Search Documents

By Creasey J. W, Huntington J. F

Faults cutting the Lithgow and Katoomba seams in some collieries of the Western Coalfield can be classified, on the basis of spatial pattern, into three principal groups: meridional swarms of closely spaced minor faults and associated joints, with throws of less than 0.5 m and with exceptional faults of up to 5 m; isolated interswarm strike-slip faults in the Lithgow seam and widely spaced strike-slip faults in swarms in the Katoomba seam; and low-angle normal faults associated with the Lidsdale-Lithgow seam split.Orientations of faults and coal cleats in the coalfield are presented on stereoplots and histograms, as a basis for an analysis of fault dynamics. The low-angle normal faults were found to have been formed only along the Lidsdale-Lithgow seam split, and before the high-angle faults. The origin of the high-angle normal faults in the meridional swarms is discussed and it is suggested that basementcover interactions must have occurred. This suggestion is supported by geophysical evidence. Low-amplitude monoclines in the coal seam, and the spacing of swarms 0.9 to 4.5 km apart, may be due to the underlying basement structure.It is clear that postextensional compressive deformation of swarms in the coalfield gave rise to shortening by minor thrust development, and probably also caused the synchronous strike-slip movement on pre-existing normal faults. There is evidence to show that isolated interswarm strike-slip faults in the Lithgow seam, and widely spaced strike-slip faults in the Katoomba seam, may have originated synchronously with such thrusts. The axis of maximum principal compression ('71) for the thrust event was inferred to be near horizontal and aligned approximately E-W. Recent rock mechanics measurements of the present day stress field indicate a similar stress configuration.

Jan 1, 1981

Ammonium nitrate-fuel oil (ANFO) explosives are unstable in hot, reactive sulphide-rich ground at Mount Isa. Under certain conditions associated with background heat, moisture, and chemical impurities from natural oxidation, ANFO composites in contact with hot ground disproportionate and the ammonium nitrate can undergo rapid exothermic reactions with sulphide.Reactions can occur in confined charges from prolonged contact with reactive sulphides, or by contamination with sulphide in loading. Partial interaction can result in misfires or premature detonation. Spilt, scattered and unpropagated explosive will undergo further reaction in sulphide-rich environments. ANFO-sulphide interaction is invariably exothermic and causes an irreversible chemical transformation of the ore.The heat generated during reaction may be dissipated, heating the environment, or rapidly accumulated to yield hot spots or areas in excess of 400°C. These can result in forced ignition of bulk sulphide and sustained combustion.Thermal analysis was used to define the critical conditions for ANFO-sulphide interaction and sulphide combustion.The occurrence of incandescent ore is attributed to the thermal interaction between exothermic hydrolysis oxidation, ANFO-sulphide, and combustion processes.Chemical agents and control methods have been developed to prevent ANFO-induced oxidation and combustion.

Jan 1, 1968

By Barclay C, Jacobsen M, Towsey C

The Emperor Gold mine at Vatukoula, Fiji, is a nine million ounce gold telluride deposit. In January 1992, the mine was on the verge of closure when the current management team took charge. Losses had been incurred for two consecutive years and the published resource amounted to less than five years of production. Relationships with the workforce, the government and the general public were poor. Today, the mine has recorded three consecutive years of profit, has resources that will support the operation for at least 20 years and has excellent relationships with employees, government and the general public.

Jan 1, 1997

By P Luo, J E. Danoczi, P Nakutnyy

Sensor-based sorting methods to remove waste or for upgrading ore prior to downstream metallurgical processing is becoming more prevalent for mining operations. X-ray transmission (XRT) sorters are a popular choice for mineral processing plants since they can sort a wide variety of minerals. XRT sorters pass high intensity X-rays through particles to generate images of varying greyscale, based on their effective atomic density. The ore sorter then mechanically separates the particles using algorithms based on the images. A popular test currently used to evaluate the amenability of the ore to XRT sorting is to pass the particles through the sorter and obtain the greyscale images showing mineralogical differences. This test provides information on the mineralogical heterogeneity between ore particles for their separation. However, it does not provide an understanding of the actual mineralogical composition of the ore or information pertaining to which other minerals may respond in a similar manner, nor does it provide liberation information. This paper describes a test that combines high resolution X-ray micro Computer Tomography (CT) combined with QEMScan to obtain information about amenability of ore to XRT sorting and to obtain valuable information that can streamline metallurgical testwork programs. This test also provides information relating to particle thickness and associated X-ray attenuation coefficients, desired mineral presence and mineralogical information relating to associated minerals and clays to assist with developing sorting algorithms. Combining the CT and QEMScan can address many limitations of the current method to determine whether XRT sorting technology is appropriate for particular ores. Mineralogy information from QEMScan can identify incidences of; mineral encapsulation, problematic clays, detrimental minerals as well as calibrate the greyscale values of CT data. Additional 3D CT imaging carried out on cores provides spatial information of the minerals within the ore and mineral grades.

Nov 10, 2020

There are many compelling reasons why correct sampling schemes should be standard practice in the mining industry, yet there are numerous examples where poor sampling practices are known to exist in the business yet permitted to continue. It is not just technical issues that can be ascribed to the reasons for the continued use of incorrect methods. This paper proposes non-technical reasons why incorrect sampling practices continue, and identifies potential ways to overcome them.

Mar 1, 2010

Were it simply a matter of extracting tin from the simple tin sulphide, the proposition would undoubtedly be simple enough. When, however, other valuable metallic sulphides are combined with the tin, and it is required to separate these intomarketable products, then the proposition becomes somewhat complex, and such is the case with the class of material of which I am about to write. The locality where it occurs is Howell, New South Wales, and chiefly at the Conrad Silver-Lead Mine. The tin sulphide occurs chemically alloyed with copper, iron and other metals associated with galena, pyrites, mispickel, blende and silver sulphide in varying proportions, and generally in a gangue of highly crystallised quartz.Several varieties of tin sulphides occur, and from the following analyses of three minerals, these being specimens specially selected free from foreign matters, it will be seen that the chemical composition is somewhat complex.

Jan 1, 1902

It is no longer adequate when starting a new mine to simply select the best equipment. Today's competitive international commodity markets demand superior efficiency which requires systematic involvement of people in continual improvement of production and commercial processes. True Total Quality of Management (True TQM) principles provide an operating philosophy for maximising productivity and minimising unit costs of output. The presentation will show the practical and successful use of these principles. This paper will introduce the case study and provide background material on True TQM.

Jan 1, 1995

By J E. Askew

The rapid expansion of gold production in Australia over the last five years can be attributed in part to the development of selective mining techniques for open pit gold operations. These techniques allow an increase in head grade with a substantial reduction in mill feed tonnage, as compared with traditional open pit designs. As a result, the capital requirements for mine development and mill construction are substantially reduced, improving the cash flow profile in the early years of operations. To put such a design into effect, the emphasis of mine production must be on producing gold, rather than tonnes of ore. Mine planning at Martha Hill has been based on such a philosophy. After the quantity and grade of the resource had been defined, the exploration programme was increasingly concerned with the local variability of ore zones, and with determining the position of values within broad ore-definition envelopes. The purpose of this work has been to allow the prediction of the tonnages and grades achievable from various levels of the pit when mining selectively using hydraulic excavators. The studies have so far indicated that the Martha Hill deposit can be mined selectively during the early years of production. The additional costs for detailed grade control and a reduced digging efficiency are more than compensated by the exclusion from the mill feed of much valueless material.

Jan 1, 1986

By L Vimercati, R Williams

Transitioning to a green future requires the mining industry to adopt sustainable practices. Filtered tailings are become a key expectation of the communities we operate in and are growing in a number or mining commodities including bauxite, nickel, gold and iron ore. The filtration technologies required range from dewatering screens to vacuum and pressure filters. Particular challenges faced in iron ore applications include large scale which means several units of large size are often required. In addition, a high specific gravity that cause sedimentation issues and a high abrasion level make demands on achieving reliability level at above 90 per cent. This paper describes the testing, selection criteria and specific features required to provide a rational option for equipment and plant design. An example of how this has been applied in an iron ore application in Brazil is used to demonstrate a successful outcome. This project installed four overhead beam filter presses each producing around 200 t/hr utilising a recessed chamber plate, feed pressures up to 15 bar, cake thickness of 5 mm. The moisture lower than 20 per cent that was produced was considered to provide material with handling and geotechnical properties to guarantee a safe stacking. Regular high pressure washing at 100 bar was considered imperative to maintain cloth life and process performance. The correct management of the system (OPEX control) by PLC control ensures a balance between machine potentials and plant needs. With this equilibrium it is possible to limit mechanical wear preserving equipment lifetime.

Sep 18, 2023

By Holla L, Tyminski A

Stowing has been successfully used in many countries as a means of controlling surface subsidence, minimi ing incidences of spontaneous combustion, maintaining gate road stability and maximising coal recovery.Australian experience in stowing is limited but in the future increased extraction of thicker and/or multiple seams by longwall operations and resolution of conflict of alternative land u'ses may necessitate the use of stowing in coal mining. At present there is little incentive for mining companies to introduce and operate a stowing system because costs have to be borne by the individual companies and benefits spill over to society and the State. Cost sharing by the industry and State incentives may overcome the problem of cost disincentive.

Jan 1, 1987

The main asset of a mining company is the mineral resource; without resources there is no mining business and the infrastructure is useless. In this context the role of the mining geologist is to always keep the resource inventory to an optimum level for the mining business and to maximise the transformation of the resources into reserves in a multi- disciplinary work environment. In short, a ægood mining geologist has to always provide the best ore to the millÆ.To do his/her work properly, several technical skills are needed: to know how to observe and describe nature in order to optimise the data acquisition process, particularly when mapping; to have a good understanding of natural variability in order to develop proper sampling strategies and sample preparation protocols to minimise all the errors generated by the sampling process; to have a good understanding of assaying practices: their limitations as well as their assaying errors; to carefully and properly store the geological data and information and to preserve the geological patrimony; to fully understand ore forming processes to generate the best possible geoscientific models, which are fundamental for the mining business; to fully understand the consequences of the geoscientific models along the value chain from rock to cathodes; and to continuously validate and improve geological practices and models by continuous data collection and observation of geo- mining-metallurgy processes. Some very important behavioural competencies are also needed:long-term vision, passion for excellence and value generation, strategic influence, systemic and innovative thinking, and knowledge and experience transfer. Last but not least, it is important to point out that a deep knowledge of the mining business is essential to add value by using geology best practices.

Jan 1, 2006

By A M. Hagni

Certain copper ores from the Nchanga Copper Mine in the northern Zambia Copperbelt are refractory with respect to conventional beneficiation techniques. This paper reviews recent study of those ores to determine their mineralogy, textures and nature of copper occurrence. Two suites of refractory ores were selected for study: 1.  samples of stockpiled ores from an open pit, and 2.  drill core samples from copper ores. Both sample suites are from the upper orebody at Nchanga and contain about 0.3 - 1.4 per cent copper as determined by atomic absorption, but they represent separate stratigraphic, mineralogical and beneficiation problems. Ore microscopic examination showed that fine-grained copper sulfides are totally lacking from both suites of refractory ores. Petrographic study found malachite in the refractory ores from the open pit, but that malachite probably is post-mine. The opaque mineralogy of the open pit refractory ores is dominated by goethite that occurs mostly as pseudomorphic grains after pyritohedral pyrite crystals that average 200 - 250 ¦m across. Haematite occurs as bands within or as outer shells of the goethite grains. Additional goethite occurs locally as finer-grained areas of exotic goethite. The opaque minerals in the drill core refractory ores are dominated by euhedral ilmenite crystals about 50 - 175 ¦m long. Anatase is the dominant opaque mineral in some drill core samples where it is largely pseudomorphic after ilmenite crystals. Goethite accompanies malachite in unusual drill core refractory ores that have experienced intense hydrothermal alteration. Thus, ore microscopy and petrography showed that fine-grained chalcopyrite and bornite and pre-mine malachite were not the causes of the refractory nature of the ores studied. Electron microprobe revealed that most of the copper occurred in solid solution within micas. Application of automated SEM techniques has provided a detailed understanding of the distribution of copper in these refractory ores.

Jan 1, 2008

Satellite Image Based Strategies to Evaluate the Impact of Dismissed Mine Site - An Application to the Mae Moh Coal Mine Area in the Lampang Province, Thailand

Sep 13, 2010

This paper contains an account of some creep tests on electrolytic lead and some of its alloys. The stresses used in determining creep were 500, 350, and 200 lb. per sq.' in. The alloys contained silver, bismuth, tellurium, antimony and zinc respectively. All were castin vacuo, and tested "as rolled." Tests were done also on electrolytic lead which had been cast in air.The electrolytic lead contained 0.0005% total impurities.The preparation and vacuum casting of this lead have been described in a previous paper in this series. The preparation of the alloys, and the air casting of the electrolytic lead, are described in the next section.EXPERIMENTAL PROCEDURE.Every effort was made to keep the vacuum-cast specimens from contact with the atmosphere throughout their history.The ingots were stored eIther in a vacuum desiccator or immersed in heavy oil. The creep specimens were coated with vaseline except during rolling, etching and photography, which involved exposure to the atmosphere for about 45 minutes all told.It is not claimed that vaseline is a perfect shield against the intrusion of atmospheric gases. Possibly during the months that some tests were in progress the gases diffused through the vaseline and gained a limited access to the lead.Nevertheless, the use of vaseline gave protection that brought the tests nearer the ideal at which the author aimed, *Research Fellow, Dept. of Metallurgy, University of Melbourne.

Jan 1, 1936

By B Maybee

In underground mine planning, many potentially value-eroding decisions are made due to a lack of time and proper evaluation practices. The information required for mine planning decisions goes beyond external sources of uncertainty that are recognised by typical evaluation techniques used in the mining industry, to include technical factors (eg mine development layout) and the ability of a mineral extraction project to achieve its anticipated production levels. Due to the individual characteristics that define underground mining projects, each will exhibit a different risk profile, and thus advanced optimisation and evaluation techniques are required to capture this information.As underground mine planning tools become more sophisticated, mine planners have the capacity to investigate numerous mine sequencing options to identify the best strategy for a given project, creating higher value for shareholders. This paper describes a risk-based evaluation methodology (RbEM) that accounts for financial and technical risk in the evaluation of underground mining projects. While the use of the RbEM has been described in previous works, no benchmarking of the benefits that can be realised from a change in those decisions that are made early in the process has been undertaken. To show the benefits that can be achieved from using the RbEM, this paper updates a case study to which the RbEM was applied, and takes a retrospective look at whether additional value would have been gained by following the strategic recommendation of the RbEM versus a typical optimisation exercise that aims to maximise the net present value.CITATION:Maybee, B, 2012. Can a risk-based evaluation provide a more valuable mine design?, in Proceedings Project Evaluation 2012 , pp 53-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By K L. Temel, W P. Player

The underlying message of this paper is that investment in prospecting, exploration and mining in New Zealand is welcomed. The Government's policy with respect to Crown owned minerals is for continuing investment in prospecting, exploration and mining which is in accordance with good exploration or mining practice. To encourage continued investment requires a business-friendly environment. Government policies and initiatives to enhance the business environment for the minerals and coal exploration and mining industries are discussed in this paper. As well, new initiatives under consideration, which have the purpose of enhancing the investment environment, are discussed.

Jan 1, 1997

By H Thanasekaran, M J. Mankosa, J N. Kohmuench, G H. Luttrell

"Fluidised-bed flotation has been demonstrated over the last 16 years as an effective method for improving the flotation recovery of coarse particles. This technology has been successfully deployed into the industrial mineral sector with multiple installations within phosphate beneficiation plants and potash mills. Due to the minimal mineral surface expression required when utilising this technology, more recent studies have centred on the applicability of using this HydroFloat™ technology for the recovery of coarse sulfides and base metals. Multiple approaches have been investigated to determine the best means for implementing this novel coarse particle flotation system into both existing and new plant circuitry. These include the treatment of tailings to recover values that have been lost using conventional technologies and also the direct treatment of a coarse feed, either within the grinding circuit or by use of a separate split-feed flotation approach. Recent applications of the technology will be presented along with data generated from several test campaigns and ongoing research investigations. The benefits of properly applying this technology, such as reduced power consumption and increased mill capacity will be discussed.Citation:Kohmuench, J N, Thanasekaran, H, Mankosa, M J and Luttrell, G H, 2016. The Impact of Fluidised-bed Flotation for Treating Coarse Sulfides, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 105–112 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

A thermochemical model is developed to study the two-stage smelting reduction process for ironmaking without post-combustion. Steady-state multi-material and heat balance equations are solved simultaneously to study the effect of metallisation, slag basicity, coal rank and heat loss on consumption rates of coal, ore, flux and oxygen and production rate of slag to produce hot metal of a given composition, tapped at a given temperature. The model is applied to the commercial data for a COREX-plant producing a wide range of hot metal compositions, tapped at different temperatures. The computed rates of coal, slag, flux, ore and oxygen were found to be close to the reported ones, but an exact match could not be obtained. It is found that a four per cent change in metallisation brings changes the coal rate by five per cent, flux rate by six per cent, slag rate by eight per cent and oxygen rate by 13 per cent, while a ten per cent change in basicity changes the coal rate by ten per cent, flux rate by 13 per cent and oxygen rate by 22 per cent. Further, it is found that an increase in metallisation decreases the coal rate and export gas. At a given per cent metallisation, the coal rate and the export gas are lowest for anthracite compared to all other types of coal.

Jan 1, 1999

By Little T. N

The Western Australian School of Mines is continuing to investigate the blasting techniques and mining strategies that are used for ore/waste separation (or high grade/low grade ore separation) or to prevent ore and waste mixing. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and undergoes no mixing of the various identified ore and waste blocks and is fully recovered at the minimum overall operating cost. The current study includes the use of computerised Knowledge Based Systems (KBS) technology to assist the user with the blast technique selection and blast design process. These aspects are highly dependent on the geology. (geometry, rock mass properties, grade distribution), explosive performance and the expectations of the mining company in terms of production rates and equipment utilisation. Most of these factors are not well defined and nor are they easy to quantify. However, a large amount of knowledge does exist and is available in the following forms: rules of thumb, empirical formulae, engineering judgement and past experience. KBS techniques are well adapted to handle such"forms of knowledge. The primary objective of this paper is to illustrate an approach for the use of Knowledge Based Systems during the analysis and interpretation stages of the blast design process. In particular, the components and methodology of the developed system are described for selective open pit gold mining. The Knowledge Based System developed was written using the declarative programming language PROLOG.

Jan 1, 1990

By P A. Montoya

La Colosa is a world-class porphyry Au project located in Colombia, currently undergoing prefeasibility analysis. As part of collaboration between AngloGold Ashanti and the AMIRA P843A GeMIII Project, the application of emerging geometallurgical characterisation testing and modelling tools has been incorporated in early stages of project development. The aim of the geometallurgical study is to map inherent comminution variability across the La Colosa deposit providing information critical for mine/mill design and optimisation. In this study, site-based data incorporating multi-element assays, quantitative analyse X-ray difraction QXRD bulk mineralogy measurements, EQUOtip rebound hardness data, and routine geological logging information from 59 diamond drill holes has been integrated with a range of geometallurgically specific comminution test (ie GeMCi, A × b, BMWi). The work in this paper demonstrates the integration techniques used at La Colosa to link routine data acquisition methods with comminution test results through the development of proxy support models. The integration incorporates a range of statistical techniques including principal component analysis and regression modelling. By creating proxy models, comminution index estimates can be propagated into the geological database enabling comminution processing domains to be defined. These domains provide the first spatial representation of comminution performance and variability at La Colosa and can be compared against traditional geological domains. This study provides the foundation for ongoing comminution characterisation as the La Colosa project evolves through project cycles into an operational mine.

Sep 5, 2011