Search Documents

By William S. McAleer

Two major trends in the coal industry today focus attention on the need for heat-drying equipment of a simpler, more flexible and less expensive type than has been considered standard equipment for drying coal. These trends are: I. The tremendous growth in the use of mechanical equipment to load coal both in underground mining and strip mining, which necessitates efficient mechanical cleaning of the fine as well as the coarse coal and thus means a growing tonnage of washed fine coal? with its attendant moisture problems. 2. The growing consumer demand for the smaller sizes for use as domestic stoker coal, with increasingly rigid specifications covering size, ash, and moisture analyses. ACCEPTED PRACTICE In the past, when, for example, 4 in. too coal has been washed, there was little trouble in producing a washed product 4 to o with a satisfactory resultant moisture. The 4 to 3/8-in. could be taken from dewatering screens at a surface moisture ranging from 2.5 to 3.5 per cent, depending upon the size consist. The 3/8-in. to o coal was generally dewatered satisfactorily with centrifugal driers, to final surface moistures from 5.5 to 8 per cent, again depending upon size consist. The centrifugal type of drier has definitely proved itself to be the most economical type of machine to handle coal approximately 3/8 in. to o as recovered by dewatering screens or drainage elevators with 15 to 25 per cent surface moisture and turn out a product with moistures as stated above. Sometimes such moistures (5.5 to 8.0 per cent) in the product are satisfactory. If not, an ultimate moisture, lower than 3 per cent, is seldom required and the centrifugal drier removes 70 to 85 per cent of the total moisture to be removed. In certain districts there has been a growing tendency to circumvent the use of centrifugals or other types of driers, by dewatering over screens of the wedge wire type and wasting all the finer sizes. Sometimes all the minus 28-mesh has been wasted and often the size wasted has been as large as 1/8-in. By wasting these finer sizes, a lower moisture can be obtained in the finished product, but taking into account the cost of the tonnage so lost, plus the added cost of ultimately disposing of this wasted tonnage, often the cost will be greater than the cost of heat-drying in a modern plant, which makes possible the recovery of all the tonnage. Moreover, with the moisture standards for domestic stoker equipment even these wasteful approaches to its solution do not solve the problem and there remains only the alternative of heat-drying. HEAT-DRYING Until about four years ago, heat-drying of coal at the preparation plants was confined chiefly to drying the fine sizes (approximately 3/8 in. to 0). Occasional

Jan 1, 1941

By J. R. Finlay

Every business man who has reached the age of forty, or perhaps even thirty, must know from his own experience that there are occasional periods of "good times'' and others of "bad times "-booms and panics. Those who give to business some complexion of science have invented a semiscientific name for these alternations-the business cycle-indicating that it is a normal phenomenon which by its own nature repeats itself. The longer one lives and the more one enlarges his own experience by the study of history, the more of these cycles he knows and the more disposed he becomes to take their recurrence for granted. If these alternations can be put into the category of common- places, why not treat them as such? We are in a sharp depression right now, why worry about it? Is there not a certain average value for business that can be depended upon in spite of depressions? By way of rejoinder one might answer that war is the great commonplace of history, but when we get into one we generally find it worthy of attention. In the present case, many a man has lost two-thirds of his income, and he is extremely nervous about finding it again. The Southern Pacific Railroad earnings have dropped 75 per cent in the past year; Pennsylvania, 60 per cent; United States Steel Corp., about the same. The drop in current earnings is

Jan 1, 1932

Jan 1, 1924

By R. W. Harper, M. C. Fuerstenau, J. D. Miller

Data were obtained with hematite with octyl hydroxamate and oleate as collectors to determine the mechanism of collector adsorption and also to establish the roles that conditioning time and temperature assume in this system. The presence of hydroxy complexes of iron are apparently necessary for chemisorption of collector to occur, and it appears as if extended conditioning times and elevated temperature promote greater dissolution of the mineral and hence greater concentrations of hydroxy complexes. Data were also collected with two natural hematitic ores. With one ore that was ground to 70% - 15u, an addition of 0.4 lb per ton hydrox-amate resulted in a final concentrate recovery of 86% at a grade of 64% iron. Satisfactory concentrate grade could not be obtained with fatty acid under these conditions. The effect of conditioning time prior to the addition of collector was also examined with another ore. When the ore was conditioned for 3 min, 19% of the iron was recovered in the concentrate at a grade of 67% Fe. With a conditioning time of 7 min, 73% of the iron reported to the concentrate at a grade of 62% Fe. These products were obtained with an addition of 0.2 lb per ton hydroxamate. This ore also responded well to flotation with fatty acid. The use of potassium octyl hydroxamate as a collector for iron oxide has been the subject of an earlier study.1 From this initial study, it was suspected that hydrolysis of surface ferric iron was involved in collector adsorption. More recent work in other systems has shown that slight mineral dissolution, followed by hydrolysis of cations common to the mineral lattice, is apparently necessary, and that adsorption of these hydroxy com- plexes probably occurs prior to the adsorption of collector. In view of these facts, work has been continued on the hydroxamate-hematite and oleate-hematite systems to gain better insight into the mechanisms of collector adsorption on iron oxide. Microflotation experiments in conjunction with infrared analysis were used in this regard. In addition it was felt necessary to establish more clearly the responses that can be obtained from natural ores when hydroxamate is used as collector as compared to those obtained when fatty acid is used. Experimental Materials and Techniques Pure potassium oleate, potassium octyl hydroxamate, synthesized from hydroxylamine hydrochloride and methyl octanoate, and a distilled Tall Oil were employed as collectors. Conductivity water was used in the

Jan 1, 1971

By Gilbert H. Cady

HE application of geology to problems arising A in coal mining engineering and coal preparation has, in general, been somewhat remote, or the geological problems have involved such simple forms of geological knowledge that the attention of specialists in this field has not been commonly thought necessary. Furthermore, the geology of coal beds and coal mining has received but scant attention in our educational system, even in mining education; so that coal mining engineers have become somewhat conditioned against geological thinking. Geologists, on the other hand, have commonly failed to realize that there are geological aspects to coal mining and coal preparation problems. A further reason why geology receives so little consideration in coal mining undertakings in this country lies in the fact that our coal supplies are, or have been thought to be, almost unlimited, have been easily accessible, and very cheaply mined. Conditions have been changing within recent years. Failures can be less easily endured. Great inroads have been made on our bonanza deposits of easily mined coal and the increasing cost of coal and the increasing difficulty of finding it in easily accessible and large quantities places greater and greater importance on accurate information and good technique in exploration. It seems probable, therefore, that the opinions and aid of geologists will be more commonly sought than in the past in the exploration for coal and in the development and operation of coal mines, and analyses of mining conditions, preparation, and utilization.

Jan 1, 1951

By Gilbert H. Cady

HE application of geology to problems arising A in coal mining engineering and coal preparation has, in general, been somewhat remote, or the geological problems have involved such simple forms of geological knowledge that the attention of specialists in this field has not been commonly thought necessary. Furthermore, the geology of coal beds and coal mining has received but scant attention in our educational system, even in mining education; so that coal mining engineers have become somewhat conditioned against geological thinking. Geologists, on the other hand, have commonly failed to realize that there are geological aspects to coal mining and coal preparation problems. A further reason why geology receives so little consideration in coal mining undertakings in this country lies in the fact that our coal supplies are, or have been thought to be, almost unlimited, have been easily accessible, and very cheaply mined. Conditions have been changing within recent years. Failures can be less easily endured. Great inroads have been made on our bonanza deposits of easily mined coal and the increasing cost of coal and the increasing difficulty of finding it in easily accessible and large quantities places greater and greater importance on accurate information and good technique in exploration. It seems probable, therefore, that the opinions and aid of geologists will be more commonly sought than in the past in the exploration for coal and in the development and operation of coal mines, and analyses of mining conditions, preparation, and utilization.

Jan 1, 1951

By William Garrett

I have heard it said that the late Mr. Holley made use of this remark: " There is an inherent, cussedness about rolls which, so far, no man has been able to find out." I think this can be safely claimed in reference to steel, as there are certain peculiarities about it that are pretty hard to account for. Previous to the introduction of the Bessemer process there was, as it were, a great chasm between iron and crucible steel; and, outside of what futile attempts had been made in puddling steel, nothing had been done to fill this gap. The Bessemer steel struck a medium between the two, the softest of it not being able to take the place of good iron, while the hardest was not suitable to encroach very far upon the crucible-steel trade. The open-hearth process made quite an inroad into the latter, but only for the lower and cheaper grades; and, beyond a doubt, for the finest grades of tool-steel, the cruciblesteel business has a long life before it. On the other side of the line comes the " basic " process, which brings us a step nearer iron ; but to fill up the gap completely, comes the Clapp-Griffiths process, which makes a grade of material—call it what you will—that is as soft as iron, welds as readily, and is in a fair way to supersede iron altogether. For fifteen years, I was in the employment of the Cleveland

Jan 1, 1886

ARTHUR PHILLIPS, Chairman C. S. SMITH, Past-Chairman L. W. KEMPF. Vice-Chairman. E. E. SCHUMACHER, Vice-Chairman H. A. MALONEY, Treasurer FRANK T. SISCO, Secretary °9 West 39th Street, New York 1S, N. Y. Executive Committee 1945 1946 S. BARRETT H. L. BURGHOFF T. A. WRIGHT GERALD EDMUNDS L. L. W MAN A. A. SMITH, JR.

Jan 1, 1944

By L. Ibagos S., T. Balberyszski

The volumetric flow rate and the initial concentration of the copper sulfate solution influence the rate of reaction and, hence, the precipitation efficiency in a continuous launder cementation system. Using a model of such a system it was found that the precipitation efficiency is related to the two process parameters by the approximate expression [ log [1-n] = -[0.072 co 2.91 e – 0.511c o Q 1.15 ] N Q] where c is the initial concentration, Q, is the volumetric flow rate and N is the number of launders in the system. This expression agrees with an equation developed for the rate of the cementation process if it is assumed that the exponential factor represents the change in the surface area with concentration and the exponents 2.91-and 1.15 relate the hydrodynamic conditions and the surface concentration to co and Q. The experimental results are used to determine the values of a Precipitation Coefficient for any volumentric flow rate and initial concentration of solution. Knowing the Precipitation Coefficient, the total volume of launders that will result in a given precipitation efficiency can be calculated. It is established that maximum precipitation efficiencies are obtained for initial concentrations between 6.0 and 7.0 gpl and volumetric flow rates of approximately 350 m3 /hr Good agreement between calculated and actual launder volumes is obtained for a number of industrial operations for which a comparison is made.

Jan 1, 1973

By T. C. Clarke

The history of iron construction in this country well illustrates the three phases of thought described by Auguste Comte, the French philosopher. The first is the era of faith, when belief in the safety of structures rests on the authority of the designer. The second is the era of criticism, when plans of structures are analyzed with much mathematical skill, but the data upon which the chain of reasoning depends is assumed upon insufficient experiment. The third, upon which we are now entering, is a scientific era, which demands experimental proof. It also demands that this proof shall be derived from experiments made on full-sized specimens, such as are in actual use, and not upon toy models. Until the construction of the United States testing-machine, now at Watertown Arsenal, it was impossible to make such experiments with accuracy. We now have a machine in which we can test full-sized specimens of every part of a bridge or other structure that we want to use, and under the same conditions in which it is actually used. The next thing is to get money to make these experiments available. No private individuals can afford to do it, and even if they could, they might wish to keep the results to themselves. So that the next point is that we want money, and that, I believe, everybodly thinks we should ask Congress for. We want also, as has been said, some one who shall make a business of testing, and who has plenty of time. Persons who are employed in private business are too much in a hurry; they want to do a thing and get done with it, and then do something else; but government officers are entirely free from this feeling; time to them is of no account, and in experimenting that is the very element that is of value; it does not do to be hurried; the great thing is to get it right and to test your results, and go over it, again and again. And the experimenter who operates the machine must be some person educated up to the use of it. We then want a general advisory board who will indicate a plan of experiments, collect the results; and publish them. Some experiments were made the other day at the Watertown Arsenal upon full-sized

Jan 1, 1882

Geologist or Mining Engineer who has had sufficient experience to make examination of a large area and who can report upon economic value of any minerals found. Work will extend over a period of 2 or more years. Location, India. R-1660. Assistant Superintendent of malleable and gray iron foundry, young man. Must have thorough molding experience, especially on squeezers, knowledge of mixture control and operation of air furnaces, cupolas, and annealing ovens college graduate preferred. R-1727. Engineer thoroughly familiar with distilling, evaporating and drying machinery. Capable of taking charge of entire evaporator department, including engineering and selling. New Jersey. R-155C. Experimental Draftsman familiar with small automatic mechanisms, principally those produced in large quantities by punch-press methods, such as adding machines or typewriters. New York City. R-1566. Patent Draftsman.-At least 2 years' experience on perspective rend-ering of small automatic machinery. New York City. R-1570. Designer.-Familiar with hydraulic work and capable of going ahead with detail and design work without supervision. Pennsylvania. R-1575. Superintendent or Foreman. Knowledge of ceramics, clay products, electric porcelain, tile, factory materials, etc. New York State. Good salary to right man. R-1578. Designer. Experienced in designing mining machinery, including electric hoists. Canada (Quebec). R-1589. Construction and Operating Superintendent. Executive and thor-oughly experienced in the zinc melting industry. Will have charge of construction of plant and its operation. Salary $6000 to start; increase to $8000 later. India. R-1593.

Jan 11, 1919

By K. F. G. Hosking

I read Professor Gaudin's paper with great interest and pleasure because for some time I have held that the chemical aspect of comminution is a subject of considerable importance to the mineral dresser and deserves to be thoroughly investigated. It does seem appropriate, however, to emphasize the fact that "fresh" edges and corners produced by the grinding of solids display enhanced reactivity has been recognized and utilized in the development of certain mineral identification techniques. Some of these techniques are worth noting, not only because they might facilitate research in the aspect of mineral dressing under discussion, but also because they emphasize the fact that many mineral species commonly regarded as being very inert can display a surprising reactivity when in the freshly ground state. In 1951 Isakov published a number of tests for the components of certain mineral species which depend essentially on grinding in a mortar a mixture of the material under investigation with a solid reagent. Thus when stibnite, 4(Sb2S,), is ground with sodium or potassium hydroxide, the antimony is revealed by a momentary development of a yellow color which changes in air to orange-red. Other antimony minerals need a preliminary treatment before the test can be carried out. This consists of grinding with aluminium sulfate, ferric sulfate or potassium bisulfate, and breathing upon the resultant mixture.

Aug 1, 1956

By Charles E. Wait

HAVING had some experience in the use of gasoline-gas in a laboratory, I have been induced by frequent inquiry to present a few hints concerning it, which I hope may be of some value to those who are out of the reach of coal-gas, and who contemplate using this gas. While I will not delay to describe the method by which this gas is made, it may not be out of place to note that, unless frequent charges are put into the carburetter, the gas is variable in richness. This may be partially avoided, it is said, by repeatedly pumping from one cell in the carburetter to another. If a machine is in constant use for many months without re charging, the gas becomes rather poor for illuminating purposes ; but in this condition it may be burned in a Bunsen burner with advan tage. Could the gas be used always in this condition, no difficulty would be experienced, and it would be quite satisfactory for general laboratory purposes. Considerable annoyance, however, is experi enced whenever the machine is filled with gasoline. The Bunsen and other burners then produce a flame too smoky to be used with com fort, and, in fact, with most of them, a full supply of air; turned on at the base of the burner, will not suffice to completely burn off all the carbon. Finding it necessary to adopt some method by which I could get a flame free from unconsumed carbon, I adopted a plan which has in every way proved satisfactory. In addition to the pipe conveying the gas to the table, and ar ranged with a stopcock, there is brought to the table, within a fern inches of the gas-pipe, another pipe, conveying air direct from the pump. This pipe is also arranged with a stop-cock. The air- and gas-pipes are now connected with one pipe by a T joint; and to this last pipe is attached, by rubber tubing, the Bunsen or other burner. I have successfully used this simple system in connection with both small and large Bunsen burners, a burner with three tubes, arid a Fletcher burner; and recently I have added a new still to our equipment, and have been tising with it a Fletcher special high power burner No. 6, to which this system has been applied. With

Jan 1, 1886

By Kichizo Niwa, Toshio Yokokawa, Mitsuo Shimoji, Yoshihiko Watanabe, Satoshi Kado

A LTHOUGH a systematic research on diffusion in liquid metals has not been carried out, partial studies have been developed by various workers in several systems. A few recent papers among them have shown that this line of approach is quite useful for understanding the structure of the liquid state. Furthermore, it has been found in kinetic

Jan 1, 1958

[Appalachian Petroleum Section: James M. Kimbrough, chairman; John H. Adair, first vice-chairman; Walter L. Diddle, second vice-chairman; Byron M. Finch, secretary-treasurer. Balcones Section: Robert V. West, chairman; Frank W. Jessen, first vice-chairman; Zane V. Morgan, second vice-chairman; Brantley G. Myers, secretary-treasurer. Meets 4th Wed., Petroleum Club (San Antonio) or Terrace Dining Room (Austin) Billings Petroleum Section: Charles B. Evans, chairman; L. M. Lyon, first vice-chairman; Gordon E. Lansford, second vice-chairman; Fred. A. Haddenhorst, secretary-treasurer. Meets 3rd Tues., Billings Petroleum Club. California Coastal Section: Robert L. Richardson, chairman; David K. Hayward, first vice-chairman; W. Jackson Bransford, secretary; William N. Harwell, treasurer. Meets 3rd Thurs., Pierport Inn, Ventura. Caracas Petroleum Section: Edwin A. Moo re, chairman;. Jose Cirigliano, vice-chairman; Frank B. Davis, secretary; Robert N. Powers, treasurer. Meets 2nd Tues., Caracas Theater Club.]

Jan 1, 1961

Jan 1, 1904

By G. K. Manning, M. C. Udy, L. W. Eastwood

Those who have examined beryllium and beryllium-rich alloys under the microscope have noted the results of the difficulties encountered when preparing these materials for examination. Hard constituents are readily chipped and pulled out of the matrix, and the soft ones are easily gouged out or embedded with abrasive or other material. The matrix is easily deformed, which makes it very difficult to remove the effects of scratches. Furthermore, the matrix and some of the constituents are also readily pitted during etching, which makes the structure difficult to develop. The metallographic techniques designed to avoid these difficulties are neither radically new nor necessarily the best possible procedures. They were developed at Battelle to fill immediate requirements as part of a study of the preparation and pouring of beryllium melts as described in a separate paper. A part of the research program on the causes of gas unsoundness in beryllium castings entailed a study of the effects of such gases or gas formers as oxygen or oxides, nitrogen or nitrides, and carbon or carbides. These gases or gas formers, if dissolved in the melt, might be an important factor in the study of unsoundness caused by gas evolution in beryllium. Because it was necessary to be able to distinguish these gases or gas formers, if present as alloy constituents, from metallic phases also present as alloy constituents, a series of alloys was prepared with additions of the various possible metallic and non-metallic constituent formers. It should be emphasized that the constituents referred to as gases or gas formers are important in the study of gases in beryllium only if they form a part of the alloy, that is, if they dissolve in the liquid or solid metal. During the first part of the development of metallographic techniques, the Massachusetts Institute of Technology, unpublished report (TC 3315, Nov., 1945) by Paul Gordon, describing various microconstituents in beryllium, was quite useful. Of particular interest in this report is the confirmation of one of the conclusions drawn from the present investigation, that is, that a distinct oxide phase apparently does not occur in beryllium. The Preparation of Metallographic Specimens GRINDING PROCEDURE The original specimen is either sawed or cut on an abrasive wheel to a convenient size. For best results, the surface to be polished should not be more than about 1/4 in. square, and it is convenient to mount the specimens in bakelite to facilitate handling. Two alternative grinding procedures have been developed. As one alternative, specimens are ground successively on 120-, 240-, and 400-grit, wet-or-dry metallographic discs. The abrasive discs are revolved at 1750 rpm on a conventional pedestal grinder. The coarsest disc (120 grit) is used either wet or dry, and in most instances, it can be eliminated from the procedure. Grinding on the two finer discs (240 and 400 grit) is accompanied by the application of kerosene. The technique consists of holding an oil can, containing kerosene, in one hand and the mounted specimen in the other hand. While the grinding is being done, several drops of kerosene are applied every few seconds close to the center of the disc. Carbon tetrachloride serves at least as well as kerosene as a lubricant; perhaps it is slightly better, but it volatilizes so readily that an additional health hazard is involved. Light oils and water are not satisfactory for the finer grinding operations. The second procedure is perhaps slightly slower than the first and requires a more careful technique, but it eliminates the use of kerosene. The specimen is first ground wet on a 240-grit disc, followed by dry grinding on a 400-grit disc. Finer grinding does not appear to be necessary with either of the two alternative procedures. The pressures used throughout either grinding operation must be extremely light, that is, barely sufficient to hold the specimen in contact with the disc; otherwise, flow and chipping are almost certain to occur. In both procedures, it is essential that the discs be sharp and that they be discarded as they show evidence of becoming dull or loaded. In general, not more than four or five specimens can be ground on a disc before the disc becomes dull enough to warrant discarding it.

Jan 1, 1950

By E. T. Dumble

Discussion of the paper of E. T. DUMBLE, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. .1623 to 1638. E. L. DEGOLYER, Norman, Okla. (communIcatIon to the Secretary*).-Referring to Mr. Dumble's description of the stratigraphy of eastern Mexico, I should like to question the classification of the ?Papagallos? or ?Mendez? shales as being of Cretaceous age and the so-called overlapping of the Papagallos or Mendez shales by the Alazan shales; the classification of the San Felipe series as Cretaceous, and the correlation of the San Felipe series with the San Juan limestones. Mr. Durable apparently recognizes the continuity of the great shale formation by his use of the terms "Papagallos" and "Mendez," as equivalent and interchangeable, since the Papagallos Hills in the State of Nuevo Leon and Mendez Station in Northern Vera Cruz, localities at which the shale formation outcrops, and from which the formation names are taken, are approximately 250 miles apart and on opposite sides of the Tamaulipas barrier. The Papagallos shales (evidently referring here to the northern extension only) are said to be non-fossiliferous and no reason for .their Cretaceous classification is given, though in a previous article' they are classified as Cretaceous because at their northernmost outcrop they "have the same relation toward the overlying Tertiary that the Escondido (Cretaceous) has through its whole extent." The Alazan fossil locality was found by me and the first collections from it were sent to Dr. Dall; about 17 species of marine invertebrates were recognized by him, the fauna noted as having a distinct Pacific tincture, and the age of the formation from which they cause pronounced lower Eocene. The outcrop of the shale formation has been traced continuously from this point by me and my assistants into the Panuco River region, where Eocene fossils are reported at a depth of 1,810 ft. in a well at Topila.2 From Topila the formation has been traced continuously north to the Padilla-Jiminez region in Central Tamaulipas. Lithologically, the formation is fairly constant and though I am only generally acquainted with it north of the Padilla-Jiminez region, until definite evidence of the Cretaceous age of the Papagallos shale in its type localities, or of an overlap, is available, it seems to me more logical to consider the shale formation a single stratigraphic unit of Eocene age.

Jan 12, 1915

By Arthur A. Brant

Let us start back as far as possible, to the beginnings of this universe, some 5 billion or more years ago. This is a time interval that can be crudely underestimated by the moon-earth tidal friction effects that have increased the length of the day by about 1/1000 second per century-from a 5 to 7 hour day to its present 24-and have moved the moon away at 5 inches per year to its present 240,000 miles. The oldest stony meteorites from interplanetary space give an age dating of some 4.6 billion years, approximating the time of formation of our earth. Further, certain stars pulsate, the period of pulsation being related to their absolute brightness. Measuring apparent brightness and comparing, gives the distance away. Thus Hubble and Shapley of Harvard, from 1925 on, were able to show that the universe reached as far as our telescopes could scan. The Doppler shift of the hydrogen red lines could only mean that the nebulae, or galaxies, were moving away at velocities increasing with their distances, by 180 km/ sec velocity increase for every million light year's distance. In short, the universe is expanding like an exploded bomb.

Jan 4, 1964

26. G. H. S. Price, S. V. Williams, and G. J.O. Garrard: Heavy alloy, its production. properties and uses. Metal Industry (1941) 599 354s 372. 394. 27. R. Kieffer and W. Hotop: p. 320 of ref 12. 28. F. R. Hensel. E. I. Larsen, and E. F. Swazy: Physical properties of metal compositions with a refractory metal base. Chap. 42, 483, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 29. R. Kieffer and W. Hotop: p. 290 of ref. 12. 30. H. Freundlich: Kapillarchemie. 211 (1923) Leipzig. 31. W. Ostwald: Zisch. f. Phys. Chemie. (1900) 34, 503. 32. G. A. Hulett: Zisch. f. Phys. Chemie. (1901) 37. 385; and (1904) 47, 357. 33. J C. Chaston: Discussion to Price, Smithells and Williams, p. 257 of ref. 4. 34. W. Dawihl: Untersuchungen ueber die Vorgaenge bei der Abnuetzung von Hartmetallwerkzeugen. Ztsch. f. techn. Phys. (1940) 21 336. 35. W. Dawihl and J. Hinnueber: Ueber den Aufbau der Hartmetallegierungen. Kol-loidzlsch. (1943) 104, 233. 36. F. Skaupy: Dispersoidchemische und verwandte Gesichtspunkte bei Sinter-hartmetallen. Kolloidzlsch. (1942) 98, 92; and (1943) 102, 269. 37. F. C. Kellcy: Cemented tantalum car- bide tools. Trans. ASST (1932) 19, 233. 38. E. W. Engle: Cemented carbides. Chap. 39, 436, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 39. W. Dawihl: Zlsch. f. Melallkunde. (1940) 32, 320. 40. P. M. McKenna: Tool Materials (Ce- mented Carbides). Chap. 40. 454. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 41. G. A. Meerson. G. L. Sverev, B. Y. Osinovskaja: Zhurnal Prikladnoi Khimii. (1930) 139 66. 42. A. G. Metcalfe: The mutual solid solubility of Tunesten Carbide and Titanium carbide- Metal Trealmenl (1946) 13, 127. 43. P. Schwarzkopf: Powder Metallurgy. 196-201 and 354-356 (1947) New York. 44. H. Burden: The manipulation and sintering of hard-metals. Special Rep. No. 38, p. 78. Iron and Steel Inst.. 1947. London. 45. W. D. Jones: Principles of powder metal- lurgy. 150. (1937) London. 46. J. E. Drapeau: Sintering of powdered copper-tin mixtures. Chap. 32. 332, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 47. H. E. Hall: Sintering of copper and tin powder. Metals and Alloys (1939) 10, 297. 48. F. Sauerwald: Present status of powder metallurgy. -.Melallwirlschafl. (1941) 20, 649. 671. 49. H. L. Wain: Powder metallurgy; influence of some processing variables on the properties of sintered bronze. Report ACA-25. Australian Council for Aeronautics (1946) Melbourne. 50. S. L. Hoyt: Constitution of copper-tin alloys. Metals Handhook, 1364. (1939) Cleveland. 51. T. Ishikawa: Studies on the interdiffusion of copper, tin and graphite powders. Nippon Kinzoku Gakkai-Si (1937) I, 226. 52. A. Carter and A. G. Metcalfe. The struc- ture of porous bronze bearings. Special Rep. No. 38, p. 99. Iron and Stecl Inst. (1947) London. 53. R. P. Koehring: Sintering atmospheres for production purposes. Chap. 25, 278. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 54. C. G. Goetzel: Some properties of sintcred and hotpressed copper tin compacts. Trans. AIME (1945) 161, 569. 55. J. W. Lennox: The production of some non ferrous engineering components by powder metallurgy. Special Rep. No. 38. p. 174. Iron and Steel Inst., 1947, London. . P. Duwez and H. E. Martens: The power metallurgy of porous metals and alloys having a controlled porosity. TP 2343, Metals Tech. April 1948. This volume. p. 848. 57. E. A. Owen and L. Pickup: X-ray study of the interdiffusion of copper and zinc. Proc. Royal Soc., London, Series A. (1935) 149, 283. 58. C. G. Goetzel: Sintered and hotpressed compacts of copper-zinc powder. Chap. 34. 352, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 98, R. Chadwick. E. R. Broadfield, and S. F. Pugh: Observations on the pressing. sintering, and properties of iron-copper powder mixtures. Special Rep. No. 38, p. 151, Iron and Steel Inst. (1947) London. 60. A. Squire: The properties of iron-copper compacts. Watertown Arsenal Lab. Rep. WAL No. 67101. 61. F. C. Kelley: Properties of sintered iron- comer uowder. Iron Age (Aug. 15. 193) 158 57. 62. G. H. Howe: Sinterinn of Alnico. Iron Age (Jan. 11. 1940) 14.5, 27. 63. R. Kieffer and W. Hotop: p. 359 of ref. 12. 64. W. Hotop: Permanent magnets from sintered iron-nickel-aluminum. Stahl und Eisen (1941) 61, 1105. 65. P. R. Kalischer: Some experiments in the production of aluminum-nickel-iron alloys by powder metallurgy. Trans. AIME (1941) 145, 369. 66. S. J. Garvin: Production of sintered per- manent magnets. Special Rep. NO. 38. p. 67. Iron and Steel Inst. 1947, London. 67. F. C. Kelley: Discussion to P. R. Kalischer. p. 375 of ref. 65. 68. R. Kieffer and W. Hotop: p. 357 of ret, 12. 69. C. H. Howe: Sintered alnico. Chapter 48, 530, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. Powder Metallurgy Seminar (C. G. Goetzel presiding) C. G. Goetzel—The seminar has been opened by a man who has been active in the field for over fourteen years and has made, since then, some major contributions to the advancement of the art. After having been associated with the Moraine Products Division of General Motors Corporation for over ten

Jan 1, 1949