Search Documents

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution. ALTHOUGH cyanide solvents are used very ex-x*. tensively for the recovery of gold from ores and concentrates, the normal rate of solution of the precious metal as determined by Barsky, Swainson, and Hedley,1 and others2 is less than about 3 mg per sq cm of exposed gold surface per hour, corresponding to a corrosion depth of approximately 1.5 microns (0.00006 in.) per hr. Although the slow rate may be increased to some extent in certain cases, as, for example, when the the gold is partially imbedded in iron pyrites,3 the leaching operation is generally the most time-consuming step of the cyanide process. Frequently it is necessary for the leaching solvents to remain in contact with the ores for 50 to 200 hr in order to dissolve all of the gold particles.' Not only does the slow solution rate cause some increase in the capital costs, but the cyanide consumption also may be increased because of vaporization of hydrocyanic acid and secondary reactions with minerals such as malachite (CuCO3 • Cu(OH)2), and pyrrhotite, which often are associated with gold. It is not surprising that numerous attempts have been made to accelerate the dissolution of gold in cyanide solutions. Experimental Gold Leaf Test: The gold leaf test was apparently originated by M. Faraday, who, by means of it, discovered that dilute cyanide solutions would dissolve gold readily in the presence of oxygen. The usefulness and reliability of the test have been discussed elsewhere.5,6 Essentially, the method consists of determining the time required for 5-ml portions of cyanide solvents to dissolve squares of 23 carat gold leaf, 0.5 cm on edge, when shaken in 10-ml test tubes with the solvents. The weight of gold leaf per test was 0.051 mg as determined by the direct weighing of a leaf 8.6x8.6 cm (weight = 15 mg) and measuring the area of the test sample (0.25 sq cm). Gold leaf is of remarkably uniform thickness.6 Since gold leaf, like native gold, contains small amounts of copper and silver, the results are comparable with those one might expect in cyaniding gold ores. As six or more tests can be made simul- taneously, the relative efficiencies of the solvents can be evaluated readily. All dilute solutions of lead, bismuth, thallium and mercury salts were prepared by the ordinary dilution method used by chemists. Our C.P. sodium cyanide and buffering reagents had no detectable amounts of either sulphide ion or heavy metals. Soluble Sulphides in the Cyanide Process: The action of soluble sulphides is of interest in the study of the dissolution of gold in cyanide solutions. That gold ores which contain compounds of arsenic and antimony often are not amenable to direct cyanide treatment is well known, and it said that arsenic and antimony are "cyanicides."7 It is commonly believed that part of the sulphur content of such ores is soluble in alkaline solutions to give sulphide ion, which reacts with the free cyanide content of the leaching solutions to form inert thio-cyanates or reacts with the dissolved oxygen to form sulphites or sulphates.8 A purpose of this paper is to demonstrate that sulphide ion may behave in a manner that cannot be explained by either the oxygen-depletion or thiocyanate formation theories and to prove directly that concentrations of sulphide ion which cannot be detected even by colorimetric methods may retard the dissolution of gold.

Jan 1, 1951

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution. ALTHOUGH cyanide solvents are used very ex-x*. tensively for the recovery of gold from ores and concentrates, the normal rate of solution of the precious metal as determined by Barsky, Swainson, and Hedley,1 and others2 is less than about 3 mg per sq cm of exposed gold surface per hour, corresponding to a corrosion depth of approximately 1.5 microns (0.00006 in.) per hr. Although the slow rate may be increased to some extent in certain cases, as, for example, when the the gold is partially imbedded in iron pyrites,3 the leaching operation is generally the most time-consuming step of the cyanide process. Frequently it is necessary for the leaching solvents to remain in contact with the ores for 50 to 200 hr in order to dissolve all of the gold particles.' Not only does the slow solution rate cause some increase in the capital costs, but the cyanide consumption also may be increased because of vaporization of hydrocyanic acid and secondary reactions with minerals such as malachite (CuCO3 • Cu(OH)2), and pyrrhotite, which often are associated with gold. It is not surprising that numerous attempts have been made to accelerate the dissolution of gold in cyanide solutions. Experimental Gold Leaf Test: The gold leaf test was apparently originated by M. Faraday, who, by means of it, discovered that dilute cyanide solutions would dissolve gold readily in the presence of oxygen. The usefulness and reliability of the test have been discussed elsewhere.5,6 Essentially, the method consists of determining the time required for 5-ml portions of cyanide solvents to dissolve squares of 23 carat gold leaf, 0.5 cm on edge, when shaken in 10-ml test tubes with the solvents. The weight of gold leaf per test was 0.051 mg as determined by the direct weighing of a leaf 8.6x8.6 cm (weight = 15 mg) and measuring the area of the test sample (0.25 sq cm). Gold leaf is of remarkably uniform thickness.6 Since gold leaf, like native gold, contains small amounts of copper and silver, the results are comparable with those one might expect in cyaniding gold ores. As six or more tests can be made simul- taneously, the relative efficiencies of the solvents can be evaluated readily. All dilute solutions of lead, bismuth, thallium and mercury salts were prepared by the ordinary dilution method used by chemists. Our C.P. sodium cyanide and buffering reagents had no detectable amounts of either sulphide ion or heavy metals. Soluble Sulphides in the Cyanide Process: The action of soluble sulphides is of interest in the study of the dissolution of gold in cyanide solutions. That gold ores which contain compounds of arsenic and antimony often are not amenable to direct cyanide treatment is well known, and it said that arsenic and antimony are "cyanicides."7 It is commonly believed that part of the sulphur content of such ores is soluble in alkaline solutions to give sulphide ion, which reacts with the free cyanide content of the leaching solutions to form inert thio-cyanates or reacts with the dissolved oxygen to form sulphites or sulphates.8 A purpose of this paper is to demonstrate that sulphide ion may behave in a manner that cannot be explained by either the oxygen-depletion or thiocyanate formation theories and to prove directly that concentrations of sulphide ion which cannot be detected even by colorimetric methods may retard the dissolution of gold.

Jan 1, 1951

By Dennis K. Mortensen

The Role of the Operator The ultimate objective of any installation is to be able to accomplish the useful work that it was originally designed for. The operator needs a tool that he can both operate effectively and maintain efficiently. The overall design and subsequent installation of a comminution circuit should be a marriage of good engineering practice and practicality. Since the operator must operate and maintain his equipment, his input into the design and installation is vital to its ultimate success. The design of a crushing or grinding circuit is dependent upon many factors including flowsheet design, equipment selection, physical layout, space restrictions, climatic restrictions and considerations for future expansion. The operator must live on a day-to-day basis with the results of the final design and installation. The most satisfactory operation will result when the operator has a major input into each of the criteria that are used to define the final design and installation. The operator referred to is not only the mining company or organization that is having the installation built for its specific use but, more specifically, the person or persons that will actually be responsible for its daily operation and maintenance. Future references to the "operator" will include those individuals with that daily reponsibility. The operator's input into the installation of the circuit is of equal importance to his input into the design. The engineering organization which puts together all of the various design drawings for circuit installation is generally restricted to trying to get all of the details onto a multitude of 24" x 36" two dimensional drawings with a few isometric drawings thrown in. It's almost impossible to get all of the details of a final installation onto all of the drawings, and field modifications are necessary to make everything fit properly. In a multilevel installation, such as a grinding or crushing circuit, it is difficult to envision space requirements to adequately operate and maintain the various pieces of equipment simply by looking at a set o£ drawings. For some designs it is helpful to build a scale model so that a more realistic view of what the installation will look like can be seen. The scale model allows the operator to make whatever changes in design are needed to operate and maintain his equipment most effi-

Jan 1, 1982

By W. M. Lehrer

RECENT development of high-temperature brazing alloys has required information regarding the eutec-tic temperature and composition of the Pd-rich section of the Pd-B system.. Literature on this subject was found to be scanty with no complete system yet determined. Buddery and welch1 report an inter-metallic compound occurring in the Pd-B system at 6.33 wt pct B (PdsBz). Another source, Sieverts and Bruning,2 indicates that after annealing at 700°C, a 1.6 and a 2.0 wt pct B alloy were two phase whereas a 0.75 pct B alloy was single phase. Recent work3 using a hot-stage microscope has proposed a eutectic temperature of 743OC. This method utilized the observation of the onset of incipient melting at grain boundaries. The eutectic composition, however, was not determined. METHODS AND PR0CEDURES Five alloys were prepared by triple inert arc-melting high-purity palladium (95.98 pct) with additions of 2 to 6 pct purified amorphous boron. The alloys were crushed within a hardened steel mortar with a steel pestle. The 2 pct alloy, however, was too tough to be crushed in the above manner so was crushed by successive reductions through a rolling mill. Approximately 17 to 18 g of the crushed alloy was used in the thermal analysis. The alloys were melted in pure quartz crucibles. The thermocouple protection tubes were also of quartz and fused along the inside wall of crucibles to prevent floating of the thermocouple. This was an expediency as centering of the thermocouple in the melt would have been preferable. Melting was done in a tube furnace with a slow flow of tank helium maintained as a protective atmosphere. Heating and cooling rates were maintained at 3.5OC per min through the critical temperature ranges by means of a synchronous motor hook-up to a furnace controller. All specimens were heated to 100°C over the indicated liquidus on heating prior to reversing to the cooling cycle. Specimens emerged from the furnace with mirrorlike brightness attesting to the protective quality of the helium atmosphere. Thermal arrests were detected by the differential thermocouple technique using chrome l-alumel couples and nickel as the reference specimen. Arrests were recorded on a Leeds-Northrup automatic X-Y recorder. The specimen temperature and temperature difference were read to + 7.5OC and ± 1.5OC, respectively. These readings were well within the sensitivity of the instrument amplifier. Chromel-alumel couples were used in lieu of Pt-Rh as very few arrests were contemplated in excess of 1200" to 1300°C, the approach of instability. No standardization was performed on these thermocouples subsequent to their use. RESULTS The thermal arrest temperatures obtained are plotted in Fig. 1 as a function of wt pct B. The composition function was obtained by chemical analysis of portions of the specimens after the thermal analysis was completed. The 2 to 6 pct nominal alloys were found to have 1.80, 2.35, 3.65, 4.18 and 5.90

Jan 1, 1960

By E. Gaujot

IN connection with the question of coal waste and economy in mining, we would call the attention of those interested to an apparatus invented by M. Dernencourt, Superintendent of the Anzin Division of the Anzin Coal Company, North of France. This apparatus is known in France and Belgium under the name of prop screw-jack (vis botte), and has been used with good results in the above-named countries for some years past. M. Ponson gives, in his " Trait6 de I'exploitation des Mines," a description of it (page 533), but as the description given is old, the work not widely known in this country, and as some valuable improvements have been made since, I thought it might be useful to give a description of it, having seen it in 'operation in 1867, while in Europe to attend the great Exposition, and on a scientific tour to the mining districts of France, Germany, Belgium, and Italy. The prop screw-jack is composed of the following pieces : I. The body or column B, Fig. 4 [Plate (I)], of oak or yellow pine, sawed square, the bark taken off, and any length, proportionate to the vein. The smallest are 10 inches diameter at the base, and 9 inches at the top, the height being from 12 to 15 inches less than the size of the vein. In the axis of this column, and at the top end, is a cylindrical opening or hole, C, 22 inches diameter, 10 inches deep, for the screw, S. II. Two wrought-iron rings, R R, to strengthen the two extremities of the column ; the rings must be put on hot. III. A cast,-iron washer, E, with hole in centre a little larger than the screw, to be put on the top of the column, and on which the nut is to rest; the top side of this washer must be faced on the lathe, also the bottom of the nut, to prevent friction. IV. The screw, S, having a total length of 12 inches and a diameter of 24 inches (for very high veins this diameter may be increased to 3 inches), and has on its top a wrought-iron plate, T,

By Albert W. Giles

The splitting of the coal by partings is a familiar feature of many coal beds. The partings are normally argillaceous, more rarely sandy or calcareous. The material is usually fine-grained, less frequently coarse-grained to conglomeratic. Many partings are wedge-shaped, others are lenticular, and in some coal beds thin partings but one or two inches thick persist as thin sheets throughout areas of regional extent. The origin of the partings differs, and in some cases is obscure and uncertain. Origin of Thick Partings Wedge-shaped Partings Wedge-shaped partings are normally of indefinite linear extent but of short transverse section. They are developed adjacent to the borders of the original peat-forming swamp or around islands formed within the swamp, hence their presence is indicative of the approximate limit of the coal bed or of an interruption in the continuity of the coal bed. Following deposition of the parting gradual reestablishment of swamp conditions is followed by burial of the parting with accumulating peat. Partings developed adjacent to the borders of swamps normally thicken toward the periphery of the swamp and represent either detrital materials carried in from adjacent land areas during floods or materials carried in by advancing waves and currents after a barrier confining the swamp had been breached by the waves. Partings formed in the manner first mentioned should become coarser and more arenaceous toward the source of supply of the detrital materials, and the overlying and underlying coal should gradually grade into carbonaceous shale as the margin of the original swamp is approached. Partings formed by advance of waves across a barrier should be largely or entirely arenaceous, thin wedges of short longitudinal section, possibly with fossils of marine or brackish affinity. The subjacent coal normally should "pinch out" against the barrier, and the overlying coal continue to the barrier, or even extend across it, depending on the geographic conditions established following the breaching of the original barrier. Islands may be formed in swamps in a number of ways. They may represent local uplift of the swamp floor during earthquakes, or

Jan 1, 1934

By C. S. Sivil

To modern civilization the platinum metals are of inestimable value. Their distinctive properties, both physical and chemical, render them indispensable in an age in which the processes of the laboratory are becoming an essential part of the daily life of the world. Generally, their function, though vital to particular processes, is not spectacular, and so remains unknown to all except the operators. Early Methods of Manufacture The properties of platinum were recognized as of prime importance for scientific work at a very early date, probably between 1750 and 1760. The difficulty of making articles from it seemed almost insurmountable, because no means of attaining the temperature necessary to melt it were known at that time. It is true that solid platinum could be obtained by fusing the metal with a more volatile metal such as arsenic, which was subsequently driven off by baking, but such a method, at its best, would give only a very brittle product, which was totally unsuitable for the purposes for which it was intended. Little, if any, progress could be made until it was discovered that platinum sponge, heated to white heat and hammered in an iron or clay mold, would metallize and retain the shape of the mold. This was a process that could not be wholly satisfactory but from it developed the method of pressing the sponge in a mold and forging it at white heat into wire or sheet. At present a somewhat similar process must be used for fabricating articles of tungsten, molybdenum and other metals of high fusing point, as with these metals we face today the same problems that the scientists of the eighteenth century encountered with platinum, but possibly the next significant advance in the metallurgy of these metals will be the devising of means to melt and cast them. TO some extent this method of preparing platinum has survived, particularly in Europe. There are one or two objections to it, but they are not serious, as they can be surmounted with proper precautions. In the first place, the material is spongy and its millions of cavities contain entrapped air. Unless this is removed by thorough forging above 1000" C. the resultant sheet shows blisters. To give such a thorough forging,

Jan 1, 1931

By H. Ries

In the marketing of mineral products, it is always highly desirable for both the producer and the consumer to be able to discuss things in a common language, and this can only be done if there are standard methods for expressing the properties of the raw materials. Having developed such a form of expression, the next step would be the making of specifications, which may serve as a basis for selecting raw materials. Considering the large number of non-metallic minerals that are used, there are not a few for which there are no standard laboratory tests to be used in determining their properties, or even standard specifications on which grades or market price may be based. Indeed in many cases the consumer simply requests the producer to submit samples, and rejects or accepts them without any explanation. Could the producer know in advance just what the consumer needed, time and money might often be saved. It appears to the writer that it is of the highest importance to devise standard laboratory tests wherever possible, as this enables the consumer to state definitely what he needs, and is of great assistance to the producer. It should also work to reduce misunderstandings and disputes. In the case of sands, we find that they show a wide variation in their character, ranging from those that are so coarse as to be of gravelly nature to those that are so fine that they might be classed as silt; and from very clayey ones to those that are practically free from clay. For this wide range of sands, we have a corresponding variety of uses, which are based mainly on the physical properties of the sand, although these are not always very definitely stated. The chemical composition need rarely be considered, if the sand is of siliceous nature. To determine and express these properties there should be standard tests, which are to be followed in all cases where the material is tested in the laboratory. The use of sands for foundry work (making molds or cores) is old, and it has been recognized for some time that the important properties to be

Jan 1, 1926

Discussion of the paper of Ernest Stütz, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1257 to 1265. H. 0. HOFMAN, Boston, Mass.:-I have hunted in vain for a figure which gives a dehydration temperature of cement. I was wondering if Mr. Stütz had a figure of that kind. E. STÜTZ :-No, I am afraid I have not. H. 0. HOFMAN :-I believe some figures have been published that cement disintegrates at 400° or 500° C. It seems tome a very low temperature. Mr. Stütz just made the statement that the disintegration of this briquette begins at the temperature at which the briquette begins to sinter. E. STÜTZ :-Above the sintering point. H. 0. HOFMAN :-The sintering point would be about 1,200° C. E. STÜTZ :-Yes, roughly speaking. I am afraid I have no information about the exact degree of dehydration. H. O. HOFMAN :-I have looked a great deal for such a figure and I have not been able to obtain it. Professor Howe says I might have tried myself. But my interests were directed in another line; although-that is, perhaps, a good suggestion. CHAIRMAN RICHARDS:-Is not Portland cement sometimes used for the test in a cupellation furnace and a drying-out furnace ? H. O. HOFMAN :-Yes, it is used, but that is a higher temperature, of course. But I have been trying to get a figure as to where it loses all its water. I understand it begins to lose water at 500° C. But there are different silicates or hydrosilicates in the cement, so that one would have four or five or sit figures to show the different stages at which the cement loses its water. CHAIRMAN RICHARDS :-I would ask whether the use of this material in blast furnaces has shown increased capacity of furnace or decreased consumption of fuel.

Jan 12, 1913

LINN BRADLEY, H.' D. EGBERT and W. W. STRONG (communication to the Secretary*).--In the discussion of the paper, a request was made for a further explanation of the curves given on Chart I. In preparing the curves given on this chart, a typical blast-furnace top gas having the following composition by weight was assumed: Per Cent. C02 21.00 CO 24.00 Hz 0.25 CH4 0:25 N2 54.50 For any given top-gas temperature, Curves A, B, C, D, and E indicate in British thermal units the sensible heat lost in cooling the top gas to 60° F. by wet-cleaning methods. Top-gas temperatures are plotted as abscissae, sensible heats above 60° F. in British thermal units are plotted as ordinates, and separate curves are drawn for top gases carrying various amounts of moisture. For any given stove exit-gas temperature, curves A1,-B1, C1, D1, and E1, indicate in British thermal units the sensible heat carried out of the stoves by the moisture which is left in the top gas when it is dry-cleaned and enters the stoves hot. This moisture is removed when the gases are wet-cleaned and the sensible heat which it carries out of the stoves is therefore saved. As before, separate curves are drawn for top gases carrying various amounts of moisture. The curves in Fig. 1, therefore, indicate graphically how much more sensible heat is conserved by cleaning the top gases by the dry-hot method than is conserved by cleaning the top. gases by a cold-wet method and thus removing the greater part of the moisture carried by them. They also show of how little moment it is from a heat conservation standpoint whether or not the moisture carried by the top gases is removed before they enter the stoves. That wet cleaning secures the removal of this moisture and is thus to be recommended from a heat conservation standpoint is an argument often advanced by advocates of wet cleaning. The curves of Fig. 1 show how fallacious such an argument is.

Jan 6, 1917

By W. J. Parton

D. R. MITCHELL*—The Chairman mentioned that we have had many papers on cleaning of fine coal and treatment of wash water solids. There are, of course, two reasons for that. One is that we have legislation, particularly in the east. that is making us go into these things whether we want to or not. It just so happens at the present time that I have four plants that are going up under my general direction, three new and one rehabilitation job, and in all of them, we have these problems. Therefore, I was very happy to be able to listen to these papers, because some of the things that are in them are going to help me solve some of the problems that I am facing. Of course, the second reason why we are concerned about fine coal recovery is the fact that coal has become a luxury item in a good many places, particularly in the anthracite region, so that we cannot afford to have it go to waste like we did in former years. There is a third minor reason, and that is that we are finding how to handle and use the extremely fine sizes that we did not know how to use in former years. Now, I have a couple of questions that I would like to ask. First, what are the maximum solids that you could have in a pulp going to one of these launder screens? I realize that it would be for anthracite. Second, of course the life of these screen surfaces is not very long— with brass or bronze, I believe it is a week, and with stainless steel, a month. Would it be possible to use screen surfaces like the Bixby-Zimmer round rod for the small sizes and possibly increase the life? Have you experimented with that? Another point that I would like to bring out, both in Mr. Parton's paper and in some of the others, in studying cyclones and any settling apparatus where we use orifices, the life of the orifices is very short, and that is a problem that still has to be solved. The capacity of the cyclone seems to be small, and if you have a bat-

Jan 1, 1950

By R. A. Liddle

Intermitt'en'I'ly during the past 10 years showings of oil and gas in tests drilled in the eastern part of Texas have stimulated the search for production. Tests on the flanks of the long-known salt domes, principally Keechi and Butler, have found oil in small quantity in the Woodbine formation of the basal part of the Upper Cretacrous. In the central part of Cherokee County, Colliton et all in 1926, in their Clapp No. 2 found a good showing of 37" B6. oil at about 3500 ft. Several wells were drilled in 1926 and 1927 as a result of this showing. On Jan. 22, 1927, Humble Oil & Refining Co. wildcatting on Carey Lake salt dome, obtained commercial production in its Clark No. 1. This inaugurated intensive exploration both for salt domes and for other types of structure. As a result several new domes and a few promising structures of other types have been discovered. Development in East Texas durinG 1927 Carey Lake Dome Location.—On the Neches River in Anderson and Cherokree counties, 10 miles west of Jacksonville, Cherokec (lounty. (Fig. 1.) date of Discovery.—During 1925 geologisls of the Humble Oil & Refining Co. working in the Neches River valley discovered slight surface fracturexs, cratic dips, and slickensided clays and sands in green-sands of the Mount Selman formation north of Carey Lake. A number of core tests were drilled by the Humble Oil & Refining C'o. during 1925 and 1926, some more than 1500 ft. deep, to check their surface obsuvations of faulting, and the possibilities of a salt dome. On May 16, 1927, solid rock salt was reached at 2142ft. in the first deep test on the prospect. Surfacc Indications.—Surface indications of the Carey Lake dome, though not as evident as manifestations at the previously known domes of Palestine, Keechi, Butler, Grand Saline, Steen and Brooks, are more noticeable than on any of the domes discovered in 1927. F. E. Poulsen, of the Pure Oil Co., who examined the area before the deep tests were drilled, noted the alignment of erratic surface dips which suggested faulting, especially in conjunction with slickensiding, and the local deflec-

Jan 1, 1928

By O. Mellgren, A. M. Gaudin, P. L. De Bruyn

In the January 1956 issue: TP 4137B. Adsorption of Ethyl Xanthate on Pyrite. By A. M. Gaudin, P. L. de Bruyn, and Olav Mellgren. P. 65. Since P. L. de Bruyn is now a member of the AIME, the word "associate" should be removed in describing his status. The address of the third author, Olav Mellgren, should read: 74-2 Chingola, N. Rhodesia. P. 68, second paragraph, last line: the word "300-fold" should be replaced by "3000-fold." Also in the January 1956 issue: TP 4158B. Energy Transfer by Impact. By R. J. Charles and P. L. de Bruyn. The authors wish to express their disapproval of the omission of the abstract from the article, since they believe that an abstract fulfills a very important function in every paper.

Jan 1, 1957

By George A. Jr. Dornin

A TRULY sound ingot can be made only from steel that is completely deoxidized. Given this condition, there is one further basic requirement-the steel in the ingot must solidify progressively from the bottom to the top. Any method of making the ingot that produces this type of solidification will yield sound products. Since a big-end-down ingot will not satisfy this condition, all sound steel today is produced in big-end-up ingots, the standard tool being the big-end-up mold fitted with some sort of refractory hot top. No one uses hot tops from choice, be cause of the bother and expense involved and because of the low yield resulting from their use-they are used because there has been no alternative where sound steel was required.

Jan 1, 1947

By L. C. Snider

NO important discoveries of petroleum during 1932 are reported from Canada. New Brunswick, which has a small production from one field, was inactive, and the production showed a decline from 6600 bbl. in 1931 to about 6300 bbl. for the year 1932. The old fields in Ontario increased from 123,000 to about 131,000 bbl. Alberta showed a decline of more than one-third, from 1,413,631 bbl. in 1931 to about 913,000 bbl. in 1932. This decline was due principally to the restrictions placed on the flow of gas wells in the Turner Valley field, from which the crude naphtha is obtained that accounted for more than 93 per cent of the production of Alberta and for more than 80 per cent of the production of all Canada in 1932. The starting of new wells to the limestone that produces the naphtha-bearing gas was prohibited late in 1931, and only wells started before that time were finished during 1932. One well was drilled in the Turner Valley field to a depth of 7555 ft., establishing a depth record for Canada. It passed out of the Madison limestone at 5560 ft., and encountered showings of oil in the underlying formations, probably of Devonian age. Commercial production had not been established by the end of the year. Commercial oil wells were brought in in two areas in Ontario which had previously been considered as productive of gas only— in the Dawn gas field, Lambton County, and in Raleigh Township, Kent County. The discovery wells had initial productions of about 50 bbl. per day, but no production of major importance is indicated. In Alberta, outside the Turner Valley district, two wildcats were drilled northwest. of Lethbridge in the Keho Lake vicinity. Both failed to make commercial producers in the Madison limestone, but one was testing upper sands at the close of the year. Good showings of oil are reported. A very small production was found in the Madison limestone in a wildcat well on the Twin River structure southeast of Lethbridge and another well has been started near by on what is considered on geophysical evidence to be a better location structurally. About 15 locations were made on the Canadian side of the border north of the Cut Bank development in Montana.

Jan 1, 1933

By Frank Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper, wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength; consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig.1 was drawn.

Jan 1, 1928

By Frank W. Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength, consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig. 1 was drawn.

Jan 1, 1928

By John A. Prof. Church

ONE of the most striking phenomena connected with the mines on the Comstock lode is the extreme heat encountered in the lower levels. This heat is not due to the burning of candles, heat of the men, and decomposition of timbers, all intensified by bad ventilation, as was the case nearer the surface. It proceeds from the rock, which maintains constantly a temperature very much higher than the average of the atmosphere in Nevada. The heat of these mines is a matter of more than usual interest, for they are the only hot ones now worked in the United States, and both in the present temperature encountered and in the increase which is to be expected as greater depths are reached, they appear to surpass any foreign mines of which we have a record. Hot mines are known also in other countries, as in the tin and copper lodes of Wales, where one of the veins worked by the United Mines is known as the hot lode. It has springs which discharge water at a temperature of 116° Fahrenheit, the depth being 220 fathoms, or 1320 feet. The heat of the air in these workings is given at 100° to 113° Fahrenheit. The air is bad, and the heat in the drifts seems to be traceable to defective ventilation rather than to the real necessities of the case. Air is supplied through a small pipe, and is drawn from a place where the temperature is 95° Fahrenheit. Under such circumstances it is not surprising to read that in this hot mine the air is hotter than the rock, a state of things which I have never observed in the Comstock. Other mines have been reported to the British Coal Committee as having temperatures of 106° Fahrenheit and thereabouts, but the only positive comparisons that are available at this writing are the following, all from Cornish mines * Read by permission of Lieut. Geo. M. Wheeler, Corps of Enginerrs, U. S. Arm J, in charge of U. S. Geographical and Geological Surveys, west of the 100th meridian.

Jan 1, 1879

By E. W. Parker

Anthracite, as sent to market, comes under three general terms of description: characteristics, source and size. Anthracite is generally classified as white ash, red ash, or Lykens Valley. The white ash coals are sometimes further described as "hard" or "free-burning." Lehigh white ash would come under the former description and Shamokin white ash under the latter. As a rule, it may be said that the nearer the origin of the coal to the western extremity of the anthracite region, the softer and more free-burning it is. Indeed, for many years the coal from Trevorton, at the western tip of the Middle Western field, was classified as "semianthracite" in the shipment reports. Lykens Valley coal is always a red ash coal, with a higher volatile content than the general run of anthracite, and consequently free-burning. The name does not exclusively indicate the neighborhood in which the coal is dug, but rather refers to the beds from which it is obtained. These beds lie, not above the Pottsville conglomerate, as is the rule, but encased in it. The extreme eastern limit of the Lykens Valley beds would seem to be about Tremont, in Schuylkill County, and the Natalie mine, near Mount Carmel. There are, of course, traces of these beds farther to the east, but they do not seem to be workable. There are as many as six of the Lykens Valley measures found in the conglomerate at some points, but to a large extent they are unworkable. Whether this coal is obtained in the Lykens Valley proper, where the beds were first identified, or from the Shamokin Valley, it is always Lykens Valley coal, and it has long been considered a premium coal, especially desirable for domestic use, particularly when a quick, hot kitchen fire is desired. Coals are, of course, frequently marketed under special names—Jeddo, Scranton, Kingston, Old Company Lehigh, Famous Reading, Lacka-wanna, etc.—which, of course, have the trade significance which their producers and vendors have built up. General Description of the Various Coals, with Name of Seam and Producing District This is partly covered in the paragraphs above. Lykens Valley coal is produced from one or another of the six Lykens Valley beds lying within

Jan 1, 1930

By E. Alan Haley

Accurate and economic control of line and grade on long tunnels, large structures, excavations and waterways has been a problem to surveyors and engineers for decades. The conventional method of surveying, incorporating a level, transit and a number of surveying technicians, has proven to be a very expensive and time-consuming operation. Now, however, engineers have adapted the laser to help ease the problems of surveying, at the same time increasing the efficiency of such operations. The laser, which projects a continuous, narrow red beam of brilliant light, provides a constant alignment reference that does not interfere with personnel or equipment. A complete laser alignment system, specifically designed for and suited to a variety of mining and tunneling operations, has been developed by the Perkin-Elmer Corp. The engineering significance of this development can be fully realized when it is noted that, aside from potentially tremendous economic advantages in terms of labor savings, the laser beam provides a system of alignment that is at least ten times more accurate than presently used optical systems. The new laser system provides accuracies within 10 microinches per foot (1 x 10-5in.) when used with an accessory centering detector. In one of its first field trials, the laser was used for alignment of a two-mile tunnel which showed a total deviation of less than 5/8 in.

Jan 4, 1968