Search Documents

By Gordon H. Geiger, J. Bruce Wagner

Electrical conductavity and therrnoelectvic nzeasuretnents on synthetic hematite slabs with 0.01 to 0.90 at. pet Ti and with 0.30 at. pet Ca were made. Additions of titanium and of calcium both increased the electronic conductivity with titanium yielding greater n-type behavior and calciurn p-type behavior. Reduction studies of hematite to magnetite in CO-CO2 atmospheres between 600° and 900°C initially exhibited linear kinetics. These linear rates were increased by additions of titanium and decreased by calcium. IN recent years many studies have been reported in the literature on the kinetics of the reduction of hematite and magnetite to iron. In addition, Hansen and Josephl and Schenck and Schultz2 have reported studies on the reduction of hematite to magnetite, the first step in total reduction to iron. In order to evaluate the results of the studies of over-all reduction in terms of the actual mechanism of the reaction and to define further the important factors in the rate- controlling mechanism of the magnetic roasting reaction, the following experiments were undertaken. Specimens of undoped hematite and hematite containing titanium or calcium in solution as doping agents were reduced to magnetite in CO-CO2 mixtures. In addition, electrical-conductivity measurements were correlated with the reduction kinetics using concepts of defect solid-state chemistry. EXPERIMENTAL Fisher certified Fe2O3 powder was used to make specimens for both the electrical and kinetic studies (see Table I for analysis). Doping with titanium and calcium was accomplished by adding TiO2 and CaO powders to the Fe2O3 powder. The powders were mixed in a Waring blender for minimum times of 1/2 hr. Satisfactory blending was achieved based on comparison of analyses of individual specimens af- ter reduction. The specimens were formed in a steel die using opposed punches with a rectangular opening 10.0 by 40.0 mm. The Fe2O3-TiO, platelets were pressed cold at 16,000 psi. They were sintered for approximately 16 hr at 1075°C in air, in accordance with information in the literature3, 4 on the time and temperature needed to obtain solution of the titanium in the hematite. The Fe2O3-CaO mixtures were first cold-pressed at 20,000 psi and sintered for 3 hr at 1225°C to insure solution of CaO. This material was then ground to -325 mesh in a 6-in. ball mill and the resulting powder was used to make platelets in the same manner as above. The sintered platelets were usually between 1/16 and 1/8 in. thick. They were ground on a carborundum wheel and polished on 2/0 paper. Typical dimensions of the kinetic-study specimens were 1.6 by 0.8 by 0.05 cm, and a typical weight was 0.3 g. Conductivity and thermoelectric specimens were approximately the same size, but were subjected to further sintering in order to ensure maximum densification. Finally, all specimens were measured to the nearest 0.0005 in. and weighed on a Mettler H-15 balance to the nearest 0.0001 g and the density calculated. The average density of the specimens used for the reduction studies was 4.87 g per cc, or 7.1 pet total porosity. The standard deviation ranged from 0.14 to 0.063 g per cc within a composition group. In the present study, the apparent surface area as measured with a micrometer was taken as the true surface area. The chemical analyses for calcium and for titanium within a group showed maximum variations of 50.04 pet from the average values used in Figs. 9 and 11. In order to suspend the specimen from the balance for the kinetic studies, a hole, 0.03 in. in

Jan 1, 1965

By J. M. Uys, T. B. King

The solubility of water in silicate melts of various compositions was measured. The basicity of the silicate did not appreciably affect the water solu-bulity at low-base content (acid compositions). Near the orthosilicate composition the solubility increased with basicity for silicates in which the cation displayed a weak ion-oxygen attraction and apparently decreased for those in which the cation showed a strong ion-oxygen attraction; metasilicates of the former class dissolved more water than those of the latter. Temperature had little effect on water solubility. The experimental results are interpreted on the basis of two modes of solution, the contribution of one decreasing, and that of the other increas -ing, with increased melt basicity. In the former, solution occurs through interaction with doubly-bonded oxygen atoms and in the latter, through interaction with singly-bonded oxygen atoms, or, in very basic melts, through reaction with free oxygen ions. THE hydrogen content of a steel melt is in a large measure determined by water dissolved in the slag. In some glasses water may be a major cause of "seeds". Water vapor in the furnace atmosphere is the primary source in both instances. A knowledge of the mechanism of water solution in silicate melts should help in assessment of practical methods for its control in steelmaking and glass refining. Walsh et a1.l measured the water content, expressed as hydrogen, of 40 pct lime-20 pct alumina-40 pct silica and 62 pct manganese oxide-38 pct silica melts as a function of the steam partial pressure, in equilibrium with the melt. Tomlinson 2 and, also, Russell3 investigated this relationship for a molten 30 pct soda-70 pct silica glass. In all three investigations, the solubility of water was found to be proportional to the square root of the partial pressure of steam. Moulson and Roberts 4 confirmed this relationship for a silica glass. On the basis of the square root relationship, Tomlinson2 and Russell3 interpreted the solution reaction as "network-breaking", similar to that expected on the addition of metal oxides to silica. Walsh et al.' postulated two possible modes of solution, one the mechanism suggested by Tomlinson and Russell and the other the reaction of the water molecule with an oxygen ion to form hydroxyl ions. These two modes of solution suggest opposite effects of melt basicity on water solubility. However, little appears to be known about the effect of melt basicity on water solubility. Walsh et a1.l found, in the lime-silica system, that the water content increased slightly with increased basicity. As these authors pointed out, this does not appear to be in accord with their further observation that slags containing little or no silica dissolve very little water. Kurkjian and Russell5 measured the effect of basicity on water solubility in alkali silicates in the composition range 15 to 45 mole pct alkali oxide. They found a minimum in the water content at about 25 mole pct alkali. This was interpreted on the basis of two concurrent solution reacZions; one in which solubility was proportional to the activity of doubly-bonded oxygen and, in the other, proportional to the activity of singly-bonded oxygen. The present work was aimed at establishing the effect of basicity on water solubility in silicate melts over as wide a range of compositions as practical. APPARATUS AND EXPERIMENTAL PROCEDURE The silicate melt was equilibrated with a "carrier-gas" of accurately known water content, quenched, and analyzed for water by a vacuum fusion technique. Some pertinent details of the equilibration procedure, analysis technique, preparation, and handling of the silicates are given below. Gas-Silicate Equilibration. The apparatus used to equilibrate the melt with the gas mixture was similar to that used by Walsh et al.' but with some important modifications.6 Purification trains were provided for nitrogen and hydrogen; whenever air or oxygen was used as carrier gas the nitrogen purifiCation train was used with the copper furnace at room temperature. Gas flow rates were measured with capillary flow meters; bleeders filled with a mixture of dibromo and tribromo ethyl benzene (density about 2 g per cc) were used for convenience in controlling flow rates.

Jan 1, 1963

By AIME AIME

IN times of stress nations pick strong men to lead them. Similarly the Coal Division selected forceful Larry A. Shipman, fuel engineer for the Southern Coal and Coke Co., Knoxville, Tenn.. to lead it through the year 1945. He was born in Indianapolis May 13, 1891. Following graduation from a technical high school in that city Larry began his fuel career approximately 35 years ago attached to one end of a scoop shovel, firing locomotives for the Pennsylvania Railroad. At the end of two years he transferred to the New York Central Lines and held these jobs successively: locomotive fireman, engineer, fireman instructor, supervisor of instructors, and fuel engineer.

Jan 1, 1945

By JOHN R. SUMAN

I WOULD like to spend a few minutes describing to you the present condition which exists in the oil industry and then point out some aspects of this deplorable situation in which I think petroleum engineers can be helpful. As you know, the oil business at this time is in a very critical condition, .due to the tremendous potential production in excess of current demand. This is a world-wide condition as well as a national problem, as it is estimated that the surplus production available for the market in foreign countries is of about the same proportion as that existing in the United States. Due to the inability within the United States to hold production within the bounds of demand prices have been slumping for the last four years and at this time have reached the point where the sales value of the average barrel of crude oil in the United States, is far below the cost, of production. In addition to the large amount of potential production available for the market in excess of demand we have in storage in the United States about six hundred fifty millions of barrels 'of oil. Unless something can be done to limit the amount of oil coming onto the market to a point well below the demand, which point will permit the reduction of stocks, it looks as though the 'oil business is facing demoralization.

Jan 1, 1931

By Joseph Lindmayer, Karl M. Busen

If silicon is in contact with silicon oxide, a heterojunction is formed which induces an inversion layer ("channel"). Influences of impurities and structural parameters on the channel are discussed. There seems to be no relation between surface damage in silicon and the channel. Phosphorz~s doping of the silicon oxide has no pronounced effect on the channel. Channels which were well above the range predicted by the heterojunction model were related to the action of H* at the silicon/silicon oxide interface. Channels which were well below tlze range predicted by the heterojunc-tion model were related to a transition region in the oxide adjacent to the interface. In support of the assumed transition region and the H+ are the ex-periments described on the paper. Furthermore, the concept of metastable OH groups in silzca, known from other publications, has been used to explain certain channel characteristics by the formation and the accommodation of hydrogen in the silicon oxide. THE electrical characteristics of a semiconductor device in many cases are influenced by the conditions of its surface. Because these conditions often are changing with temperature, time, ambient, or other parameters, numerous attempts have been undertaken to stabilize them by suitable processes. Several years ago Atallal studied the silicon/silicon dioxide interface and since then increasing attention has been given to the silicon dioxide as a means to stabilize silicon surfaces. This led to the evolution of the planar silicon devices where oxide layers are used to protect places at which the junctions are intersecting the surface. The formation of the oxide layers on silicon can be carried out by a variety of processes: high-temperature thermal oxidation (exposing the silicon surface to oxidizing agents such as 02, HzO, COz), evaporation of SiOz, or anodic oxidation of silicon. Originally the oxides were considered able to "passivate" the silicon surface and it was understood that they 1) protected the surface against any influence from the ambient and 2) stabilized surface conditions which were necessary for proper device performance. It soon was realized that the second quality was not always obtainable: Atalla and Tannenbaum showed that, in the process of forming a layer on doped silicon by thermal oxida- tion, electrically active impurities in the silicon near the interface are redistributed, thus giving rise eventually to the formation of unwanted charge distributions. The degradation of planar junctions during reoxidation of silicon was observed by Barson et a. Surface studies with silicon planar junction structures indicated that the breakdown voltage depended on the kind of procedure which was applied during or after oxidation.*" Yamin and worthinge report on charge storage and dielectric properties of SiOz films at elevated temperatures. Another influential parameter on the silicon surface is discussed by Lindmayer and usen,' namely the appearance of a surface potential on silicon as a consequence of the heterojunction formed by the silicon/silicon oxide interface. In the present paper the influence of impurities and structural parameters in silicon oxide in connection with the heterojunction is a particular object of our investigations. I) EXPERIMENTAL The material used was 10 ohm-cm p-type silicon slices with either damaged surfaces (mechanically lapped or polished) or damage-free surfaces (chemically polished). The majority of the slices were oxidized for 1 hr and 20 min at 1250°C in a steam + oxygen atmosphere generated by passing O2 through HzO at 90°C (wet oxygen). This led to oxide layers of about 9000 A. On some slices oxide layers were grown in pure oxygen (dry oxygen). By a photoresist process a set of 20 by 200 mil windows was then etched out from the oxide layer. The pattern of the windows is shown in Fig. 1. In a subsequent process n-type pockets with surface concentrations between 2 x 10" and 5 x 10" cm"3 were formed by phosphorus diffusion. This allowed ohmic contacts between the silicon surface and tungsten probes which for electrical measurements were placed into two adjoining windows and

Jan 1, 1965

By J. W. Lacey, F. H. Brinkman, J. E. Faris

This paper presents an analysis of the high-pressure, gas-driven LPG-slug process, based on fluid flow tests in areal models. Two types of tests were made. One series was made in low-pressure models which permitted observation of fluid movement. Three completely misci-ble analog fluids were used. A second series of tests was made in high-pressure models using methane, propane and a light refined oil saturated with methane at room temperature and 1,550 psig. Under the test conditions of room temperature and a pressure level of 1,550 psig, the phase diagram for the fluids used is similar to those for many of the field systems where the process is considered for use. A method for using these laboratory data to calculate field performance of the process is outlined. As a result of this work, it is concluded that small banks of LPG (5 per cent HV or less) are not effective in increasing oil recovery in horizontal reservoirs. Znstead, where small banks are used, the driving gas quickly penetrates the LPG bank because of fingering and channeling; and from this point on, the process behaves essentially as an immiscible gas-injection project. The validity of this conclusion was substantiated by: (1) laboratory studies of the effect of rate, model size and mobility ratio on miscible displacement in areal models; and (2) calculation of field recovery, which compared closely with actual field recovery. INTRODUCTION Field applications and pilot tests of the gas-driven, LPG-bank, oil-recovery process are on the increase. Most of these tests are employing small banks (2% to 5 per cent hydrocarbon volume) of LPG, which is miscible with both the driving gas and the oil in place, in an effort to attain an effective yet economical miscible displacement of oil by gas. The expectation of miscible displacement with small banks is based on the concepts that: (1) lengths of solvent-oil mixed zones, measured during miscible displacements in long slim cores, are representative of those that will occur in the field; and (2) areal sweep efficiencies5 measured in electrolytic model studies are applicable to miscible displacement in reservoirs. Our experimental evidence indicates that the mixed-zone lengths and sweep efficiencies mentioned are not applicable to miscible displacement in reservoirs. In this paper we present an evaluation of the gas-driven, LPG-bank oil-recovery process based on fluid flow experiments in areal models. These results are used to predict the performance of a field pilot test of this process, and the results are compared with the actual test results. THE EFFECTIVENESS OF LPG BANKS The effectiveness of LPG banks of various sizes in accomplishing miscible displacement of oil by gas was determined by displacement tests in a model representing one-quarter of a confined five-spot pattern. The model, 12 X 12 X 1/4 in. in size, was packed uniformly with glass beads. It was operated at a pressure of 1,550 psig and at room temperature; the fluids used were methane, propane and refined oil saturated with methane at 1,550 psig. The saturated oil had a viscosity of 1.2 cp at room temperature. The results of these tests are shown in Fig. 1, where recovery is plotted as a function of the volume of fluid injected for: (1) an immiscible-gas drive with an oil-to-gas viscosity ratio of 85; (2) three sizes of LPG banks; and (3) two completely miscible displacements with mobility ratios of 85:1 and 10:1. (The miscible displacement data plotted are the averages of several tests.) The results show that a 2½ per cent bank of LPG does not increase oil recovery over that obtained by immiscible-gas drive. The 7 and 17 per cent banks are, respectively, about 30 and 50 per cent effective (with reference to the M = 85 miscible-displacement curve) in increasing oil recovery at the point where 2½ hydrocarbon volumes (HV) of fluid have been injected. The percentage effectiveness of the banks at a given volume of fluid injected is defined as Recovery by Bank — Recovery by Gas Drive Recovery by Miscible Recovery by Flooding Gas Drive We conclude from these results that banks of LPG smaller than about 5 per cent HV in an individual stratum will cause from little to no increase in oil recovery. This finding was substantiated by work in low-pressure models, which permitted visual observation of fluid movements. In these tests, three completely miscible fluids having the same viscosity ratios as those used in

By T. F. Bower, M. C. Flemings

The classical explanation for formation of the fine equiaxed "chill zone " in ingot solidification is that local supercooling near the chill wall causes copious nucleation in this region. This work indicates, however, that convection is an essential element in formation of the chill zone. In the absence of convection, no chill zone forms even though rate of. heat extraction is extremely vapid. Alloy studied was Al-l.5 pct Cu alloy solidified against a copper chill wall. When solidification was initiated at the chill wall in absence of. cor-vection, surface grain size was large (>I cm diam). When it was initiated in the presence of convection, it was fine (<0.05 cm diam). It is concluded that some form of "crystal multiplication" plays an important role in formation of the chill zone. INGOT macrostructures are generally classed as containing one or more of the three zones: "chill zone", "columnar zone", and central "equiaxed zone". These three zones are sketched in Fig. 1; their origin has been discussed in some detail.&apos;-&apos; The classical explanation for formation of the chill zone is that supercooling occurs in the region of liquid metal adjacent the mold wall, and copious nu-cleation then takes place in this region forming numerous small crystals. The columnar region then results by growth of favorably oriented grains (den-drites) which crowd out their less favorably oriented neighbors."5 The mechanism of the columnar-equiaxed transition has been the subject of considerable interest. The generally accepted mechanism, until recently, was that constitutional supercooling developed in front of the growing columnar grains with eventual nucleation of new, equiaxed, grains ahead of the growing solid front.&apos; Recently, it became evident this explanation was not completely satisfactory and it is now evident that "crystal multiplication" plays an important role. This crystal multiplication occurs by separation of dendrite arms from growing dendrites,8?"&apos; and has been shown to be strongly influenced by convection.6, 10-13 Reduced convection results, for a given alloy, in longer columnar zone, larger columnar grains, and larger equiaxed grains.7, 12

Jan 1, 1968

By E. G. Woods, A. G. Comer

A mathematical model is presented and solved for determinution of the saturation distribution and pressure in a radial gas-storage reservoir. The model consists basically of two parts: (I) the growing gas-bubble core, and (2) the surrounding aquifer. Since the total pressure at the injection well is a function of the two-phase flow in the gas bubble and the unsteady single-phase flow in the aquifer, the resistance to flow in both zones was taken into consideration. The assumptions involved for both the radial equivalent of the Buckley-Leverett two-phase-flow equation and the injection-pressure equation are as follows: (I) the geometry is radial, (2) the gas bubble is free to expand or contract, (3) compression or expansion of the gas within the bubble may occur at the beginning of a time step, (4) the fluids are immiscible, (5) water is incompressible within the gas-storage region whereas it is compressible outside of this region, (6) a stable gas-water interface exists and (7) gas injection occurs at a constant rate or a series of constant rates. The mathematical model was solved numerically using an IBM 650 computer. A comparison is presented between the predicted results of the model, the results assuming steady-state flow and the actual initial injection-pressure history of an operating reservoir. Using the initial field pressure for a basis, the average deviation between the predicted pressure and the actual field pressure was less than 4.3 per cent. INTRODUCTION Underground storage of natural gas in abandoned oil fields, in abandoned coal mines, in caverns and in aquifers has had varying degrees of success. The lack of these first three facilities in the vicinity of most major gas marketing areas is leading more and more to storage in virgin aquifers. For the most part, this storage in aquifers has led to the study upon which this paper is based. Several excellent papers have been published discussing the problems involved in the underground storage of natural gas; however, to these writers&apos; knowledge, none of them considered the two-phase flow of fluids in the gas bubble and the fact that the gas bubble will grow or shrink in size depending upon the injection and withdrawal history of the reservoir. Not only will both of these factors influence the required injection pressure, but also they will have a definite bearing upon the amount of water production occurring upon withdrawal from the storage area. To solve this problem on an IBM 650 computer, several simplifying assumptions were made. Only the drainage portion of the relative-permeability curve was considered, thereby neglecting any hysteresis effects introduced during an imbibition cycle. The quantity of gas withdrawn during the period of the field study was only a small percentage of the total gas in place; therefore, this assumption is justified. For the problem studied in this case, the combined effects of capillarity and gravity were assumed to be negligible. This assumption becomes less valid as the formation thickness or the average pore diameter increases markedly. The justification of these assumptions should be studied in each case. THEORY This mathematical model for the prediction of saturation distribution and pressure for a radial gas-storage aquifer is based upon the equations for radial two-phase fluid flow&apos;.&apos; and for radial, unsteady-state, single-phase fluid flow.&apos; The two-phase flow is considered to take place in a "core" whose radius is equal to the maximum radius that the gas zone will attain, as indicated in Fig. 1. The injection-withdrawal history is approximated by a series of constant flow rates. Within the "core", gas is assumed to behave as a semi-compressible fluid; that is, the gas is assumed to have a constant density based on the average gas-zone pressure for the flow period. Between each constant-rate time increment, the gas density is allowed to change. This involves an iterative solution of the pressure equation. The liquid phase in this zone is considered to be incompressible, whereas it behaves as a compressible liquid outside of this region. The equations of incompressible flow in the "core" may be written for the gas phase

By W. B. Potter

THERE is probably no more interesting group of mineral fuels to be found in any country than that occurring within the limits of the new State of Colorado. The supplies are so abundant, and the occurrence and distribution are so favorable for easy development and transportation to the future manufacturing centres of the State, that they are destined to play a very important part in the material growth and prosperity of the region, the more so because of the rich and varied stores of ores awaiting metallurgical treatment, and the comparative scarcity of timber for fuel. From a purely scientific point, also, these lignitic coals form an interesting and important series. An examination of their geological occurrence and relations opens up new and important questions regarding the comparative value of various kinds of geological evidence, while a study of the character and composition of this class of fuels, which forms a connecting link, as it were, between the lignites and the true bituminous coals, may lead to a more thorough and accurate classification of mineral fuels. The analyses here presented are from samples, of not less than fifty pounds each, obtained by myself during the summer of 1875, and may be regarded as representing very fairly the average run of

Jan 1, 1877

US 4,183,899 - Flow process for chlorinating ilmenite. A laminar flow of a mixture of ore, a carbonaceous reductant, and chlorine gas or other chlorinating agent is passed through a reaction zone maintained at a temperature of 1350 to 1950°C and a product stream Including titanium tetrachloride is withdrawn from the zone. The atomic ratio of carbon to oxygen in the feed mixture is greater than 1:1, and the molar ratio of chlorine to titanium solids In the product stream is between about 0 5.1 and 2:l. Titanium chlorides and metallic iron are recovered separately from the product stream. J.P. Bonsack, assigned to SCM Corp, Jan. 15, 1980 21 pp. (423-79). Filed. 3-10-78 (885,442).

Jan 1, 1982

Beverley S. Randolph, Frostburg, Md. (communication to the Secretary): It has always appeared to me that each coalseam has its peculiar character or habit, due to the conditions of its formation, by virtue of which it is either persistent or variable in its section over extended areas. One seam will hold its thickness, chemical character, number and position of partings, beds of slate, etc., over a large area, while another will be found to vary in some of these characteristics every few feet. As the position of the outcrop is an accident of the topography, depending on folding and erosion which have taken place since the bed was formed, no one opening in the outcrop, or, in fact, anywhere else, can supply reliable evidence as to the general character of the seam. To determine the character of an untried seam, a number of sections are necessary from widely separated points, in order to show such variations as may exist. Should material variations be developed, more numerous sections are necessary, in

Jan 1, 1901

By A. F. Crawley

THIS communication reports measurements of the densities of dilute liquid alloys of 0.1 and 0.5 pct Ag in Sn over temperature ranges of 170" and 210°C, respectively, above the melting point of pure tin (232°C). The work was earried out to provide accurate density data for some liquid diffusion studies performed by Davis.1 Densities were measured using a pycnometric technique established in this laboratory. Earlier papers2, 4 attest to the accuracy of ±0.05 pct and the reliability of the method. Tin, 99.999 pct pure, and silver 99.99 pct pure, were melted in a graphite crucible in a vacuum furnace and held at temperature for 10 hr to ensure homogenization. Ingots suitable for machining

Jan 1, 1970

By D. A. Stevenson, R. A. Burmeister

Single-phase silver antimony telluride has been prepared by zone-melting techniques using initial compositions of A new phase appears upon prolonged annealing of this material, but the reaction does not appear to be a simple eutectoid decomposition. A complete analysis of the phase equilibria is complicated by the slow kinetics involved. The Hall coefficient, magneto -resistance, electrical resistivity, and Seebeck coefficient are all sensitive to the presence of second phases. The low Hall mobilities measured for single-phase material indicate that the usual band theory is inadequate to explain the observed transport properties in the system. Density anomalies of up to 2.5 pet between measured and theoretical density were observed but are not conclusive evidence for a defect structure. COMPOSITIONS in the Ag-Sb-Te system have been studied previously by several investigators.1"18 The interest in this system arises from potential thermoelectric applications of alloys on the Ag2Te-Sb2Tes vertical section. Although the composition corresponding to the formula AgSbTe, has received most attention, it has been found to consist of more than one phase.7&apos;8 A thorough understanding of the properties of this heterogeneous material has been impeded by both lack of knowledge of the properties of the homogeneous phases comprising it and the problem of analysis of transport properties in an inhomogeneous system. The present work describes the preparation of the homogeneous ternary phase and the corresponding electrical properties of both homogeneous and heterogeneous material. MATERIAL PREPARATION Most specimens for this investigation were prepared by encapsulating the elements in evacuated quartz tubes after which they were melted and homogenized in the liquid state. The ambient temperature was then dropped to 500°C and the resulting ingot zone melted. The growth rate, width of zone, stoichiometry, and number of passes have an effect on the resultant microstructure. Grains several centimeters in length were easily produced by this method. Other solidification techniques were also used, including uniform slow cooling of the entire specimen and rapid freezing. The microstructures of specimens produced by these techniques frequently differed appreciably from similar compositions prepared by zoning. A variety of nonequilibrium microstructures characterized by long needlelike particles resulted from the rapid-freeze method. PHASE EQUILIBRIA The lack of information on phase equilibria is a major difficulty associated with a comprehensive study of the Ag-Sb-Te system. Considerable confusion has resulted from the use of the formula AgSbTe, to identify the cubic ternary intermediate phase even though it has been established that material of this stoichiometry normally contains AgzTe as a second phase.798 In this paper, silver antimony telluride will denote the cubic ternary intermediate phase comprising the major portion of AgSbTe,. The term "single phase" will denote material which consists of only the cubic phase (as evidenced by metallographic examination and X-ray diffraction) and the term heterogeneous will describe multiphase material containing AgzTe, SbzTe3, or other phases in addition to the cubic phase. The single-phase material may actually contain a variety of inhomogeneities—gradual changes in composition on a macroscopic scale, localized fluctuations in composition, clusters or other products of early stages of the precipitation process, and a variety of point and line defects—all of which will not be detected by the present techniques for determining homogeneity. Single-phase material has been prepared from compositions close to 59 mole pct SbzTe3 21 (this notation refers to the location on the Ag,Te-Sb2TeS vertical section). Zone widths of =2 cm and growth rates 51.2 cm per hr were used. The single-phase region at elevated temperatures extends off the vertical section to a composition which can be expressed approximately as Ag,,SbzgTes,.9 The latter two compositions as well as AgSbTe, are represented in the conventional Gibbs triangle in Fig. 1. It is not presently possible to ascribe exact values to the limits of the single-phase region on a given isotherm or vertical section due to the extremely

Jan 1, 1964

By E. T. Turkdogan, P. Grieveson

Experimental results are presented for the rate of solution of nitrogen in a iron in the temperature range 750° to 873°C and in 6 iron in the temperature range 1410° to 1470°C. It is shown that the rate controlling process is diffusion of nitrogen into the iron. The diffusiting of nitrogen in a and 6 iron is derived from the results, and the temperature dependence of the diffusivity is represented by the equation D = 7.8 x e- 18,900/RT sq cm per sec. The solubility of nitrogen in a and 6 iron, in equilibrium with 1 atm pressure of nitrogen, has been measured. Using these results and other available data, it is found that the variation of the logarithm of nitrogen solubility with the reciprocal of absolute temperature is nonlinear. In an Appendix, some results of Darken and Smith are presented for the rate of solution of nitrogen in iron using ammonia + hyidrogen mixtures. These data also support the view that diffudsion of nitrogen in iron is the rate-controlling process when ammonia + hydrogen mixtures are used. A considerable effort has been made to obtain data on the solubility1-5 and diffusivity of nitrogen in a iron6-l2 because an understanding of the effect of nitrogen on the properties of steel must be based on an accurate knowledge of the properties of nitrogen in pure iron. However, no information is available concerning the kinetics of solution of nitrogen in a and 6 iron. Recently the authors13 have investigated the rate-controlling mechanism operating in the kinetics of solution of nitrogen in y iron. This study was directed to determine the rate-controlling processes for similar reactions with a and 6 iron as well as to establish values for the solubility of nitrogen in equilibrium with nitrogen gas in a and a iron. EXPERIMENTAL The procedure used in experiments to determine the rate of solution in cylindrical iron rods was the same as that described in a previous communication.13 Ferrovac E grade iron used in all experiments contained the following impurities in weight percent: C, 0.005; Mn, 0.001; P, 0.002; S, 0.006; Si, 0.006; Ni, 0.025; Cr, 0.002; V, 0.004; W, 0.02; Mo, 0.01; Cu, 0.001; Co, 0.01; 0, 0.007. After cleaning the surface, the iron rods were treated in an atmosphere of purified hydrogen for 17 hr before the reacting gas was introduced for known experimental times. After quenching, the samples were sectioned radially and analyzed for nitrogen. In addition to experiments using rods, iron foils were used in the measurements of solution rates of nitrogen in a iron. The foils of two different thicknesses were prepared by cold rolling Ferrovac E grade iron cylindrical rod to 0.051 and 0.152 cm. Foil samples were used in a rectangular form 5 cm long and 1.25 cm wide. The specimens were thoroughly cleaned of surface oxide with fine emery cloth and degreased with carbon tetrachloride immediately before entry into the furnace. The experimental procedure was the same as that used in the study with rods. At the completion of an experiment, the foil samples of the nitrogenized iron were analyzed for nitrogen after discarding 0.3 cm from the perimeter of the specimen. Iron foils were nitrogenized and denitrogenized in the a and 6 range with a gas mixture of 95 pct N and 5 pct H for times varying from 5 min to 2 hr. Results obtained for the average composition of nitrogen in iron for these experiments are presented in Fig. 1. Prior to the denitrogenization experiments, the samples were saturated with nitrogen at 1000°C and 0.67 atm N, giving a uniform nitrogen concentration of 0.0204 pct. According to the known a-y phase boundary in the Fe-N system,14 this composition lies within the ferrite region at temperatures 750" to 850°C. Use of this initial nitrogen content insured that reaction occurred between the gas and a single solid phase, a iron. Examples of the results for the mean concentrations of nitrogen in cylindrical iron rods, 0.356 cm radius for both the a and 6 ranges are given in Fig. 2. Typical examples of the results obtained for the radial distributions of nitrogen in rods are presented in Fig. 3. It appears that the results for radial distributions can be extrapolated to constant surface compositions which agree with the equi-

Jan 1, 1964

By W. B. Potter

There is probably no more interesting group of mineral fuels to be found in any country than that occurring within the limits of the new State of Colorado. The supplies are so abundant, and the occurrence and distribution are so favorable for easy development and transportation to the future manufacturing centres of the State, that they are destined to play a very important part in the material growth and prosperity of the region, the more so because of the rich and varied stores of ores awaiting metallurgical treatment, and the comparative scarcity of timber for fuel. From a purely scientific point, also, these lignitic coals form an interesting and important series. An examination of their geological occurrence and relations opens up new and important questions regarding the comparative value of various kinds of geological evidence, while a study of the character and composition of this class of fuels, which forms a connecting link, as it were, between the lignites and the true bituminous coals, may lead to a more thorough and accurate classification of mineral fuels. The analyses here presented are from samples, of not less than fifty pounds each, obtained by myself during the summer of 1875, and may be regarded as representing very fairly the average run of

By J. G. McCullough

The paper is a general description of the U.S. lead and zinc industries as they are now compared to ten years ago and the effect of recent world-wide developments. Topics of interest concerning lead are the present and potential growth of the lead-acid battery business, the potential hazards of having one outlet for a major proportion of production, the expanding U.S. secondary lead production, the hardships of stringent hygiene and environmental regulations and the future supply and demand outlook. The present poor condition of the U.S. zinc industry caused by an oversupply of zinc metal - mostly in Europe - is discussed and also the shifting markets influenced by the automotive programs to reduce the weight of cars and the continuing high mine production due to the mixture of metals contained in the massive sulphide deposits which contain a major portion of the zinc metal reserves. This is all tempered by technical advances in die casting and the emphasis on the protecting of steel with zinc to prolong its useful life. New U.S. mine and smelter production facilities will be restrained due to lower cost foreign zinc from better grade ore deposits and the insistence by Governments for refining capacity to be constructed in the country that the ore is mined.

Jan 1, 1977

By Karl W. Mote

CALIFORNIA&apos;S iron and steel industry had its beginning in San Francisco in 1849 when the first iron casting was poured at the old Union Iron Works. Soon after, in 1856 at Grass Valley, enough iron ore was smelted to supply pig iron for the castings of a quartz mill there. From 1880 to 1886, iron ore was produced from the Hotaling mine in Placer County and converted to pig iron in a local blast furnace using charcoal. From 1907 to 1914, the Noble Electric Steel Co. produced pig iron from iron ore mined at the Shasta Iron Co. mine, and followed this for three years in the production of ferro-alloys. Between 1917 and 1941, the State&apos;s industry in- creased its capacity for open hearth and electric furnace scrap treatment, but the real impetus was supplied by the need for more steel at the beginning of World War II. The result was the State&apos;s first integrated steel plant-the Kaiser Steel Corp. facilities at Fontana.

Jan 7, 1958

By Campbell Osborn

FROM the viewpoint of practical economic engineering the main value in studies of demand and supply lies in the information they give concerning the next movement of price. The title of this discussion is too comprehensive for detailed analysis and it will, therefore, be narrowed to the question of price measurement. The oil operator is interested primarily in net profits. Prices, costs and production determine them. Production is here used in its broadest sense. It includes refining and marketing. It is an operating problem. Prices and costs are economic considerations. Though costs are an important element of prices and profits, the subject is too large to be treated in a brief paper of this sort. In the long run, costs govern prices, but for the purpose of gaging prices in the immediate future the relationship of current demand and supply are more significant. Operating, expansion, retrenchment, sales and storage policies of oil companies are largely influenced by the feeling of executives concerning this relationship. The stockholders of companies whose executives are wrong may suffer. Investors who err in their judgment may likewise lose. On the other hand, oil companies and investors who appraise these factors correctly and move accordingly will profit. It is an important subject worthy of careful consideration.

Jan 1, 1928

By Harry A. Wahl

Precent fracture design procedures are bared on the total fracture area created. A method to distinguish beI,,.ecn total area and [he propped or effective fracture area has not been available. This paper presents a solution to this problem, applicable to horizontal fractures. The difierences between effective fracture area and torn] area are demonstrared in example calculations. This work is hayed on experimentally determined transport efficiencier of solids in sand-liquid slurries. Newtonian and non-Ne~vtoninn systems are considered. INTRODUCTION Fifteen years after commercial introduction, hydraulic fracturing remains the most successful stimulation technique in the oil field. This success is primarily due to ability of induced fractures to penetrate and alter permeabilities deep within formations. Many fields producing today could not have been developed without the hydraulic fracturing process. Because of wide usage, fracture-treatment design has received a great deal of engineering and research effort. This work, resulting in improved equipment and materials, has increased the benefits from fracture treatments as well as the applicability of the process. A major contribution was the development of fluid-loss additives. Necessarily, the number of parameters to be considered in treatment design has steadily increased, resulting in more complicated design techniques. Almost all present design procedures are based on the precepts set forth by Howard and Fast. Relating the fluid volume lost into the formation, the volume required in extending the fracture, and the total slurry volume injected, they developed an expression for the total fracture area created in terms of pertinent treatment parameters. Fluid loss during treatment was expressed as a function of time for three flow mechanisms. Although modifications of fluid loss equations have been made, the total fracture area concept has remained unaltered. A vast amount of field data indicate that induced fractures must be propped and held open to be effective. A notable exception is the Mesa Verde formation in the San Juan basin. However, analysis of these treatments shows that improved well productivities are obtained when propping agents are incorporated in the treating fluid. Although propped fracture area has been recognized as an important design parameter, a method to distinguish between total area and effective fracture area has not been available. The necessary information on slurry-sand transport in fractures has been lacking. Interest in the propped region of induced fractures is not restricted to areal extent alone. The distribution of sand within fractures is important from the standpoint of fracture flow capacities. Flow capacity affects the increase in well productivity after stimulation. The work of Huitt and Darin4 hows that partial monolayers of sand have large flow capacities compared to thick* dense sand packs. It has been postulated that gelled fluids have the ability to transport sand within the fractures at the deired low concentrations. An early contribution in the area of sand placement in fractures was made by Kern et al.&apos; They studied sand movement in a transparent vertical fracture model. It was observed that the sand tended to settle out in the bottom of the model before moving very far. When the fluid velocity exceeded a certain critical value, all of the sand injected began moving through the crack even though it settled to the bottom. This critical velocity was determined under several flow conditions. Some work on sand movement in horizontal fractures has been reported in Russian publications. Sand movement was studied by Izyumova and Shan&apos;gin&apos; using a transparent "pie-shaped" flow model to simulate a horizontal radial flow system. However, the data were limited, especially in a quantitative sense. Dorozhkin, Zheltov and Zheltow studied the behavior of sand-liquid slurries in a horizontal linear flow model. The quantitative data were restricted primarily to the thickness of sand deposits formed at the bottom of the fracture. An earlier paper provided basic data on the flow of sand in horizontal fractures. This study was designed to yield specific quantitative information on rate of advance of sand particles and pressure behavior under various flow conditions. A comprehensive photographic study was undertaken in a 10-ft windowed flow cell to provide the necessary qualitative and quantitative data. Since the number of potential variables far exceeded the capacity of the initial study, emphasis was placed on the effects of sand concentration, oil viscosity and oil flow rate. A detailed description of these experiments and the results are described in Ref. 9. However. the implications of this work on the fracture design calculations were not discussed. An analysis of these data as well as new data is provided in the following sections. EXPERIMENTAL RESULTS The primary objective of the experimental investigation was to provide information on the rate of advance of the solids in sand-liquid sturries. A 10%-ft long transparent

Jan 1, 1966

By C. J. Leith

A study of the effect of rock composition, rock structure and degree of weathering on the stability of cut slopes is being sponsored jointly by the U.S. Bureau of Public Roads and the North Carolina Highway Commission. In 58 mountain and piedmont counties of North Carolina the percentage of failed cut slopes is greatest in micaceous metasediments, gneisses, and schists, and in saprolite and soil derived from these rock types. Soil slope failures outnumber rock slope failures by two to one. Joints and similar planes of separation exert a strong influence on size and shape of the sliding mass. They may or may not act as failure surfaces, depending on their orientation with respect to the active forces. Climatological data, though indicative of weathering conditions, do not correlate well with slope failure frequency. Because of the presence of joints and similar planes of weakness in soil and rock materials, conventional methods for analyzing slope stabilities are not directly applicable. Empirically derived modifications of these methods are being investigated. A study of the stability of highway cut slopes, sponsored by the U. S. Bureau of Public Roads and the North Carolina State Highway Commission, began in 1962 at North Carolina State of the University of North Carolina at Raleigh. As part of this study all slides, rockfalls and other types of cut slope failures on Federal and State highways in the 58 mountain and piedmont counties in North Carolina were located and described, and the data catalogued in a punched card file system. A major objective of the project is to relate slope failures to properties and physical conditions of the geological units in which the slopes were constructed, and to correlate soil type and/or geological unit with type and frequency of slope failure. The complexities of the problem of slope stability and the limitations which these complexities impose on methods for analyzing slopes have been recognized for many years. A great variety of factors and processes may lead to slides, often making it almost impossible to analyze theoretically the conditions required for stability of slopes. One of the principal factors determining maximum safe slopes is the shear strength of the material in which the slopes are cut, but unfortunately there are very few data available concerning shear strengths of residual soils. Vargasl tested clay derived from gneiss and granite in southern Brazil; the properties of decomposed granite occurring near Hong Kong were determined by Lumb.2 These data are being used, when applicable, to supplement the test data obtained in the present study by Yorke.3 The locations of the North Carolina slope failures, more than 400 in number, are shown on Fig. 1. This map, adapted from the Geological Map of North Carolina,4 suggests the possibility of a relationship between frequency of slide occurrence and rock type. However, the evaluation of this possibility requires consideration not only of the type of rock, but also of its large and small scale structural features, its susceptibility to and degree of weathering, and the composition and structure of the weathering products. Soil slope failures in thoroughly weathered soil material and saprolite outnumber rock slope failures two to one. INFLUENCE OF ROCK TYPE The agricultural soil type involved in each soil slope failure was identified and each failure was catalogued in terms of the parent material from which the soil was derived. These data indicate that most of the slope failures, whether in the rock or in the derived soil, are associated with metamorphic rocks (see Fig. 2a). The data may be skewed somewhat because of the relative sizes of the total areas underlain by the various rock types, but Leith and Gupton5 have demonstrated that the preponderance of failures in metamorphic rocks is of much greater magnitude than could be accounted for by the areal factor alone. The dominance of metamorphic rocks is emphasized when soil slope failures are considered in terms of the specific rock types from which the soils were derived (see Fig. 2b). In particular, mica schists and mica gneisses account for more slides

Jan 1, 1965