Search Documents

By R Barritt, P Scott

Across the globe, it is a common scenario that tailings storage facilities (TSFs) are being decommissioned; however, their subsequent impact on the local environment and landscape can often be overlooked during the mine planning process. In addition, the requirement of a cover system for a facilities closure may not be a priority until the latter stages of the mine/mill operation when potential cover materials may have been utilised elsewhere or, worse, buried. Developing a conceptual design and closure plan for a TSF early in a mining venture is fundamental to its success once operations have ceased. If a cover system is a planned component for rehabilitation of a TSF, it is vital that its design is appropriate to the facility and any local site constraints, such as climate and cover system material availability. It is also strongly recommended that various cover system options are physically trialled at the site by using performance-monitoring instrumentation. Through this process, an informed decision can be made regarding the most appropriate cover system design to meet any regulatory and stakeholder closure objectives and criteria specific to the site in question; however, in order for the cover system’s performance to be determined through on-site trials, it is essential that an appropriate instrumentation design is utilised. Often, little attention is paid to the data that is being obtained, and its importance may only become apparent after several years of monitoring at an expense to the venture. This should not be the case. Many sites have used an appropriate initial planning stage to understand what is required for the successful closure of a TSF, how it can be achieved and how monitoring data can be utilised to prove, or otherwise, that a cover system design will be a success.CITATION:Barritt, R and Scott, P, 2015. Cover system performance monitoring for tailings – are we doing it correctly?, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Munro P. D

Eh-pH measurements were taken on an industrial zinc reverse flotation process at Brunswick Mining and Smelting Corporation Limited. Laboratory zinc reverse flotation testwork on samples of the feed to the industrial process produced Eh-pH data which were similar to the data from the industrial process.Later, the Eh-pH data from the industrial process were compared with data from a pilot plant scale zinc reverse flotation process at Mount Isa Mines Limited. After comparison with the data from Brunswick Mining and Smelting Corporation, deficiencies in the pilot plant Eh-pH data could be recognised and corrective actions were taken for the pilot plant. A robust pilot plant zinc reverse flotation process was obtained with consistent performance at the expected level.The implications of these findings for a range of processes are also discussed.

Jan 1, 1988

By D Craw, P Upton

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Otago Schist belt of southern New Zealand hosts widespread orogenic gold deposits. Erosion of these orogenic gold deposits has led to the formation of numerous placer deposits distributed across and beyond the host schist belt. Numerical modelling of crustal scale deformation and geomorphic evolution has defined the key tectonic features that have controlled the severance of detrital gold deposits from their sources. Tectonic activity over the past 20 million years, during development of the modern Pacific-Australian plate boundary, has severed links between some placers and their sources. Detrital gold was transported south from the Otago Schist source region in two different river systems in the Miocene. Mesozoic orogenic gold deposits shed gold into rivers that flowed to the south. These rivers were terminated by the rise of north-west-trending basement ridges at the boundary between weak schist crust and strong greywacke crust, and the ridges were controlled by pre-existing faults at that rheological boundary. In contrast, rising mountains close to the developing plate boundary in the Miocene were the locus of new orogenic gold deposits hosted in extensional faults. These gold deposits were rapidly exhumed and contributed detrital gold to orogen-parallel Miocene rivers that flowed to the south-west. Pleistocene deformation on mainly north-west and north-east orientations, and associated river capture, has severed the links between these Miocene orogenic deposits and downstream detrital gold.CITATION:Craw, D and Upton, P, 2015. Tectonic severance of links between placer gold and its sources, southern New Zealand , in Proceedings PACRIM 2015 Congress, pp 541–544 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

This paper reviews the gold mining history and recent exploration activities on a number of beaches in the Catlins area of coastal South Otago. Past mining history and recent sampling indicate the presence of economically significant concentrations of placer gold, as well as anomalous PGM, and various heavy mineral species. A local source for this placer mineralisation is considered a strong possibility, along with a contribution from the Waiau River catchment via longshore drift. Blacksand beds in Jurassic sandstones of the Southland Synclinorium may represent this local source of mineralisation on the modern beaches. The possibility of placer mineralisation extending onto the inner continental shelf is also considered. Further exploratory work is justified, both for in situ Jurassic blacksand deposits, and to delineate mineralisation in the modern beach and inner shelf environment.

Jan 1, 1992

By C Sylvestre

For the last 50 years, traditional safety management has improved safety performance by: • Fixing the environment (eliminating the hazard). • Improving the system (more/less rules, procedures etc). • Making safety more conscious (more/better interactions about the importance of safety). Although these approaches certainly have merit, and may be part of an overall solution, they are not enough to prevent many modern-day incidents. Today, these three approaches are used more than before, and are used better than ever before. Yet, workplace fatalities in Australia have stagnated from 2013 to 2019, as have the number of incidents, even serious ones. In the USA, workplace fatalities have increased by 15 per cent in the same period.

May 5, 2022

The transition from exploration to feasibility is a stage in the development of mineral resource projects that is frequently not handled well. The transition marks a point in the project development process where resource evaluation priorities change significantly from the discovery of mineralisation and the rapid assessment of the potential tenor of the mineralised system, to the detailed assessment of the deposit.   Information used in the exploration process tends to be of a qualitative or theoretical nature initially, but gradually becomes more quantitative in character as geological knowledge relating to individual prospects grows.   The transition from discovery and rapid exploration of a new deposit occurs at a relatively early stage in project development, coinciding with the first attempt to prepare a resource estimate for the deposit. Fundamental assumptions regarding both structural and grade continuity and uncertainty inherent in existing information need to be made so that they themselves may be addressed during the collection of additional data.   The effective commencement of feasibility studies involve the introduction of new accountabilities either as a result of appointment of a project manager, and through needing to be able to quantify: ò     the quality of data being collected for resource evaluation purposes; ò     confidence associated with resource estimates; and ò     the need to develop an audit trail for the project, required to make the resource evaluation decision-making process as transparent as possible.   Quality assurance is a concept to which exploration geologists have frequently had little exposure. Being able to demonstrate the quality of data used in feasibility studies is, however, a crucial component of the overall risk management and reduction.   Development of a transparent audit trail for data assists in demonstrating the quality of data which is frequently perceived to translate directly to confidence inherent in resource estimates.   Establishing procedures for geological data collection and management also provides a more reliable framework for making decisions that impact on project execution, again resulting in improved confidence in resource estimates and associated geoscientific data.   Regular, independent technical audits, in principle similar to audits conducted for the ongoing certification of standards compliant quality assurance systems, are a major, positive factor in effective project management and execution.   Information used in project evaluation, feasibility and development must be based on facts. Facts are effectively observations that are ideally made systematically, recorded in a systematic manner, and by being collected effectively are not subject to change.   Effectively managing the transition from exploration to resource evaluation, feasibility and project development involves recognising the nature of changes in the nature, detail and scope of geoscientific data required at each stage of project development. In doing so it is essential to: ò     recognise when the change occurs (as early as preparation of the initial resource estimate for a project); ò     accept that the change may not be gradual; and, ò     ensure that the project evaluation team is adequately resourced.   These objectives require recognition of the value of previous experience and the need to instill a true team approach amongst both staff and contractors associated with the project. Regular formal and informal communications between staff, contractors and other stakeholders in the project are an essential tool in ensuring personnel are aware of factors affecting their role in the project.

Jan 1, 2004

By V Rajakumar, S Trang

Titanium has the potential to become the third wave of light metals used in high volume applications, following on from aluminium and magnesium. These light metals have functional attributes that can meet many of the goals needed for societyÆs transition to sustainable development. CSIRO has initiated a Light Metals Flagship to focus additional R&D efforts in support of the light metals industry. The vision of the Light Metal Flagship is for Australia to lead the Light Metals Age by reducing the costs and environmental impacts through innovative technologies for these metals. Life cycle principles will be used to identify novel technology pathways for metal production and product manufacture that are more energy efficient, less capital intensive and incorporating eco-efficient material flow chains.Under the auspices of the Light Metal Flagship, a Life Cycle Assessment (LCA) of titanium metal production was carried out with mineral sands mining of ilmenite as the starting point. Upgrading of the ilmenite to synthetic rutile by the Becher process and titanium metal production by the conventional Kroll process were the processing routes considered. Two alternative processes for titanium metal production, the FFC Cambridge process involving direct electrochemical deoxygenation of titanium dioxide, and a plasma process for producing titanium powder from titanium tetrachloride were also examined using LCA methodology and compared to the Kroll process. The environmental impacts included in the LCA were greenhouse gas emissions (Global Warming Potential, GWP) and acid rain gas emissions (Acidification Potential, AP). The Gross Energy Requirement (GER) of each process was also determined.These results for titanium, along with those from previous LCA studies by CSIRO on aluminium, magnesium, steel and stainless steel production, were used to show that despite the relatively large amounts of primary energy required for the production of these light metals, their special properties (eg corrosion resistance, strength and light weight) mean that these metals offer potential GER and GWP reductions compared to other competing materials in a number of applications, when viewed on a life cycle basis. Two applications considered in the paper are the lightweighting of motor vehicles and chemical plant equipment manufacture.

Jan 1, 2004

By F H. Henrfquez, A G. Oroz

Design and operating conditions of large size mechanical flotation cells were evaluated by comparing them with actual operating conditions in a plant. The objective was to determine the time scale-up factor, typically based on empirical rules. Experiments were conducted on the rougher flotation circuit at Minera Escondida Ltd. The circuit consisted of self-aerated mechanical cells of 160 m3, arranged in six parallel banks with nine cells each. The rougher circuit flotation kinetics were evaluated from direct sampling and local mass balances around each cell of the bank. Adjusted overall mass balances were also developed. This information was used to fit different kinetic flotation models, and it was found that the rectangular distribution function was the most appropriate to describe the distributed rate constant for industrial operation. Then, a rougher flotation simulator was developed to describe the actual operation in terms of the operating variables (mass flowrate, solid percentage, feed grade) and the actual volumetric flowrate entering to each cell. In this study feed pulp samples were taken in parallel from the rougher circuit and were simultaneously floated in the laboratory. The kinetic behaviour was then modelled at a laboratory batch scale in order to determine the time scale-up factor between laboratory batch flotation data and industrial size flotation. The time scale-up factor observed for large sized cells, 160 m3, was found to be reasonably similar to those previously determined for self-aerated mechanical cells, but of lower size, operating at similar recoveries. In addition, the relative effect of mixing, between laboratory batch and an industrial flotation bank, was quantified by the parameter, separating the impact that kinetic and mixing changes have on the time scale-up factor. In general, the rougher flotation operation was found to reach the predicted metallurgical target, and the optimal separability criterion was also respected. The diagnostic generates information about the internal state of the process and helps to identify potential improvements for design, operation and control of the circuit.

Jan 1, 2005

By H Matsuno, N Oyama, T Yamamoto, K Nakajima, Y Iwami, N Saito

Recently, the quality of sinter feed ore used in sintering process has deteriorated. In particular, Fe has decreased and gangue component has increased in the sinter feed ore. Increase of gangue is not only the factor to influence sinter qualities, but also the factor to increase coke ratio in the blast furnace operation as the increase of slag ratio. Therefore, to cope with the deterioration of iron ore qualities, studies on alternative iron ore resources and development of its utilisation technology have been required.In that kind of new iron ore resources, authors focus on high-grade magnetite fine. High-grade magnetite fine decreases sinter productivity by the decrease of permeability of sintering bed. Therefore a new study for using large amount of magnetite fine is required. In the past, there are some studies about the effect of mixing ratio and size of magnetite fine on productivity and quality, but there are few studies about magnetite fine segregation in charging.In this research, the melting behaviour and interfacial reaction calcium-ferrite, which has important role as bonding agent among iron ores, melts into hematite substrate and magnetite substrate was studied. As the results, it was defined that upper segregation of high-grade magnetite fine is suitable for productivity of sintered ore. Based on this knowledge, the control method of high-grade magnetite fine segregation by magnetic force at charging was studied with DEM (discrete element method) and its verification experiments for magnetic segregation control was conducted in the laboratory.CITATION:Iwami, Y, Yamamoto, T, Oyama, N, Matsuno, H, Saito, N and Nakajima, K, 2017. Improvement of sinter productivity by control of magnetite ore segregation in sintering bed, in Proceedings Iron Ore 2017, pp 61–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Study on Treatment of Wastewater Containing Heavy Metal Ions Using Modified Oceanic Cobalt-Rich Crusts

Sep 13, 2010

By R R. Large

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of orogenic gold deposits is commonly a two-stage process. The first stage involves preconcentration of gold in a suitable source rock, such as carbonaceous black shales, felsic volcaniclastics or komatiitic volcanics. The second stage involves the release of gold (commonly with arsenic and/or tellurium) from the source rocks during metamorphism or magmatic intrusive events, accompanied by the replacement of source rock pyrite by pyrrhotite. Recent research suggests that synsedimentary gold trapped in the structure of diagenetic arsenian pyrite in reduced carbonaceous facies of continental margin sedimentary basins is an ideal source of gold for many orogenic and Carlin-style gold deposits. The conversion of diagenetic arsenian pyrite to pyrrhotite during basin closure and greenschist facies metamorphism is the key process releasing gold and arsenic to the metamorphic fluid, with metal deposition in structural trap sites to form the deposits.CITATION:Large, R R, 2015. Orogenic gold deposits – a two-stage process of gold enrichment, in Proceedings PACRIM 2015 Congress, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By T Perera, B Fan, S Thang, T Hsia

Minerals are valuable resources and critical elements for a broad range of biological and technological applications, including technological developments to improve energy efficiency and the global movement to promote a low-carbon economy. However, in order to extract these critical metals, large amounts of waste and toxic chemicals are generated, as well as the use of high energy and large amounts of water consumption. Froth flotation is one of the most commonly used processes to separate and collect high-value minerals, but it still has some limitations, including low flotation efficiency performances using existing collectors and other reagents. Therefore, there is an urgent need to design and develop new metal-specific collectors to more efficiently separate and recover valuable minerals and to allow bulk water recovery from flocculated tailings. In this research, we propose to use our newly designed and synthesised novel collectors derived from a type of vitamin E (α-tocopherol), a relatively inexpensive and non-toxic natural molecule. As a potential collector-building block, α-tocopherol has a long hydrophobic carbon chain that facilitates the attachment to air bubbles during the froth flotation process. In addition, the phenol group of this molecule can be easily modified to incorporate various functional groups for targeting different types of minerals. Furthermore, α-tocopherol can be converted into a monomer for polymerisation by the reversible addition-fragmentation chain-transfer (RAFT) process, which can provide us with polymer based-collectors with high precision control of molecular weight and architecture. So far, small-scale qualitative experiments on α-tocopherol-based collectors have been performed with good results, which indicates the feasibility of these compounds as novel collectors for improved froth flotation processes.

Aug 24, 2022

By Beer G

The recent re-emergence of an Integral Pressure Stripping system which operates with both cell and column in closed circuit at elevated temperature and pressure, requires no cyanide in the eluate solution and has greatly reduced carbon reactivation requirements in seen as a progressive step in this area. Several of these re-configured IPS systems have been placed in service in Australia and overseas in the last three years, with the first of the new generation units constructed and commissioned by Como Engineers Pty. Ltd. at Mt. Fisher in the East Murchison of W.A. in September 1987. This plant was relocated to a new ore body at Darlot W.A. in February 1989. Use is made of a data base of raw plant performance figures from both Mr. Fisher and Darlot and its performance compared with other operating plants. Initial commissioning difficulties of the Mt. Fisher prototype and dis- cussed together with the modifications and operational procedures required to overcome these problems. Stripping times of less than 6 hours at 145 degrees have been achieved with barren carbon values less than l O ppm from loaded carbon values above 3000 ppm and with cell pass efficiencies reaching 90 per cent.

Jan 1, 1991

Conveyor belt haulage offers the advan tages of continuity of operation, minimum labour requirements, and the ability to handle large volumes of material over extended periods. However, breakdown of critical con- veyors in the system can cause undue and substantial losses in production output at the working faces, unless adequate surge bin capacity is incorporated in the haulage system. A conveyor belt simulation programme, code name 'Beltsim' was developed by Bucklen et al (1968) at the Virginia Polytechnic Institute in the U.S.A. and provides a quantitative measure of the performance of a conveyor belt network design. A limitation still exists with the computer programme and involves the inability of the programme to predict the necessary surge bin capacity to overcome conveyor belt downtime. The computer programme was modified to overcome this limitation, to simulate a con- veyor belt breakdown, and to provide a quantitative prediction of the surge bin capacity necessary to permit a modern mining system to operate effectively and continuously.

Jan 1, 1977

By M I. Pownceby, S P. Suthers, V Nunna, G J. Sparrow

Global demand for iron and steel has increased substantially over the past 20 years and there has been a greater focus on developing suitable processing options to treat low-grade hematite-goethite ores containing higher levels of silica and alumina impurities. The processing applicable to reduce the impurity levels in these lower-grade iron ores depends on their mineralogy and a thorough understanding of the process dynamics associated with the separation technology. Different separation technologies used to remove silica and alumina from low-grade iron ores were reviewed. The major concentration methods that may be applied to upgrade lower-grade lump iron ores include magnetic separation, wet and dry heavy media separation, and air-pulsed jigging. The technologies applicable to beneficiating iron ore fines include wet and dry gravity and magnetic separation, flotation, and roasting followed by magnetic separation. It is necessary to investigate the application of separation technologies on a case-by-case basis to select economically viable beneficiation strategies suitable for the particular low-grade iron ore. A commercial flow sheet is expected to involve the implementation of several separation technologies.

Nov 8, 2021

The borehole televiewer is a downhole geophysical logging device that produces continuous, oriented, 360¦ images of the drill hole wall. Two types of borehole images are currently being generated at the BHP Billiton Mount Whaleback deposit. The optical televiewer (OTV) tool captures a ærealÆ image of the borehole wall whereas an acoustic televiewer (ATV) generates an image through variations in physical borehole size, scattering the energy from an acoustic beam. Orientation of the resulting ævirtual coreÆ is derived through magnetometers and accelerometers, providing values within one degree for both inclination and azimuth. Downhole structures such as fractures, joints, foliations and bedding planes are selected directly off the borehole image, recorded and displayed in a 3D modelling package along side adjacent drill holes. Measurements are corrected from apparent to true dip and magnetic to true north. Strata-bound magnetic anomalies are identified and corresponding measurements excluded. The importance of borehole imaging increases substantially with its ability to integrate the OTV and/or ATV data with other forms of lithological and structural data. At Mount Whaleback, the borehole televiewer has been implemented to provide information for geotechnical exploration including structural analysis, lithological characterisation and rock-mass conditions. Within the large area in and around Mount Whaleback, drilling may intersect a number of different geological formations with various rock types and conditions. With the application of the borehole televiewer, reverse circulation drilling can provide information traditionally obtained by diamond drilling.

Jan 1, 2007

The homologous series of saturated fatty acids investigated in this study generally show a steady gradation of properties with chain length. The solution pKa values were assumed constant at 4.9, however reported pKa values could be lower or higher. Hematite flotation response and surface pressure for aqueous solutions of these fatty acids were measured as a function of pH. For the shorter chain fatty acids, the undissociated acid was shown to be the predominant surface active species with flotation, supplemented by the physical adsorption of acid anions as the chain length increased. The reduced solubility of the longer fatty acid carbon chains made these reagents ineffective as flotation agents. The maximum flotation response of hematite using tetradecanoic acid corresponded with the precipitation edge of the reagent. The results show that the values of surface pressure of the surfactants are not always a good indication of their effectiveness as flotation collectors.

Jan 1, 2005

This paper highlights the agricultural sector's primary concerns with mining in New Zealand: the information gap, land rehabilitation and compensation. It suggests how these issues can be resolved between the competing land uses in the interests of New Zealand.

Jan 1, 1981

Commercially interesting deposits of zeolite rich tuffs and amorphous silica have been discovered recently in the Taupo Volcanic Zone (TVZ), North Island, New Zealand. This paper reviews them and comments on the potential for further discoveries. Potential markets for these unusual industrial minerals are discussed.

Jan 1, 1997

By H Kim, M J. Sun

In order to reduce carbon emissions from the steelmaking process and achieve carbon neutrality, global steel companies are establishing their own medium to long-term strategies and implementation plans using competitive technological advantages held by each steel company. At this point, Hyundai Steel has formulated a product-oriented carbon-neutral strategy based on innovative processing that makes use of Hyundai Steel’s own strength. Based on our experience in electric arc furnace product manufacturing and blast furnace operation in an integrated steel mill, Hyundai Steel is driving the Hy3 (Hy-cube) project, which involves a unique hybrid production system utilising hydrogen and hydrogen-based renewable energy sources. This initiative aims to achieve carbon-neutral production and eventually specialise in producing premium carbon-neutral automotive parts. The project has originality in that it involves not only designing processes using electric furnaces to produce premium steel products such as car body panels and electrical steel sheets, but also aims to reduce carbon emissions from the process, developing carbon-neutral products based on market demand. To assess the feasibility of the Hy3 project, Hyundai Steel conducted two pilot productions. The first pilot was producing a prototype of lower-arm part using electric arc furnace with three different kinds of raw materials: molten iron, HBI (hot briquetted iron), and scrap. Successful performance evaluation of auto parts with 1 GPa strength was achieved. The second pilot has been focused on tire cord steel, with the first-phase tests yielding a 33 per cent reduction in carbon footprint (CFP). Using the advantages of operating experience in electric arc furnace, Hyundai Steel is preparing for test operations producing various automotive parts using an electric arc furnace (EAF) to advance the Hy3 concept. From a medium to long-term technological development perspective, Hyundai Steel’s blueprint includes producing high-end carbon-neutral steel products using hydrogen-reduced iron as raw material.

Jun 19, 2024