Search Documents

By M. K. Yen

The distortion of crystal structures referred to as "biege gleitung",1 "local curvature"2-4 and "deformation bands"5,6 is believed to be an unavoidable characteristic of deformed single crystals. The presence of asterism on Laue photograms of Al single crystals either deformed by pure shear7 or extended in a condition relatively free from the grip effect2 indicates strong evidence substantiating this point of view. The type of localized bending described in connection with the bending test of Al single crystals by Yen and Hibbard8 could conceivably exist either microscopically or submicroscopically in all types of deformation. The purpose of this note is to extend this idea to the postulate of a hypothetical "microbending site," as applied to the mechanism of slip in a general sense. The mosiac structure, as postulated by Darwin,9 is that crystals were actually composed of small blocks which have a linear dimension 10—4to 10-6 cm on the edge and deviate from each other by an angle of about one-tenth of a degree. The following discussion is based on the assumption that when slip is propagated from one mosaic block to the adjacent one, bending of the lattice at the region of their boundary is produced in order to maintain the continuity of the gliding process along a certain slip plane. Consider a two-dimensional diagram of two ideal mosiac blocks on the cross-section perpendicular to the slip plane and containing the active direction of slip. When an external force is applied, the localized bending or "microbending site," would be generated at the region as illustrated in Fig 1A at point B. A schematic diagram of a "microbending site," generated at a mosaic boundary, is illustrated in Fig IB. It may be seen that once the curvature of the bending site reaches sufficient magnitude, the interaction force encountered by pairs of atoms symmetrical with respect to the center of the bending is equal but opposite in sign. Consequently, the overall energy required to displace the atoms near the center is approximately zero.10"12 Based upon the finding that the misalignment between two mosaics is 0.1 degree,9 the assumption is made that "microbending sites" may possibly exist in the region where one plane will have one more row of atoms than an adjacent plane. It is probable that the origin of the bending site will be where the distance between two mosaic boundaries is "2d" as shown in Fig 1A at point B, where " d" is the interatomic distance. Thus, the distance between two "microbending sites" is in the range of about 600 interplanar spacings. In the case of aluminum, the spacing between two octahedral planes is about 2.33 A. The distance between two bending sites will be approximately 2.5 X 10"5 cm. It is interesting to note that according to Woods13 these values approach closely the size of the domains of a cold-worked metal whose minimum

Jan 1, 1950

By James Aston

INDICATIVE of the practical importance of the achievement of James Aston , recipient of the Robert W. Hunt Medal for 1930, is the following prosaic item from the financial columns of a recent issue of a New York newspaper. "According to private advices from Pittsburgh, production costs of the A. M. Byers Co. for 1929 were reduced about $5 a ton by the use of the Aston process for making wrought iron pipe. A greater saving is anticipated for 1930, when more of the company?s requirements will be produced by the new method."

Jan 1, 1930

[ ] (17) WORTHINGTON: Cartoonist-author Don Herold recently took a look at the Worthington Corp., putting the results into a compact booklet called "A lot of things beside pumps." The story is aimed to better acquaint you with Worthington and how they came to produce a diversified industrial equipment. (18) SPEED REDUCERS: Now available is Cleveland Worm & Gear Co.'s new general catalog. In its 180 pages are the illustrations and description of the complete Cleveland line, together with full engineering data, dimensions, weights and horsepower capacities of the various drives. (19) METAL PRODUCTS: Armco Drainage and Metal Products, Inc. has just published a condensed 6-page catalog of its products designed for mining use. It describes and illustrates such products as Flex-Beam guardrails, corrugated metal pipe, liner plates, retaining walls, Steelox buildings, and welded pipe. (20) RECORDS: Pre-scheduled, controlled, preventive maintenance reduces costly downtime to a minimum and eliminates the need for large emergency crews. A new folder describes how such a program can be accomplished by using Remington Rand Inc., Kardex visible records. Another Remington Rand Inc. bulletin is the certified case history of how Kardex visible purchasing records help maintain a smooth running purchasing department.

Jan 1, 1952

By T. S. Lundy, R. E. Pawel, F. R. Winslow, C. J. McHargue

The volume-diffusion coefficients of Nb-95 and Ta-182 in niobium have been measured over the temperature range 878° to 2400°C. High-temperature specimens (T 21500°C) were sectioned by conventional lathe and grinding techniques while low-temperature specimens were sectioned by an anodizing and stripping technique previously described. Over a range of more than ten orders of magnitude in diffusivity, the self-diffusion data is well-represented by the equation: D = (1.1+ 0.2) exp [- (96,000 * 900)/RT ] cm2/sec Upward deviations from this line are explained by short-circuit diffusion in combination with the loss of resolution of the sectioning techniques. Oxygen contamination within the range 100 to 450 ppm was found to have little or no effect on the self-diffusivitj 01 niobium. In a limited number of measurements, the diffusivity of Ta-182 in niobium was found to be about half that of Nb-95 in niobium. These data may be described by D = (I.0+0.90.5)exp [- (99,300 * 2400) /RT ] PREVIOUSLY reported studies of self-diffusion in niobium were by Resnick and Castleman1 and Peart, Graham, and Tomlin.2 The data of Resnick and Castleman over a temperature range 1585" to 2120°C show considerable scatter but. can be represented by D = (12.4 *0.8) exp [-(105,000+3OOO)/RT] cm2/sec The limited data of Peart, Graham, and Tomlin follow the equation D = 1.3 exp (-95,00O/RT) cm2/sec In view of recent diffusion data for ß zirconium3 and 0 titanium4 in which Arrhenius-type plots do not yield straight lines and of the potential high- temperature uses of niobium and its alloys, we thought it important to investigate the diffusion behavior of this bcc refractory metal over a large temperature range. This has recently been done for molybdenum,5 chromium,6 vanadium,"" and tantalum.9 Niobium was a particularly suitable material for this study largely because of the development of an anodizing and stripping sectioning technique which enables diffusivities as small as l0-19' sq cm per sec to be determined accurately.10 In addition to self-diffusion data, data were obtained for the diffusion of Ta-182 in niobium and for the effect of varying oxygen content on self-diffusion. I) EXPERIMENTAL PROCEDURE Materials. The niobium was obtained from three sources: 1) melting stock from Shieldalloy Corp., 2) electron-beam melted single crystals, 1/2 in. diameter, from Semi-Elements, Inc., and 3) oxygen-doped, electron-beam melted single crystals from Materials Research Corp. The melting stock was electron-beam melted and specimens 5/8 in. diameter by 1/2 in. long were machined from the center of the bar. The analysis supplied by the vendor and an interstitial analysis of one of the specimens are given in Table I. The single crystals (type 2 above) were cut with a jeweler's saw to specimens about 3/8 in. long. The interstitial analysis of this material is given in Table 11. This material was used

Jan 1, 1965

By John A. S. Dow, Garry G. Lowder

Tapadaa is one of several centers of porphyry copper mineralization in northern Sulawesi. Host rocks are mainly varieties of quartz diorite porphyry. Structural control of mineralization is indicated by elongation of the sulfide system (5 x 1 km) parallel to prominent NW-trending structures, but in detail mineralization is strongly influenced by relative age and lithology. Hydrothermal alteration is characterized by widespread occurrence of advanced argillic assemblages and the presence of sodic rather than potassic alkali feldspar. Propylitic alteration surrounds the mineralized area. Phyllic and advanced argillic alteration occur in structurally controlled zones and in limited pervasive areas. Hypogene copper mineralization develops in rocks with sericite-albite alteration and comprises low total sulfide chalcopyrite-bornite or chalcopyrite-pyrite.

Jan 1, 1978

By W. L. Staker

The Bureau of Mines investigated selective extraction of Au and Ag from a low-grade Au ore containing Hg. Gold and silver were extracted from the ore in cyanide slurries, and Hg extraction was suppressed with sodium or calcium sulfide. Maximum Au extraction and minimum Hg extraction were obtained using solutions containing 0.34 lb NaCN/ton of solution. Increasing the cyanide concentration increased Hg extraction without increasing Au extraction. Mercury extraction from the ore was suppressed with 0.5 to 2.9 lb CaS/lb Hg in the ore. Gold-to-mercury ratios of 100:l to 400:l were obtained in the leach solution, and on the activated carbon in a CIP circuit.

Jan 1, 1984

Sept. 3-6, AIMS, Fall Meeting, Industrial Minerals, Minerals Beneficiation, Mining, Geology, & Geophysics, Iron and Steel, and Coal Div., Palmer House, Chicago. Sept. 3-13, AIMS, Chicago Section, Centennial of Engineering, Chicago. Sept. 5-6, Engineers' Connell for Professional Development, annual meeting, Hotel Sheraton, Chicago. Sept. 8-15, International Geologic Congress, Algiers. Sept. 11-13, American Institute of Chemical Engineers, Palmer House, Chicago, Ill. Sept. 18, RIME, Utah Section, Newhouse Hotel, Salt Lake City. Sept. 22-25, American Mining Congress, Metal and Nonmetallic Mining Convention and Exposition, public auditorium, Denver. Sept. 23-25, Institution of Mining and Metallurgy, symposium on mineral dressing, Royal School of Mines, London. Sept. 30, AIME, Morenci Sub-section, Longfellow Inn, Morenci, Ariz.

Jan 1, 1952

By R. A. Wyman

KYANITE schists in the Sudbury area have been generally described by Haw,1 who has also given particular information on preliminary treatment of three large samples from Dryden township, Ontario.2 Kyanite, garnet, biotite, quartz, and feldspar comprise the main ingredients of this ore. Kyanite is the valuable mineral. About 5 ½ tons of -35 +200 mesh product, made by dry rod milling, screening, and separation on the Exolon magnetic separator, were available for treatment by flotation. Magnetic separation had effectively reduced garnet and biotite so that flotation feed consisted essentially of kyanite, quartz, and feldspar, the kyanite content averaging 32 pct and representing about 86 pct of the kyanite in the original ore.

Jan 1, 1958

By F. A. Emmerton

I have used for about two years, in the laboratory of the Joliet Steel Company, a rapid method for the determination of phosphorus in iron, steel, and ores, which possesses one or two features sufficiently novel to warrant description. In general, it is the method described by Mr. Benjamin B. Wright (Transactions, vol. x., p. 197), involving the precipitation of the phosphorus by means of molybdate solution, and its estimation in the yellow precipitate by reduction of the molybdic acid, and titration of the resulting oxide with a standardized permanganate solution, according to the principles laid down by Werncke (Fres, Zeit., vol. xiv., p. 1). In the use of this method, I had difficulty at first in obtaining a yellow precipitate of reasonably uniform composition. It is a well-known fact that, to secure this result, the conditions of precipitation must not vary. The principal condition is temperature; and acidity, concentration, proportion of nitrates and chlorides, and time, are important elements. I am aware that uniformity in these conditions has been obtained to a reasonable extent by many chemists,. so that they are enabled to use with success, methods based on the

Jan 1, 1887

By R. C. Rastogi, F. F. Aplan

The goal of this study is to evaluate the coal flotation process and the interaction of the chemical (reagent) and hydrodynamic (machine, operational) variables as they affect yield, flotation of various sized particles, and sulfur and ash rejection. Coal flotation is found to follow a first order process with the coal floating much faster than either pyrite or ash. This circumstance may be used to achieve gangue rejection during flotation. When floated with MZBC, cresol, or pine oil frothers, coal floats in the size sequence: 108 pm ( - 65 mesh), 589 x 808 pm (88 x 65 mesh), and 1.17 mm x: 589 pm (14 x 18 mesh). However with a substantial amount of fuel oil collector, all particles tend to float roughly in proportion to their content in the feed. An increasing aeration rate was found to be the most important variable in increasing the coal flotation rate. This increase in flotation rate, unfortunately, is also accompanied by an increase in the flotation rate of the pyrite. The rejection of pyrite during coal flotation is best accomplished at low aeration rates, low frother concentrations, and low impeller speeds.

Jan 1, 1986

By Charles Hart

THE art of electric smelting came with the turn of the present century and owes its existence to the introduction of alter-nating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N, Y. Prior to that time current was largely direct. The fur-naces were electrolytic in nature and found their first metallurgical use in the produc-tion of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific publications and books written during the first two decades of this century.

Jan 1, 1940

By H. R. Green, D. M. Lamb, A. D. Taylor

The design of slurry launders has usually been based on strictly empirical concepts. An examination of the most common procedures reveals that they do not account for many of the variables that are recognized as significant for slurry transport. These may include flow rate, volume concentration of solids, solids specific gravity, solids size distribution, particle shape, launder geometry, and roughness of the wetted surface. It was decided to develop a design procedure, which would accomplish two things: First: Take into consideration most of the known significant variables and systematize the procedure to assure consistent results. Second: Provide a rational basis for examining and utilizing operating data to refine and improve the system. To accomplish this, it was necessary to develop a basic design concept. This concept has been developed through a complex development history, and yet still appears workable and technically sound. That concept may be outlined as follows: First: The solids transport velocity is the fundamental basis for slurry launder design. Second: The stream configuration, hence the launder size, is integrated with the solids transport velocity so that the actual stream velocity exceeds the solids transport velocity. Third: The launder slope is that which will achieve the

Jan 1, 1979

By James E. Hoffmann

This paper reviews the chemistry of selenium and its compounds as it applies to the recovery of selenium from electrolytic copper refinery slimes. Based on this chemistry various processes for the extraction and recovery of selenium from refinery slimes are explained and developed. The optimum selenium technology processes is dependent upon many factors including copper refinery location, environmental and regulatory conditions, local markets for selenium or selenium chemicals, and other plant processes. For this reason there is no one best process but rather a variety of useful processes for winning selenium. Those which have demonstrated consistent utility in both ease of recovery and reliability are discussed in more detail. Recovery of selenium by Doré furnacing of slimes is the topic of a separate paper. The companies that have developed selenium extraction technology are not being cited in this paper for the following reasons: o Their current technology may be different o The actual inventor of a process is difficult to credit since many different organizations have pursued parallel inquiries in developing better processes. Finally, some selenium extraction processes have been omitted; not because they are unworthy of consideration but rather due to limitations of space.

Jan 1, 1984

By Jules E. Jenkins

IN the past quarter century the seismograph has played an increasingly important role in evaluating vibratory effects transmitted to adjacent communities by industrial blasting operations. In this period research has advanced through two major phases—from falling pin seismometers to three-component recording seismographs. The initial phase of this research is now regarded as the era of recording, during which the seismograph merely recorded occasional events. It has emerged from this stage into the era of control and analysis and in this later period has been recognized as a full-fledged industrial tool. Although the falling pin machines of earlier years indicated probable amplitudes of industrial blasting vibrations, they gave no reliable measure of such displacements, nor did they provide essential information concerning direction or frequency of motion. The first contribution of the three-component recording seismograph was the weight-for-distance formula developed by the U. S. Bureau of Mines. This empirical formula enabled users of commercial explosives to determine beforehand the probable vibratory effects of a blast when the weight of the explosives charge and the distance from the shot point were known. This formula has withstood the test of time and is still applicable for blasts detonated by instantaneous methods. The second major contribution of the three-component recording seismograph followed the introduction in 1945 of short period or millisecond delay detonation. This might be described as a two-stage contribution, the first of which revealed a 50 pct reduction in the vibration magnitude when millisecond detonation was used rather than instantaneous discharge. This second part of this double contribution led to the discovery of the vibration dip phenomena, see Fig. 1. In Fig. 1 the horizontal coordinates indicate the displacements amplitude in inches, and the vertical coordinates, the explosive weight in pounds. The top curve is that of the U. S. Bureau of Mines for instantaneous detonation. Its curvature conforms to the two-thirds power of the explosive weight as provided in the weight-for-distance formula; hence the vibratory effects increase in proportion to an increase in the explosive charge. If the other curves shown below are temporarily disregarded, it may be considered that the entire area below this top curve represents both useful and waste energy. As mentioned previously, when millisecond delay detonation was first investigated it was found that in general the U. S. Bureau of Mines curve could be decreased by about 50 pct, or to the position of the middle curve. At the outset it was assumed that this curve would likewise increase in some proportion to the explosive charge, as did the top curve, that is, the curve would indicate a continuous upswing. As seismographic data accumulated this assumption was found to be erroneous in part. It was discovered that

Jan 1, 1957

By Willard P. Ward

IT is the object of the present paper to bring to the notice of members of this Institute, the results of experiments made during the past six months in the manufacture of the alloys of iron and manganese in the blast-furnace. The ores at hand and available for the purpose were brown hematites, containing but a very small percentage of manganese, and various manganese ores containing a small percentage of iron. It is hardly necessary here to call attention to the statements regarding the production of iron-manganese alloys from such ores, which are given by all the well-recognized authorities on metallurgy. Suffice it to say, in a few words, that they hold that the operation is practically impossible, and that in the use of oxides of iron and manganese, mechanically intermixed in the same ore, much difficulty has been found in producing spiegeleisen. Spathic ores, containing manganese chemically combined, are alone recommended for the production of spiegel, and even then it is said that well-managed furnaces produce only about 75 to 80 per cent. of spiegel, the balance of the production being white laminated pig or gray iron.

Jan 1, 1876

By Willard P. Ward

It is the object of the present paper to bring to the notice of members of this Institute, the results of experiments made during the past six months in the manufacture of the alloys of iron and manganese in the blast-furnace. The ores at hand and available for the purpose were brown hematites, containing but a very small percentage of manganese, and various manganese ores containing a small percentage of iron. It is hardly necessary here to call attention to the statements regarding the production of iron-manganese alloys from such ores, which are given by all the well-recognized authorities on metallurgy. Suffice it to say, in a few words, that they hold that the operation is practically impossible, and that in the use of oxides of iron and manganese, mechanically intermixed in the same ore, much difficulty has been found in producing spiegeleisen. Spathic ores, containing manganese chemically combined, are alone recommended for the production of spiegel, and even then it is said that well-managed furnaces produce only about 75 to 80 per cent. of spiegel, the balance of the production being white laminated pig or gray iron.

By Regis Chauvenet

I have been requested to sketch the iron resources of the State of Colorado, with reference both to existing, i.e., working mines, and to prospects more or less developed, but not contributing anything as yet to actual shipments. I should mention, though disliking apologies, that there is one region of the State which I believe to be important, and which has been assigned to me (with reference to its iron-deposits particularly) in the field-work of the present year for the School of Mines, which has not been systematically explored, and whose data are not in such shape as to enable me to give them in this paper. The region in question is Pitkin county and part of the adjoining country. Regarding the geological positions of the veins or deposits, they are sufficiently varied. In Boulder county there is a well-defined vein of titaniferous magnetite in ancient granite or gneiss, while in Park county there may be seen a deposit now under construction, as will later be described; when finished it will belong, let us say, to the post-quaternary. Between these, in Cambrian, Silurian, and Lower Carboniferous formations, are various deposits, and even the

Jan 1, 1890

By J. T. Shapland

When externally mounted sliding-gate valves are used to control the flow of metal from ladles, none of the valve components are immersed in steel. In general, the refractories used to date in sliding-gate valves have been made of a high-alumina composition. Because these refractories replace the fireclay sleeves and clay-graphite heads used to construct conventional stopper rods, they represent a major change in the use of pouring-pit refractories, Changes in the well and lining of the ladle as a result of conversion to external flow control probably will not be as severe; however, the sliding-gate valve makes it possible to preheat to a higher temperature and to decrease the turnaround time, and materials more refractory than those currently employed, such as basic brick, might be used in these areas. Another area of pouring-pit refractories that has became quite important is the tundish used with continuous casters. The use of external flow-control devices on tundishes makes it possible to use the tundish for prolonged periods of time and makes the use of better refractories necessary. In this application, high-alumina and zirconia are finding acceptance.

Jan 1, 1972

Jan 1, 1927

By Philip D. Wilson

OF all the metals in the war program the demand for and the production of magnesium have increased percentagewise the most. In the prewar year 1939 the production was 3350 tons. The war program, twice expanded, now provides for nearly one hundred times that amount annually. The goal announced by the War Production Board in February 1942 was 362,500 tons per year. Be- cause of the development during the year of satisfactory types of incendiary bombs other than magnesium this objective has been somewhat reduced but the capacity of the plants already built or under construction will be huge. The Aluminum and Magnesium Division of the W.P.B. has had the responsibility of planning and implementing this expansion and of providing fabricating facilities as well for this greatly increased tonnage of magnesium ingot.

Jan 1, 1943