Search Documents

By Pol Duwez, Paul Pietrokowsky

Titanium and vanadium form a complete series of solid solutions at temperatures above 885°C. Below 885°C, vanadium is slightly soluble in a titanium (about 1.5 pct V at 650°C) and a two-phase a plus ß region extends to 18.5 pct V at 650°C. The alloys up to 15.0 pct V transform into a supersaturated a solid solution upon rapid cooling from the ß phase. Above 15 pct V the ß phase may be retained. The temperature at which the ß to a' martensite-type transformation takes place decreases steadily from 850°C for 0.5 pct V to 325°C for 12.7 pct V. IN the transition series of the periodic table, the six elements that have a body-centered cubic structure at all temperatures, namely chromium, vanadium, molybdenum, columbium, tungsten, and tantalum, fulfill the conditions required for the existence of complete series of solid solutions with the high temperature (ß) form of titanium. Up to the present time, complete solubility at temperatures above the a to ß transformation of titanium has been observed in the systems Ti-MO,1,2 Ti-Cb,2 Ti-W,³ and Ti-Ta.³ The two remaining elements, vanadium and chromium, have atomic diameters which are not as near that of titanium as the atomic diameters of the four other elements. Both are smaller than titanium and the difference, expressed in percentage of the titanium atomic diameter, is 12.3 pct for chromium and 8.2 pct for vanadium. On this basis, the least favorable conditions for solid-solution formation are therefore encountered in the Ti-Cr system. The early work on the Ti-Cr system4 revealed that up to about 1100°C the solubility of chromium in ß titanium is limited, and an intermetallic phase exists near the stoichiometric composition TiCr2. It was found later' that a continuous series of solid solutions extends across the diagram at higher temperatures, and TiCr2 forms by solid state reaction. It became apparent therefore that complete solubility would also be present in the Ti-V system. The present investigation confirms this possibility. The iodide-refined titanium used in this investigation was purchased from the New Jersey Zinc Co., New York. According to the manufacturer, a typical analysis of this product is 0.0065 pct Mn, 0.0022 pct Fe, 0.0015 pct Cu, and 0.0042 pct Pb. The Vickers hardness number (10 kg load) of the crystalline bar varies between 55 and 80. The vanadium metal was purchased from the Westinghouse Electric Corp., Lamp Div., Bloomfield, N. J. The purity of this metal is probably above 99 pct V. The oxygen content must have been quite low, since a bar about 1/4 in. square could be cold rolled into a ribbon 0.020 in. thick. To prepare the various alloys on the titanium-rich side of the diagram, the titanium rod was machined into cups 1 cm in diam and about 1.5 cm high. Pieces of vanadium, of the proper weight, were cut from the square bars and placed within the cups prior to melting. On the vanadium-rich end of the diagram, single pieces of the metals, in the proper weight pro-

Jan 1, 1953

By Earl Oliver

CONTENTS PAGE A.I.M.E. Stabilization Committee Activity 3 Definition of Capture Rule: Robert E. Hardwicke 4 Westmoreland Natural Gas Co. vs. DeWitt 5 Kelly vs. Ohio Oil Co 5 Bernard vs. Monongahela Gas Co 6 Definition of Ownership in Place 7 Prospective Stabilization Remedies 7 Dean Roscoe Pound's Four Tests of Practicability 7 I: Mechanically Feasible 8 Capture Rule 8 Ownership in Place 10 Mechanical Separation Method 10 Engineering Appraisal Method. 11 II. Economically Advisable. ., . 13 Capture Rule 14 Ownership in Place 14 III. Politically Wise 14 Capture Rule 14 Ownership in Place 17 IV. Legally Sound 18 Capture Rule 18 Ownership in Place 19 Dean Henry M. Bates' Analysis 19 Resume 22 THE A.I.M.E. Stabilization Committee was named in 1932 to ascer-tain whether some practical substitute could be devised for the Rule of Capture, which was generally credited with being the major cause of instability in the Petroleum Industry. After considerable intercommittee correspondence a letter was received from. E. DeGolyer under date of Jan. 25, 1935, in which he discussed the possibility of modifying rather than discarding the Rule of Capture. He summarized his proposal as follows:

Jan 1, 1937

HOW the Engineers' Memorial clock and carillon at Louvain has impressed the people of that city is indicated by the following letter sent by the Secretary of the University of Louvain to the Secretary of the United Engineering Society. We are still full of the memories of that splendid July 4, when we came into such .delightful contact with our American friends and more specially with the representation of the engineering societies of the United States. It was a great joy for all the members of the University to see those, American friends who have given to us such a splendid memorial in honor of- the brave men who fell in the Great War.

Jan 1, 1928

By H. J. Rose

SIXTY-FIVE million net tons of coal were carbonized in the by-product and beehive coke ovens1 of the United States during 1924. This tonnage represented 13.4 per cent. of the bituminous coal which was mined in that year. Table 1 shows production and disposition.2 TABLE 1.-Production and Disposition of Oven Coke in 1924 BY-PRODUCT BEEHIVE TOTAL Coal charged into ovens, tons 49,061,339 15,914,310 64,975,649 Coke produced (exclusive of screenings and breeze), tons 33,983,568 10,286;037 44,269,605 Average yield of coke, per cent 69.3 61.6 68.1 Disposition of coke: PER PER PER CENT. CENT. CENT. Blast furnace 82.5 82.8 82.6 Foundry 4.6 13.3 6.6 Domestic 8.3 1.4 6.7 Water gas manufacture and all other uses 4.6 2.5 4.1 Cokes having somewhat different combinations of chemical and physical properties are desired for the various uses listed above, and these properties depend primarily upon the types of coal used. American coals have a wide range of purity and coking quality, and the chief subject of this paper will be the selection of coals for the manufacture of blast furnace, foundry, domestic, and water-gas coke, in by-product coke ovens. It will obviously be necessary to include a discussion of those physical and chemical characteristics that are generally considered essential or desirable for each type of coke.

Jan 7, 1926

By A. Soundraraj, S. Singh, R. C. Deshpande

THE detonation of a high-explosive charge having a metal-lined conical cavity (shaped charge) results in a fast-moving jet and a slow-moving slug.1-4 Clark and Bruckner reported the metallographic studies of a cast-iron slug. The present note describes the metallographic studies of a copper slug and discusses the principle of flow involved. The shaped charge consisted of a 5-cm diam cylinder of cast high explosive (60-40 RDX-TNT mixture) having a 45 deg and 0.16-cm thick copper cone. The copper (99.5 pct purity) had a grain size of 0.06 to 0.08 mm diam and a hardness of 65 to 75 Hv. These were fired into a deep container of water and the slugs were recovered undamaged. The longitudinal and transverse sections of the slug were polished, etched, and examined for mi-crostructural changes. Macroexamination revealed a radial grain flow inwards towards the center and a downward component of flow towards the base of the slug. Fig. 1 shows schematically the micro-structural changes observed on the longitudinal section of the slug. The region D near the apex and also along the outer surface of the slug was characterized by the presence of heavily deformed and twinned grains. Some of the grains were having bent or crossed twins, Fig. 2. The grain size in this region was of the same order as that of the

Jan 1, 1960

By S. B. Twiss, P. R. Basford

The relationship between areas of iron powders, briquettes, and sintered compacts and tensile strength has been determined. It has been found necessary to distinguish between two types of areas which exist in such powders—a macroscopic area due to the shape and size of particles and a microscopic area due to pores and cracks in the surface. Only the macroscopic area, specifically the area due to particle irregularity, contributes to tensile strength; the microscopic area cannot be forced into contact with adjacent particles ond does not participate in bond formation. Of the two methods of area measurement employed in this study—permeability to liquids and gas-phase adsorption—only the former is useful for determining the roughness factor. A measure of this roughness, (area measured by permeability to liquid) -f- (orea of powder with the same size distribution, but made up of spherical particles), is shown to be uniquely related to tensile strength at constant density. The other important factors in determining the strength of sintered-metal compacts are the density and presence or absence of surface oxide. THE manufacture of metal parts by the process of powder metallurgy is an important and rapidly growing industry. Progress has been rapid and continuous, largely because of the excellent research in the field. Nevertheless, the process remains inherently complex and empirical. Several investigators have shown that the properties of the final compact must depend on many variables; namely, shape,' size distribution,"-" nd compositiona of the original particles, the pressure necessary to compress to the desired density, the density of the compact, the time and temperature of sintering, and so on. Through the application of some new techniques to the study of powders and compacts, and the correlation of a number of observations of known variables, the present paper attempts to clarify and simplify the underlying theory of the powder-metallurgy process. Any theory must start with the obvious fact that the strength of a compact, its most useful property, is due to the formation of welded areas between adjacent particles, and attempt to deduce what effect other variables will have on (a) the area and (b) the intrinsic strength of these welds. Such welded areas can be demonstrated by electron micrographs, as in Fig. 1. It was believed that (a) could be most directly studied by means of surface-area measurements on the original powders and on the compacts made from them; the area decrease should be related closely to the welded area. A representative group of eleven iron powders from commercial sources, and made by a variety of processes, was chosen for this study. In addition to the surface-area measurements, correlations were established between the tensile strength and all the known variables which might possibly affect it. The results are quite unexpected. They indicate that the situation is much simpler than the authors had anticipated. The strength of the sintered compact is determined, indeed, by no more than three variables; viz., the irregularity of the original particles, the density of the compact and, in exceptional cases, the amount of surface oxide. All three had been recognized previously as having some effect on the tensile strength, but in the absence of the special techniques and interpretations to be developed here, there could be no suspicion that they were the only relevant variables. Materials and Methods Material—All the iron powders were commercial products obtained from the Amplex Division of Chrysler Corporation. Powders A, B, C, and J were very pure electrolytic iron. Powder D was made from oxidized scrap reduced by heating with an excess of cast iron. Powder E was a high-grade iron ore reduced by hydrogen. Powder I was prepared by atomizing molten cast iron in an air blast, quenching the droplets in cold water, and crushing the coarse powder. Mill scale (oxide) is added and the mixture heated to reduce the high carbon content. The other powders were all prepared by reduction of iron oxides, such as mill scale. They

Jan 1, 1959

By A. G. McGregor

DURING the past 5 years, five new copper-smelting plants have been built and put into operation in the State of Arizona. The monthly copper output from these plants averages from 5,000,000 to 18,000,000 lb. Previously, there never was as much activity in copper-smelting plant construction in the same length of time in all the rest of the world. Naturally, in this amount of work, some new problems were met and new features in plant design and. equipment developed. Some of these features are described in this paper. CONCENTRATE HAULING, UNLOADING AND SAMPLING SYSTEM (a) Concentrate Car The International Smelting Co. has provided at its plant at Miami specially designed cars for hauling the concentrates from the mills of the Inspiration Copper Co. and the Miami Copper Co.. The car has a bottom that is readily made tight to hold flotation concentrates and is quickly and cheaply unloaded. Figs. 1, 2 and 3 show views and details of the car. The main feature of this car is the slot in the bottom throughout its length, which is closed by means of short planks that overlap like ship-lap as shown by Fig. 1. At one end of the car an iron gate operated by a screw and hand wheel is provided, which clamps or presses the planks together, making the bottom tight. A removable tapered plug rests vertically over this gate when the loading of the concentrates at the mill commences.

Jan 8, 1916

By William Phillips

THE possible sources of potash salts in the United States have been considered from many points of view during the last several years, but it is only within the last two or three months that the situation has become acute. We import from Germany, the only source of large supply, more than $10,000,000 worth of potash salts annually, and this business has been badly crippled by the European war. If there was ever a time in our industrial existence when the necessity of providing for our own needs was more acute than it is now, we are not aware of it. One has only to study the price, lists of chemicals sent out by the large supply houses to see the change wrought within a very short time. Whether or no these prices are to maintain for a considerable time, no one can say; but it appears to be probable that we shall not see prices materially lower for a period of uncomfortable length, to say the least. It is not my purpose at this time to discuss the various sources of supply of potash salts that have been suggested or recommended. Some of them might afford a pleasing relief but all of them combined would not affect the situation seriously. If we are to have our own sources of potash salts, they will have to compare, in some efficient manner, with the sources upon which we have drawn during the last 20 or 30 years; i.e., they must exist-in minable quantities. It seems to me to be quite idle to speculate upon our domestic sources of potash if those sources are not of a character similar to those upon which we have so long depended. A few thousand or, perhaps,, a few hundred thousand dollars' worth of chemically derived 'potash may be produced under the stress of present conditions, but when we consider that each year demands more than $10,000,000 worth, we must look to underground sources; we must look to mines similar to the famous Stassfurt and Halle deposits. If we cannot mine potash salts, we shall have to do without them for a while.

Jan 2, 1915

By AIME AIME

COMMITTEE No. 2 of the Iron and Steel Institute b f Great. Britain has presented its first report, of 27 printed pages, on blast-furnace plant and practice. This report outlines the various features of modern blast-furnace practice with brief comments thereon, and with references to some of the more recent methods devised for applying the principles and attaining the purposes aimed at' under these headings.. In general, the trend in the United States is in the direction of larger and larger furnaces with ever increasing capacity from which, with improved details in methods and equipment, and attention to details of management, considerable progress in. economy of production has been attained, in fuel consumption and in other items of production cost.

Jan 1, 1929

Department of Forestry and Geological Development, 435 State Capitol, Atlanta, Ga. S W. McCalhe, State Geologist. A complete list of Bulletins of the Geological Survey of Georgia will be sent upon request. Forty-five Bulletins have been issued, most of which deal with the mineral deposits of the state and are still available; they may be had on payment of postage. The subject matter of those bulletins of most interest is indicated in the following list, with the year of issue and the mailing weight. Bulletin 1, Marbles (1894), 3 lb , 8, Road building materials (1901), 3 lb , 9, Granites and gneisses (1902), 2 lb ; 10, Iron ores (1900), 2 lb , 11, Bauxite (1904), 2 lb.; 12, Coal deposits (1904), 2 lb ; 13, Ocher deposits (1906), 2 lb.; 14, Manganese deposits (1908), 2 lb ; 17, Fossil iron ore (1908), 2 lb.; 18, Clay deposits

Jan 1, 1933

By H. B. Heller, T. J. LaChapelle

Phosphorus nitride has been used as a diffusant for introducing phosphorus into silicon under various conditions. It has a temperature -dependent rate of decomposition beginning in the 500°C range, increasing very rapidly above 1000 C, producing gas -eous phosphorus and nitrogen. Best control was obtained with a two-temperature arrangement, with silicon at the proper higher diffusion temperature. It is an easier compound to use than the usual P2O5 because it is nonhygroscopic and yields temperature-controlled surface concentrations together with excellent final surfaces. Surface doping nearly as high as that produced by phosphorus pentoxide has been observed for sources at 850" to 900°C. Reproducible high sheet resistances were obtained by using slow flow rates (1 linear in. per min) and staggered-baffle gas mixing with the nitride at 550°C. Both inert gas (argon, nitrogen) and oxidizing ambients have been examined. Oxygen reacts to produce anhydrous P2O5, consuming the source at a rapid rate. Nitrogen, except for short diffusion times, suppressed the dissociation reaction and sometimes produced inferior surfaces. Argon appears to be a more useful ambient. PHOSPHORUS is a common impurity atom which may be introduced into a semiconductor lattice to create a p-n junction or an nn contact region. Various investigators1-4 have described techniques which can be used with either elemental phosphorus or certain of its compounds. This paper discusses a newly available compound of phosphorus, phos- some processes silicon wafers are precoated with a phosphate glass which acts as the doping source. Although a nonoxidizing form like elemental phosphorus or a phosphine can be used, most diffusion methods usually involve the use of phosphorus pentoxide. Because of the rapid volatility of this compound, a two-step process is often used, combining a gaseous deposition to introduce a predetermined quantity of phosphorus into the silicon with a later redistribution to obtain the desired distribution and surface concentration. Such a process usually involves predepositing phosphorus at surface concentrations greater than 1020 cm-'. At such doping levels the phosphorus-diffusion coefficient appears to be strongly concentration-dependent.596 Distribution profiles5'9 for these high concentrations of phosphorus do not follow Fick's laws, having extended subsurface regions which appear electrically to be nearly uniformly doped with ionized impurity atoms. Radioactive-tracer experiments also show near-surface anomalies in the distribution profile. Additionally, it has been shown1' that the introduction of very high surface concentrations of impurity atoms into silicon (a step necessitated by the subsequent lowering of concentration during the redistribution) creates dislocations, even in material having no dislocations originally. For device fabrication the use of oxide masking introduces certain difficulties and limitations.7'8 The standard practice of using phosphorus pentoxide as an impurity source adds other problems to these because of the speed and ease with which this compound reacts with moisture present in any gas in contact with it. In fact, P2O5 is one of the fastest and most effective drying agents for gases. Because it is such an excellent desiccant, completely anhydrous phosphorus pentoxide is difficult to obtain and is even more difficult to keep dry. Adequately dry gloved boxes must be used for storage and transfer of the chemical. The presence of even traces of moisture will cause formation of phosphoric acids which, during the high-temperature diffusion, results in polyphosphoric acids of variable composition. Such reaction by-products end up as gradually accumulating viscous fluids in the cooler parts of the diffusion furnace. The calculation of the final solute distribution for

Jan 1, 1964

By George J. Young

DURing the spring of 1910 1 visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. Thc principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories. The commercial deposits are confined to the Tertiary period although

Jan 1, 1916

By George Young

DURING the spring of 1910 I visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and, even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. The principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories.

Jan 2, 1916

By J. A. Jr. Church

I. EARLY FURNACES. . COPPER blast-furnace construction in America has long recognized a general standard in the rectangular water-jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in. ; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting ; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18, ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few months by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 7, 1913

By Hiroshi Oikawa, A. G. Guy

Recent experimental evidence has shown that it is often incorrect to neglect the reactions occurring at an interface with respect to the diffusion reactions. By introducing reaction-rate constants and k for the transfer of components 1 and 2 between the a and b phases, a phenomenological description has been devised for the coupled processes of diffusion and in-terfacial reaction. An illustrative example has been analyzed with the aid of a suitable computer program. The results indicate that for kab values on the order of 10'1 cm per sec and Ð values of about 10¯10 sq cm per sec, the interfacial reactions are significant during the first 10 2 to l0 6 sec of a diffusion experiment. Among the observable effects of the interfacial reactions in this case appear to be the burying Kirkendall markers and an anomaly in the initial shifting of these markers. THE study of diffusion between two phases is especially important because of its direct connection to phase transformations. For example, the transformation of austenite to ferrite involves diffusion in the a and ý phases and also an interfacial reaction (trans formation) at the a/? interface. If ferrite and aus-tenite are the two members in a diffusion couple, the same two reactions occur during the diffusion process. The numerical values obtained for the diffusion coefficients and interfacial-reaction constants from diffusion experiments can then be employed to predict phase-transformation behavior. Refinement of the calculations of phase transformation is also suggested by the present method for treating two-phase diffusion. In the recent paper by Nolfi et al.' only the solute com ponent is considered in the interfacial reaction accompanying a phase transformation. The present analysis demonstrates that both components must be considered. It is generally recognized that reactions of some kind must occur at the interface in a two-phase diffusion couple, but usually it is assumed that the interface reaction occurs so rapidly that its effect on the overall process is unobservable because the slower diffusion process determines the kinetics of the process. However, Seith and Heumann 2 pointed out that effects of the interfacial reaction should always occur in the early stages of diffusion, and recently Eifert et al. 3 have shown that interfacial reactions influence the composition and motion of the interface in a/ß Al-Cu diffusion couples during the entire course of prolonged, high-temperature treatments. A general procedure for handling the combined processes of interfacial reaction and diffusion in a binary, two-phase system is to introduce kinetic coefficients for the interface reactions and to develop the system of equations governing the interlinked processes of diffusion and interface reaction. The resulting equations, although not amenable to solution in closed form, can be usefully manipulated by a digital computer. INTERFACIAL REACTIONS IN TWO-PHASE DIFFUSION Consider the general case of diffusion between two solid solutions, a and ß, which are adjacent phases in a binary system, Fig. 1. Two semiinfinite bars having compositions c1 and c0ß are jointed at x = 0. If concentrations are expressed in volume fraction,4

Jan 1, 1970

By Edgar Rickard

E UGAR RICKARD comes of a long line of mining men and was born at Pontgibaud, France, in 1874, where his father was then in the course of his professional work. Later his father came to California and was until his death prominently connected with milling in that state and Nevada. Edgar Rickard grew up at Berkeley, attended the University of California, graduated in 1895 from the mechanical engineering course, and remained a year longer for post-graduate work in the College of Mining. His first job was as assarer for the Mountain Copper Co., Keswick, Cal., in 1896. The following year he was assayer and surveyor for the Cornucopia Mines, Oregon. In 1898, he joined the staff of the Venture Corporation, London, and for two years made examinations for them in various parts of the world. He served as mine manager at Cripple Creek and at the Briseis tin mine, in Tasmania. From 1901 to 1905, he was general manager of the Progress Mining Co. in Lower California, but when his cousin, T. A. Rickard, bought the Mining and Scientific Press he was persuaded to come to San Francisco as business manager of that periodical. A few years later the two cousins went to London and started the Mining Magewine there as a joint venture, Edgar being the business manager. In 1915, he took over control, T. A. Rickard returning to California to devote his time to the Mining u.rbd Scientific Press. In 1917 Edgar Rickard sold out to his British associates and came home to serve in the Food Administration through the war. Rickard was one of the first of the American engineers called to his staff when Herbert Hoover began his relief work by helping stranded Americans home at the be- ginning of the war and he has been with him constantly since in the Commission for Relief in Belgium, the

Jan 1, 1929

By Willis Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep ill Johan-nesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104° at sea level, insured reasonable safety, since all parts of the machine operated At subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By Jack R. Dymond, Ronald G. Senechal, Robert O. Rye, Cyrus W. Field, Joseph F. Whelan

Metalliferous sediments are present through- out much of the ocean basins and are locally prominent in the sedimentary column on and near the Nazca plate of the east-southeast Pacific Ocean. They typically have anomalously high concentrations of the transition metals, and those on parts of the East Pacific Rise, the Bauer Deep, and other basinal depressions may contain more then 12% iron, 4% manganese, 0.1 % each of copper and nickel, and geochemically significant amounts of zinc, cobalt, molybdenum, arsenic, beryllium, silver, and possibly gold. Statistical interprerarions of chemical data indicate that most metals in sediments on the East Pacific Rise were derived from a hydrothermal component related to submarine volcanism, whereas those in basinal sediments accumulated from both hydrothermal and hydrogenous components of sedimentation. However, concentrations of the metals are controlled more by the absence of biogenic and detrital components than by nearness to centers of hydrothermal activity.

Jan 1, 1983

By J. L. Jernegan

In the summer and fall of 1875, the author was present during a short smelting campaign at the Hall Valley works, and having had occasion to make a number of chemical analyses of the ores, fuel, and fluxes, deems that the results of the same, and also an account of the smelting operations, may be found of interest to members of the Institute. The mines and reduction works of the Hall Valley Silver—Lead Mining and Smelting Company (limited) are situated at Hall Valley, Park County, Colorado. The smelting works are located about half way from the mouth to the head of the above-named valley, and the mines high up on the mountains, near its head. The three principal mines of the company are the Whale, Leftwick, and Coldspring. They are all on different veins, running parallel to one another, with a general trend from southwest and northeast. The

By Guy T. McBride

The 1970's have been considered a pivotal decade for the mineral industries. Undergraduate mineral engineering education is relevant to this theme; in particular, there are three interrelated problems: 1) The goals, and therefore the course requirements, of the under- graduate curricula are in question; 2) The unit costs of undergraduate education appear excessive to those who bear the charges; and 3) The present social ambience detrimentally affects the work attitudes and career motivation of both prospective and in-course students. Any discussion of these problems must bottom upon recognized national needs for minerals and a technologically sound minerals industry staffed by competent engineers, particularly at the exploration, development and production levels. Fortunately, these needs have been recognized and to some extent quantified, and they are even now under further intensive study by some of the most competent members of society and the profession.

Jan 3, 1973