Search Documents

Access roads for haulage, construction or maintenance purposes are discussed with particular attention being given to the un- sealed "all weather" form of construction for Off-Highway applications. The service conditions experienced by the surfaces used in these roads is examined. These conditions are discussed in terms of the conventional engineering properties used for natural gravel material selection. Experience gained during the construction of a pipeline access track is used to illustratE material selection guidelines based on geological input and an understanding of good construction practices. TMITDnIll IrTT Ohl In many Australian situations off-highway haulage by wheel or track supported vehicles is carried on unsealed, gravel roads. Although the unsealed gravel road is the back-bone of the rural road network in Australia, in general, traffic loadings are relatively low compared to the off-highway unsealed haulage road. The cost of the haulage/access road construction component is one important factor in project planning which needs careful consideration. It is no longer acceptable that the initial rough exploration track be gradually upgraded so that it will eventually carry construction and maintenance traffic safely and efficiently. Fatal accidents and

Jan 1, 1982

The excavation of a tunnel through rock and mixed ground of basalt and silty clays presents a challenge to engineering organisations. Such was the situation facing the Melbourne and Metropolitan Board of Works (MMBW) in constructing the 15.3 km, 5.5m dia. tunnel component of the new Western Trunk Sewerage System. The tunnel geology showed that there were two distinct components to the excavation - rock and mixed ground. By drawing on extensive experience in the use of Tunnel Boring Machines (TBM's) used previously by the MMBW and using techniques developed for predicting TBM per- formance, a comparison of the options of drill and blast versus TBM was made. The conclusion was that TBM methods would provide the best solution to the problem. Tenders were called for the supply of a TBM. A performance specification was used to attract tenders offering designs which re- flected the state of the art on an internation- al level. Particular features required by the MMBW were included in the specification. The excavation planning and operation are described in this paper. The production achieved has shown that the TBM can very adequately handle rock excavation (best weekly production 167.9m). Extreme conditions of mixed ground with heavy groundwater inflows have been handled using an auxiliary thrust system to maintain gripper reaction through the soft ground encountered.

Jan 1, 1987

By X Hu, C-C Yang, J Pan

In this work, preheating and roasting tests of pellets made from blends of Western Australia ultra-fine (WAU) magnetite concentrate and Chinese domestic magnetite concentrate or Brazilian hematite concentrate were carried out. The results showed that pellets made from 100 per cent WAU magnetite concentrate possesses inferior preheating and roasting performance when preheating at 1050°C for 20 minutes and roasting at 1300°C for 40 minutes, the compressive strength of preheated and fired pellets is 502 N/pellet and 2313 N/pellet, respectively. When 40 per cent Chinese domestic magnetite concentrate or 20 per cent Brazilian hematite concentrate was blended with 60 per cent or 80 per cent WAU magnetite concentrate, the appropriate preheating temperature of the pellets are reduced from 1050°C to 950°C and 975°C, and also the firing temperature of two types pellets are decreased from 1300°C to 1250°C and 1280°C respectively. Moreover, the compressive strength of fired pellets is obviously improved up to 2746 N/pellet and 2630 N/pellet respectively. Microstructure analysis of the fired pellets made from 100 per cent WAU shows its poor growth of Fe2O3 grains, low interlinkage degree of hematite grains, small size of crystallised grains and high porosity of pellet; however, the fired pellets that blended with domestic magnetite concentrate or with Brazilian hematite concentrate have fully growth of Fe2O3 grains, closer interlinkage of hematite grains, lower porosity and stronger consolidation. The preheating and roasting performance of WAU magnetite concentrate pellets can be improved by optimising ore matching.CITATION:Pan, J, Hu, X, Zhu, D-Q and Yang, C-C, 2017. Pelletising performance of Western Australian ultra-fine magnetite concentrate and strengthening technique by optimising ore matching, in Proceedings Iron Ore 2017, pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By S Lehane, S Pearce

The characterisation and assessment of waste rock has been the subject of considerable research, and many guidance documents have been published both internationally and within Australia. While these documents provide detailed information on how to characterise waste rock, there is not a great amount of detail on how to determine the optimal waste management options from an operational viewpoint. For example, typical questions that a mine operator would seek answers to include: What placement method should be used (eg end tipping versus paddock dumping)? What is an optimal tip head height for waste placement in a storage facility? How should sulfide grade control be carried out?Defining the contributing factors to waste management and waste material placement and assessing the contribution of each variable directs these assessments towards a semi-qualitative and quantitative methodology. Quantitative methodologies show an increase in the confidence of these assessments by providing logical, measureable assessments.As part of a strategic assessment for waste management at an active mine site, a detailed risk-based investigation of the influence of variables common to waste placement was completed. These variables included placement method, placement height, sulfur grade and material conditioning (eg compaction) on the associated risks of waste material storage. The assessed risks include temperature assessments (potential for thermal take-off as a result of spontaneous combustion), toxic gas production and flow and acid production potential. Applying a numerical modelling approach to the assessment of the different waste material placement strategies allows for the variation in risk to be graphically presented and communicated through risk matrices and histograms.CITATION:Pearce, S and Lehane, S, 2015. Quantitative risk assessment tools to assist with waste management and placement guidelines, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 353–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

The purpose of this paper is to look at the costs of tailings disposal, and in particular the comparative costs of different disposal methods in different situations. Costs are often the hidden design parameter. We know that they are important but sometimes feel that it is not very respectable to talk about them in public. It is better from a public relations point of view for it to appear that the decision-making process is driven by environmental factors or best practice rather than looking for the cheapest option. But this presumes that the two are mutually exclusive and this need not be so. These issues are discussed later in the paper. It is also commonplace for the scale of the mining operation to change with time, typically involving increased throughput rates and total tonnage. New ideas in tailings disposal make their appearance. The regulatory attitude can change. Having made a decision about the disposal method at the time of original feasibility study and design it is easy to suppose that the mine is æstuck with itÆ. But that also need not necessarily be so. Careful costing of options may reveal that a switch in method could be cheaper in the long run. The designer will often tend to think in terms of initial earthworks and site development costs. Aspects of power consumption, labour, and periodic campaigns to move tailings pipelines and carry out embankment raises are either overlooked or not given the same emphasis. This can distort the evaluation process. It is productive to think in terms of dollars or cents per tonne as a basis of comparison, not just the total sums. Tailings disposal can cost from as little as 10 - 20 ó/t to over $1.00/t which is a big range. There may be good and unavoidable reasons for the high figure but there would need to be to justify being so far over the industry average. At the same time, mining and processing costs, at least for gold, are around $15 - 20/t. Viewed from this perspective tailings disposal will always be a relatively small component of the annual budget.

Jan 1, 2000

By A Rantala, K Aberkrom, O Haavisto, P Blanz

More complex ore bodies with lowering grades increase the challenges of maintaining high throughput, energy efficiency and required particle size for optimal downstream processing in grinding circuits. Continuous and often rapidly changing characteristics of the mill feed requires constant focus to operate the circuit at optimal level. Modern process instruments, on-line analyzers, monitoring and process control systems provide attractive and managed options to increase the circuits’ capability to respond to the challenge, often in phases and in rather short time period. Furthermore, well instrumented and performing base level automation in the grinding circuit enables advanced process control (APC) strategies that utilize measurements from the whole circuit to stabilize and optimize production. In this paper alternatives for incorporating process measurements and controls to typical grinding circuits are proposed. The expected benefits to throughput, availability, energy efficiency and particle size stability are described in recent case examples.CITATION:Rantala, A, Blanz, P, Aberkrom, K and Haavisto, O, 2015. Increasing grinding circuit robustness with advanced process control, in Proceedings MetPlant 2015, pp 129–141 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By S Matos Camacho, K G. van den Boogaart, R Tolosana Delgado, U Mueller

"The precise formulation of a geometallurgical optimisation problem is by necessity a simplification of reality. It includes implicit choices such as data availability or mining block geometry. Additional data can be orebody data, production data or market data. Often these choices are predetermined by the software, the workflow or the corporate culture, and as such are not even queried. There are several aspects that might play a role in the optimisation. They include not only the spatial model on which the selection of mining blocks and the potential mining sequence are based, but also the complexity of the processing model, the way in which uncertainty is treated, the scope of responsibility and the complexity of the model. In addition the timing of the optimisation and the availability (or lack thereof) of information will influence the outcome of any optimisation.We show that different modelling choices and different model formulations for the same mine can lead to very different processing choices, substantially different net present values (NPV), opposite investment decisions and so to overall different values for the entire operation. The selection of adequate simplifications and corresponding formulations for the optimisation problem is thus an important task in itself.For this purpose we introduce a method for quantifying the impact of certain simplifications prior to the optimisation. For example, the effect of mining block choices depends mainly on the spatial structure and the structure of the processing gain function. Both can be quantified beforehand. Based on the outcome, appropriate simplifications can be selected for the geometallurgical optimisation.CITATION:van den Boogaart, K G, Tolosana Delgado, R, Mueller, U and Matos Camacho, S, 2016. How Details of the Geometallurgical Optimisation Influence Overall Value, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 303–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By C Bonini, A Markham, P Whittle, B Pearson

"Mine-derived sedimentation in rivers can have significant impacts on the processes and features of the receiving environment and impact on communities reliant on this environment. However, identifying and quantifying the contribution of mine-derived sediment to the receiving environment can be complex. This is particularly the case in remote environments and where little/no baseline assessments have been undertaken. One approach that can be used involves sediment fingerprinting, whereby a unique tracer is identified within the mine-derived sediment to discriminate between mine- and non-mine derived sediment sources downstream. The technique typically involves sampling of sediment at upstream, control and impact sites and sites within the mine deposit. Laboratory analyses are run on all the samples to determine whether the chemical signature (eg presence/concentration of specific metals) differs between each group of samples. In complex environments where the mine-derived signature may be difficult to detect from a basic review of the data, or where sampling constraints may limit the number of samples for analyses, statistical methods can be used to help identify sediment groups. This paper provides a mine case study to show how such an assessment can be undertaken despite the logistical challenges faced while working in remote environments.CITATION:Pearson, B, Markham, A, Bonini, C and Whittle, P, 2013. Fingerprinting and signatures - tracing mine impacts in complex aquatic systems, in Proceedings Water in Mining 2013, pp 287-292 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

During October 1947 an Authority to Prospect was granted by the Minister of Mines to lVIount Isa Mines Limited over an area of approximately 75 sq. miles to the north of Mount Isa.Application for the Authority to Prospect had been made after Zinc Corporation Limited had been granted prospecting rights over two areas, one of 1,265 acres immediately to the north of the Mount Isa Mines leases and the other of 1,960 acres adjoining the south end of Mount Isa Mines leases.METHODSAs a means of providing a cheap map of sufficient accuracy on which to plot geological features, both Mount Isa Mines Limited and Zinc Corporation Limited agreed upon aerial photographs and the two companies shared the cost of an aerial photographic survey by Adastra Airways of 130 sq. miles which covered the prospecting areas held by both companies.The photographs were on a scale of 800 ft. to I in. with 60% overlap on the north-south runs and 25% overlap east-west. A set of alternate prints enlarged to 400 ft. to 1 \in. were obtained for field work. The 400 ft. to 1 in. scale unglossed photographs (size 18 in. x 18 in.) were taken On to the field and rock outcrops, and uncorrelated structures were plotted directly on to them in red crayon pencil. The geological observations were then transferred in the office to a tracing on which accuracy of azimuth and scale was controlled by use of a photo mosaic and ground surveys.

Jan 1, 1953

By K L. Avarmaa, M A. Rhamdhani, A D. P Putera, H T. B M Petrus, G A. Brooks

Multistage slag treatment was carried out to investigate boron removal from metallurgical grade silicon. Boron is known to be one of the most difficult elements to remove from silicon. Depending on boron initial concentration, boron can be removed from silicon into certain level; most previous studies have attained final 50–100 ppmw (parts per million weight) boron in the silicon using slag treatment. The term ‘multistage’ refers to a process where the resulting silicon from the initial slag treatment is further refined multiple times using a new slag. In this study, an initial slag composition of 45CaO-45SiO2-10Al2O3 (wt per cent) was utilised. Using this technique, boron level in the silicon was expected to be gradually lowered because the new slag will always have more capacity to reach the equilibrium distribution coefficient (LB = (ppmwB)slag/(ppmwB)Si). The current study was carried out through combined thermodynamic calculations (using FactSage™ ver 8.2, by Thermfact Ltd, thermochemical package) and high-temperature experimentation. The thermodynamic calculations were carried out for reactions at 1500, 1550, and 1600°C for three different scenarios: 1. Single stage refining with varied slag to Si ratio. 2. Multistage refining with slag to Si ratio of 1:1. 3. Multistage refining with slag to Si ratio of 2:1. The multistage experimental work was carried out at 1550°C under inert gas atmosphere each time for 2 hrs, with slag to Si ratio of 2:1. The simulation results indicate that the boron distribution coefficient stay essentially constant with varying slag to Si ratio and temperature, around 1.8 to 2, and the experimental results measured LB in the same range, between 1.5 and 2.5. By harnessing this feature, the simulation showed that boron can be removed by approximately 78 per cent in each stage. The experimental result confirmed that the boron concentration in the silicon was reduced by a total of 97.8 per cent from its initial value using four stages of slag treatment, from initial 270 ppmw down to 6 ppmw.

Aug 21, 2024

By M Lak, R Amiri, A Haratian, M Asghari, S Haji

Dry magnet separators are used to upgrade and beneficiate a wide variety of minerals such as hematite and magnetite materials. In recent years advances in dry magnetic separators have improved their performance. Fine particle separation is one of the main areas which still remain weak. This paper will present a new design of fine particle drum separators which used for particle size less than 3 mm. A big problem in processing of iron ore is the grade and recovery of mineral values in the fines fraction. The new design high efficiency drum separator is developed to handle fine feeds. In this drum separators both of the drum shell and magnetic yoke rotate in opposite direction. the results showed that when the material feed size was = 1298 μm, drum shell speed was 42.5 rev/min, magnetic yoke speed was 100 rev/min and the maximum intensity of magnetic field was at = 30° the feed grade increased from 50.87 to 65.67 in concentrate box, increase to 60.45 in middle box and tail grade was 24.44. The total achieved recovery for both concentrate and middle box was 81.89 per cent.

Nov 8, 2021

Experimental Validation of a Flotation Cell Model

Sep 13, 2010

By L Keeney

Geometallurgy is not a mechanism designed to replace current geological and metallurgical deposit characterisation but an added component required to understand orebody variability. Current geological characterisation approaches focus on understanding deposit genesis aimed at identifying new mineralised regions and metallurgical characterisation determines parameters required for engineering design of processing plants. Geometallurgical integration has the task of drawing on aspects of each stream to enable spatial mapping of performance indices across a deposit. It is a complimentary activity to current practice and adds a new dimension to orebody knowledge. Although the notion of conducting an integrated geological and metallurgical analysis is not a new concept, limited publications exist in the field proposing integrated methods, with several technical issues existing in current geometallurgical integration approaches. An iterative method drawing on existing geological and metallurgical characterisation and new measurement tools and inputs is proposed. The integrated method comprises of discrete components dynamically linked together through iterative feedback loops with each component having a specific purpose achieved by applying a range of data acquisition technologies and statistical tests. The key outcomes of the method are:overcoming the lack of optimised geometallurgical domains relevant to processing performance,development of a rigorous approach to identifying parameters controlling processability,improved protocols for relevant metallurgical test data and sample selection, andability to generate greater data support to enable rigorous geostatistical modelling of geometallurgical attributes. This paper outlines the integrated mapping and modelling method developed and draws on multiple data acquisition technologies applied within the AMIRA P843 GeMIII Project.

Sep 5, 2011

By L Manca, P B. Hills, D Tyler, N Pollington

This paper describes a collaborative project undertaken by Newcrest Mining Limited (Newcrest) and pitt&sherry to identify, develop and then implement global best practices to manage the exposure to inrush (dry and mud) hazards in underground mining operations. An extensive literature review was undertaken to identify past experience globally and the current state of knowledge and practice in managing inrush hazard. A key requirement of the literature review was the development of a list of guiding questions which would form a framework for approaching operators to discuss the topic, capture recent learnings and understand current operating practices to allow the development of a best practice solution. An initial cohort of 14 mines across four continents chose to contribute and detailed interviews were carried out by the project team. The outcome from the literature review, interviews with participating mines and various internal discussions was a comprehensive summary document detailing Basic versus Best Practice management of the inrush hazard. This document is being used as a gap analysis tool by Newcrest to assess and guide the management of inrush hazard at their existing and future operations. The summary document has also been provided to the participating mines for their consideration. The project is iterative and will continue to evolve as new experiences, knowledge and practices come to light.

Mar 15, 2021

By S G. Keyte

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.l mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass Yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80 per cent and mass yields of less than one per cent can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

Various methods and software have been trialled for simulation of Au grades at Boddington Mine. This covers in-house and public software as well as sequential and turning bands methods. The diversity of options was further expanded with comparison of point and direct block simulation. Some difficulties were encountered in incorporating high-grade restrictions. Altering parameters or software can make very significant differences and give results varying from estimations. This paper details a new simulation run with validation and tests for local calibration (or progressive correction) of the simulations to the estimations, focusing on reproduction of statistics. This approach brings to the forefront the question æwhat is the purpose of the simulations?Æ Results and some ideas for future applications at Boddington are summarised.

Sep 26, 2011

By R C. Morris

Two major types of economic secondary iron ores occur in the banded iron formation (BIF)-rich Hamersley Province of the Pilbara, Western Australia:dominant BIF-hosted bedded iron deposits (BID)detrital ore deposits (DID sensu lato), which are mainly hosted in the three province-wide Cenozoic sequences that include coeval non-ore sediments and comprise:a. the major Miocene, fluvial channel iron deposits (CID)b. the lesser Eocene and Pliocene detrital iron deposits (DID sensu stricto).Striking differences exist between the massive CID resources and the much smaller underlying and overlying DID. CID are essentially riverine alluvial ooidal rocks with abundant small fossil wood fragments and variable iron peloids, but with only extremely rare recognisable lithic remnants. The original matrix is typically ramifying layered goethite. Eocene DID are mainly alluvial with minor pisoids, whereas Pliocene–Quaternary DID are dominantly coarse colluvial gravels, both derived from and largely retaining the original textures of BID, hard cap or variably ferruginised surface BIF. The colluvial DID matrix is typically ferroan-aluminous soil, resulting in canga where replaced by goethite, which may be dehydrated to hematite by exposure. The Cenozoic deposits occur in two dominant geomorphological environments: the southern Marra Mamba to Brockman Iron Formation strike valleys containing all three Cenozoic sequences and the much later northern Brockman Iron Formation plateau valleys that include only the Miocene and Pliocene sequences. The Cenozoic detritals formed in different climatic regimes, with an extended dry period forming a prominent province-wide dehydrated carapace on the Eocene DID. The Miocene ‘optimum’ followed with its thick scrub-covered deep regolith that produced the fossil wood-rich CID and was succeeded by the arid cool period of the Oakover limestone/calcrete. A major renewal of exposure and erosion in the Pliocene resulted in the extensive iron gravels of the Pliocene–Quaternary.CITATION:Morris, R C, 2015. The Cenozoic detrital iron deposits of the Hamersley Province of Western Australia – a tribute to Mal Kneeshaw, in Proceedings Iron Ore 2015, pp 319–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A B. Christie, R L. Brathwaite

Since the first occupation of New Zealand in 800 - 900 AD, various useful minerals, rocks, and energy resources have been identified and extracted. The Maori prized greenstone for ornaments, tools, and weapons, used argillite and obsidian for tools, and decorated their carvings and bodies with colours made from clays, limonite, and vivianite. They were aware of coal (waro), but are not known to have used it for fuel. Before 1840, visiting whalers used coal from Shag Point to heat their trypots. Mining activities got underway in the 1840s, with the finding of manganese oxide deposits in the Bay of Islands, Kawau Island, Waiheke+ Island, and Taieri Mouth. Secondary copper ore was mined on Kawau Island (1846 - 1869), and native sulphur was exported from White Island to Europe. The discovery of gold at Coromandel in 1852 and a few years later in Northwest Nelson and Otago opened the way to gold rushes in these areas and subsequently in Marlborough and Westland. Mining of alluvial gold evolved through sluicing to the invention of gold dredges; first (1863) was the simple spoon design, but later (1881) large steam-powered bucket-ladder machines weighing around 3800 tonnes were built. Most of the gold dredges had gone by the early 1960s, following a revival in the 1930s, but one large dredge operates today on the Grey River. Other mining events included: underground mining of coal from 1849 and underground mining of lode gold from 1863 in the Coromandel, Reefton, and Otago fields. Most outcropping coal deposits had been discovered by 1870. Building stones were used by the early settlers for construction of houses, churches, banks, public buildings, and some universities from 1836. Aggregate for roads, railway ballast, and concrete, and limestone for cement and fertiliser, and clays for bricks and china have been quarried for many years.

Jan 1, 1993

By G T. Kukla

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland û Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground subsection of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes operational. Support of the site's system continues from head office which is continually involved in development of SUMPS and issuing revision updates to sites. The users, as well as programmers, were mostly geologists and mining engineers. This helped to ensure rapid, successful implementation. The broad approach of this system was to use interactively the specialist skills and interpretative abilities of the user mining engineers and geologists with the data manipulation abilities of the computer. It is an integrated system which covers geological exploration, deposit modelling, mine planning and production scheduling. An important feature of the system is that the user has full interactive control over each function through a graphics terminal where applicable.

Jan 1, 1980

By R Jaine, D Strang, M Fowler

"This paper presents a case study demonstrating active geotechnical pit slope management at the now completed Carina Iron Ore Project operated by Mineral Resources Ltd (MRL). The site is located 105 km north-east of Southern Cross, Western Australia. The paper is primarily focused on the slope stability failure modes and the remedial measures employed to maintain mining.Between a quarter and a third of the excavated slopes were impacted by some form of instability that was beyond expectations of the intended slope design criteria and common practice. Ongoing mining was supported by intensive geotechnical pit slope management including close cooperation between geotechnical, mine planning and operations staff to achieve timely and practical mining solutions.Mining encountered varied slope failure mechanisms which required a combination of remedial solutions comprising: horizontal depressurisation holes, deferral of excavation, unloading, buttressing and catch berms.The root cause of the challenging slope performance was a mismatch between the predicted and encountered geotechnical model, resulting from a failure to recognise the critical mechanisms that control slope stability.Despite the extensive zones of instabilities at completion of mining, full ore recovery was achieved without major delays and in a controlled and safe manner.Citation:Fowler, M, Strang, D and Jaine, R, 2016. Adapting to Geotechnical Change - a Case Study of the Carina Open Pit Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016