohesive free energy of association of the hydrocarbon chains. It seems unlikely, however, that chain association could be involved in the sulfide and carbonate systems with the collector additions employed, especially with the short-chain xanthates. Rather, it would seem that the decrease in collector concentration with increase in chain length noted for flotation is related to the solubility of the metal-collector salt. The purpose of this investigation is to verify this premise and also quantify this phenomenon if possible. Calcite was selected for study with both alkyl sulfonates and saturated fatty acids as collectors. EXPERIMENTAL MATERIALS AND METHODS The collectors used in this investigation ranged from 8 through 14 carbon atoms per molecule. The fatty acids had a reported purity of greater than 99%. The sodium alkyl sulfonates were provided by the Marathon Oil Cot, Littleton, Colorado, and had the

Jan 1, 1968

By Cyril Wells, Robert F. Mehl

The purpose of this investigation was to prepare high-purity iron-carbon alloys, to determine as precisely as possible the A3(GOS), the Acm(SE), and the A1(PSK) transformation temperatures in the meta-stable iron-iron carbide system (up to 1.4 per cent C), and to study the influence of carefully controlled and constant rates of heating and cooling (1/8 to 2o C. per minute) upon the transformation temperature and upon the resulting microstructure. Apart from the general metallurgical importance attending the completion of such a task, it will be noted that highly precise transformation temperatures are of interest and importance in the thermodynamic study of this system1. Several determinations of the iron-iron carbide diagram have been made2. These suffer generally from the low purity of the alloys used, and from the application of methods of investigation of low sensitivity. Attempts to compare and weight the many data available in an effort to construct as accurate a diagram as possible have, in the main, been unsuccessful. In general, the wide differences in the results of different workers, the lack of complete analytical data, the omission of important details relating to the heat-treatment of the alloys, and the meager description of the methods of investigation applied, render such a process of averaging nearly meaningless. It may be seen from the summaries by Epstein2 and Körber and Oelsenl that variations as great as 30' C. exist in the reported data on the A3 temperatures in iron-carbon alloys. Fortunately, the Aa temperature in pure iron is now known to be 910" C. ± 1° C.3 The best recent work on iron-carbon alloys is that of Esser4 on hypoeutectoid steels and that of Sato5 on both hypoeutectoid and hyper-eutectoid steels. Esser made a dilatometric and magnetic study of iron and iron-carbon alloys containing 0.06 to 0.86 per cent C, for which a high purity is claimed. Presumably the electrolytic iron was reasonably pure, but the alloys contained considerable impurities, on the average totaling 0.35 per

Jan 1, 1937

By C. A. Heiland W. E. Pugh

The principle underlying the majority of magnetic intensity variometers is a comparison of the force to be measured with another force of known magnitude. The known force may be (a) of a magnetic nature, such as magnetic fields produced by magnets or coils, or (b) of a mechanical nature, such as (1) the elastic forces of wires, or (2) the force of gravity, such as employed in bifilar magnetometers and magnetic balances. In instruments of such type, usually a magnetic system is employed, free to move about either a horizontal or vertical axis, on some sort of a suspension. If the earth's magnetic field alone were present, such a system would adjust itself into the direction of the field or that of its components. Owing to the simultaneous action of the comparison force, however, the magnetic needle assumes a position that differs from the direction of the magnetic force; for all such instruments, the angle of deflection is given by tan = FIX, where F is the known and X the unknown earth magnetic force component. In other words, the magnetic system merely serves as an "indicator" for the position of balance of the two forces. Considering the matter from this point of view, it is not immediately obvious why the temperature of such a magnetic system should modify the results. In magnetic instruments, we may distinguish two different effects of temperature: (1) a magnetic effect and (2) a mechanical effect. The first is due to the fact that the magnetic moment of a magnet drops with an increase in temperature. This drop is characterized by the temperature coefficient of the magnetic moment (see equation 1). The second effect is due to the change in the torsion of suspension wires with temperature or to the expansion of lever arms of masses acting on magnetic balances.

Jan 1, 1934

By H. G. Moulton

THE INCREASING scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth

Jan 2, 1920

By R. W. Kraft

A back- reflection precession-type X-yay camera for determining the crystallographic orientation of the crystallites of both phases in small areas of thick specimens of polyphase alloys is described ad the geometry, advantages, and limitations of the apparatus are discussed. Metallographic obseg-vations of interfacial angles (or habit planes or growth direction are made on the same specimen so that the crystallographic and metallographzc orientation data call be directly correlated. An example of the application of tile technique to a unidi-~~ectionally solidified CuA12-A1 eutectic specimen is presented. The interfacial planes ad growth directions of each phase were established, and the orientation relationship between the phases was observed and found to be approximately intermediate between two previously reported relationships. The crystallographic interfacial relationship between two solid phases is an important parameter in a variety of metallurgical phenomena because of the energy associated with the interface and because this energy is at least partly associated with the way in which the two space lattices are in contact along the interface. In order to describe the interfacial planes in the crystallites of both phases it is necessary to determine the crystallographic orientation of each phase in a specimen relative to each other, and to directly correlate these data with met-allographic measurements from which the interfacial planes can be determined on the same specimen. The back-reflection Laue technique is the easiest way to determine the orientation of thick single crystals or large grains and the method can be combined with metallographic techniques to provide the necessary data, provided the reflections from each phase can be distinguished from one another. However, if the crystallites are small or of varying orientation or if one or both phases has a unit cell with less than the maximum symmetry, many overlapping and complex Laue patterns are recorded simultaneously and it becomes impractical if not impossible to interpret the photographs. All of these complexities were present in a unidirectionally so- lidified A1-CuA12 eutectic alloy1 for which a crystallographic analysis was desired. Consequently the method described here was developed since no known X-ray or electron diffraction technique had all of the following attributes which were required. 1) Method should yield data from which the crys-tallographic orientation of every crystallite or diffracting unit in the irradiated area can be determined. 2) Method should be adaptable to the study of small areas. Depending upon the degree of preferred orientation in the specimens, it should be possible to obtain reliable data in a reasonable length of time on irradiated areas as small as 1.0 or even 0.1 mm in diam. 3) Method should permit direct correlation of crystallographic data with microscopic orientation data pertaining to crystallite axes, habit, morphology, and growth directions as determined by optical microscopy. 4) method should be such that selected areas of large specimens can be easily studied. Trepanning of a small specimen (such as an electron microscope specimen) from larger specimens was undesirable since it would greatly increase the problem of correlating the crystallographic and microscopic directional data. Requirements 3 and 4 dictated that an X-ray back-reflection pinhole technique should be used on large samples, such as metallographic specimens which had previously been examined and analyzed for their microscopic characteristics. Similarly, requirement 2 could be satisfied by choosing a collimator of appropriately small diameter. Exposure times would not be excessive provided the detector were close enough to the specimen. Because of space limitations film was chosen in preference to a Geiger counter. Requirement 1 was fulfilled by using monochromatic radiation and providing enough additional degrees of freedom in specimen rotation to compensate for Bragg law restrictions on diffracted beams. DESCRIPTION OF APPARATUS The apparatus shown in Fig. 1 consists of a pin-hole collimator, (a), projecting through a rotatable circular film in a holder, (b), which records X-ray reflections in the back-reflection region. The specimen, (c), is mounted on the end of a shaft, (d), which is provided with an adjustment, (e), so that the specimen surface can be placed accurately on

Jan 1, 1962

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By Claudio Gutiérrez

The action of quebracho in the selective flotation of fluorite and calcite has been studied. It has been found that the unavoidable ions produced by dissolution of these minerals can precipitate calcium oleate which profoundly influences the adsorption of oleate. The depressing action of quebracho is due, at least partly, to a decrease of the oleate adsorption. The depression of flourite flotation by quebracho in the presence of calcium is due to the fact that precipitated calcium oleate can become only physisorbed, its adsorption being strongly prevented by quebracho. It is concluded that adsorption experiments with flourite must be conducted with a flotation-size mineral, which has a lower dissolution rate than when finely ground.

Jan 1, 1980

By G. R. Hodgson, M. P. Lebourg

The introduction in the field of a new type well completion called for the setting of tubing open-ended in the well before perforating the casing. This paper describes a new perforating tool of the shaped charge expendable type, small enough to pass through tubing and powerful enough to perforate the casing. The perforations are produced at an angle and are large enough for optimum production. Performance of this tool in targets and under various well conditions is described. Very often no lifting equipment will be available at the well. In some cases, pressure will exist in the well at the time of the perforating operation (workover wells or multiple trip perforation) ; therefore, new equipment and new technique for the perforating operation were devised. This paper describes this equipment and technique, particularly casing collar recording, sheave support, and cable pull-down device. this last item being necessary for wells under pressure. Results obtained with this tool in the field are given. INTRODUCTION One of the key requirements for the introduction in the field of a new method of permanent well completion was the development of a new perforating method involving the use of a perforating gun small enough to go through tubing and with enough penetrating power to perforate the casing satisfactorily. The equipment described in this paper was basically designed to go through open-ended two-in. tubing and to perforate 5 1/2 in. casing. The equipment is illustrated in accompanying figures. NEW COMPLETION METHOD With the new permanent type well completion, the production string of casing is run and cemented through the potential producing zone. Open-ended tubing is -then run into the well and used to replace the drilling fluid with oil or water. The amount of the oil or water "cushion" can be varied according to the expected bottom hole pressure. Thus, if desired, the hydrostatic head can be greater, equal to, or less than the expected pressure within the zone to be perforated. Mud having been displaced, the tubing is -then positioned so that the end is above the zone to be perforated. The Christmas tree and flow lines are installed and tested. The drilling rig can now be removed from the well since it is not necessary for the perforating operation, thus resulting in a saving in rig tme. The perforating equipment is then moved to the well and the gun lowered through the tubing. After the gun passes out of the open end of the tubing, the depth measurements are correlated with casing collars and the gun placed opposite the zone to be perforated. Upon firing, the gun body is shattered and falls to the bottom of the well. Since the lubricator has been closed before firing, it is possible to withdraw the casing collar locator and head and then open the well immediately to the tanks. DESCRIPTION OF GUN An investigation of two basic types of Perforators, namely a bullet perforator and a shaped charge gun, was undertaken towards the development of a gun to meet the aforementioned requirements. Preliminary tests on various bullet perforator designs within the diameter limitations did not give results encouraging enough to warrant further study. Somewhat better results were obtained by using conventional shaped charges; but, as in the case of the bullet types, the necessarily small overall diameter proved to be a severe limitation and resulted in insufficient penetration. A shaped charge employing a new design was developed which gave excellent penetration. These shaped charges were designed to produce a large hole directed upward at a 45" angle. In order to obtain the maximum space possible for these charges, it was decided to use an expendable carrier made of drillable material, usually aluminum, which would shatter at the time of firing, leaving only harmless fragments at the bottom of the hole. The fixed spacing is five shots per ft. wit11

Jan 1, 1952

By S. B. Christy

The fact that many millions of gold have been extracted by the cyanide process, during the last five or six years, from South African tailings which could not be profitably worked by any other method previously tried upon them, lends a peculiar practical interest to this branch' of metallurgy. Numerous writers have recently made valuable contributions on the process without exhausting the many complexities of the subject. Among the first American writers on the subject in its modern aspect were two former students of the University of California, Mr. Louis Janin, Jr., and Mr. Charles Butters. Young Janin was one of the first to enter this field, and performed much useful experimental work in the early stages of the history of the process. At about the same time, Mr. Charles Butters, who had left California to erect chlorination works for the Robinson mine at Johannesburg, became interested in the cyanide process, and, after getting the chlorination plant in working order, put up, for working the tailings from the Robinson mine, a cyanide plant which achieved the first large-scale success ever made with this process. The papers which Charles Butters, together with John E. Clennell and Edgar Smart, have contributed on the chemistry of the process, were among the first to give any adequate idea of its nature.* Another important contribution to the literature of the subject is the paper of Dr. A. Scheidell, published in 1894 as a " Bulletin of the California State Mining Bureau." This contains an admirable summary of the state of the art at the time of its publication.

Jan 1, 1897

By I. Iwasaki, K. Adam

During wet grinding the electrochemical interactions between grinding media and pyrrhotite not only accelerate media wear but also adversely affect the suede mineral's flotation response. A possible remedy of the adverse effects on floatability by applying electric potentials to grinding media was examined. Flotation tests, Auger electron spectroscopy, and X-ray photoelectron spectroscopy were used to study pyrrhotite surface properties. Although anodic polarization of the steels increased metal loss by corrosion, pyrrhotite flotation recovery was increased. In the case of cathodic polarization, flotation recovery improved somewhat in a narrow range of overpotentials. At higher cathodic overpotentials, however, mineral floatability was progressively lowered although the corrosive wear of grinding media might be reduced.

Jan 1, 1985

By P. D. Frost, H. A. Robinson, J. R. Doig, M. W. Mote

The mechanism of hardening in heat-treatable zirconium alloys was foUNd to be analogous to that for titanium alloys. Zirconium containing a relatively large addition of a ß -stabilizing element such as molybdenum or columbium can be hardened by the following transformation: Lean alloys, having insufficient alloy content to retain ß at room temperature are hardened by the following transformation: Application of these findings in Zr-Mo-Sn and Zr-Nb-Sn alloys produced strengths as high as 190,000 psi with reasonable ductility. PRIOR research on zirconium alloys has been concerned with development of greater strengths and creep resistance by solid-solution hardening or by dispersion hardening. Although solution and aging heat treatments had been applied earlier to zirconium alloys, quenching frequently produced low ductility. The possibility that the ß-to-w transformation, discovered earlier in titanium alloys,' might also occur in zirconium alloys and cause low ductility was considered, and, indeed, was found as predicted2 to be the case. In the earliest experiments, the heat-treatment response of titanium, too, was disappointing. However, by avoiding the formation of the embrittling w phase, it became practical to obtain room-temperature strengths higher than 180,000 psi, with elongation values of 10 pct.3 Based on the present concept of titanium heat treatment, the principal requirement for a heat-treatable zirconium alloy is that it contains a certain minimum amount of one or more ß -stabilizing elements. Only molybdenum, columbium, and tantalum, when present in sufficient amounts, are known to stabilize ß zirconium to room temperature during rapid cooling from the ß field. Tantalum was undesirable because of its high thermal-neutron cross section. Aluminum and tin are effective a stabilizers, but aluminum has been shown to seriously decrease the corrosion resistance of simple zirconium alloys in hot water. Therefore, for the present study, tin was used as the stabilizer addition. The alloys selected for this evaluation are presented in Table 1 along with their analyses and ß-transus temperatures. The analyses indicated that intended compositions were usually realized. EXPERIMENTAL PROCEDURES All of the alloys were melted from sponge zirconium and fabricated to sheet for heat treatment

Jan 1, 1960

By Frank Clemes Smith

The study of the so-called refractory gold-ores of the Potsdam sandstone, ores which are probably of wider occurrence and of much greater economic importance in the Black Hills than is generally supposed, has led the writer to formulate in the present paper some of the results obtained in the course of a special examination of these particular ores, conducted at the State School of Mines at Rapid City, So. Dak. Various circumstances have interrupted the work, and it will easily be seen that relatively little has yet been accomplished; but it is hoped that this little may be of sufficient interest to justify a later supplement. Tellurium, discovered by Muller von Reichenstein in 1781, is generally classed as a very rare metal; it is further mentioned by one of our late writers as " of comparatively little importance," and as obtained from its ores by a " complicated process.'' Concerning its rarity, we have some trustworthy evidence below. Its commercial importance, particularly in connection with electrical appliances, has been passed upon by Mr. Edison ; * and it is certain that, in some metallurgical processes for the treatment of gold- and silver-ores, it may be saved as a byproduct at a relatively reasonable expense. The importance of tellurium as a mineralizing agent is emphasized by the remarks of one of our leading metallurgists,jwho, in his own practice and by a wide series of experiments, has found its occurrence to be much more general than has been supposed. Recently the same writer has discussed the occurrence of tellurides and oxidized tellurium compounds in the gold-ores of Cripple Creek, Colo., and in those of the Black

Jan 1, 1897

By H. M. Chance

The Taviche district is about 12 miles from the town of Ocotlan in the State of Oaxaca, and about 250 miles south of the City of Mexico. Its altitude rises to something more than 5,000 ft.; and although within the tropics (latitude about 17° N.) the climate is mild and salubrious, neither excessively hot in summer nor cold in winter. The phrase, "perpetual spring," which has been applied to it, aptly describes the weather during my stay. Sugar-plantations, bananas and other tropical and semitropical fruits flourish in the valleys, while the hills

Jan 1, 1905

By J. W. Hickman, E. A. Gulbransen

In a previous paper' the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300' to 7o0°C. except for copper, wherc the range selected was 100' to 500°C. The results of these studies were presented in graphical form as existence diagrams of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviatiois in lattice Darameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: 1. The existence diagrams of various alloys. 2. The effect of the structure of the alloying metal on the existence diagram of iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body-centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K4²B, Nichrome V, Hipernik, Inconel, Stellite "²I," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

In a previous paper' the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300' to 7o0°C. except for copper, wherc the range selected was 100' to 500°C. The results of these studies were presented in graphical form as existence diagrams of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviatiois in lattice Darameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: 1. The existence diagrams of various alloys. 2. The effect of the structure of the alloying metal on the existence diagram of iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body-centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K4²B, Nichrome V, Hipernik, Inconel, Stellite "²I," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1947

By Ford R. Bryan, Edward F. Runge

BECAUSE of the need for ductile heat resistant alloys of non-strategic composition, there has been metallurgical development of Fe-A1 alloys possessing improved ductility and hot strength, together with high oxidation resistance. Iron and alu- minum form solid solutions up to approximately 35 pct Al. Alloys in the 8 to 12 pct A1 range are characterized by excellent oxidation resistance, high electrical resistivity' and, when appropriately alloyed, have creep rupture strength equivalent to that of the austenitic stainless steels.' At higher aluminum levels, the magnetic properties are of considerable interest. Nachman and Buehler" have recently reported on the desirable magnetic characteristics of the 16 pct alloy.

Jan 1, 1957

By A. A. Bauer, M. S. Farkas, F. A. Rough

An investigation of the d-phase relationships between the uranium-zirconium and uranium-molybdenum systems was conducted. A ternary cut joining U-31.5 at. pct Mo to U-74 at. pct Zr is presented on the basis of differential thermal analysis, metallographic and X-ray diffraction data. HyDothetical isothermal ternary sections, inferred from the determined d-phase relationships, are presented for the uraniztm-zirconium-molybdenum system. A ternary eutectoid, at 454ºC, was found in zirconium-rich alloys. Its composition, based on metallography and electron-beam micro-analysis, is estimated as U-61.7 at. pct Zr-7.1 at. pct Mo. URANIUM binary systems have been studied extensively in the past to supply basic information needed in reactor-fuel development. Alloys of uranium with zirconium, molybdenum, and titanium are of particular interest because, in these binaries, extensive or complete solid solubility between the body-centered-cubic forms of these elements and y uranium exists. In addition, an intermediate phase of limited solid solubility forms in each of these systems by transformation of the high-temperature ?-uranium phase. Previous investigation of the phase relationships existing between the intermediate 6 phases in the uranium-zirconium-titanium and the uranium-molyb- denum-titanium ternaries have already been reported.1,2 The results of an investigation of the phase relationships existing between the 6 phases in the uranium-zirconium-molybdenum system is reported here. The phase equilibria that occur in the solid-state portions of the pertinent binary systems are shown in Fig. 1. Phase nomenclature appearing throughout the report is as shown in these diagrams. The crystal structure of the phases in this system are given in Table I. EXPERIMENTAL PROCEDURES Alloys were cast and fabricated to 1/4-in.-diam rod. Specimens were heat treated and examined by metallographic and X-ray techniques. Thermal-analysis data were obtained.

Jan 1, 1960

By E. V. Potter, E. T. Hayes, H. C. Lukens

LARGE volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that ignite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.1.2 The close relationship between iron and man¬ganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. APPARATUS The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of I00 c.c. for a 60-cm. length. For larger changes in gas volumes; auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945

By Guy W. Jordan, David P. Hale

High-iRon cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper"burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to"freezing and thawing, and increases the resistance of the cement to sea "or sulphate waters. [" During the past few years the construction of numerous dams through- "out the Southeast by the Tennessee Valley Authority has stimulated the "production of high-iron cements. At present a great number of specifica- "tions call for an iron cement, and the industry is supplying this demand "with a Portland cement carrying approximately 5 per cent iron oxide. "Several manufacturers are now making practically all of their cement "of this type and a number of others manufacture it as a special cement "over short periods to meet demands from the Tennessee Valley Authority "and other buyers. " The recent increase in the use of iron in Portland cement has created "a market for iron products that previously was nonexistent. The chief "sources of supply for the cement manufacturers at present are iron sand, "iron sinter and slag, and ocher. The Copperhill mining district, Ten- "nessee, supplies both iron sinter and slag for use in cement. The Carters- "ville district supplies iron sand, ocher, and some iron resulting from the "magnetic separation of iron from barite. The advantages of these "products vary according to the chemical properties of the raw materials "and the methods of handling used by the different manufacturers. Where "the iron is to be handled by conveying belts and in hopper cars, the iron"sand and sinter and slag are preferable. Where the silica content must "be raised, the iron sand is doubly advantageous because it supplies both

Jan 1, 1942