Search Documents

By H Park, V Sahajwalla

"Due to the increasing amount of gangues in iron ores, a beneficiation process is required more as a preliminary step for ironmaking process. However, mechanical grinding and washing of iron ore needs tremendous effort that increases operating cost. Therefore, there is a necessity of a novel approach to ironmaking which can tolerate considerable amounts of silica or alumina. In the present study, a high alumina-carbon composite pellet was examined for an ironmaking process. The effect of compositional changes in the CaO-FexOy-Al2O3-SiO2 oxide system on the reduction of carbon composite pellets was investigated in a purpose built thermo-gravimetric analyser (TGA) at 1473K (1200¦C). As a result, alumina increased the reaction rate of carbon composite pellets by increasing surface area, while silica decreased the reaction rate by lowering surface area of samples. Infrared gas analysis assisted with the reaction kinetics of carbon composite pellets through measurement of CO and CO2 in off-gases. This study will assist with establishing the new pelletising method which differs from the conventional fluxed pellets.CITATION:Park, H and Sahajwalla, V, 2013. Effect of CaO-FexOy-Al2O3-SiO2 oxide system on the reduction of carbon composite pellets, in Proceedings Iron Ore 2013, pp 467-472 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Sullivan T. D

The Lochiel Deposit is a large occurrence of soft brown coal about 130 km north of Adelaide. The deposit is undergoing continued evalua- tion of which an integral part was the excavation of a Trial Pit. The Trial Pit was deemed necessary to demonstrate that the deposit may be mined efficiently by draglines and the particular emphasis was on the geotech- nical and hydrogeological aspects of what may be termed difficult mining conditions. The dewatering of the Trial Pit was commenced in September 1986. After considerable planning and excavation was successfully completed in May 1987. The project is unique in terms of its size and technical com- plexity. It entailed excavation of over 230,000 m3 of overburden to an overall depth of 36 metres. The excavated material was utilised for experimentation in a Trial Dump. Included in the Trial Pit design were several novel techniques includ- ing depressurisation drains to improve mining conditions in soil strength materials and the use of vacuum to aid dewatering.

Jan 1, 1988

By Snowden D. V, Standing C. A, Ryba A, Bywater A

McKinnons open pit gold mine, located within the Cobar Basin in New South Wales, is characterised by complex mineralisation controlled by the intersection of steep faults in the hinge zone of an anticline. Resource estimation using indicator variography and indicator kriging was based on RC drilling on 25 in sections together with grade control RC drilling on 12 in by 12 in and 6 m by 6 in patterns. Rigorous sampling and checking procedures were used to verify the reliability of the drill hole data. Blast hole data was used to assist grade control in defining ore block boundaries.

Jan 1, 1997

The Emmaville district is located in the northern part of the New England region of New South Wales some 400 miles north of Sypney. Better known for its substantial production of tin and tungsten ores, the Emmaville district has also been the centre of a small and somewhat sporadic production of copper, arsenic, silver, lead and zinc. This production has come principally from three mines-Webb's Silver Mine, Webb's Consols and, to a lesser extent, Pye's Creek Silver Mine.The ores from these mixed sulphide deposits are texturally and mineralogically complex and the problems of beneficiation are rather formidable.GENERAL GEOLOGYThe main rock type of the Emmanville district is a dark, brown to blackish massive siltstone of Permian age which overlies acid volcanics possibly also of Permian age. In places the siltstone gives way to conglomerates and standstones with discontinuous lenses of calcareous sediments (David, 1887).The whole series is folded but because of the massive character of the more expansive siltstone, detailed structure is difficult to delineate.Toward the close of Permian time the area was intruded by a series of intermediate to acid plutonic and hypabyssal rocks. Mineralization within the region is ascribed to the more acid of these intrusives-granodiorite, granite, and quartz-felspar porphyry (Lawrence, 1957, 1960).No intrusive rocks outcrop in the immediate neighbourhood of Webb's Silver Mine though granite occurs two miles...

Jan 1, 1961

By A B. Richards

A brick veneer house located on a open-pit coal mine lease has been subject to ground vibration levels of up to 222 mm/s, and air vibration levels of up to 145 dBL. The dynamic response of the structure was measured with accelerometers, geophones, and strain gauges as part of a project investigating the response of brick veneer houses to blasting. This paper outlines the project, and provides information on brickwork strength, foundation investigations, and observations on damage due to blasting. Correlations have been made between crack behaviour and factors such as blast vibration levels and rainfall.

Jan 1, 2001

By Iwu GO, Almond DP, Joasoo _

The gravimetric integral Knudsen effusion method was used to measure cadmium activity values in binary liquid In-Cd alloys in the range 523 to 573 K. The activity measurements together with other studies from the literature indicate that special bonding conditions exist in the melts near a composition corresponding to InCd3. Sound velocities in In-Cd melts were also measured using a precision pulse-echo over- lap method in the range 404 to 953 K. The frac- tional deviation of experimental and ideal isentropic compressibilities at 623K shows a functional dependence on composition with a pronounced maximum near the composition 75 at.%.

Jan 1, 1980

By D B, M A. Sares, D W. Coulter, D C. Peters

This presentation discusses NASA-funded research on the ability of hyperspectral remote sensing to map diagnostic acid rock drainage (ARD) mineralogy that adversely affects water quality within watershed and to determine the relative contributions of natural ARD sources of metals and acidity to that drainage. Ground-based reflectance spectroscopy, combined with water chemistry, is used to identify mineralogical and chemical variations throughout a watershed. Integrated with hyperspectral data acquired from airborne remote sensing platforms, such as the NASA Airborne Visible Infrared Imaging Spectrometer (AVIRIS) sensor, a methodology has been developed that should improve environmental assessments and tracking of impacts on and from drainages. Phase I of this project focuses on a drainage basin (Lake Creek), tributary to the upper Arkansas River in central Colorado, which is impacted by natural acid rock drainage from areas of high-sulfide hydrothermal alteration. This project builds upon research and inventory efforts by the Colorado Geological Survey (CGS) to identify hydrothermal alteration that is the primary source or is contributing to acidic and toxic drainage in Colorado. This presentation will cover ground and airborne hyperspectral remote sensing techniques and results and water analyses for seasonal high-flow and low-flow conditions in Lake Creek. Identifying correlations between mineralogy, especially mineralogy that can be identified through airborne remote sensing, and water chemistry is a key focus of this project. Of particular interest are low-pH iron phases such as jarosite, ferrihydrite, schwertmannite, copiapite, and transitional amorphous phases as well as AlOH phases from higher, although still acidic, pH environments which are observed to mix with the iron precipitates within the streams draining from the hydrothermal systems. Drainage in the Lake Creek watershed derives from the Grizzly Peak caldera (Oligocene), which exhibits extensive hydrothermal alteration. Alteration types include silicic, quartz-sericite, quartz-sericite-pyrite, advanced argillic, and argillic. By understanding the chemistry of a naturally impacted drainage and its relationship to the surrounding geology, the project goal is to allow more efficient and complete identification of such sources in mineralised terranes through remote sensing technology.

Jan 1, 2003

Mr Chairperson, respected leaders of the mining industry, ladies and gentlemen;   Good morning, Kiora, Nihao.   I am very honoured to give a speech to the 2005 New Zealand minerals conference. I would like to take this opportunity to express my sincere thanks to the Ministry of Economic Development to invite me to be part of this important event.   Today, I am going to talk about two themes: a brief introduction of ChinaÆs economic development, including ChinaÆs energy strategy; the good bilateral relations between China and New Zealand, its potential for further development and its relevance to our cooperation in the field of minerals and energy.   It is a well-known story that over the past 27 years, great changes have taken place in China. In 1978 when ChinaÆs reform and opening up just started, its gdp was near to only 150 billion usd dollars. By the year of 2004 it reached to 1.6 trillion usd, an average of yearly growth rate 9.4 per cent.   ChinaÆs great achievements are widely appreciated both in China and abroad. ChinaÆs development has not only improved the living standard of its own people, but also produced a huge market and brought about great opportunities for the world. Since ChinaÆs entry into WTO in 2001, China has imported near to 1.8 trillion usd dollars of goods, averaging a yearly imports of 500 billion usd dollars, creating for other countries and regions more than ten million jobs.   Our prediction is that in the next five years, ChinaÆs imports will be well over three trillion usd dollars. China will continue to serve as one of the leading growth engines for the future world economic development. Now China is on its great strive to achieve the goals of improving living standard for all the Chinese people. We are trying to reach a quadruple gdp of 2000 by the year of 2020, namely to reach gdp four trillion usd, a gdp per capita 3000 usd dollars.

Jan 1, 2005

By J Nortier, J Dray

There is no single factor that determines the appropriate capacity for a mining project. It is driven by the size of the resource, the capacity of the market, the availability of capital, the availability of power, the availability of water, and a myriad of other considerations. There is also no single solution to the question of how big the project should be. However, to develop a project, the study team needs to select the configuration options that it regards as the best for the project. To be able to make this selection, the study team should consider the range of available options and do so at a level of detail that gives it confidence in the conclusion but does not lead to multiple detailed design exercises. Having considered the range of options, and with a clear definition of the project owner’s objectives and constraints, the work to be carried into feasibility studies can be focused appropriately. This paper discusses the process of completing strategic mine planning to identify project configuration options to assist in the selection of the processing plant throughput rate (Capacity Study) for a large greenfield open pit mine. The processes described in this paper allow for the basis of design to be set for subsequent studies that meets the objectives at a risk profile acceptable to the owner.

Jun 22, 2022

By R H. Sibson

Magmatic and/or hydrothermal fluid systems in island or mountain arcs self-organise to critical states subject to perturbation by changes in the regional stress, which plays a controlling role in the containment of overpressured fluids. Whether the magmatic arc is under compression (eg Andes, northern Honshu) or extension (eg Taupo Volcanic Zone, New Zealand) is a key factor controlling the ease of magmatic or hydrothermal fluid ascent. Abrupt changes in the stress regime have the potential to induce major episodes of fluid redistribution. Large earthquake ruptures along plate boundaries may induce such changes over broad areas, also contributing to fluid redistribution by renewing fault permeability along the causative rupture zone or reactivating distant fault-fracture permeability by shaking from radiated waves. High-resolution geophysical investigations of active arc systems and the subduction thrust interface underlying their fore-arcs reveal repositories of overpressured hydrothermal fluids. In active magmatic arcs under compression such as NE Honshu or Cascadia, there is evidence for a heterogeneous distribution of overpressured hydrothermal fluids in the middle-to-lower crust trapped around the base of the upper crustal seismogenic zone. Investigations of the subduction thrust interface responsible for great (Mw = 8.0) ‘megathrust’ earthquake ruptures has revealed in some instances (Cascadia, SW Japan) the existence of a belt of non-volcanic tremor (NVT) with accompanying slow slip episodes defining the base of the megathrust interface at 40 ± 5 km and 350°C??-??550°C. Aqueous fluid at these depths is likely derived from dehydration reactions accompanying the basalt-eclogite transition in subducted oceanic crust. NVT sequences in the hanging-wall above the interface may be defining migration pathways into the overlying crust.The potential for eruptive episodes in magmatic arcs and redistribution of hydrothermal fluids is assessed in the light of the stress changes that followed the 2011 Mw9.0 Tohoku subduction thrust rupture which extended along strike for over 500 km and down-dip for over 150 km, with maximum slip of c 50 m.

Aug 22, 2011

The four major contracts for the construction of Museum Station are: 1) Installation of Soldier Piles, 2) Structural Contract including the temporary support, 3) Architectural Finishes which include Electrical and Mechanical Services and 4) Supply and Installation of lifts and escalators. Specific areas of interest include the fabrication, installation and removal of temporary support steelwork, the monitoring of ground loading, and the interface between the structure and. the temporary support. The information collated during construction confirmed the design assumptions and criteria. No major changes'were required in the design of the construction methods. The open cut excavation and construction of this major structure in an inner city area was significant by any standard and was successfully completed with minimum disruption to the public and without damage to adjoining or surrounding property.

Jan 1, 1981

By Rashleigh C

The selection and application of an effect- ive firing system first require a clear under- standing of the initiating abilities of the com- ponents in such systems. The conditions under which charges can be prematurely initiated by a detonating cord downline must be appreciated. This is a principal consideration in the design of a successful downline/'Anodet'/primer assembly. The advantages and limitations of an electric and several non-electric initiating systems are explained. The factors which in- fluenced selection of the two most suitable systems for use at Isa Mine (viz. downline/ 'Anodet'/primer assemblies and the reinforced long-lead 'Anodet'-type delay system) are dis- cussed. Blasts are detailed in which each of these has been applied. The initiating design for a hypothetical 2 x 106 tonne blast using electric short delay detonators and multi-channel exploders is presented. In this design, charges in remote blastholes are activated after the detonation of earlier firing charges by protecting the firing lines with sandbags.

Jan 1, 1978

Underground mine ventilation is now com monly simulated on a digital computer. Such a programme, incorporating natural ventilation has been modified by others to account for methane emission and elevated local tempera- tures. At Wollongong University, the pro- gramme was further developed and extensive interactive graphics incorporated such that any view of the three dimensional mine could be viewed, and superimposed upon that view are areas where a nominated parameter has exceeded a particular value - generally at a nominated time after a particular event and usually a fire/explosion of one type or another. A further programme was developed such that up to 20 'times' could be examined at a particu- lar location after say, a fuel rich fire at some other place in the mine. The output from this programme includes a plot of methane 1, smoke 1, temperature, pressure and air flow versus time - a most useful graphic to observe the limits of safe attendance in a particular Airway.

Jan 1, 1983

Heavy medium separation is widely used because of the precision of separation achievable and the flexibility of control. Good design is manifest in the eventual achievement of the operational objectives. These objectives which take account of the assessed quality of raw feed, market requirements and production cost levels need to be carefully prepared and realistic.

Jan 1, 1987

A new two-metre column self-heating test procedure has been developed at the University of Queensland, which clearly shows the hot spot development phases that take place in bulk coal self-heating. The column results provide a more reliable indication of the self-heating propensity of coal than small-scale index tests. At the same time, off-gas evolution patterns associated with hot spot development are obtained, including the recognition of hydrogen evolution from oxidation at temperatures less than 80¦C. Subtle differences in off-gas evolution from self-heating between gassy and gas-drained coal are also apparent. This new approach to coal self-heating assessment offers an opportunity to further the understanding of the complexities of spontaneous combustion and will enable more accurate risk assessment for the coal industry.

Jan 1, 2005

By L Nicholls, A Parbhakar-Fox

Reprocessing Queensland’s historical copper tailings for critical minerals is an opportunity to circularise the state’s mining industry by converting waste liabilities into assets. Mine waste valorisation enables economic rehabilitation of legacy mining sites, improves environmental outcomes, and can establish a secondary resources sector that produces a sustainable supply of critical minerals to supplement growing global demands (Australian Government, 2023). The North-West Queensland Minerals Province (NWQMP) hosts numerous copper mines with known cobalt mineralisation (Degeling, 2020). Cobalt is a critical metal essential for green energy and battery technologies, however its global supply is at risk due to geopolitical and ethical concerns (Rachidi et al, 2021). Historically mining in the NWQMP has focused on copper, leaving cobalt to theoretically accumulate in the mine waste. First-pass geometallurgical characterisation of waste repositories by the Sustainable Minerals Institute identified Capricorn Copper as a key site for further investigation into cobalt deportment and recovery potential.

Aug 2, 2023

By R M. Yanamandra, M Kumar, S K. Tripathy, N Mangadoddy, P Sudikondala

Spiral concentrators are one of the flowing film gravity concentration devices used to beneficiate coal and mineral ores. The aim of the current study is to understand the particulate flow and separation performance of an LD9 spiral concentrator using a multi-phase Computational Fluid Dynamics (CFD) model. The CFD model utilises the Algebraic slip mixture model to simulate particulate flows. The model employs the Renormalisation group (RNG) k-ɛ turbulence models to resolve the fluid turbulence. Initially, the volume of fluid method was adopted to track the water-air interface. Simulations were then carried out at low (0.3 and 3 wt.%) and moderate (15 wt.%) solids concentrations. Multiple particle-phase representing particles of poly sizes (75–1400 µm) and multi-densities (1450–2650 kg/m3 ) were simulated to study the particle segregation on the spiral trough surface. The numerical predictions are compared with the literature performance data at a diluted pulp flow rate of 6 m3 /hr. The results were found in close agreement. Further, the same CFD model is used to study the change in pulp velocity, streamflow rates, and separation performance at increasing solids concentration. For the same density particles, Fine particles mostly show higher volume concentration in the middle and outer trough regions, whereas coarse particles show higher volume concentration in the interior and central trough regions. It implies that the fine particles mostly segregate towards the outer region, and dense particles segregate towards the axial column.

Aug 24, 2022

At the Waikato North Head Ironsand operation, NZ Steel Mining Ltd is using a Bucket Wheel Excavator û shiftable conveyor mining system to excavate Titanomagnetite bearing sand and clay. The system utilises two Bucket Wheel Excavators with a two level shiftable bench conveyor and common trunk conveyor to deliver the material to a processing plant. The system was commissioned in November 1984 and has proved itself to be a high capacity, low cost method of excavating. Techniques of handling high sand faces have been developed and the conveyor layouts are going through a process of change to cope with the variable geo technical conditions and remain within: the characteristics of the excavators. The safety requirements for operating the system have been of a high standard and the experience has increased the confidence of the Company and the Mines Department Inspector's, for the first Bucket Wheel Excavator Mining system in New Zealand.

Jan 1, 1986

By Kuzmitch O, Morozov A

The main direction in the mechanisation in the mines of the Donbas and the USSR is long-face technology with complexes on the base of hydraulic supports. On the base of the 30 year old experience of exploitation of the coal clearing systems the serious data about the behaviour of the contained rock, display of underground pressure 'on longwalls and preparatory workings have been accumulated. Exploitation works in mines of the USSR are carried out at different depths: from 1000m to 1200m. There are 26 mines in Donbas, which exceed the depth of 1000m. It is the mines of Donbas, where is a rich experience of the exploitation of coal seams in various conditions. Besides, there are wide variations on the factors of the extraction thickness, depth of seam, angle of dip, occurrence of gas dynamics and others. In many scientific establishments, and in Donetsk Polytechnical Institute also, there are scientific research/results, which can be of interest for the coal mining countries.The volume of coal mining from longwall system-mechanised walls in Donbas became stable at the end of the 70s at level of 70 percent. All the efforts to increase this level have not given any notable results, not saying about the technical-economical data, which gradually deteriorate. It shows that positive progress in using the technology for the long walls is over and it is necessary to find new ways of mechanisation of coal winning.

Jan 1, 1991

By D Pienaar, B McFadzean, C T. O’Connor

Collector and frother molecules in sulfide mineral flotation are thought to have separate roles in the flotation process, where the collector selectively hydrophobizes the mineral surface and the frother adsorbs onto the bubble surface, inhibiting bubble coalescence. Molecular interactions have been observed between these molecules which allow them to co-adsorb at each of the respective interfaces, improving pulp phase recovery. This study investigated the molecular interactions between sodium diethyl dithiophosphate (SDEDTP) and hexanol, and the mechanism by which these interactions improve the recovery of galena. In this study each of the respective interfaces were investigated for the adsorption of SDEDTP. The adsorption of SDEDTP on galena was measured by UV-Vis spectrophotometry and isothermal titration calorimetry. At the air-water interface foam stability and pulp bubble coalescence was used to quantitatively discern if there are interactions between SDEDTP and hexanol. Microflotation and induction time experiments were performed to determine the effect of SDEDTP, hexanol and their mixtures on mineral recovery and bubble-particle attachment. The results of all these tests were collated to determine if SDEDTP-hexanol mixtures synergistically improve sulfide mineral recovery. It was found that SDEDTP reduced bubble coalescence in the pulp demonstrating activity at the airwater interface. Together SDEDTP and hexanol synergistically enhanced foam stability. This indicated that there are attractive molecular interactions between these reagents. Even though DTP did not adsorb onto galena, DTP-frother mixtures synergistically improved the recovery and attachment probability of this mineral. Adsorption studies with aeration showed that DTP in the presence of a frother transfers from the air-water interface to the galena mineral-water interface during bubble-particle collision. It was proposed that the transfer of hexanol through the thin film enhanced the kinetics of film thinning between the bubble and the particle by destabilising the thin film thus improving pulp phase mineral recovery.

Aug 24, 2022