Search Documents

By Nathaniel Arbiter

THE separation of minerals by flotation can be regarded as a rate process, with the extraction of any one mineral determined by its flotation rate, and the grade of concentrate by the relative rates for all the minerals. So regarded, the significant variables for the process are those that control the rates. These variables are of two types, the first describing the ore and its physical and chemical treatment prior to flotation and the second characterizing the separation process in the cells. This paper will examine the variation in rates for a group of separations, will show that a simple rate law appears to govern, and will consider the relation of the control variables to the rates. The use of rate constants for evaluation of performance and efficiency will be discussed.

Jan 9, 1951

By R. W. Smith, Z. Sadowski

The stabilities of finely divided mineral suspensions were determined as functions of pH and concentrations of polyethylene oxide, sodium ligninsulfonate, sodium dodecybulfate, and sodium oleate. In addition, the electrokinetic potentials of the minerals were determined under identical pH and additive concentration conditions. Flocculation or dispersion of the suspensions is discussed in terms of both the amount and manner of adsorption at the appropriate solid-liquid interface as it is influenced by additive concentration and pH.

Jan 1, 1986

By G. W. Tracy, R. D. Carter

Numerical calculations were made to determine the behavior of reservoirs with high-pressure drawdown and wide well spacing where the initial productivity is low and the wells are completed by hydraulic fracturing. The two-phase flow equations were solved for the flow into a single well. This well was assumed to be producing from a reservoir with hydraulically created horizontal fractures (four different systems with fractures were studied). For comparison purposes, additional two-phase flow calculations were made assuming a reservoir with uniform rock properties. The two-phase flow results were also compared with the conventional calculation methods, which do not include the effect of saturation gradients resulting from a simultaneous flow of oil and gas which are normal to this type reservoir. It was found that the conventional methods predict (1) a high and too optimistic value of ultimate recovery, (2) a high producing rate and a high reservoir pressure at a given oil recovery and (3) a low trend of gas-oil ratio with oil recovery. Included in the two-phase flow calculations were provisions to control the oil production rate by an allowable rate and, also, by a gas-oil ratio penalty rule. For the systems with hydraulic fractures, the producing rate was controlled by the gas-oil ratio penalty rule for most of the life. This is in contrast to the system with uniform rock properties which went "on decline" almost immediately. An unexpected characteristic of the systems which included fractures was the early rise in producing gas-oil ratio from 730 cu ft/bbl to approximately 1,200 cu ft/bbl, followed by a "leveling off" before the normally expected gas-oil ratio rise began. Additional features which are a result of hydraulic fracturing are (I) greater ultimate recovery, (2) higher average producing rates and (3) a lower average reservoir pressure at a given oil recovery. INTRODUCTION Some oil fields discovered during the past few years are producing from certain volumetric ally controlled reservoirs (often referred to as solution or internal gas- drive reservoirs) which are characterized by high-pressure drawdown at the wells. Since the available pressure drawdown at a well is limited by the static reservoir pressure and the producing rate is controlled by the available drawdown, wells completed in this type of reservoir usually produce at a rate less than the allowable from the time of completion. Because of this, this type of reservoir is referred to as a low productivity reservoir. Economic considerations require the use of wide well spacing and well stimulation by hydraulic fracturing to make commercial wells in this type of reservoir. Performance predictions for volumetrically controlled reservoirs have been made using a combination of two standard equations. 1. The "Schilthuis" or "Muskat" type material balance equation is used to relate the average reservoir pressure and the cumulative oil recovery. 2. The results from the material balance equation and the productivity factor as described by Pirson' are used to relate the cumulative recovery with producing rate and time. The material balance equation assumed uniform pressure and liquid saturation conditions throughout a reservoir. The steady-state radial flow formula allows for a pressure gradient toward a well but assumes uniform liquid saturation. These calculation methods are adequate for application to reservoirs wherein the drawdown at the well to realize satisfactory producing rates is small compared to the total pressure. In low productivity, volumetrically controlled reservoirs, the pressure drawdown at the well is large cornpared to the total pressure. Although a precise number cannot be given for the magnitude of a large pressure drawdown, values in excess of 1,000 psi would definitely be included. For practical considerations, this usually occurs when the formation flow capacity is less than about 100 md-ft. However, this limit of formation flow capacity will vary with the well producing rate. The low pressure in the neighborhood of the well which results from a high drawdown causes evolution of large volumes of gas. This causes the gas saturation to be higher near the well than at a greater distance—-hence, a non-uniform gas saturation. Also, the relationship between the relative permeability to oil (K/K) and gas saturation is nonlinear but decreases approximately in an exponential way with increases in gas saturation. Because of this, the following chain reaction is established.

By H. J. Gluiskoter

The chlorine content of the coals in the Illinois Basin ranges from 0.00% to more than 0.60%. The chlorine content of the Herrin (No. 6) Coal has been mapped on a regional scale and, in general, increases with the depth of the coal. The depth-chlorine correlation exists because the coal is in apparent equilibrium with the composition of the ground water associated with it, and the salinity of the ground water generally increases with depth. At least part of the chlorine can be easily removed from the coal in the laboratory. In a natural weathering experiment, chlorine values decreased markedly during an 8-week period. Results to date indicate that none of the coals studied has a sufficiently high chlorine content to make it unusable in high-temperature steam boilers, although special steps may be necessary in the preparation or utilization of some of the highest chlorine coals. Investigations into the occurrence and distribution of chlorine in Illinois coals have been in progress at the Illinois State Geological Survey for over 35 years. Since 1948, chlorine analyses of face channel samples and of drill core samples of coal have been made routinely. The increased interest in chlorine and alkalies in coal in the U.S. followed that in Europe, where power plants during World War II were called upon to produce at higher levels than previously and with less down time for maintenance. Higher steam temperatures were reached, resulting in increases in the amount of fouling of external heating surfaces and in corrosion of boiler tubes when high chlorine coals were used. Early studies of the problem showed that coals with high chlorine content were more likely than those low in chlorine to cause difficulties in installations fired with powdered fuel. Crossleyl reported that the first rule of thumb developed for British coals was that coals considered to be high in chlorine (more than 0.30%) caused the most trouble, those intermediate in chlorine content (0.15% to 0.30%) were less likely to cause difficulties and those low in chlorine (less than 0.15%) generally were not associated with alkali bonded deposits and corrosion. However, this relatively simple picture was not adequate to characterize the difficulties that could be expected during the utilization of a large number of coals and Crossley1 developed another scheme for assessing the chances of superheater corrosion. This scheme took into consideration the observation that coals high in sulfur as well as chlorine are more likely to cause corrosion and fouling than coals low in sulfur and high in chlorine. Crossley also considered the ash content. When two coals had the same chlorine and sulfur contents, the one with the greater amount of ash would be the less likely to cause difficulties. Knowing only the amount of chlorine in a coal obviously will not give all the answers. Indeed, the significance of the chlorine content has been much discussed and it has been suggested that perhaps the total alkalies are a better indicator of possible troubles. The observation that the deposits that form

Jan 1, 1968

By E. P. Pfleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed pressure, see Fig. 2. The

Jan 1, 1952

By F. M. Lyon, F. J. Chernosky

Research efforts have not developed techniques for the complete desulfurization of coal that is needed to reduce air pollution caused by burning coal and to reduce the sulfur in metallurgical coke. Sulfur in coal occurs in three forms and of these, the pyritic sulfur occurs as discrete mineral particles and, at least theoretically, should be subject to physical rejection. Pyrite occurring in hard rock mining is concentrated by froth flotation; therefore, the possibility of removal of pyrite from coal by flotation does exist. With this possibility in mind, the flotation and adsorption characteristics of ore and coal-pyrite were compared while using potassium ethyl xanthate as the collector.

Jan 1, 1973

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By Arthur F. Colombo

The selective - deslime - flotation process developed by the Federal Bureau of Mines as part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs is described. The operating parameters for the selective flocculation - cationic flotation of oxidized taconites from the western Mesabi range in Minnesota are discussed. Data from the operation of a 410 kg/hr (900 lb/hr) pilot plant employing reclaimed water are summarized for 2 types of oxidized taconites.

Jan 1, 1979

CONTENTS PAGE WARNER, ROBERT K.-Efficiency of Screening. Discussed by Robert C. Canby,Robert K. Warner, W. 0. Borcherdt, V. E. Flanagan 1 FAHRENWALD, A. W.-Surface Reactions in Flotation. Discussed by Arthur F. Taggart, A. M. Gaudin 7 Efficiency of Screening Discussion of the paper of ROBERT K. WARNER, presented at the New York Meeting, February, 1924, and issued, as Paper No. 1293-M, with MINING AND METALLURGY, January, 1924. ROBERT C. CANBY, Wallingford, Conn.-On page 2, the author speaks of the importance of using a testing sieve clothed with the same material as the screen being studied; does he regard this as essential? In practice, how does the screen efficiency calculated by the difficult-grain method compare with those computed by the usual undersize method? Is it possible by the author's method, to obtain a measure of efficiency that can safely be compared with that of another screen sizing a different ore? ROBERT K. WARNER.-The use of a testing sieve clothed like the mill screen being studied is desirable but not essential for routine work about a mill where the character of the feed varies little, as regards the shape of the grains and the sizing test. Close agreement in size of aperture between the sieve and the screen is, however, important if the data obtained are to be valuable to others working on a different feed. If the testing sieve is coarser than the mill screen, the efficiency will appear unfairly low; whereas if it is too fine one might get efficiencies greater than 100 per cent. because of the apparent oversize in the undersize. In either of these cases the usefulness of the difficult-grain method of calculation would be reduced. As screens wear, the undersize grows appreciably coarser so that it is desirable to test screens only when the cloth is new or else to provide testing sieves that are worn about the same amount. The futility of making efficiency observations on a. distorted or broken screen surface is obvious.

Jan 6, 1924

By Franklin Bache

There seems to be in the public mind, and even in the minds of some coal-operators not experienced in mines subject to dust-explosions, a feeling that there has been somet-hing mysterious at the bottom of a number of recent American colliery-exploaions. It has been declared in cases of accidents in mines regarded as particularly well equipped, in which every preventive precaution was said to have been taken, that the explosions were incomprehensible, and resulted from causes beyond the present knowledge of the practical coal-operator. But it is safe to say that no explosion has taken place which could not be explained by reasons well understood by most operators. The U. S. Geological Survey Testing Laboratory, recently inaugurated at Pittsburg for the reported purpose of investigating scientifically the matter of explosions in mines, will discover no new explanation of explosions. It can, however, co-ordinate the previous investigations of similar boards in England and on the Continent; and it may do a vast amount of good by promulgating widely, and in a form comprehensible to the most unlettered miner, certain facts and obvious deductions that cannot but have an effect in reducing the number and extent of the mine-disasters which, in the last few years, have been so terrible in frequency and magnitude.

Jan 1, 1910

By George W. Lower, William A. Hockings, Donald A. Kaczynski

The rate of dissolution of polycrystalline metallic copper in aqueous cupric ammonium nitrate solutions in the non-film-forming region was investigated by the rotating disc method. The investigation was performed in solution concentration ranges applicable to hydrometallurgical processes. This investigation was an extension of a study on the cupric ammonium carbonate system previously reported by Smith, Lower and Hockings, in which the following kinetic model was proposed: (1) Diffusion of cupric ammine ions to the copper surface; (2) Forward reaction - first order reaction of cupric ammine ions with metallic copper; (3) Reverse reaction - disproportionation of cuprous ammine ions to metallic copper and cupric ammine ions ; and (4) Diffusion of cuprous ammine ions from the copper surface. The nitrate system was selected for this study because it simplified the determination of the ionic composition of the solutions. The variables studied were stirring speed and cupric, ammonia, and nitrate concentrations. The dissolution rate increased linearly with at low values of but exhibited increasingly negative deviations from linearity at higher values of m. The rate also increased with increasing cupric concentration but decreased with increasing ammonia and nitrate concentration. Good agreement was obtained between the experimental rate data and the proposed model. Further verification of the model was indicated by the close agreement of the diffusion coefficient calculated from the data and comparable literature values.

Jan 1, 1974

By Daryl R. Tweeton, Jerry R. Riding, Grant Buma, Frank J. Rosswog

In situ solution mining of uranium has environmental advantages over conventional mining. The leaching of uranium, however, alters the ground-water quality in the aquifer where the mining occurs. Currently, regulations require that the ground water be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring ground-water quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By W. F. Boericke

The character of the Wisconsin orebodies must be clearly understood to appreciate the difficulties encountered in sampling and estimating them. Unlike the western vein deposits, they do not lie between regular walls, but form large, often highly irregular bodies, on a single floor in the so-called Galena limestone. The bottom of the ore is nearly always on the clay bed (a flat generally well-defined clay seam a few inches thick) which marks the junction of the base of the Galena lime and the top of the next formation, the Trenton lime. Above the clay bed, the orebodies make the unique pitch and flat formation described by Chamberlin.' Theoretically, we should find two pitches, one on either side of the top crevice, diverging as they go down, with the final flats a considerable distance apart on the clay bed. The area between, known locally as core ground, should thus constitute a single defined orebody, with the richer portions near the pitches and the leaner portion in the center of the core. Practically, we find few examples of this perfect orebody. Almost invariably one pitch is better defined than the other, and often the opposite pitch is marked only by a faint line of fracture showing stronger mineralization than the wall rock, or it may be totally lacking. But with an orebody of any size or richness, at least one strong pitch usually tends to follow an east-west trend, or a quartering course. Late mining developments in the rich New Diggings field indicate that these pitches often assume a horseshoe or crescent shape, the richer ore being in the heart of the crescent and the pitches showing less mineralization as they extend outwards. In the northern end of the field, on the contrary, the pitches maintain generally a consistent direction, and have been mined for thousands of feet from the shaft. The length of the orebody may be several thousand feet, the height varying from 10 to 60 ft. and the width from 60 to 250 ft. In fact, on the core side, there is no definite end to the ore. The mineralization simply gets thinner and thinner, and the limit of working depends on the cost sheet and the profit from the recovery.

Jan 1, 1923

By W. F. Boericke

The character of the Wisconsin orebodies must be clearly understood to appreciate the difficulties encountered in sampling and estimating them. Unlike the western vein deposits, they do not lie between regular walls, but form large, often highly irregular bodies, on a single floor in the so-called Galena limestone. The bottom of the ore is nearly always on the clay bed (a flat generally well-defined clay seam a few inches thick) which marks the junction of the base of the Galena lime and the top of the next formation, the Trenton lime. Above the clay bed, the orebodies make the unique pitch and flat formation described by Chamberlin.' Theoretically, we should find two pitches, one on either side of the top crevice, diverging as they go down, with the final flats a considerable distance apart on the clay bed. The area between, known locally as core ground, should thus constitute a single defined orebody, with the richer portions near the pitches and the leaner portion in the center of the core. Practically, we find few examples of this perfect orebody. Almost invariably one pitch is better defined than the other, and often the opposite pitch is marked only by a faint line of fracture showing stronger mineralization than the wall rock, or it may be totally lacking. But with an orebody of any size or richness, at least one strong pitch usually tends to follow an east-west trend, or a quartering course. Late mining developments in the rich New Diggings field indicate that these pitches often assume a horseshoe or crescent shape, the richer ore being in the heart of the crescent and the pitches showing less mineralization as they extend outwards. In the northern end of the field, on the contrary, the pitches maintain generally a consistent direction, and have been mined for thousands of feet from the shaft. The length of the orebody may be several thousand feet, the height varying from 10 to 60 ft. and the width from 60 to 250 ft. In fact, on the core side, there is no definite end to the ore. The mineralization simply gets thinner and thinner, and the limit of working depends on the cost sheet and the profit from the recovery.

Jan 1, 1923

By Charles F. Brush

The compression of gases to a very high degree, for purposes of scientific research, has long presented serious difficulties to the physicist. Great advances have been made of late years in the construction of ordinary air or exhaust pumps, while very little has been done towards the improvement of compression pumps. The principal difficulties encountered in the construction of such apparatus are the existence of the so-called "dead space" in the pump barrels, leakage of the piston packings under high pressure, and the trouble arising from the unequal expansion of parts caused by the development of the latent heat of the gas during compression. Of these obstacles to success, the "dead space" is far the most serious, as it fixes a limit to the performance of the pump beyond which it is impossible to carry the compression. The writer having occasion, some time since, to make a series of investigations on gases very highly compressed, and finding no apparatus, or description of apparatus, adequate to produce the required

By C. H. Burgess

ON June 5, 1947, Secretary of State George C. Marshall in a speech at Harvard University outlined a plan for the economic recovery of Europe. The plan contemplated that the United States should provide assistance which would enable the European nations better to help themselves and to help each other to reconstitute from their war-torn lands conditions which would make possible decent standards of living. The Foreign Assistance Act of 1948 was passed in April of that year, and established the Eco-

Jan 10, 1950

By D. Harrington

WHEN the word gas is mentioned in connection with mining, almost invariably it is inferred that the explosive gas, methane, is in mind and that it must refer to coal mining. While it is true that methane occurs, or is likely to occur, in almost any or all coal mines, it is also a fact that the metal mines of the world have in them by far a greater variety of gases than have the coal mines. In many cases the gases in metal mines are as dangerous to individuals as the gases likely to be found in coal mines; in some instances the metal mine gases are even more deadly. The coal mine is more likely to have methane than the metal mine, in rare instances it may have high percentages of nitrogen or high carbon dioxide, or there may be a deficiency of oxygen where the air is confined in a blind end or in a sealed region; much more rarely there are found in coal mines in relatively small percentages, ethane, or other hydrocarbons with odor of ether, gasoline or kerosene, or there may be minute percentages of hydrogen sulfide. In time of coal mine fire or explosion, there is likely to be high carbon monoxide (4 per cent. or over in some cases) and if the coal contains much sulfur, there may be some sulfur dioxide in the fire fumes. In metal mines there are a number of cases of occurrence of methane and attendant explosions; some metal mines have appreciable percentages of the decidedly explosive hydrogen; in some metal-mining regions carbon dioxide flows into the mine, fills the workings and overflows just like water. In other regions, at many working faces there are high-temperature gases containing a mixture of gases of sulfur (sulfur dioxide, hydrogen sulfide and possibly SO3 in some cases) together with carbon dioxide and nitrogen, and the deadly hydrogen sulfide in lethal proportions is found in some high-sulfide metal mines at blasting time. Carbon monoxide constitutes a decidedly dangerous day by day hazard in connection with metal-mine blasting, because of the heavy charges of dynamite that are used and the use of fuse, which in burning gives off much carbon monoxide. The poisonous gas hazard is accentuated because of the relatively small openings where metal-mine blasting is done and to the inefficient ventilation of the usual metal mine.

Jan 1, 1930

By V. K. Zworykin

THROUGHOUT its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes; it. has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron. Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction -at the very best a tenth-of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. To overcome it, a different imaging medium must be employed. The existence of such a medium became evident when it was demonstrated' that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed, Furthermore, although a wave length may be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light: Actually, the electron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. THE ELECTRON MICROSCOPE Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the electrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

By A. P. Watt

Foreword...............................................................323 Location of District..................................................... 324 Geology and Mining..................................................... 325 Topography and Climate................................................. 325 Lcad Production of the District...........................................325 Operating Companies in Southeast Missouri................................ 327 History of the District................................................... 329 Present Method of Treating the Ore....................................... 335 Character of Ore Treated...........................................338 Chemical Analyses............................................. 339 Description of Polished Specimens.................................340 The Concentration Problem of the District............................. 341 Handpicking at Mine La Motte....................................... 343 Crushing............................................................344 Roll Practice in the District.......................................... 346 Screening Practice................................................... 347 Jigging the Ore..................................................... 347 Bull Jigging.................................................... 348 Hancock-jig Practice............................................ 348 Classification of the Ores.............................................. 350 Table Treatment....:............................................... 352 Regrinding of Middling.............................................. 354 Description of Marathon Mill..................................... 358 Results of Preliminary Tests.....................................359 Rod Wear in the Marathon Mill.................................. 367 Steel Consumption.............................................. 368 Design of Marathon Mills.............. :......................... 368 Treatment of Table Middling........................................ 368 Slime Concentration................................................. 370 Methods Used in the Past.......................................370 Present Methods of Treatment................................... 371 Flotation of Slime.......................;........................ 371

Jan 1, 1918