Search Documents

By George A. Packard

The experiments here described were made under my supervision while temporarily acting as head of the Department of Metallurgy at the Missouri School of Mines, at Rolla. The work was done by Messrs. W. E. Brown, W. C. Richards, and F. L. L. Wilson, and the description of the results forms a portion of a thesis presented for the degree of Bachelor of Science. These results are submitted because I have seen no description of the application of pot-roasting to the treatment of a copper-concentrate. This work followed that already described in the discussion of the Lime-Roasting of a Galena-Concentrate,' and was similarly occasioned by the lack of a furnace of the reverberatory type in which the copper-concentrates could be smelted. The material for the tests was a mixture of three lots available. The first consisted of 8-mm. ,jig-concentrates and the second of 0.5-mm. table-concentrates, from the San Juan district, Colo. Both contained pyrite, chalcopyrite, and galena. The third was a lot of copper-ore, found in the laboratory, which had been crushed through 8-mm. screen, and had at some previous time, before the laboratory roasting-furnace was torn down, received a partial roasting. The analyses of these ores are given in Table I. In order to determine the applicability of pot-roasting as to each lot of ore, and the effect of varying proportions of lime, six preliminary tests were made in a " size N " Battersea crucible, 9 in. high by 6 in. in diameter at top, with a 5/8-in. hole bored through the bottom. The crucible was set in the upturned elbow of a 2-in. pipe, the joint being luted with clay; and air was obtained from a receiver supplied by a compressor. The

Jan 1, 1908

By Earl Hunner

IT is common knowledge that the iron orebodies of the Mesabi range lie nearly horizontal and are of trough or blanket-like types. These orebodies are from a few feet to several hundred feet thick and vary from a few acres in extent to the size of the largest one, at Hibbing, Minn., which is over 1 mile wide and 3 miles long. They are covered with sand, boulder and clay overburden and occasionally, shallow depths of ledge material, varying in total depth from about 20 to 200 ft. Large areas are not capped with overlying ledge material; the top of the ore lies directly underneath the surface material. Because of the comparatively great tonnage of ore, open-pit mining has made tremendous strides since the first open-pit ore was shipped from this range by the Merritt brothers, from the Mountain iron mine in October, 1892, and along with the great development of open-pit mining on the Mesabi range has gone a tremendous change in the character of equipment used.

Jan 1, 1930

By L. D. Jaffe

From data found in the literature, a method has been derived for calculating hardenability of titanium alloys from their composition. A single graph gives the contributions of each alloying element. These are simply added to a base hardenability for unalloyed titanium. Results agree satisfactorily with measured harden-abilities. RECENTLY the importance of hardenability of titanium alloys in permitting attainment of high strength and hardness has become apparent. If a titanium-base alloy has adequate hardenability for the section size and quenching practice used, it can generally be heat treated to high strength and hardness either by simple quenching or cooling from temperatures near the ß transus, by quenching and tempering (aging), or perhaps by direct isothermal transformation of ß1,2 If the hardenability is inadequate, high strength cannot be attained. Preliminary charts translating hardenability requirements for shapes quenched in various media into terms of Jominy end quenched hardenability specimens or ideal round sizes are now available for titanium alloys." The method proposed in 1942 by M. A. Grossmann for calculating hardenability of steels from composition has proved to be of great practical value.' It appeared worthwhile to see whether, using information available in the literature, a corresponding method for calculating hardenability of titanium-base alloys could be derived. Data No systematic experimental study of the hardenability of titanium-base alloys has yet been made. There is available, however, a considerable quantity of scattered data bearing on hardenability. Some investigators determined Jominy curves on one or several alloys. Others reported as-quenched hardness for specimens of a few alloys cooled at various rates or in various media. Still others gave the as-quenched hardness for systematically varied composition, using one or several cooling mediums. The measurements utilized in this work were limited to hardness. Strength measurements were not used because a low strength may reflect high hardness combined with brittleness. Since, in general, the hardness of titanium alloys goes through a peak as the cooling rate is varied from extremely fast to extremely slow, the cooling conditions at which peak hardness was found were taken as the measure of hardenability.1,2 When as-quenched hardness was found to drop as the content of an alloying element (believed to increase hardenability) was raised, this was taken as an indication that the cooling rate was faster than that giving peak hardness; otherwise, the hardness should go up because of solid solution hardening. Also, if the hardness increased on tempering at low temperatures, this was again taken to indicate that the cooling rate had been faster than that giving peak hardness. Many of the data did not indicate precisely the cooling conditions for peak hardness but merely set a maximum or a minimum bound, or a bracket. Since the sizes of specimens quenched and the location of the hardness readings were not always given, it was occasionally necessary to estimate reasonable limits for them. Only the nominal compositions were available in some cases. As quenching from below the ß transus is equivalent to starting with a mixture of a and ß phases, whose individual composition would differ from the overall composition of the alloy, only measurements after quenches from above the ß transus were used. Hardness measurements on samples heated during metal-lographic mounting were also discarded. Because of their bulk, the data used will not be reproduced. They have been or will be published elsewhere.5-22 Approach All data were first translated into terms of ideal round size. For conversion from Jominy or quenched round or sheet, the author's graphs were used." For a few furnace cools or helium quenches where cooling rates were given, conversion was made on the basis of equal cooling coefficient.23 Plots of ideal round size for peak hardness against percentage of alloying element were next made for

Jan 1, 1956

By W. C. Lacy

The last crop of graduates from our colleges and universities who sought employment in the mineral industries found that they needed to hustle to find a job. There was no longer a list of waiting employers to choose from. Some of them became discouraged and drifted into other fields; many are still looking for employment. Word has gotten around that there are no jobs available in the mineral industries, and enrollment in the various colleges of mines and mineral industries has started to drop. Even established professional men are finding themselves suddenly out of work because of unstable metal prices and rising costs. All these people-students beginning to search for a career, young engineers not yet established-face the same problem: "What is the future of the mineral industries, and what type of training will best qualify the scientist or engineer for this changing field?" This question was posed to a number of leaders in different phases of the industry. Their comments are summarized as a guide to those considering a career in the finding, extraction, or beneficiation of mineral products.

Jan 1, 1960

By Mark S. Childs

FRIEDENSVILLE orebody in Lehigh County, Pennsylvania, lies in the south central part of the USGS Allentown Quadrangle. Physiographically the area is located in a small reentrant-known as Saucon Valley-of the Great Valley Province into the Reading Prong of the New England uplift. Saucon Valley itself is an oval-shaped lowland eight miles long and four miles wide, surrounded by ridges except where connected with the Great Valley through a breach in the rim known as Saucon Gap. These ridges, composed of Pre-Cambrian metamorphic rocks and Cambrian quartzites, rise some 500 ft above the valley floor. They are continuous with the New Jersey Highlands. The valley lowland is immediately underlain by lower Paleozoic dolomites and limestones. This area is one of low relief having a swing of approximately 100 ft, with an average elevation of 375 ft above sea level. The entire valley, which has a water shed of about 58 sq miles, is drained by Saucon Creek. This unit flows in a northeasterly direction to the Saucon Gap, where it discharges into the Lehigh River.

Jan 1, 1957

By Edwin Ludlow

To THE members of the American Institute of Mining and? Metallurgical Engineers who were fortunate enough to be able to attend the Fiftieth Anniversary at Wilkes-Barre, it was brought home that commercial anthracite requires not only expensive mining but that the milling or preparation of it is also a costly operation, requiring very large capital expenditures and high maintenance and labor costs. The great trouble that coal men meet in discussions of coal problems today is the difficulty the average coal user, especially in the East, finds in distinguishing between anthracite and bituminous coals. They are two entirely separate problems and yet the people who are burning coal complain bitterly of the high cost of anthracite and quote the figures furnished in regard to the prices of bituminous coal and feel that the anthracite operators are making an excessive profit, without realizing the enormous difference in the cost of production in the two fields. The great difference that can be marked is that in this year of industrial depression the prices of anthracite have been not only maintained but have increased during the summer, while the price of bituminous coal has been continually dropping since the first of the year, and yet the same law of supply and demand governs both anthracite and bituminous. In order to understand the situation the two problems must be considered from their separate points of view.

Jan 1, 1921

PUGET SOUND LOCAL SECTION. Executive Committee. CHESTER F. LEE, Chair roan. C. R. CLAGHORN, Vice-Chairman. JOSEPH DANIELS, Secretary-Treasurer, University of Washington, Seattle, Wash. W. C. BUTLER. AL K. RODGERS. On the evening of Tuesday, Sept. 2, an informal dinner was held at the University Club, Seattle, Wash., at which the Secretary of the Institute was present, and a valuable and interesting conference took place concerning the recent activities of the Institute and the relations of the Institute management to the Local Sections. SOUTHERN CALIFORNIA LOCAL SECTION. Executive Committee. THEODORE B. COMSTOCK, Chairman SEELEY W. MUDD Vice-Chairman. FREDERICK J. H. MERRILL, Secretary-Treasurer, 300 Germain Building, Los Angeles, Cal. C. COLCOCK JONES. FRANK ROBBINS. Maintains headquarters at 300 Germain Building, Los Angeles, Members of the Institute are invited to visit these headquarters whenever they are in the city. A reception was held at the headquarters of the Section on Wednesday, Sept. 10, at 8 p.m., to meet the Secretary of the Institute and discuss Institute activities and affairs. Light refreshments were served, and about 20 members of the Section attended.

Jan 10, 1913

By C. P. Lawhon, J. P. Simpson, W. M. Evans

Recent efforts to design drilling fluids for increased drifting rates have confirmed some laboratory results of other investigators, but have also produced additional data that should be considered. These data were obtained under controlled test conditions using a microbit drilling machine. Clays and some polymers have previously been reported to cause reduction in drilling rate. Recent data have shown that under laboratory conditions, suspensions of a single day or polymer have sometimes given faster drilling rates than when water was used. Measurements have been made of clay suspensions and polymer suspensions comparing filtration (I) under API conditions, (2) while drilling with temperature of 150F and differential pressure of 1,000 psi and (3) under dynamic conditions after drilling. Some correlation between instanraneous filtration (white drilling) and drilling rate has been observed. INTRODUCTION Several papers have been presented that related drilling fluids to penetration rate. Generally, it was found that a decrease in the solids concentration resulted in significant increases in the drilling rate. Of course, this change also resulted in a decrease in the viscosity of the drilling fluid.' Conclusions from investigations by this laboratory are in agreement. Data have shown that of the simple mud measurements commonly made at the drilling rig (density, plastic viscosity. yield point, API filtrate and total solids), only the density and total solids have a significant relationship to the drilling rate in Berea sandstone when attempting to correlate a single mud property individually.' More recent drilling rate experiments have been designed to study (1) effects of individual clays and polymers on drilling rates in Berea sandstone and Lueders limestone, (2) the relationship between drilling rate and dynamic filtration as measured after drilling and (3) the relationship between drilling rate and dynamic filtration as measured during drilling. Data show that drilling rates are dependent upon type and concentration of particles, type of formation and filtration of the individual fluids while drilling. Mud pressure: pressure of drilling fluid as measured after leaving the drilling chamber (Fig. 1). This is taken to be approximately the mud pressure just past the bit and at the face of the formation. Terrastatic pressure: pressure representing weight of overburden. Formation pressure: pressure of formation fluid as measured at outlet of drilling chamber (Fig. 1). This is taken to be approximately the pressure of fluid in the interstices of the formation. Differential pressure: difference between the mud pressure and formation pressure. LABORATORY EQUIPMENT AND TESTING PROCEDURE The drilling equipment was described in two previous publications."' Main components are a drilling chamber, filter-heater, rotary drive and variable-speed circulating pump. Auxiliary pumps supply pressure boosts for the mud, terrastatic and formation pressures. All equipment is designed for 15,000 psi and 500F. Capacity of the circulating system is approximately 7 gal. The mechanical design was facilitated by moving the rock down onto the bit. Data collected with this design should not differ from that obtained by a normal design where the bit moves into the rock. Drilling fluid is pumped through 50 ft of ID pipe coiled in an oil bath, enters the rotary shaft at a right angle and is pumped through the jets on the bit (Fig. 1). Most of the drilled solids are extracted by a screen mounted in the circulating system on the suction side of the pump. Data reported in this paper were obtained by controlling these parameters: mud pressure, 5,000 psi; formation pressure, 4,000 psi; terrastatic pressure, 5,000 psi; force on bit, 1,000 Ib; formation, Berea sandstone and Lueders limestone; flow rate, 7 gal/rnin; bit, 11/4-in. diameter with two 0.078-in jets; mud temperature. 150F; and rotary speed, 60 rpm. Mud pressure was controlled at 5,000 psi, thus giving a differential pressure of 1,000 psi even though the fluid densities varied. Cores of 3%;-in. diameter and 8 in. long were selected from quarry blocks to provide some control of grain size distribution, permeability and porosity. A 2-in. section was cut off each core and a I -in. diameter plug was taken from this section. Permeability to 5 percent by weight sodium chloride solution was determined and the large cores were

Prof. Henry M Howe, New York: It is extremely probable that this efflorescence of silica is due to the liquation either of silicon or of a silicide, and the subsequent oxidation of the silicon to silica. As Mr. Fackenthal says, it is very hard to see why silicon should liquate from an iron containing so little silicon, and it seems more probable that some silicide of some volatile element has liquated, and has dissociated on reaching the air, and that the volatile element has volatilized, leaving the silicon to oxidize to silica. The volatile elements present which might thus liquate in combination with the silicon are sulphur, zinc, and lead. It is hard to see why sulphide of silicon should have liquated from an iron containing so little of either sulphur or silicon. At first, one naturally thinks that either the zinc or the lead present in this furnace might have liquated as silicide. It is true that they are both volatile at the temperature within the furnace, but then the vapor-tension* of each of them within

Jan 1, 1901

By H. Hanemann

Discussion of the paper of H. HANEMANN and PAUL D. MERICA, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2371 to 2385. JOHN A. MATHEWS, Syracuse, N. Y.-I should like to ask the authors if there is any evidence of chemical change resulting information of, alpha iron from the gamma crystals found in nickel steel of high nickel content when stressed beyond the elastic limit, similar to the effect produced by drastic cooling. Would the stresses mentioned and the drastic cooling both result in an increase in magnetic induction? I would also like to ask the authors if they have made a test of the hardness. It would be very interesting to see whether the hardness decreased under the conditions of stress, as might be the case if alpha iron were produced. PAUL D. MERICA, Washington, D. C.-While it is impossible to state absolutely, it is my belief that the effect of deformation is approximately the same as, that of -drastic cooling, but we did not make a test, of the hardness.

Jan 5, 1916

By Thomas M. Drown

Theodore Dehon Rand was appointed Treasurer of the American Institute of Mining Engineers by the Council, at the Boston meeting of February, 1873, to fill a vacancy caused by the resignation of the treasurer who had been elected at the first meeting in Wilkes-Barre in May, 1871. He was elected by the Institute to this offce in the following May, and yearly thereafter until 1903. He often alluded with amusement to the abrupt way in which he was injected into this position, by my coming to his office and asking him to accept the appointment as Treasurer, on the ground that he was eminently fitted for the position by reason of his legal and business knowledge, his interest in geology and mineralogy, and more particularly because he was a neighbor of the person (to wit, myself) who was slated for the Secretaryship, and they could thus convenient.ly confer on Institute matters. He consented, on condition that the duties should not involve too.much additional work for him. This assurance was easily given, for the Institute then

Jan 1, 1904

By Doll. H. G.

THIS paper discusses a method and apparatus for determining the dip of formations traversed by a drill hole, by means of electrical measurements in the hole. The process consists in recording the Spontaneous Potentials present along three oriented generatrices in the hole, By comparison of the three curves thus obtained, after application of a correction factor to compensate for any deviations of the hole, the dip angle and the dip direction are determined. Excellent accuracy is obtained for dip angles over 10°. Because the method is simple and the apparatus rugged, the measurements are rapid and reliable; consequently, they can be made at all the levels that are of interest at any time after the well has been drilled. Mechanical cores are not needed to evaluate the dips. A convenient, time-saving procedure is to perform the dipmeter survey at the time the electrical log is taken, using for both operations the same cable and truck. Actual examples of results obtained in wells of the Gulf Coast area are given.

Jan 1, 1942

By Eugene Guccione

FOREWORD-At the SME-AIME meeting in Las Vegas this year, the SME Publications Board and the MINING ENGINEERING Committee decided that a fitting way of celebrating the United States' bicentennial would be to publish an article in ME covering the great men in American mining. After some discussion as to the inclusion of financiers -men such as William Randolph Hearst, J. Pierpont Morgan, etc.-the group agreed that the feature should be restricted to the "nuts-and-bolt people," e.g., mining engineers, geologists, mineral processing engineers. Thus, from the AIME All Institute Honors roll and from the SME Awards list, the group chose these 11 historical figures: Herbert Hoover, Daniel C. Jackling, Henry Krumb, James Douglas, Rossiter W. Raymond, Hal W. Hardinge, Seeley W. Mudd, Erskine Ramsay, Howard N. Eavenson, Robert A. Richards, Arthur F. Taggart. What follows is an account of each of these great miners' achievements and the problems they faced, and an assessment by some of today's mining leaders of the challenges that lie ahead.

Jan 7, 1976

S. F. EMMONS RESEARCH FELLOWSHIP. The movement was started by a number of the friends and admirers of the late S. F. Emmons, Economic Geologist of the United States Geological Survey, to perpetuate his name through a fellowship to be known as the ?S. F. Emmons Research Fellowship," and they have succeeded in raising some $13,000 for the purpose of carrying on research work in economic geology. The Committee in charge of this Memorial Fund has succeeded in obtaining the co-operation of Professors Kemp, of Columbia, Irving, of Yale, and Lindgren, of Massachusetts Institute of Technology, in the administration of this fellowship. These three gentlemen are respectively geologists of the institutions mentioned and are exceptionally qualified to determine in what direction the fund can be best administered. It is hoped that additional contributions will be forthcoming from many who have heard of this movement. Subscriptions are invited and may be sent to any one of these gentlemen, or to Benjamin B. Lawrence, Treasurer, No. 60 Wall Street, New York City.

Jan 10, 1913

By Joseph A. Sutton, John D. Corrick

The continuing depletion of high-grade ore de- posits in this country has created a need to develop more effective methods for recovering valuable metals from low-grade ores. The use of microorganisms for their biochemical reactions is one possible way to solve certain phases of this problem. Bacteria have been used successfully by many diversified industries. Until recently, however, little attention has been focused on the use of bacteria in mining and metallurgical processes. This report summarizes one phase of the microbial studies being conducted at the U.S. Bureau of Mines, College Park Metallurgy Research Center. The two-fold objective of this study was, first, to determine if pure strains of the bacteria Ferrobacillus ferrooxidans, Thiobacillus concretivorus and Thiobacillus ferrooxidans could utilize the iron and sulfur occurring in sulfide minerals to produce appreciable quantities of ferric sulfate and sulfuric acid for dissolving copper and, second, to develop the chemistry involved in the microbial oxidation of sulfide minerals. These are of particular interest as they relate directly to the feasibility of employing microorganisms in leaching operations.

Jan 6, 1963

APRIL BEGAN with increased disorder in the Ruhr and some blood-shed. The war cloud in the East disappeared, however, with the signifi- cance by the Turks of their intention to return to Lausanne to negotiate a treaty of peace with the Allies. The French occupation of the Ruhr continued during April without there being any spectacular develop-ments. Of course there was surliness on the part of the Germans. In the meanwhile the statesmen on both sides were intimating what they might give and what they might take, sounding the sentiment of their respective populaces. The British Government found that its revenue for the last fiscal year has been greatly in excess of expenses. The surplus was applied to reduction of the debt. A consequence of this development has been a reduction in British taxes for the ensuing year, which has naturally created a much better feeling in Great Britain. On the other hand the unemployment situation in Great Britain caused increasing alarm. At the begin-ning of April about 1,500,000 men were out of work and the thought was developing that this might be not merely a temporary emergency, but a long continuing condition. The uneasiness of the workers themselves began to be exhibited in increasing strikes and threats of strikes. There were important domestic events during April. The six miners who were on trial in Illinois for the Herrin massacre were acquitted, following which the State dropped further prosecutions on the ground that Williamson County is so thoroughly under labor domina-tion that justice could not be had there. The Supreme Court of the United States on Apr. 10 handed down a decision that an act of Congress fixing minimum wages for women in the District of Columbia was unconstitu-tional, being interference with the freedom of contract included within the guarantees of the fifth amendment. Advances of wages became more general during April. The leading event under this head was the action of the United Steel Corporation putting into effect an.11 per cent. increase in the wages of common labor on Apr. 16, by virtue of which the rate per hour was raised from 36 c. to 40 c. This was dictated by competitive conditions, the labor difficulties of the steel industry being due less to a scarcity of men than their disinclination to take jobs in that industry while the building and other industries were paying as high as 60 c. per hour for similar work.

Jan 5, 1923

By Robert S. Shoemaker

Recently we read a short article which stated that Marcona Corp. was studying the use of 25,000-hp autogenous grinding mills for an iron ore project in Alaska. As if that weren't enough, they were going to dispense with the primary crusher and feed run-of-mine ore to the grinding mills which were to be driven by wrap-around seven-cycle motors. We see also that Bougainville Copper Co. will be grinding 90,000 tpd of ore in only eight 4250- hp ball mills. At Bougainville too, their float section will be the first large one to be completely equipped with the new 350-cu ft flotation cells. After a half century of relatively peaceful growth in the minerals industry, we are now seeing almost exponential advances in both equipment and plant size. At the same time, we are seeing a constant blending of hydro and pyrometallurgical techniques and processes into minerals beneficiation until the sample grind-'em-up-and-concentrate-'em plant is becoming a rarity.

Jan 1, 1970

By N. Christensen, B. Augland, T. H. Johansen

Samples of an Fe-Nb alloy were brought to equilibriurtr with hydrogen-methane mixtures in the temperature range from 950° to 1050°C, and subsequently analyzed on their carbon contents. The solubility pvoduct L = [%Nb] [%C] may be represented by the equation Approximate solubilities indirectly assessed through hardness measurements have been included from a previous report. These data are shown to be in a fair agreement with the present solubility measurements. IN an investigation based on hardness measurements by de Kazinczy, Ms, and pachleitnerl the molal heat of solution of NbC was estimated to 11.5 kcal per mole. This value was considered rather small, and an investigation using a similar technique was carried out. The results indicated a heat of solution about 35 kcal per mole.2 At this stage it was decided to determine the solubility under conditions of true equilibrium . During the course of this work a similar investigation was published by Smith. 3 His heat of solution, 41.6 kcal per mole, is not very different from the value resulting from the present work (42.5 kcal per mole). Our solubility product, on the other hand, is at considerable variance with that reported by Smith. Possible reasons for these differences are discussed below. Mori, Tokizane, and saheki 7 have studied the behavior of niobium in commercial steels, with special attention to the formation of niobium carbide, nitride, and sulfide. Assuming a carbide composition Nbco.87 based on X-ray diffraction and chemical analysis of residues extracted from Fe-Nb-C-S alloys, the molal heat of solution of niobium carbide was estimated to 35.2 kcal per mole. MATERIALS AND EQUIPMENT The chemical analysis of the materials is given in Table I. Electrolytic iron* was used in the preparation of

Jan 1, 1968

A development drilling and bulk sampling program should furnish the following information: (1) geology of the mineralized zone, (2) quantitative data on grade and tons of material within pertinent cutoff limits, (3) physical size and shape of the deposit and areas underlain by waste as well as ore, (4) mineralogical and metallurgical characteristics of the ore, (5) physical characteristics of the ore, (6) bulk samples for metallurgical testing and grade, (7) data on factors that affect mining operations, such as ground water and ground conditions. The method and equipment best suited for a particular drilling job depend upon the geologic features of the mineral deposit to be tested.

Jan 10, 1967

By R. F. Domagala

SOME of the results of a program designed to study the kinetics of transformation and related mechanical properties of prototype Zr-X binary alloys systematically are presented here. The object of this program was to provide a sound basis for a scientific approach to the realization of optimum properties in binary zirconium alloys. Alloys of Zr-Mo (eutectoid), Zr-Sn (peritectoid), and Zr-Ti (a and ß isomorphous) were prepared and studied. The data herein are confined to a presentation of the results of studying the eutectoid prototype alloys. The Zr-Mo phase diagram has been determined.&apos; A definitive metallographic study of isothermaily annealed samples prepared from high purity elements served to position a sluggish eutectoid reaction, ß?a + ZrMo2, at 780°C. The compositions of the phases involved in this reaction are: ß, 7.5 ±1 pct Mo; a, <0.18 pct Mo; and ZrMo2, 67.8 pct Mo. Inasmuch as a lower purity sponge zirconium was used in this work boundary placements were rein-vestigated with the less pure alloys. Materials and Procedures Hafnium-free sponge zirconium was used to prepare all ingots. The arc melted hardness of a small button of this zirconium was found to be Vpn 168. Chemical analyses conducted at Armour Research Foucdation are shown in Table I, High purity molybdenum sheet was used as the alloy addition. A typical analysis is shown in Table I. Several 200-g Zr-50 pct Mo alloys were made by arc melting. Crushed granules of this material were used to ensure inqot homogeneity Ailoy ingots were prepared by double melting techniques. First, three 5-lb ingots of each alloy composition were are melted in 2 nonconsumable electrode arc furnace. After melting. the ingots were ground to remove surface defects. A subse-

Jan 1, 1958