Search Documents

Contact Angle Measurements on Lignite Surface

Sep 13, 2010

The prospect of utilization of phosphate ores which contain high P205 values associated with Al and Fe has produced a great deal of interest over many years. Processing options have generally been based on the utilization of by-products which were required to offset the processing costs.This paper presents a range of processing options which have been investigated at laboratory or technical scale on phosphate ores which predominantly consist of crandallite, CaA13(PO4)2(OH)5.3H20 and millisite, Ca(NaK)Al6(PO4)4(OH)9.3H20. Christmas Island (Indian Ocean) and Mt. Weld (Western Australia) phosphate ores are good examples of such feedstocks. It is expected that these processes may also be applicable to such phosphate ores from other locations.

Jan 1, 1990

By J L. Mauk

Low sulfidation epithermal deposits are important sources of gold and silver, and are considered the extinct analogues of modern geothermal systems. The aerial extents of alteration halos that surround twenty-two epithermal deposits range from 4 to 315 km2, with many less than 60 km2. Deposits with alteration halos <30 km2 typically have well defined limits, whereas deposits with alteration exceeding 30 km2 are commonly complicated by overlapping alteration centres related to adjacent epithermal deposits or other deposit types (i.e. high sulfidation, porphyry). Irrespective of the physical coverage of vein or alteration halos, both large (>60 km2) and small (<20 km2) deposits can contain large amounts of gold and silver. The size ranges for twenty-one analogous liquid-dominated geothermal fields from around the world have a restricted size range of 5 to 60 km2 and irrespective of physical size, commonly have multiple zones of focused fluid upflow. From an exploration perspective the comparison between epithermal deposits and geothermal fields provide the following four important points. 1) Alteration halos surrounding epithermal deposits as well as those for analogous geothermal systems show a range of sizes, although most are less than 60 km2. Therefore, where alteration exceeds 60 km2 multiple vein systems related to several paleogeothermal systems are predicted. 2) Multiple upflow zones are common in geothermal fields of all sizes (5 to 60 km2) and although difficult to demonstrate in epithermal deposits there is a strong possibility of discovering several discrete adjacent mineralised centres. 3) The orientation of veins parallels the principle orientation of the surrounding alteration and where alteration is wider than the vein strike length, this could suggest the occurrence of adjacent veins. 4) The physical size of both veins and alteration zones is not important in relation to amount of contained gold, as both large and small can contain large amounts of gold. These conclusions provide insight into the physical size limits and hydrologic structure of these paleogeothermal systems and highlight the potential for multiple mineralisation centres within a single alteration halo.

Jan 1, 2004

By X Yang

White phosphorus (P4) is a critical element in industry, but its current production from phosphate rock using the carbothermal reduction method raises significant environmental and health concerns. This pressing issue necessitates the development of new technologies that facilitate the sustainable production of P4. In response, my team is actively developing an innovative, coke-free approach for white phosphorus production. This method involves the dissolution of phosphate rock in molten CaCl2, followed by the extraction of P4 through electrochemistry at relatively low temperatures. Moreover, this approach has the potential to utilise phosphate-bearing solid wastes as raw materials, further enhancing its environmental benefits. By employing this cutting-edge technique, we aim to revolutionise the phosphorus chemical industry towards greener and more sustainable practices. This paper provides evidence of the feasibility and effectiveness of our proposed approach.

Aug 21, 2024

Mine planning includes equipment selection as a subprocess because aging equipment must be replaced to maintain or improve productivity levels. The criteria used for decision-making in mine planning and equipment selection are often inextricably linked and inherently contradictory. For example, financial wisdom demands that development, which is an expense and locks up capital, be deferred as far into the future as possible yet on the contrary technical knowledge suggests that developing well ahead of stoping is practically desirable because it generates additional geological information required to improve planning of the unmined portion of the orebody and create better operating flexibility. Consequently, mine planning professionals have to delicately balance all decision criteria when executing mine planning in order to achieve optimal mineral extraction or when selecting equipment, so that capital is optimally deployed. These two processes can therefore be characterised as belonging to the multi-criteria decision analysis (MCDA) type of problems. MCDA problems are alternatively referred to as multiple attribute decision-making (MADM) problems and belong to a broader group of problems called multi-criteria decision-making (MCDM). There is now a gradual recognition and application of MCDA techniques in the minerals industry. This paper explores the theory, current and potential application of these techniques in decision-making in the minerals industry.

Dec 6, 2010

By A Querzoli, B Williams

In late 2014 the Flinders Power Management Team was executing business improvement plans to ensure continued electricity generation until 2028 and beyond. Six months later, in June 2015, the Board announced the closure of the Flinders Power South Australian business, including the Leigh Creek Coal Mine, the Northern and Playford Power Stations located at Port Augusta and the 250km railway line. The announcement was preceded by a brief period of internal planning. A date was soon set for ceasing coal mining operations, being November 2015. The mine is unique in many ways. Located approximately 550km north of Adelaide the site has over 100 years of history and was formerly operated by the South Australian Government. Privatisation in 2000 saw the mine continue operation under Perpetual Leases from the South Australian Government. The leases included exemptions from multiple sections of the Mining Act 1971, obliging primary regulation under the Mines and Works Inspection Act 1920. The coal, being a low rank sub-bituminous brown coal, is prone to self-heating and spontaneous combustion. The mine and company town Leigh Creek were the economic and cultural heartbeat of the community. Facilities at the mine were shared by the community and vice versa. While many mines across Australia and the world enter periods of care and maintenance, few have been actively closed to the point of relinquishment (Bennett and Lacy, 2016). A swift decision to close, followed by a short mining operations shutdown period, presented significant technical and regulatory challenges for both the mine operator and for Regulators. The subsequent joint risk mapping process employed by Flinders Power and South Australian Mining Regulators was a unique real-world example of collaborative mine closure planning and execution. Lessons learnt are valuable for all mines, production facilities and for Regulators, even for those who may wrongly assume that closure is many years away. CITATION:Williams, B and Querzoli, A, 2018. Risk management for minesite closure planning and execution – start now! Lessons from the closure of the Leigh Creek Coalfield, South Australia, in Proceedings Life-of-Mine 2018, pp 68–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By R Bradford, W Gift-Agbey, T Vorster, P Morgan, E Grobler

The Asanko Gold Mine in Ghana started processing ore from the Nkran pit in January 2016 at a production nameplate of 3 Mt/a. The flowsheet is a conventional SAG, ball mill and pebble crusher (SABC) with gravity-gold and carbon-in-leach (CIL) recovery. The nameplate production was comfortably achieved within 3 months, so much so, that it was clear the SABC circuit was capable of processing more than the downstream section of the plant. Consequently, a program of de-bottlenecking was initiated to rectify volumetric capacity constraints. This program was later referred to as ‘Project 5 Million’ (t/a) or P5M. Having completed the de-bottlenecking exercise, it became evident that the SABC circuit could not reach 5 Mt/a solely on hard rock from Nkran. The new challenge was therefore to increase the capacity of the milling circuit through a focused comminution initiative that would address the following: geometallurgical treatment plan; upfront fragmentation requirements; installation of feed and mill monitoring equipment; and integration of a knowledge-based control strategy. This paper takes the reader through the various measures implemented to increase the milling rates and to create a stable/ sustainable control philosophy. As a result of the implementation of advanced mill performance monitoring technology (MillSlicer) and the collaboration between a team of experts in comminution, control and operations, the Asanko Gold Mine process plant feed tonnage has successfully increased from 3 Mt/a to 5 Mt/a.CITATION:Bradford, R, Gift-Agbey, W, Grobler, E, Morgan, P and Vorster, T, 2018. Optimisation of Asanko’s Obotan SABC circuit to achieve ‘Project 5 Million’, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J S. J van Deventer

Geopolymerisation is a new technology that processes and transforms aluminosilicate minerals into mechanically strong and chemically stable products. In this investigation, minerals such as fly ash and kaolinite were used as the solid raw materials for geopolymerisation. Inorganic salts were added to the geopolymeric pastes to simulate ionic contamination during processing for building and construction applications. The resultant products were examined and characterised physically. It was found that the early strength development of geopolymeric pastes could be changed according to the nature as well as the extent of the contamination. At a small dosage, the effect of the contamination on the early geopolymeric system depended heavily on the nature of the artificial surfaces that were created in the geopolymeric solution through the addition of the chemical additives. For example, the samples containing MgCl2 and Mg(NO3)2 had shown the same yield stress developments due to the similar surfaces that were formed. The cations of these salts were expected to hydrolyse and form magnesium hydroxide precipitates immediately after the addition to the early geopolymeric systems. The calcium cations of CaCl2 also precipitated upon addition, but the nature of the surfaces of these hydroxides was quite different to those of the magnesium hydroxides and gave rise to different yield stress development. The samples that contained the insoluble salts (in water) demonstrated different yield stress development when compared to each other because of the different nature of the additive surfaces that were exposed to the geopolymeric solution. These results suggested that heterogeneous nucleation could be responsible for the change of the rheological behaviour upon inorganic salt addition. When the extent of the ionic contamination was large, the anions released from the insoluble salts (in water) changed the nature as well as the concentration of the geopolymeric solution and the setting processes were retarded. Oxides, in general, behaved very differently from other salts, indicating the uniqueness of the oxygen anions in a system rich in hydroxyl and silicate anions. The inorganic salt contamination in geopolymers did not show any significant signs of structural change according to the XRD diffractograms collected. The seven-day compressive strength was not lowered by the inorganic salt contamination and it could sometimes be beneficial to the product performance, for example, an increase of 20 MPa was induced by the addition of calcium oxide. Inorganic salts as chemical additives have demonstrated the potential to modify setting times of geopolymers without sacrificing much of the productsÆ strength and integrity.

Jan 1, 2000

By R Sridhar, M Fe, W G. Bacon

The problems of magnetite build-up have plagued the non-ferrous pyrometallurgical industry for many years. To better understand these problems, a study was undertaken to determine the thermodynamic variables that affect the behaviour of magnetite under different smelting conditions. Equilibration studies were performed in the nickel smelting systems of matte-gas and matte-slag(silica saturation)-gas. The relationship of thermodynamic variables such as temperature, sulphur and oxygen partial pressure and matte grade on iron and magnetite activities were calculated and the significance on smelting parameters such as metal losses and partition coefficients were defined. The experimental data from this study were employed to develop practical methods which could be used to control the build up of magnetite, as well as to obtain additional metallurgical benefits. In general, a lower sulphur partial pressure and higher temperature operation was shown to enhance the metallurgical benefits of nickel smelting by decreasing the magnetite activity. Operating in this manner can also have added benefits such as higher metal recoveries, more efficient vessel utilisation and efficiency and lower smelter emissions at equivalent or higher primary furnace matte grades.

Jan 1, 2000

By M Fahey

Large volumes of tailings are produced annually by the goldmining industry of Western Australia. This material ishydraulically discharged into large storage facilities usingsub-aerial deposition methods. Much of the gold comes fromhighly weathered rock, resulting in tailings with significant claycontents. Consolidation of these materials can be very slow,particularly if occurring under the effects of self-weight alone.To optimise the consolidation behaviour of the tailings, disposalstrategies can take advantage of the effects of evaporation byallowing each tailings layer to dry before the next layer isdeposited. In the last 20 years, much of the gold processing inWestern Australia has utilised saline groundwater. As the salinetailings dry, the surface will develop a thin salt crust. Laboratorytests have shown that these crusts can drastically reduce thesurface evaporation, adversely affecting the behaviour of thestorage. This problem has been the focus of an extensive researchprogramme, with the objective of obtaining a fullerunderstanding of the mechanisms controlling the coupledconsolidation and evaporation behaviour of saline gold tailings.Part of this study involved site investigations of a wide range ofstorages to ascertain their current states. Methods of gainingaccess to the tailings following deposition were developed.In situ testing and high quality sampling were conducted on each storage and samples returned to the laboratory for analysis. These investigations have enabled full characterisation of the storages to be accomplished. Examples of data are shown herein and the implications of the results are discussed.

Jan 1, 2001

By K Grohs, A Satriawan, S R. Pearce

Martabe gold and silver mine is operated by PT Agincourt Resources (PTAR) and is situated in northern Sumatra and comprises several deposits in steep terrain, and in a tropical climate, that are required to be developed in the optimal sequence for the best possible Net Present Value (NPV) return on the project. In addition, the waste rock from excavations and tailings from processing is a by-product to be scheduled and used for a number of purposes identified as part of life-of-mine planning. These uses include construction of the current integrated tailings storage facility (TSF) as well as future engineering construction and waste disposal projects which includes plans for a program of in-pit backfilling. These plans need to be aligned to ensure the waste rock and tailings can be contained relative to the production rate. Given that the site will have multiple open pit voids upon cessation of mining activities opportunities for integration of in-pit disposal of mine waste have now been assessed with technical studies to review the practicality of the approach with respect to operational challenges and conformance with closure planning requirements. This includes assessment of disposal of waste rock, tailings (including consideration of filtered tailings) and co-disposal of waste rock and filtered tailings.

Aug 2, 2023

The Lennard Shelf Operations owned by Western Metals Ltd evolved from the Cadjebut Zinc Lead Mine (BHP) in August 1994. Original production of 0.5 mtpa will rise to 2.0 mtpa at the end of 1998. Employees work a multiple of fly-in/fly-out (FIFO) rosters from the Kimberley region and the WA Capital. The three underground mines, treatment and services departments will employ approximately 300 people by the end of 1998. The expansion of the Lennard Shelf Operations as a remote mining location was based on a fresh look at management systems and employee rosters which were generated from many years of mining experience. This paper will endeavour to summarise these experiences and analyse some of their outcomes. Dealing with several mining methods, engineering difficulties, logistical problems and climate extremes, the Lennard Shelf Operations has managed social/employee issues with excellent results. Much time has been spent to get this correct for the Lennard ShelfÆs own set of circumstances. Employees and associated companies must expect continuing changes and improvement as Western Metals strives to continually improve its management systems and employee rosters.

Jan 1, 1998

The design and operating characteristics of the hydraulic cyclone elutriator were described in detail by Kelsall and McAdam (1963), and the method of operation of the commercially available version, the Cyclosizer, is described in the manufacturer's pamphlet (Anon). Complete details of the operating procedure are given in the relevant operating manual (Anon, 1964).The cyclones which form the basis of the Cyclosizer (Fig. 1) under normal operating conditions produce typical cut sizes of 44, 33, 23, 15, and 10 µm for cyclones one to five respectively for material with a specific gravity of 2·7. At the end of the selected elutriation period each sized fraction is discharged and collected for subsequent assay or analysis but all material rejected by the fifth cyclone (e.g. minus 10 \lm quartz) normally passes to waste. When this material is needed for separate study, although its amount and average analyses can be calculated by difference, it may be necessary to collect more than 250 I. of very dilute suspension, flocculate the solids, allow to settle, and decant off the supernatant liquid.This procedure is cumbersome and inconvenient and the simple technique to be described may offer some advantages. The temperature of the water fed to the Cyclosizer is maintained at a constant value for added reproducibility.PROCEDUREThe present overall treatment of the subsieve material (minus 37 \lm) fed to the Cyclosizer incorporated several refinements compared with normal operation and these may be best illustrated by anactual example. Material to be cyclosized (25 to 100 g depending on size distributIOn and specific gravity) is completely dispersed in water at 23 QC by vigorous stirrmg, using suitable dispersants if necessary, in a...

Jan 1, 1974

Study on Mineral Processing for a Cassiterite Ore in Southwest China

Sep 13, 2010

Surface Chemistry of Iron Ore Throughout a Processing Plant

Sep 13, 2010

By K Faure

At Sams Creek a gold-bearing, peralkaline granite pophyry dyke intrudes Ordovician-Silurian metapelite and quartzite. The granite porphyry dyke has a thickness of up to 40 m, extends discontinuously for about 8 km, and intrudes thin lamprophyre dykes along its contacts. The granite dyke and gold-bearing sulphide and quartz-siderite veins within it have been deformed and recrystallised during several phases of folding, the youngest of which is Early Cretaceous.   The unaltered granite porphyry is composed of phenocrysts of perthite, arfvedsonite, aegerine and quartz in a groundmass of the same minerals, with accessory ilmenite, rutile and fluorite. K-Ar dates of amphibole from the granite gave ages of 226 and 246 Ma, but these ages may be a minimum due to resetting during the thermal and deformation events that have affected the area. Unpublished Ar-Ar data on amphibole from the granite show disturbed spectra with high temperature steps around 300-315 Ma, which is consistent with the age of A-type granites in the Buller region. Further age dating of primary and hydrothermal minerals in the granite is continuing. At least three stages of hydrothermal alteration have been identified in the granite. Stage I alteration is characterised by high fO2 magnetite-siderite ¦ biotite, which is cut by thin quartz-pyrite veinlets (Stage II). These are cut by Stage III sulphide, quartz and siderite veins, and pervasive silicification represented by quartz-perthite-albite-rutile ¦ pyrite-siderite-sericite assemblages overprints the earlier alteration stages. Lamprophyre is altered to a siderite-chlorite-sericite assemblage. Stage III sulphide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite ¦ graphite, deposited by low fO2 H2S fluids. The gold contains 18-30 wt% Ag and up to 1 wt% Bi. Temperature of vein formation was estimated from vein quartz fluid inclusion homogenisation temperatures (Th 260-355oC, average 330oC), arsenopyrite-sphalerite thermometry (310-365oC) and quartz-albite stable isotope thermometry (340oC). The altered granite and the veins have been deformed, and recrystallised and competent sulphide minerals are fractured and brecciated. Alteration and mineralisation are confined to the granite porphyry and adjacent lamprophyre.

Jan 1, 2004

The planned extraction of deeper copper ore at Isa Mine has necessitated a review of existing equipment and methods to contain costs and improve working conditions. Mining is in progress for a crushing-conveying system to serve the deeper southern areas of the 1100 Orebody. This system will permit direct tipping of ore to the crushers and conveying of the crushed ore by cable belt conveyor to existing shaft loading facilities, a distance of about 2 km. To develop part of the conveyor drive a new machine will be used, the Robbins MM120 Mobile Miner, a joint development project between The Robbins Company and Mount Isa Mines Limited. The Mobile Miner uses a rotating cutting wheel to excavate headings 3.7 m high and from 4.7 m to 7.5 m wide. To ventilate the deep crusher complexes and associated development at high virgin rock temperatures, a refrigeration plant will be built on surface to reticulate chilled water underground. Bulk cooling of air to the 3000/3500 Orebodies and the southern crushers will be combined with the reticulation of chilled service water to the lower workings of the mine.

Jan 1, 1984

An Application of Depressant BK510 in Separation of Molybdenite and Bismuth by Flotation

Sep 13, 2010

Change is inevitable but learning from change is an option. Willingness to learn is one of the first lessons that a leader must learn. Get comfortable and get left behind. I propose to outline the main social changes which are taking place and their impact on the Minerals Industry. Also the changing way we do business and what are the skills needed to manage that change and diversity. How are Associations and Institutes responding to this ever changing environment? More specifically, what is my Vision for the Institute to assist professionals to achieve greater and continuing professional excellence in their chosen professions?

Jan 1, 2000

Optimisation of the Performance of Flotation Circuits Using a Genetic Algorithm Oriented by Process-Based Rules

Sep 13, 2010