Search Documents

By R L. Brathwaite

As part of an investigation of the deep structure of the Waihi Basin, an extensive set of resistivity measurements was recently collected by DSIR Geology & Geophysics. The objective of this work is to map deep resistivity changes throughout the Waihi area in order to contribute to a better understanding of the regional geophysical structure. This research is also aimed at improving techniques for locating 'deposits of epithermal mineral resources, and helping to establish their origin and genetic relationship to fossil geothermal systems.   The results indicate that the basin south of Waihi is underlain by an extensive layer of low resistivity, modelled as a 5ohm-m layer several hundred metres thick. Lake sediments (mudstones), as exposed in the south western part of the basin, near Waitawheta, are the most likely source of this low resistivity layer, although hydrothermally altered clays and/or elevated temperatures are other possible causes. Strong northeast trending anisotropy is also observed, implying structural links from Waitawheta through to Golden Valley. The observed resistivity pattern is consistent with a æburied calderaÆ or æfaulted depressionÆ structural model for the basin, as inferred from gravity and magnetic data.

Jan 1, 1991

By M Sciortino, J Korczak, J Muinonen, A St-Jean

The Dumont deposit is a large (1179 Mt reserve), low-grade (0.27 per cent nickel) nickel sulfide project located in the Abitibi region 25 km west of Amos, Quebec. Royal Nickel Corporation (RNC) acquired the project in 2007 and has since taken the deposit through to feasibility. The disseminated nickel sulfide and alloy mineralisation is hosted within the serpentinised dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinised, ultramafic sill of komatiitic affinity. Pentlandite ((Ni,Fe)9S8), heazlewoodite (Ni3S2) and awaruite (Ni2.5Fe) are the dominant nickel-bearing metallic phases and can be recovered by conventional methods (flotation, magnetic separation). Non-recoverable nickel is also present within serpentine and olivine of the silicate matrix.A detailed mineralogical program including 1420 QEMSCAN« samples and 4400 electron microprobe points was undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. A total of 105 metallurgical tests have been performed under a standard procedure which have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block-by-block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance, thus unlocking the value of the Dumont deposit and other large tonnage low-grade ultramafic nickel deposits.CITATION:Sciortino, M, Muinonen, J, Korczak, J and St-Jean, A, 2013. Geometallurgical modelling of the Dumont Deposit, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 93-100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By A J. Eggers

With gold first discovered at Carrick in 1864, exploration and mining on the Carrick Goldfield in Central Otago, New Zealand, has now been ongoing for more than 130 years. Recorded historical hard rock production from up to 52 different mining claims from 1864 to about 1921 is 24,047 ounces (oz) of gold.   Since 1980 Amoco Minerals New Zealand Limited, CRA Exploration Pty. Limited, Amax Gold Mines New Zealand Limited and Summit Gold (New Zealand) Limited have conducted modem systematic exploration campaigns targeted at locating shear controlled gold bearing quartz lodes and stockwork deposits. More than NZ $1million has been spent by these companies on aerial photography, geological mapping, stream sediment surveys, soil and rock chip geochemistry as well as reverse circulation (RC) percussion and diamond drilling.   RC drilling by Summit Resources in 1997 has identified a 1,500 m long zone of low-grade gold mineralisation at Lower Carrick, with an average grade of 1.00 g/t Au over a 14 m average thickness. This gold mineralisation, hosted within a low angle shear zone, has analogies with the Hyde-Macraes Shear Zone in eastern Otago. Recent exploration and drilling at Carrick has revealed the potential to discover large (>0.5 million ounce (Moz)) low-grade bulk shear controlled quartz vein and stockwork gold deposits similar to those now being mined at Macraes.

Jan 1, 1997

Disasters are often tragic outcomes of high-risk technologies such as mines. In Australia, more mines are being developed every day, and the risk of disasters is ever increasing. No matter how effective our conventional safety devices are, there is a form of accident that is inevitable. These relate to accidents that result from æinteracting failuresÆ in a way that could not be foreseen by the designers. In so-called ætightly coupled production systemsÆ (processes that happen very fast, such as on a high producing mine) the risk is even higher and our risk controls mostly introduce some sort of a technological fix. While we are at the one hand attempting to control the risk, we are also introducing another level of complexity. Are we really controlling the risk? This is one of the fundamental questions that will be addressed in this paper: Do we have the ability within the mining industry and other industries to effectively prevent these catastrophes, or are we, on the contrary, faced with an increasing risk as a result of increasing complexities of our technology, management systems and practices. This paper will contend that perceived improvement in risk control is an illusion of activity, and that the likelihood of mining catastrophes may be exponentially increasing. Although the paper focuses on the mining sector many aspects may be applicable across a range of industries. This paper will further contend that we are applying the right solutions to the wrong problems. Our focus is technological and procedural, while our problem is one of production cultures ripe for error and failure.

Jan 1, 1999

By N A. Sikwa, L M. van Niekerk, G N. Ndlovu

In June 2012, Lucara Diamond Corporation officially commissioned its Karowe Diamond Mine in Letlhakane, Botswana. The processing plant circuit incorporates variable speed autogeneous milling, a first for African diamond processing - only previously practiced in Russia. The paper discusses the basis for the selection of milling against the more traditional circuits incorporating crushing and scrubbing. It covers early commissioning challenges of operating a mill in an æalien environmentÆ with no immediate reference plant to look up to for bench-marking.The paper describes how these challenges were overcome and learnings quickly incorporated into the mill operating philosophy for maximum diamond liberation and minimum product damage. The plant was commissioned in three months and by August 2012 the production ramp up had reached name-plate capacity. The feed to the mill has varied from highly weathered material to extremely hard kimberlite and the operating philosophy had to be optimised for the full range of ore types. While more work is required to stretch the mill operating envelope coupled with other circuit additions to improve liberation of fine diamonds at minimum capital expenditure, the mill has, to date, performed to its billing.CITATION:van Niekerk, L M, Ndlovu, G N and Sikwa, N A, 2013. Commissioning and operating an autogeneous mill at Karowe Diamond Mine, in Proceedings MetPlant 2013 , pp 215-228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By D P. Blair

Rio Tinto’s Hope Downs Operations are currently mining iron ore in their South Central Pit. Prior to the commencement of mine operations, Hope Downs carried out an extensive archaeological investigation and identified an ancient rock shelter lying within the proposed mine boundaries. The site is significant to the traditional owners/custodians of the land in this part of the Pilbara, and thus the final pit design was changed to preserve the rock shelter, which now lies 30 m outside the mine boundary. In order to further preserve this ancient dwelling from blast-induced damage, blast design procedures were improved over time to minimise the vibration impact when blasting close to the shelter. Blasting and vibration monitoring commenced in May 2008 using pyrotechnic delay sequences and normal-direction firing. In October 2009 electronic delays were used to reverse-fire blasts close to the shelter in order to create a damage zone between the initiating holes and the rock shelter. A detailed statistical analysis of the vibration data shows a reduction in the higher levels of vibration for blasts fired after October 2009, which is most likely caused by the created damage zone. In May 2010, a site-specific vibration model was developed and implemented, and based on Monte Carlo waveform superposition. This model was used to give a further insight and improvement to the blast delay sequences when blasting close to the shelter. However, such models are expensive to implement and have limitations, which reduces their potential for estimating the probability of getting an excessive vibration due to a given blast design. In this regard, it is more realistic and significantly less expensive to use a recently developed probabilistic analysis based on simple charge weight scaling. This analysis shows that there was a higher probability of exceeding prescribed vibration limits at the rock shelter for blasts fired before October 2009 than there was for blasts fired after October 2009.

Nov 8, 2011

Study on Basic Theory of the Grain Settlement in Fluidised Bed This paper takes thick goal grains (less than 1.5 cm) as research object. According to different densities and particle sizes, thick goal grains are divided into 20 kinds of narrow density and narrow size level average grains. Free settling and hindered settling tests are respectively carried out in ?100 fluidised bed thick goal separators. Hindered settlement includes hindered settling velocity test and measurements of suspension density. Results show follows. (1) Fluid state in separator belongs to transition region. Alien's law is the appropriate formula of thick coal particles free settlement terminal velocity. (2) The main factors affecting hindered settling velocity are the number of solid particles in medium and the structure feature of the particle group. The bigger volume fractions of solids ? is, the smaller decreasing velocity coefficient of particle hindered settlement ¯ becomes. In the organism from bottom to top, density of suspended particles in fluidised bed gradually decreases, but near the top of the suspended particles, the density increased slightly. With increase of density and size, suspension density reducing extent increases from bottom to top of separators.

Sep 13, 2010

By D Wyborn, P A. Dowd

The characterisation of rock fracture networks is an important component of rock engineering applications involving stability assessment or fluid flow analysis. However, the derivation of a reliable rock fracture model remains a very challenging problem in practice. This paper describes a Bayesian framework, in the form of Markov Chain Monte Carlo (MCMC) simulation, for the construction of such a model. Model conditioning using different data sources is discussed including seismic events recorded during hydraulic fracture stimulation, rock face fracture mapping data and downhole geophysical survey data. The freeware FracSim3D is used for the simulations.

Sep 26, 2011

By M Eggers, H Baxter

This paper discusses the geotechnical condition of bedding shears and small- and large-scale faults and shears in Archean banded iron formation (BIF) bedrock, based on observations of core and televiewer images. Information that can be collected includes the orientation of defects, infill thickness, strength and material type, defect shape and surface roughness.The spacing and continuity of bedding shears may be critical to slope design where performance is structurally controlled with bedding dipping out of a wall. The intensity of development of the bedding shear is a useful indicator of the amount of shearing a bedding surface has been subjected to. This can allow for engineering judgement to be used in adopting peak or residual shear strengths along defect surfaces when developing the design.The spacing and continuity of bedding shears may also contribute to the blockiness and degradation of a rock mass where the structural orientation is otherwise favourable. Additionally the condition, thickness and strength of infill of major fault structures can affect slope design and performance, depending on orientation.Comparison of the condition of structures observed in core with the corresponding in situ televiewer image has been made to assess what characteristics are most accurately captured by each technique and whether the additional information gathered from using the televiewer technique is justified by the cost. The question of whether the data collected by a televiewer is sufficient to ultimately replace the need for core is considered.CITATION:Baxter, H and Eggers, M, 2013. Fault and shear characterisation in archean banded iron formation bedrock - a comparison between core and televiewer data collection techniques, in Proceedings Iron Ore 2013 , pp 47-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By B Mead, N D. Pascoe

The Grasberg block cave rail haulage system will be located in the Grasberg mining district on the island of Papua, Indonesia at an elevation of almost 3000 m above sea level. It will transport 160 000 t of ore per day from multiple chute galleries to the underground crushing systems. The design entails approximately 23 km of rail (ballasted and embedded track), over 120 ore chutes to deliver ore to the muck cars and three unloading stations to deliver ore to the crushers. The rail haulage system is a closed-loop system entirely within the underground mining complex.The GBC rail haulage project will be a substantial operation. Trains consist of 11–12 bottom-dump 20 m3 muck cars driven by a 40 t electric locomotive, about 400 t per trainload. Approximately 12 trains and one spare are required to maintain full production at 160 000 t/d. All rail installations will be 1435 mm (standard) gauge with AS60 steel.The rail system is designed to operate in full automated mode, including chute loading, hauling and dumping. The operation will be controlled from a surface control room.The rail haulage project has been divided into five stages, which will be brought online over the course of ten years. Current development and construction are focused on Stage 1 for initial production that will occur beginning in late 2017. This stage includes 24 chutes in three chute galleries, one unloading station, workshop areas and almost 7 km of track (3 km of embedded and 4 km of ballast).This paper describes the key components of the rail haulage system and reports on the current status of development and construction of the system. This paper also overviews the challenges, successes, issues and risks of this project in areas such as scheduling, development, construction and operation.CITATION:Pascoe, N D, Mead, B and Vega, H, 2016. Grasberg block cave haulage project – design and construction update, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 585–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

In a previous paper of this series (1) ,t it was shown that during the creep of single crystals of lead, deformation proceeded to some extent by means of slip on the octahedral plane. This was demonstrated by the formation of slip lines on the surface of the specimens. At first, a few broad bands appeared after a small amount of extension had taken place; then, as extension proceeded, more and finer lines made their appearance until the whole of the specimen surface was covered.The present paper deals with the process of deformation of the creep specimens as revealed by X-ray examination..By the use of this method, the changes taking place in the crystal structure can be observed.EXPERIMENTAL METHODThe method of preparation of the specimens, their size and the purity of the lead employed have been reported elsewhere (1). At frequent intervals, the specimens were dismantled from the test rack and X-ray back reflection photographs were taken. The specimens were so marked and set up on the X-ray machine that the same spot on the specimen surface was always examined.Copper radiation was employed, the tube voltage and current being 45 kV. and 25 m.a. respectively and the exposure time 2 hrs. The slit diameter was 1 mm.

Jan 1, 1941

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By Jardine G, Woodall C

The Henty Gold Mine, located in Western lasiuania use, uuiusatise solutions to effectively manage a mining operation in an environmentally sensitive setting and has been presented with several environmental awards. Fill is required as part of the mining method to provide passive ground support, minimise rock exposure and ensure maximum recovery of the small but high-grade orebody. The use of the whole portion of leach residue in the backfill reduces the surface tailing disposal requirements. Therefore, High Density Paste Fill (HDPF) has been selected as the most appropriate fill method to meet these objectives. Additional benefits include the minimisation of excess water from fill and the subsequent need for the collection and treatment of water and slimes. There are minimal equipment requirements during placement, thereby optimising mine resources for production. The initial paste fill design was based on the Bad Grund and Ranunelsberg Mines paste fill systems of Preussag in Germany and comprised pumping filtered tailings paste some 1.2 kin uphill from the mill to the mine portal, where cement was to be added before being distributed underground. The system was designed following initial testwork that was undertaken on a bulk sample of ore mined from the scar surface Sill Zone. Subsequently, during the mining of the Zone 96 orehody, it was found that there were significant mineralogical variations in the composition of the ore mined. Following processing, the resultant Icach residue caused significant changes in the paste rheology and therefore the pump and flow characteristics. An alternative solution was implemented that involved the use of agitator trucks to transport the cemented paste to the portal. This required modifications to the fill preparation system and also the underground distribution system. Laboratory strength tests of the HDPF using actual gold plant leach residue showed low early strengths were attained with HDPF containing only filtered leach residue. Therefore, high binder addition rates or an increase in the fill cycle time would be required to allow the fill to gain sufficient strength. A considerable amount of potentially acid generating waste rock also requires underground disposal. By blending the waste rock with the HDPF, the strengths were improved and the required cement addition rate reduced by about one-half. The potentially acid funning waste rock is encapsulated in the highly alkaline cemented paste, minimising the potential for acid generation.

Jan 1, 1998

INTRODUCTION ò World coal production, Exporters and Importers òNew Zealand Exports, Markets and Products ò Types of Markets and Price Setting ò Bench Mark Prices and Exchange Rate ò Transport ò International Marketing - Key Factors ò Coal New Zealand , the Challenges

Jan 1, 1996

Plant for the production of sulphuric acid from pyrites flotation concentrates was commissioned at Cockle Creek during 1956, to meet increasing demands for commercial acid and superphosphate. Pyrite was chosen as raw material because of the uncertain supplyposition of imported brimstone and the desirability of utilising domestic sulphur.Desulphurisation of the pyrite is performed by two 40-ton per day roasters of the Turbulent Layer type operated under licence from the Badische Analin and Soda Fabrik (B.A.S.F.) organisation. These units are the first of their kind commissioned in the southernhemisphere. Pyrite is fed to the roasters in the as-received un-dried condition. Waste heat steam production is coupled with electricity generation within the plant. Sulphur dioxide is produced at comparatively high strengths and cleaned by conventional cyclone and hot electro-filter equipment.The acid unit has a capacity of 100 mono tons of sulphuric acid per day and includes cooling and wash towers, mist precipitators, a single stage drying tower, 4-pass oxidation section and absorption system.INTRODUCTIONSulphuric acid has been manufactured at Cockle Creek Works since 1913, when the first chamber nitration plant was commissioned. The raw material was brimstone roasted in Herreschoff furnaces. Since that time three additional chamber units have been constructed and have produced acid from brimstone, zinc concentrates, pyrites and -spent oxide, according to changing economic and supply factors.Three chamber units are still in operation. Contact processes have become increasingly important since the first Schroder-Grillo unit was commissioned in 1923. Six of these 5-ton per day units were operating in the mid-thirties, but have since been demolished. Two 15 ton Chemico hot gas contact units commenced operation in 1937 and 1938, and although modified, are still in service.The increasing demand over recent years for sulphuric...

Jan 1, 1957

Minerals processing needs a step change in energy efficiency. While the search for new technology breakthroughs is important, huge gains are still available by better using existing research outcomes. This potential remains untapped due to a combination of organisational &apos;silos&apos;, inappropriate performance measurement, and poor science in some areas. It is time to see the elephant in the mill.

Sep 13, 2010

Magnetic anomalies in the Southern Coalfields have been subdivided into two characteristic types. Each type is attributed to a separate cause, one being basement structure, and the other near-surface igneous intrusions.Detailed geological mapping of the area and the ability to sample throughout the coalmines greatly assisted in this subdivision.The Triassic sequence contributes no magnetic effect of its own except to diminish the effect of sources within the underlying formations by raising the level of observation.Detecting the presence of igneous intrusions ahead of colliery working faces by magnetic observations within the coal mines may be of value in preventing accidents caused by gas outbursts and in planning the workings so as to avoid loss of production time.

Jan 1, 1967

Soon after the Rosebery concentrator commenced operations in 1936, an investigation was begun in an attempt to discover a substitute for cyanide in lead flotation. Cyanide is an excellent depressant for zinc and iron, but it also powerfully depresses the copper, silver and gold bearing minerals present in Rosebery ore, thus allowing them to pass through to the zinc concentrate or final residue where they are of little or no value.The investigation was not entirely successful, but it did indicate that sodium bisulphite or sodium sulphite could be used as a depressant for zinc without depressing the copper, silver and gold bearing minerals. The sulphites were, however, much inferior to cyanide as apyrite depressant.At about this time, I. W. Wark, using the captive bubble technique, had shown that, at the concentrations normally used, sodium aerofloat is not a promoter for pyrite or galena in alkaline solutions (see his book &quot;Principles of Flotation&quot;, p. 188). Some preliminary tests on the production of a copper concentrate from Rosebery ore were therefore carried out using sodium sulphite as depressant and sodium aerofloat as promoter.The results of this work were promising but, since Rosebery ore usually carries only about 0&#183;5% copper, there did not seem to be much incentive to carry the work further. With the outbreak of war, however, Australia became desperately short of copper and the relatively small amount in the ore. became of sufficient importance to...

Jan 1, 1952

By J Ward, B Rohrlach, B Rosero, J Silva, O Poma

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Alpala copper-gold deposit is a recent, high-grade porphyry Cu-Au discovery located in the Imbabura Province of north-western Ecuador. The deposit lies along the crustal-scale Chimbo-Toachi Fault Zone within the Dagua-Piñon terrane, which is an oceanic plateau accreted to the South American convergent margin in the Late Cretaceous. The deposit is hosted by quartz diorite stocks that intrude andesitic volcanic breccias of the Oligocene to mid-Miocene San Juan de Lachas Formation. Miocene-age calc-alkaline plutonism is associated with porphyry Cu, Cu-Mo and Cu-Au deposits in southern and northern Ecuador. The Alpala deposit lies along a sector of the Miocene arc that has recently been underplated by the Carnegie Ridge seamount chain that induced shoaling of the subducted Nazca plate beneath northern Ecuador.Surface expressions of the deposit were recognised in May 2012 during follow-up of stream sediment anomalies, when outcropping sheeted and stockwork porphyry-related veins were discovered in Quebrada Alpala. The roots of a NW-trending, structurally-controlled lithocap were recognised over an area of 4.5 × 0.9 km. The remnant lithocap exhibits well-defined mineral zonation mapped by TerraSpecTM analyses on grid soil samples. Soil sampling, heliborne magnetic surveying and channel sampling defined initial drill targets.Seven diamond drill holes were completed in the year from September 2013. Drill hole CSD-13-005 intersected 672 m grading 0.93 per cent Cu and 0.91 g/t Au in high-temperature, inner propylitic and locally potassic-altered quartz diorite intrusions. Overlying hydrothermal clay alteration assemblages define the base of the lithocap. A NW–SE trending footwall structure defines the south-west margin of the deposit. Drill hole 5 intersected high-grade sheeted ‘B-type’ and ‘C-type’ veins (Gustafson and Hunt, 1975) that lie along the south-west margin of an 1100 × 500 m magnetic anomaly that is the focus of ongoing exploration.CITATION:Rohrlach, B, Poma, O, Rosero, B, Silva, J and Ward, J, 2015. High-grade porphyry copper-gold mineralisation in north-west Ecuador – The Alpala Cu-Au porphyry discovery , in Proceedings PACRIM 2015 Congress, pp 369–376 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By P Revell, G Wilkie, P Walters, L Keeney, F Faramarzi

Grade Engineering® is a value-driven strategy aiming to maximise benefits by exploiting intrinsic grade variability of ore deposits. It utilises a multitude of separation techniques to remove low grade material before being introduced to post-blast size reduction processes, i.e. crushing and grinding. At an operational scale, Grade Engineering® techniques can be implemented at the drill-and-blast stage, to control the degree of fragmentation in accordance with the spatial distribution of valuable minerals across an ore domain through differential blasting. It can also exploit intrinsic textural and breakage characteristics of a given ore type to reject uneconomical barren material at coarse sizes, which is known as Natural Deportment. Grade Engineering® can also be employed in the deliver stage of the mining value chain through sensor-based bulk and particle sorting. Each strategy is therefore highly dependent on the responsiveness of an orebody to available techniques. That is, the extent to which Grade Engineering® drivers would be capable of unlocking potential values of currently un-amenable orebodies depends on how detailed the heterogeneous nature of ore domains can be described. This paper considers exploring possible linkages between deportment characteristics of an ore and its competence when broken in a range of energy inputs at a particlebased level. Accordingly, potential opportunity may lie in exploring whether the intensity of input energy (or degree of fineness) can be used as a lever to improve or ‘unlock’ ore amenability to Grade Engineering® techniques. Implications from such a detailed approach offers new opportunities to enhance Grade Engineering® gains through engineering ore competence variability.

Nov 10, 2020