Search Documents

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table 1 may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of an 0 is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true

Jan 1, 1940

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division, and revised in 1939. Generally in Table 1 the unit for prescntation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions—several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and /or commercial value. As to each spacc in the tabulation, it is citller (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are detcrminable but not detcrminable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries arc not subject to precise determination. In such rases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1939

By D. C. Jillson

THE data on the critical resolved shear stress for zinc single crystals published by Rosbaud and Schmid1 showed many irregularities, as seen in fig. 1. There have been subsequent investigations,2,3 but no one has repeated this work with a wide range of orientations, with specimens of a higher degree of purity and perfection, and with improved experimental techniques in order to determine whether these variations were entirely experimental or whether they might have been due, at least in part, to some feature of the mode of deformation not known or understood. Mathewson4 and others have long felt that the glide observed in a [100]* direction between two (001)* planes in the zinc lattice might be actually the net effect of many consecutive unit glides or movements in two alternating [210] directions (fig.

Jan 1, 1951

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke's paper is published in full as it shows clearly the good results of the Institute's work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke's paper is published in full as it shows clearly the good results of the Institute's work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By W. C. Knoblaugh

Rotary kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150ºF., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to 175,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. Firing with Pulverized Coal Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers .on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1948

By W. C. Knoblaugh

Rotary kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150ºF., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to 175,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. Firing with Pulverized Coal Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers .on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1948

By Frank A. Herald

Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-—several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and /or commercial value. As to each space in the tabulation, it is either (I) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use 2. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations may be involved, our figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Wile we have not provided a column for showing the thickness of the productive zone, generally the difference between average depth to bottoms of productive wells

Jan 1, 1935

By J. S. Ll. Leach, L. R. Rubin, M. B. Bever

The energies of formation of ordered and disordered solid solutions of composition CusAu and the energy of ordering in this alloy were determined by tin solution calorimetry. The degree of order was measured by X-ray diffraction and electrical resistance and microhardness measurements were made on ordered and disordered specimens. AMONG the phenomena associated with the order-disorder transformation of a solid solution, the change in internal energy is of special interest because of the part it plays in the various theories of ordering. Published values for the decrease in internal energy accompanying the formation of a superlattice from a disordered solid solution of composition CuAu range from —370 to —2260 cal per gram-atom. Some of these values represent calculations based on theory and others are the results of experimental measurements. The distinction between the change in internal energy, AE, and the change in enthalpy, AH, can here be neglected, because they are approximately equal for solid-state reactions at normal pressure. An analysis of ordering by Bragg and Williams' predicts an energy change of —605 cal per gram-atom for the formation of a superlattice in the alloy Cuau from a completely random solution. Peierls" application to Cuau of Bethe'sb earest-neighbor theory yields —560 cal per gram-atom for the formation of a superlattice from a matrix which initially contains short-range order. Cowley' extended the nearest-neighbor approach to include as many as five shells of neighbors; on this basis a change in energy of —500 cal per gram-atom is expected. Eguchi," using a quantum-mechanical treatment, calculated a value of —2260 cal per gram-atom for the difference in the energy of completely disordered and completely ordered Cu,Au. Sykes and Jones- eated a completely ordered alloy and measured its heat capacity as a function of temperature. This measured heat capacity agrees closely with the corresponding value found by the Kopp-Neumann (or mixture) rule up to about 250°C and above this temperature exceeds it, especially near the critical temperature for ordering. The difference between the integrals with respect to temperature of the observed and the Kopp-Neumann heat capacities was considered to be the energy of ordering. By this method Sykes and Jones found a value of —530 cal per gram-atom. This value is not adjusted for the short-range order remaining above the critical temperature. The pres- ence of such short-range order is suggested by the difference between the measured heat capacity and the extrapolated Kopp-Neumann heat capacity immediately above the critical temperature. Values reported by Weibke and von Quadt' and by Hirabayashi, Nagasaki, and Maniwaa were obtained in the course of investigations primarily aimed at other objectives. Weibke and von Quadt measured the temperature coefficient of the electromotive force of a Cu-CuAu cell. They obtained a value of —1010 cal per gram-atom for the heat of formation of the alloy at 500°C, at which temperature there is no long-range order. They also obtained —1380 cal per gram-atom as the heat of formation of the ordered alloy at 370°C. Considering the heat of formation of the disordered alloy to be independent of temperature, they estimated the energy of ordering at 370°C as —370 cal per gram-atom. At this temperature long-range order is incomplete and the degree of order changes rapidly with temperature. Hirabayashi, Nagasaki, and Maniwa," using an annealing calorimeter, investigated an alloy containing 23.4 rather than 25.0 atomic pct Au and thus could not obtain complete order. Thelr value of the energy of ordering was —490 cal per gram-atom. Orianis has recently investigated the Au-Cu system by the galvanic emf technique. He reports values for the heats of formation of Cu-Au alloys, from which the heat of formation at 427 OC of an alloy of composition CuAu may be found by interpolation. This value is —1080 cal per gram-atom. In the work here reported, disordered and ordered alloys of composition CuAu and corresponding mixtures of gold and copper were dissolved in liquid tin and the heat effects measured. These heat effects are small, since the dissolution of gold in tin is exothermic and the dissolution of copper is endothermic. The method, therefore, yields fairly precise values of the heats of formation of disordered and ordered alloys and of the energy of ordering. Experimental Procedure The calorimeter consisted of a long-necked Dewar flask immersed in a constant temperature salt bath and has been described by Ticknor and Bever." The chief changes in this equipment were an improvement in vacuum and the replacement of the mercury thermoregulator by a resistance thermometer control circuit. The solvent, which was maintained at a constant temperature near 350°C, consisted of 500 grams of 99.99 pct pure tin. The solute samples were mixtures of gold and copper in the proportion corresponding to the composition Cu,Au or solid solutions

Jan 1, 1956

By J. W. Borough

THE electrical conductivity of pure copper is markedly decreased by small amounts of impurity in solution. The magnitude of this effect has been very carefully determined by numerous investigators who studied a wide variety of impurity elements. Much of this work is summarized in an excellent review by Pawlek and Reichel.' The case of zinc impurity in copper is an exception to the above in that there has been no well-documented study of the effect using high-purity starting materials. The values for the effect of zinc on conductivity, which are usually taken from unpublished work by Skowronki, indicate that zinc in low concentration has no effect whatever in lowering the conductivity of pure copper. This effect, if true, is unusual since it is generally known that even in lowest concentration, impurities exert an effect on conductivity which is proportional to the amount dissolved. It is more reasonable to suspect that in the original work on the effect of zinc some of the zinc was oxidized out of solution during specimen preparation. The following experi- and calculated d-spacings based on the unit cell dimensions of Baenziger et al. Since the single crystal studies of Baenziger et al. were limited to (hk0) and (hk 1) data, it was not possible to Compare all the intensities of the powder and single crystal patterns. However, the strongest reflections of both studies, the (321) reflection, agree very well when the appropriate multiplicity factor is used. Good agreement was also found in a number of other reflections of lesser intensity. Despite the precautions taken in annealing the U6Fe powder, an appreciable amount of UO, was detected in the powder pattern after heat treatment. The powder pattern reported by Groganoand Clews is given in Table I. Except for the 3.15A line, which is the strongest line of UO,, their pattern, as far as it goes, compares favoEably with the data from this study. Gordon and Kaufmann have reported a diffraction powder pattern purported to be U, Fe but it bears very little resemblance to the patterns of Table I. ments were carried out to redetermine the effect of zinc on conductivity using high-purity starting materials and processing conditions capable of producing oxygen-free alloys. Materials used in the experiment were ASR 99.999 pct Cu and Cumingo 99.999 pct Zn. Four 1 lb melts were prepared with identical procedure in argon atmosphere with crucibles made from Speer No. 580 graphite. The compositions were 0.0, 0.1, 0.3 and 1.0 pct Zn. Standard No. 14 wire (0.064 in. diam) was made from these melts as follows. The 1 pct Zn sample was first reduced 94 pct by cold swaging with five annealing treatments of 800o for 10 min in hydrogen between swagings, and then reduced 94 pct to the

Jan 1, 1962

By F. J. Darnell

SINGLE crystals of a-titanium are difficult to obtain because of the phase transformation at 882 °C in which the structure changes from the high-temperature body-centered structure ß to the low-temperature hexagonal close-packed structure a. Preparation of single crystals of a-titanium has previously been accomplished by a strain-anneal method which takes several days and is not generally reproducible. Single crystals as large as 5 mm

Jan 1, 1959

TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN: Herewith are submitted the report of the Treasurer for the year 1936 and the reports for the same year of the following committees: Admis¬sions, Membership, Papers and Publications, Library, Student Relations, and MINING AND METALLURGY. To these reports you are referred for details of the year's activities. Finances.-Income for the year was $173,091 including an appropria¬tion of $2500 from the Rocky Mountain Fund earmarked to defray expense for official visits to western Sections and student societies. This compares with $141,754 in 1935 and exceeds by more than $50,000 the income of 1933 wherein the low point during the depression was reached. The major items of increase were: $6,700 from current dues; $10,600 in initiation fees and dues of newly enrolled members; $10,800 from the monthly magazine MINING AND METALLURGY. Sundry small declines were offset by minor increases. Expenditures for the year totaled $176,007 compared with $148,361 in 1935. Major increases were $5,700 for MINING AND METALLURGY; $4,000 for TRANSACTIONS and TECHNICAL PUBLICATIONS; $1,500 for meetings; $1,300 for Local Section appropriations; $6,500 for Technical Division expense; $5,000 for Increase of Membership expense; and $2,500 for visits to Local Sections and educational institutions. Comment on several of these items will appear under subsequent heads. Net deficit for the year was $2,915, this sum being made up from the accumulated surplus. It is interesting to observe that the net excess of income over outgo for the five-year period 1932-1936, inclusive, is $760. Membership and Dues.-During the year there was a net gain in membership, including Members, Associates, Junior Members and Junior Foreign Affiliates of 755 (from 7116 to 7871). In addition there was a gain of 616 in Student Associates (from 1004 to 1620). Taking account of small losses totaling 5 in the other grades, the net increase was 1366 bringing the total to 9607, the highest figure reached in the history of the Institute except at the end of 1921 when the total was 9850. In part the gain is accounted for by the smaller number lost by suspension

Jan 1, 1937

By George L. Montgomery

In a recent article Heckler, Elias, and woods1 have described an automatic computer technique for plotting of pole figures. To anyone who has constructed pole figures manually from raw X-ray data, the development of computer plotting techniques has been a very welcome development. The purpose of the present note is to describe an alternative computer plotting method which, if somewhat less precise than the method described by Heckler et al., has the advantages of being faster and of not requiring the availability of a plotter. The plot is made directly by the printer of the terminal system and, by its nature, has a good deal of visual impact. Each character of output symbolizes a level of intensity. For example the numerals 1 to 9 might represent intensities referred to some reference obtained from a randomly oriented sample. Should more levels be required (this is seldom necessary) alphabetic or other characters may be used in addition. When these are arranged in the proper fashion, the result is a pole figure such as is shown in Fig. 1. It is the purpose of the computer program to transform the data and carry out the arrangement in a suitable manner. The computation is carried out on a line by line basis in order to reduce the amount of storage required and thus keep the program "small". It is, thereby, well within the limitations of the time-sharing systems which are becoming increasingly available. The inaccuracies introduced are slight and the plot can easily be made as precise as the technique used to collect the data. Comparison of pole figures produced by this method with those constructed manually shows a high degree of equivalence. To the present, the technique has been applied to reflected X-ray data only. X-ray data are collected in a manner identical to that described by Heckler et al. That is, as the goniometer rotates the specimen, a series of counts, accumulated over a preset time, is recorded. The method by which the proper symbol, representing an intensity level, is assigned to each print position is up to the ingenuity of the programmer. Perhaps the simplest method is to section the stereograph in the fashion of a polar net, and to assign all print positions lying within each segment a symbol representing the level of intensity recorded at the data point nearest to the center of the segment, see Fig. 2. The number and arrangement of the segments are selected to conform more or less with the number of accumulated counts and the geometry of the goniometer path used to collect them. Since the angular distance between accumulated counts is usually not infinitely controllable, it is impossible to locate one reading within each segment and, at the same time, maintain symmetry in the sectioning of the stereograph. This latter requirement is essential to keep the computer program simple and flexible. As an expedient it was found that the number of data points could be increased to conform with the number of segments, with very little loss of

Jan 1, 1969

There is plenty of sulphur available but not at the price currently being paid for brimstone. Immediate shortages may be felt before the market adjusts, making marginal sources and by-product sulphur and acid available. (See P. 403) Government aid for mineral exploration is available and regulations governing applications are available from The Defense Minerals Administration, Dept. of Interior. lust ask for M0-5 and also for the contract form which is MP-103.

Jan 5, 1951

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice Chairman for Production of the Petroleurn Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive, locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-—several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert 2; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are deter-minable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use 2. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations may be involved, our figures should represent as nearly as possible the total quantity of gas removed from the reservoir.

Jan 1, 1936

By A. D. Dorenfeld

Factorial design is a mathematical method of drawing valid conclusions from a series of tests made in a predetermined pattern. It is applied to flotation ore testing using, in this case, five variables, each varied twice, requiring a total of 32 tests. Representative conclusions are checked by repeat testing. THE factorial design method of testing is particu-J- larly applicable to mill-scale plant tests because 1—the conclusions take into consideration all variabilities of the plant, 2—there are no subjective guesses as to the conclusions, 3—the number of tests necessary to check large numbers of variables are at a minimum, and 4—interactions between variables can be discerned. It is equally applicable to laboratory testing because once the variables to be investigated have been decided upon, as well as the number of levels for each variable, a well-trained assistant can run the tests, since the test work follows a predetermined mathematical pattern, leaving the conclusions to be found by the person in charge. The conclusion takes into consideration all errors of the tests. To illustrate the use of factorial design, a sample of copper porphyry ore was tested, the copper content of the batches not being uniform. Five variables were investigated, each at two levels, requiring only 32 tests. After suitable arithmetical analysis, conclusions for copper recovery and concentrate grade are arrived at. Four cases of these conclusions are checked by repeat testing. Testing Methods Reproducibility of flotation tests varies widely, depending on the experimenter, the process, the equipment, and probably a host of unknown and perhaps interacting variables. If the reproducibility of tests is good, let us say to 0.2 pct recovery of a certain metal, and the minimum difference between tests upon the variation of the interested variables is, say 1 pct, then simple averaging and inspection is ample in interpreting results. However, often such a happy situation is not the case. This is particularly true in mill-scale operations where the ores are variable, and a host of minor operating fluctuations common to most milling, and familiar to all mill operators, is the normal state of affairs. Yet, mill scale tests are run, the results averaged, and conclusions drawn therefrom. The trustworthiness of such results should be measured by comparison to the experimental error—the measure of the degree of reproducibility of the results. This comparison is a test of significance. Thus, if daily results of recoveries average 80.0 pct, and a spread of 78.0 pct to 82.0 pct, is recorded, then, clearly, on changing mill operations, an 81 pct recovery cannot be construed as significant by using averages, since it is well within the previous test limits. By using rigorous statistical tests of significance, conclusions arrived at by inspection or simple averaging may be shown to be based on inadequate evidence or even wrong. In any event, a plant super-

Jan 1, 1952

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice Chairman for Production of the Petroleurn Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive, locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-—several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert 2; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are deter-minable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use 2. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations may be involved, our figures should represent as nearly as possible the total quantity of gas removed from the reservoir.

Jan 1, 1936

By Karl F. Peterson, H. K. Najarian, Robert E. Lund

R. E. Powers (Mellon Institute of Industrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants' producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors' reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952

R. E. Powers (Mellon Institute of lndustrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants' producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors' reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more ,or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952

By J. P. Carson

(Read at the Wilkes-Barre Meeting, May, 1877.) THE works of the Tula Iron Company are in the Republic of Mexico, State of Jalisco, twenty-eight leagues southwest of Guadal¬ajara, ten leagues northwest of the town of Sayula, through which passes the projected line of the Mexican National Railroad. Its geographical position would be about: latitude, 20° 10' N., longi¬tude, 4° 35' W. of Mexico City. The surrounding country is a roll¬ing plateau, 6000 feet above the sea, enjoying the most magnificent climate in the world, the average temperature being about 70°. The works were commenced in 1850 by a company with very small capital, having not the least idea of the undertaking. They soon fell into the hands of the money-lenders, and after changing

Jan 1, 1878