Search Documents

By F Minz, P Lamberg, A Mwanga, C Lund, C Wanhainen, M Amiri Parian, J Rosenkranz

A geometallurgical model is currently built in two different ways. The first and the most common way relies on geometallurgical testing, where a large number of samples are analysed for metallurgical response using small-scale laboratory tests, eg Davis tube testing. The second, mineralogical approach focuses on collecting mineralogical information over the orebody and building the metallurgical model based on mineralogy. At Lules University of Technology, Sweden, the latter method has been adopted and taken further in four ongoing PhD studies. The geological model gives modal composition by the help of element-to-mineral conversion and Rietveld X-ray diffraction. Texturally, the orebody is divided into different archetypes, and liberation measurements for each of them are carried out in processing fineness using IncaMineral, a SEM-based technique. The grindability and liberation spectrum of any given geological unit (sample, ore block, domain) are extrapolated from the archetypes. The process model is taken into a liberation level by mass balancing selected metallurgical tests using the particle tracking technique. The approach is general and can be applied to any type of ores. Examples of ongoing studies on iron and massive sulfide ores are given.CITATION:Lamberg, P, Rosenkranz, J, Wanhainen, C, Lund, C, Minz, F, Mwanga, A and Amiri Parian, M, 2013. Building a geometallurgical model in iron ores using a mineralogical approach with liberation data, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 317-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Kam KM, Tran B

Statistical techniques of Box and Jenkins (1976) have been used to assess the existing control schemes and determine the dynamics of flash smelting furnace at the Kalgoorlie Nickel Smelter. Pertinent process variables, such as, oxygen flow, flux flow, matte grade and iron to silica ratio in slag, were considered in the analysis using routine operating data collected over two periods of operation. Results indicate inadequate control of some of the important variables. Dynamic characteristic parameters (dead time and response time) between a set of input and output variables were identified to improve optimisation of the existing thermodynamic model used for flash furnace control.

Jan 1, 1996

By G M. Mudd

Mine tailings represent one of the two largest sources of mine waste from the minerals industries (the other being waste rock). Given the problems of declining ore grades and growing production, tailings generation is increasing exponentially across the global mining industry. Common practice is for mines to build large containment dams to store tailings during operations, which are then rehabilitated following mine closure. At some sites, however, the controversial practices of riverine or marine dumping of tailings is still practiced. As recent tailings dam failures have shown, there are legitimate questions being raised about the long-term viability of leaving tailings above ground due to the risks of collapse and failure. At present, it is rare for mines to emplace tailings back into former mine voids following mine closure, most commonly into a former open pit mine void (although a fraction of the tailings may be used for underground mine backfill, this is minor in scale). The approach of in-pit tailings has numerous advantages, such as inherent physical stability, low to negligible acid and metalliferous drainage (AMD) risks, as well as allowing more productive use of formerly mined land. In tropical areas where surface repositories are prone to leakage with potential for AMD and widespread dispersal of radionuclides (in the case of uranium mining), in-pit management provides particularly strong advantages – thorough hydrogeological studies are required, however, to address residual groundwater contamination risks and to establish sound, long-term environmental monitoring regimes for groundwater quality and subsidence issues. This paper presents a study of in-pit tailings management and compares it with surface repositories established in a tropical climate. The comparisons lead to the conclusion that, at least under tropical conditions, in-pit tailings management should be considered as world’s best practice – especially for radioactive uranium tailings.

Aug 8, 2011

By A Audétat, W T. Li

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Middle and Lower Yangtze River metallogenic belt is one of the most important polymetallic resource areas in China. Iron oxide-apatite deposits, mainly distributed in Ningwu and Luzong volcanic basins, are a distinct type of iron deposits in this region. These deposits have a close temporal and spatial relationship with Mesozoic dioritic porphyries and are characterised by magnetite-apatite-pyroxene/actinolite ± anhydrite assemblage and large-scale sodic-calcic alteration.Widespread multiphase inclusions in pre- to main-mineralisation stage pyroxene and garnet in Meishan (in the Ningwu basin), Luohe and Nihe (both in the Luzong basin) iron deposits were trapped at ~780°C in extremely saline brines (~90 wt per cent NaCl equivalent), consisting of Na (13–24 wt per cent), K (7–11 wt per cent), Ca (~7 wt per cent), Fe (~2 wt per cent), Cl (19–47 wt per cent) and SO4 (3–39 wt per cent), based on petrologic, microthermometric, Raman spectroscopic studies and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analyses of natural fluid inclusions and synthetic analogues. The high Cl/Br, Na/B and S/B ratios in brine inclusions and the heavy sulfur isotopic values of anhydrite and pyrite (d34SAnh = +15.2 to +16.9‰, d34SPy = +4.6 to +12.1‰) suggest a significant contribution from both halite- and anhydrite-bearing sedimentary rocks. The involvement of evaporites caused the production of large amounts of high-salinity brines with apparently enhanced capacity to extract iron from the dioritic intrusions.According to their geologic features and the above characteristics, these iron oxide-apatite deposits are considered to be a special type of iron oxide copper gold (IOCG) deposits characterised by high contents of Na, Ca, Cl and SO4 in the ore-forming fluids. Moreover, we believe that evaporite-bearing sedimentary basins are more prospective than evaporite-free ones for these kinds of deposits.CITATION:Li, W T, Audétat, A and Zhang, J, 2015. The connection between evaporites and iron oxide-apatite deposits, Yangtze River, China – laser ablation inductively coupled plasma mass spectrometry analysis of Na, S, Cl and Br in fluid inclusions, in Proceedings PACRIM 2015 Congress, pp 623–630 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Hale Y. M

Multielement reconnaissance geochemistry coupled with ground scintillation gamma ray measurements has been used to investigate the dispersion patterns of uranium and other major and trace elements in the arid Palmyrides region of central Syria. This region occupies an interplatform depression in the northern part of the Arabia Plate, upon which sediments up to 10 km thick have accumulated. Outcrops of strongly fractured Mesozoic and Cenozoic rocks form two major mountain belts, the northern and southern Palmyrides, between which is located the closed Ad-Daww basin, with a thick Neogene and Quaternary clastic cover. Among the various lithologies, phosphorites are well represented. Uranium and associated elements have been incorporated into the Upper Cretaceous and Lower Palaeogene sediments, especially the phosphorites, which are well represented in the region. These elements are derived from three possible sources, namely, sea water, Lower Cretaceous volcanism and metalliferous fluids leaking along taphrogenic lineaments. In and around the phosphorites, numerous traces of secondary uranium mineralization occur. Over 500 geochemical samples of outcropping rock, wadi and playa sediments, overburden and groundwaters were taken over an area of approximately 9000 sq km. Most samples were analyzed for 25 major and trace elements by nebulization ICPAES; for As, Sb, Bi and Se by hydride generation and ICPAES; and for U, Th and La and other REE by neutron activation analysis.

Jan 1, 1988

By Girnau G

The necessity of effective dust suppression measures during excavation work is just as uncontroversial in tunnelling as it is in mining. In many respects, in fact, the applied technology is comparable. Notwith- standing, given more careful appraisal, it becomes evident that very different starting conditions exist in both these fields: In mining, there are for instance, well organised firms, which in many cases have been active for several decades, carrying out the required drivage and winning operations - and although there are also experienced firms in tunnelling, these generally speaking form a joint venture in order to accomplish a certain project. These "tunnelling firms" which are formed for a short term, normally only exist for a period of two-to three years. They con- stantly reorganise themselves: from the site supervising engineers by way of the foremen and shift overseers to the gangs working on site. The "firm's headquarters" are also re- located when a new project is started up. Then of course, there is often pronounced fluctua- tion among the crews of a single tunnelling project. Seen from this point of view, a safety expert in tunnelling has a far more difficult task than one in mining. He has not the advantage of knowing every corner of the mine for years if not decades on end, of being familiar with the overall organisation of the enterprise let alone knowing many of the men at the face. This ideal prerequisite for effec- tive decisions pertaining to suitable measures for industrial safety and accident prevention taking all weaknesses into consideration given the interplay of the most varied system com- ponents, can practically only be arrived at in mining.

Jan 1, 1987

The problem of stability of the development working at the great depths of coal winning is of great seriousness. Numerous researches of the problem were carried out in the USSR, the results of which determined that raising of resistance of existing support will not lead to a considerable rise of working output. It is necessary to try to find ways at the expense of heightening the support ability of rock massif. For these purposes it is necessary to direct it correctly and in proper time. While carrying the development working the most intensive deformations of rock occur at a depth of 30m from the entry face. The zone of destruction of rock around the work is realised here for 60 to 70 percent. These facts show that in influence zone of entry face a kind of embryo of the working steadiness is forming, which greatly determines its following conditions. Therefore, it is necessary to begin direction of mining pressure around the work directly in a face.Complex research of the mechanism was carried out starting with the effect of moving face upon the surrounding rock massif. It was ascertained, that the zone influenced by the face is a section of 5 equivalent diameters of the work by the length within which the rock of the sides, roof and floor, experience the cyclical influence of stresses at the time of cyclical shift of the face. The elastoplastec deformation is occurring with it at the moments of rock removal and the deformation of creeping takes place at such intervals.

Jan 1, 1991

By C D. Pocock

Maintaining catch berm capacity in open pit mines through controlled blasting prevents production delays associated with managing risks associated with wall instability. A method has been developed to quantify the drill hole deviation of presplit holes at Century Mine. Different controlled blasting techniques are used to control wall quality and decrease the risk. The performance of presplit drilling, in terms of deviation from design has been investigated. A methodology has been developed to quantify the drill hole deviation in three dimensions. This methodology was converted into a series of algorithms capable of handling an extensive range of data. The methodology was applied to a case study at Century Mine to evaluate the performance of drilling on two presplit blasts. Overall, 67 drill holes were investigated in the case study. The drill hole deviation was quantified in terms of three parameters: skewness, linearity and drill hole deviation parameter. Methods for quantifying each parameter were developed. Skewness, a measure of the amount of curvature and linearity, was defined as the measure of the consistency of the gradient of the drill hole. Drill hole deviation parameter is defined as the average measured deviation of the surveyed drill hole position from the design position. Acceptable drill hole deviation tolerances for each of the defined parameters were developed by analysing drill hole deviation parameters with respect to implications to catch berm capacity. Verification of the methodology was confirmed through the comparing of the completed drill hole deviation results using both visual inspection and cross analysis for each of the three methods. Holes with an R squared value of less than 0.97 for skewed deviation were classified as having skewed deviation, while holes with a difference in gradient of 3.5 were classified as having linear deviation. The results show that 76 per cent of the drill holes had deviation. Of this, 19 per cent were skewed, 57 per cent had linearity and 12 per cent contained both skewed and linearity deviation.

Nov 8, 2011

By A R. Hollis, M Heddon

The safe life cycle of a Tailings Storage Facility (TSF) is founded on the fundamentals of proper design, construction, operation and closure. Leinster Nickel Operations (Leinster) utilises four active TSF cells that are cycled between filling (deposition), desiccation, and construction to meet a targeted rate of rise. This results in ongoing and consistent raising of the TSF walls. Critical to maintaining the safe life cycle through this consistent wall raising is precision construction and high frequency quality assurance to ensure compliance to design requirements and TSF walls free from defects. Leinster has recently deployed Intelligent Machine Control technology for TSF construction. Advances in Intelligent Machine Control have decreased variability in construction; ensuring variations are within the tolerances of design. The Intelligent Machine Controls are programed to ensure construction conforms to design tolerances of +/-30mm. This level of accuracy provides assurance of borrow area set out, compacted layers are as per design, compaction monitoring is within the zone placed, scarification between layers to prevent lamination is maintained, and batter angles are set to the correct grade. This level of control provides certainty that construction meets the design intent. In conjunction with Intelligent Machine Control, periodic drone surveys are conducted to verify construction against design. Advancement in survey equipment and techniques allow higher frequency, high accuracy survey to be completed on demand by site based personnel. This provides quality assurance through all stages of the construction phases, as well as the final constructed wall, ensuring compliance to design. Combining Intelligent Machine Control with higher frequency quality assurance provides an increased level of certainty that the TSF construction is defect free and within quality specifications. These recent technological advancements in Construction and Quality Assurance ensure cell raises are constructed to the design intent with greater levels of accuracy and precision than ever before.

Jul 1, 2021

By L Rachmad

Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) deposit which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. Evaluations were made on former block caving mines at PT Freeport Indonesia (IOZ, GBT Area I and II) in order to design a more appropriate support system. As a permanent support, the thread bar bolt support system is widely used in the DOZ mine. The advantages of this system are ease of operation, quality control and high bond strength. The main problem of this system is the curing time of about 28 days to achieve maximum strength, necessitating the installation of a temporary support for its implementation. In this instance, the system was inefficient in operation and studies were required to find an alternative grouting system. This paper examines the evaluation of thread bar bolt support system and compares the performance of two types of grouting (resin cartridge and cement cartridge) with cement grouting performance. The evaluation is conducted with a pull out test. The advantages and disadvantages for each grouting method, comparison of cost estimation and grouting application in mine scale are presented in this paper.

Jan 1, 2002

By D Van Doorselaere

The purpose of blasting during mining is to produce a muck pile that can be efficiently loaded and transported. There is an increasing awareness of the variation in muck pile characteristics and its economic implications. It is well known that good fragmentation by itself is not sufficient to optimise the muck loading efficiency. The swelling and configuration of the muck pile also significantly affect the productivity of the loading equipment. The characteristics of a muck pile depend upon the blast design parameters, explosive properties and rock mass geology. This study has focused on the dependence of muck pile configuration on blast design parameters, explosive properties and size distribution of the muck.The field work was done in two phases. In the first phase 12 blasts were monitored, while in the second, three blasts were monitored. The blast design parameters and explosive properties for each blast were documented and the following muck pile characteristics were measured:muck pile height and its distance from the facedistance of throwwidth of the power troughsize distribution by image analysis technique.The effects of burden, bench height, heave energy of explosive, row-to-row delay, powder factor and the mean particle size of the fragments on muck pile configuration were examined. It was observed that muck pile height and distance of throw are strongly influenced by the burden, bench height, heave energy of the explosive and the size distribution of the muck. The width of the power trough depends upon the row-to-row delay, powder factor and total burden. In addition, the effect of the fragment size distribution on the muck pile parameters has also been discussed.CITATION:Singh, S P and Van Doorselaere, D, 2015. The relationship between blasting parameters and muck pile configuration, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R L. Brathwaite

In New Zealand, volcanogenic massive sulfide (VMS) deposits are found in three main geological environments associated with: 1.   ophiolitic basalts of Oligocene age in Northland and East Cape (eg Pupuke, Pakotai, Parakao and Lottin Point); 2.   with chert and pillow lava in greywacke sequences of Permian-Jurassic age (Torlesse and Waipapa terranes; eg Kawau Island, Te Kumi and Maharahara) and their metamorphic equivalents (Haast Schist; eg Moke Creek and Waitahuna); and 3.   with greenschists (metabasalts) and metaserpentinite of Permian-Triassic age (Ponamu Ultramafics) in Westland (eg Bowen and Wilberg ranges). The deposits consist of small lenses of disseminated to massive sulfide minerals, mainly pyrite and chalcopyrite. Small quantities of copper ore were mined from some deposits in the 1800s (eg Kawau Island from 1846), with the last mining at Parakao from 1961 to 1966. Several deposits have been recently examined for their gold potential with assays on sulfide rock samples as high as 75 g/t Au (Lottin Point).

Jan 1, 2005

By P Minkkinen

"Pierre Gy showed in his early works that the results in estimating the variance of the mean value of continuous lots depends on sampling mode (random, stratified or systematic), except in the theoretical case that the measurand is randomly distributed in the lot. The experimental variance estimate calculated from samples taken from the lot is independent of sampling mode but depends on sample size and the type of the lot heterogeneity. Variography can be used to estimate the variance of the lot mean for different sampling modes.Gy also defined weighting error, which is made if a simple average is calculated from the assays of samples taken from a continuous object (eg from a process stream) where the flow rate varies with time and is correlated with the concentration of the analyte in the stream.The effect on sampling uncertainty of the three sampling modes and their interaction with the following factors in estimating the uncertainty of the mean concentration is studied using simulated lots, and lots having heterogeneity patterns similar to those of real data sets, including the effect of: the type of heterogeneity (random, grading and clustered heterogeneity patterns) increment size and number employing composite sampling weighting error. CITATION:Minkkinen, P, 2017. Dependence of the variance of lot average on the sampling mode and heterogeneity type of the lot, in Proceedings Eighth World Conference on Sampling and Blending, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By A Bonani, R Molina, H Constanzo

With conventional undercutting sequence the infrastructure on the production level often has a short serviceable life before major rehabilitation is necessary and is characterised by high maintenance costs. The abutment stress zone is the main cause of this situation. The application of the pre-undercut caving method variant can increase the availability and utilisation of the production level When a pre-undercut is used development and construction are carried out underneath a previously undercut area, far away from the abutment stress zone, under more favourable stress conditions. This paper describes the design principles and the relevant results from the application of the pre-undercut variant over three years to the Esmeralda sector of El Teniente mine. The aspects described are the undercut-extraction, the undercut-development and construction distances, the geometry and drawbells opening, cave extraction rates, and the rate and height of undercutting.

Jan 1, 2000

By T Hill, J Everingham, P Clark

Currently, social impact assessment (SIA) is used to determine social impacts across the life-of-mine (LOM) to closure. This paper draws on recently completed SIA reports from the Martha gold mine in Waihi and qualitative interviews in the community that explored post-closure options, to review the challenges mining companies face when engaging with iwi4 through the SIA process and what that may mean for closure planning. The Maori of New Zealand consistently lobby to have a distinct voice in resource management issues. This is in line with the evolution of indigenous participation in SIA globally and with New Zealand policies, not least of which, the Treaty of Waitangi (the founding document of New Zealand) makes provision for Maori self-determination with regard to natural resources. Land use for mining has been a source of conflict for Maori and mining can have profound cultural and social impacts on the Maori community, yet despite Treaty intentions their representation in SIA has been comparatively limited. With this in mind, the Waitangi Tribunal has released the Ko Aotearoa Tenei (Wai 262) report, which recommends far reaching reforms to laws and policies affecting Maori culture and identity including natural resource management. This landmark report seeks to move the Maori-Government relationship beyond grievance to partnership. Given suggested policy changes in Wai 262 and the risks of poorly conceived closure planning, it is timely to review where Maori currently fit into the SIA process. The findings of this research suggest that improvements to the outcomes of this process will require companies to act beyond compliance. However, these improvements may also ensure mining companies maintain their social license to operate and to ensure continued influence across the life of a project to closure.CITATION:Hill, H, Clark, P and Everingham, J, 2012. æThere is an emptiness for Maori here in WaihiÆ - Understanding indigenous perspectives on post-mine land uses in closure planning, in Proceedings Life-of-Mine 2012 , pp 153-160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By M Wortley, J McKay, D La Rosa, O Guyo

It has been a generally held concept that crushing operations were, by their nature, too simple to benefit from the implementation of advanced process control. The commissioning of an OCS¬ expert control system and image-based oversize detection system, VisioRock, at the Pilbara Iron Tom Price facility are dispelling these notions. A constraint-based OCS¬ expert control system has been designed and commissioned on the high-grade crushing and screening plant along with a vision-based oversize detection system functioning on six product conveyor belts. To date, the expert control has demonstrated the ability to increase production by maximising dynamic constraint utilisation. Dynamic constraint utilisation is a concept developed by Rio Tinto Technical Services for effectively evaluating constraint-based control logic performance. The VisioRock system has been installed and configured and has been operating for a period of several months. Currently, Tom Price and Metso personnel are working to define correct oversize detection thresholds. Details of the plant implementation are discussed.

Jan 1, 2005

By C G. Ferguson, S L. Makin

The Cawse nickel project is a new generation pressure acid leach (PAL), solvent extraction and electrowinning process used to produce LME grade nickel metal and cobalt sulphide concentrate containing 40 per cent cobalt by treating nickel and cobalt oxide ores from a lateritic ultramafic profile. The project is located 50 kilometres NW of Kalgoorlie in Western Australia. The commercial success of the Cawse nickel operation is dependent in part upon the ability of the principal ore type to be beneficiated. A simple process of rejecting lower grade material on the basis of particle size achieves this. The process is called upgrading and allows subgrade material to become commercial ore grade and also allows higher ore grades to be processed in the early parts of the operation. The success of the upgrade process is dependent upon the physical and chemical properties of the ore being processed and the nickel grade of the ore. The upgrade ore type represents >80 per cent of the Cawse nickel resource and is hosted mostly within a limonite unit, represented by goethitic clays in the upper saprolite zone. In the upgrade processing circuit the ore is crushed and slurried. It is then passed over a series of screens that remove all material over 0.5 mm. This ensures that coarse material is removed from the main ore stream. Upgrade is reliant on selectively rejecting lower grade or barren material, which can include silica, magnesite and relict saprock. To predict leach feedgrade, the grade control estimates the head grade and upgrade percentage for all ore delivered to the run of mine ore pad. To do this reverse circulation (RC) drill holes are logged for ore type, assayed for a range of elements and undergo simulated upgrade testwork. The percentage and grade of material rejected through the upgrade circuit has the most influence on upgrade per cent. This reject is determined by the physical properties of the rock mass and drum scrubber parameters. The correlation between nickel upgrade and reject can be established to predict upgrade from the known mass reject. Parcels of upgrade ore milled to date closely follow projected correlation trends. Upgrade circuit results have been excellent, with average nickel grades upgrading by 34 per cent, cobalt by 23 per cent, with 55 per cent mass passing.

Jan 1, 2000

Early in 1950 a new laboratory was set up to deal with problems in mineragraphy, petrology and metallography. This paper describes the equipment, the organisation and association of the laboratory with the various departments of the company, the work that has been done and future plans.At Mount Isa it was soon realised that the microscope would play a most important role in mineral dressing problems and aiding geological research.As early as 1928, R. J. Colony submitted a petrographic report on Black Star ore for Consolidated Limited; much later, in 1934-5 Dr. Grondijs published for Mount Isa Mines Limited a preliminary study of the Mount Isa orebody, followed by a mineragraphicinvestigation of mill products, and in 1937 a Study of Mount Isa Ores by H. GrondIjs and C. Schouten appeared in Economic Geology, for June-July. Other papers dealing with the petrology and mineragraphy of Mount Isa ores are appended at the end of the paper.The mill research metallurgical staff has endeavoured to incorporate mineragraphy in solving milling problems and determining the effectiveness of laboratory as well as examining minerals sent in by the geological department.For many years the amount of equipment available was limited and much of it was locally made or improvised. An improvised briquetting machine, and grinding and polishing lap gave moderate results in conjunction with an old, but serviceable, Leitz microscope. However, for more detailed and accurate work not possible with improvised equipment, many mineragraphic problems were sent to specialist in.

Jan 1, 1953

By G P. Bates

The rationale for the design of the Emergency Egress (escape andentrapment) strategy for one underground metal mine has beenpreviously described (Brake, 1999). Two of the key conclusionsfor this mine, which is equipped with 30 minute oxygen-generating self-contained self-rescuers (SCSR), were the need to ensure no person is ever more than 750 m from an emergency refuge station (ERS) and that it could take up to eight hours to rescue workers from undergroundå. These conclusions were based on a number of considerations including the non-availability of a credible, æpersonalÆ entrapment procedure at the workplace, the duration of self-contained self-rescuers when used for travel, the need for rapid æclearingÆ of mine personnel to effectively and safely target mine search and rescue resources and the maximum time to either put a fire out, or to rescue affected personnel. As there is no Australian standard for refuge stationsç (or for self-rescuers), this paper follows with guidelines for the location and specification of both fixed (permanent) and relocatable Emergency Refuge Stations (ERSs) that may be applicable to other underground Australian metal mines.

Jan 1, 1999

By M Xu and, P F. Wells, A N. Kerr, Y Shields

Triethylene tetramine (TETA) has been used in combination with sodium sulfite (sulfite) for pyrrhotite depression at Clarabelle Mill since 1998. This combination has been highly successful at reducing pyrrhotite levels in the bulk (Ni/Cu) concentrate. Although highly effective, the roles of TETA and sulfite are not well understood. Treating bulk samples of the circuit feeds through the miniplant enabled the effects of circuit configuration on the performance of the pyrrhotite rejection circuits at Clarabelle to be determined. Reasons for the different performance of the non-magnetic pyrrhotite rejection circuit in the miniplant were investigated and tested in the laboratory. The effect of different grinding environments in the laboratory was examined to better understand the depressing mechanisms of TETA/sulfite. Modification of the grinding chemistry improved the selectivity of pentlandite over pyrrhotite in the presence of TETA/sulfite at current plant dosages.

Jan 1, 2005