Search Documents

By S Wainio, P J. Beckett, T Miller

Lichens are a symbiosis of fungi and algae. Air borne elements and gases are absorbed very efficiently over the entire surface of the lichen, because they have no protective structures such as a waxy cuticle or stomata. A survey in 1977 (one year before the Sudbury Regreening program began), indicated that several Cladonia spp had invaded the soil in Sudbury’s open birch woodlands. Pollution sensitive species such as Cladonia rangiferina and C. mitis occurred 20–25 km from the smelters. It was anticipated that the improvements in air quality and reclamation efforts would allow a natural invasion of pollution sensitive species into what once was a lichen desert that surrounded the smelters. The purpose of this project was to study the invasion of terricolous (soil-inhabiting) communities of lichens and mosses on reclaimed land in the Sudbury region 45 years after commencement of the Sudbury Regreening Program.

Aug 2, 2023

By M I. Pownceby, N Karimian, A Frierdich

These may be found with goethite through mechanisms including direct substitution or coprecipitation of nanocrystalline phases. Understanding P incorporation in goethite has significant implications for Australia’s iron ore industry as it lowers their commodity value. The current study tests a novel low-temperature technique to extract P impurities from synthetic goethite phases under O2-free ambient conditions by utilising Fe(II)-catalysed recrystallisation. The objective of this study was to examine the effect of the Fe(II)-catalysed recrystallisation of goethite on the geochemical behaviour (mobility and speciation) of co-associated P. To achieve this, we tracked changes in labile P (aqueous and 1M NaOH extractable) concentrations over time in goethite suspensions which were reacted with Fe(II)aq for 14 days under circumneutral pH conditions and room temperature conditions. Temporal changes in Fe mineralogy were investigated via synchrotron-based X-ray absorption spectroscopy. Iron K-edge extended X-ray absorption fine structure (EXAFS) spectroscopy confirmed goethite as the only mineral phase in P-free treatments while goethite (~86 per cent) and feroxyhyte (~14 per cent) were the main phases in 1.0 per cent P-containing treatments after a 14- day reaction with Fe(II)aq. According to our findings, the treatment of P-goethite with Fe(II) for a duration of 7–14 days, followed by a 24-hour extraction of the reacted solids using 1M NaOH, results in the removal of approximately 79.5 per cent of the initial P content. This removal encompasses both the aqueous fraction (~4.5 per cent) and the surface adsorbed fraction (~75 per cent) from the 1 per cent P-bearing mineral phase. Notably, this approach demonstrates an improvement in P extractability, with approximately a 10 per cent increase compared to the 1 per cent P-goethite sample that was not reacted with Fe(II).

Sep 18, 2023

The products of the steel tube industry play an important part in the production,' transrzission and refining of oil. Steel tube manufacturing is already well established in Australia and supplies the petroleum industry with its requirements" within the .present limitations of the various tube plants., With the discovery of oil in commercial quantities in this country, the steel tube industry could be expected to extend its scope to cover a much wider range; of oil country tubular goods, line pipe and refinery. Tubing.

Jan 1, 1962

By Golubkov OL, Fedotov PB, Shkylar FR

One of the fundamental parameters of the race- way is its extent (a{ o), which has a significant effect on the distribution of gas and material flows in the lower region of the furnace. pp The known relationships for determination of aC o in most cases link the length of the raceway with the parameters of the blast, while the para- meters of the coke layer, in which the raceway is formed, are either ignored or else expressed in terms which are difficult to determine experimen- tally. Furthermore, the coke combustion propert- ies are not always taken into account in current blast furnace operating practice with combined blast. A complex dimensionless parameter, which re- flects the properties of the interacting media, is the ratio of the kinetic energy of the hot, com- bined gas stream to the potential energy of the coke flow, burning at the tuyere in a gas of known composition. Statistical processing of experimental data on the extent of the raceway zone, obtained from literature and our own work on operational furnac- es, has led to a working formula of the following Form:

Jan 1, 1981

By D Chalmers, C C. Harb

The detection and control of gas levels in mining is a continuing challenge for the industry. Standard detectors have many problems that could be overcome with laser based spectroscopic instruments, but to date these systems have not been suitable for mining conditions. This paper reports the development of a new digital data extraction scheme to modernise traditional cavity ring down spectroscopy (CRDS). CRDS is a direct cavity enhanced laser based absorption technique, which is used to allow the identification of an unknown substance by their molecular fingerprint; this unknown substance is identified by analysing the ring downtime of the light exiting the optical cavity. Traditional CRDS has many issues when analysing substances in hostile environments, or when multiple species may be present. This presents an alternative approach, called real-time CRDS (rtCRDS) that has the potential to overcome many of these issues and produces systems that could be used in the mining industry. The system utilises newly developed widely tuning quantum cascade lasers combined with improved optical cavities and novel digital data extraction to produce spectra over a 1500 nm range in a few seconds. The ring downtime measurements produced are accurate and have high sensitivity and maximum signal to noise ratio. This paper discusses the technique, illustrating the advantages compared to traditional systems and show real-time spectra for a set of molecules of interest to the mining industry. This paper also provided an analogy between this approach and that used in digital communications systems, and shows that this scheme is ideally suited to provide a network of sensors in hostile environments.CITATION:Harb, C C and Chalmers, D, 2015. Real-time methane detection – modern digital laser spectroscopy for hostile environments, in Proceedings The Australian Mine Ventilation Conference, pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J Wen, P Hou, W Yu, M Hu, Z Jiang, C Bai

Vanadium titano-magnetite (VTM) is one of the important iron ore resources in the world. High viscosity and low fluidity are the basic characteristics of hot metal containing vanadium and titanium during the ironmaking process. Clarifying the influencing mechanism of the melt viscosity would be a significant issue for the high efficiency smelting of VTM. In this paper, a self-developed melt viscometer based on the principle of torsional vibration theory was employed to measure the viscosity of hot metal accurately. Simultaneously, the thermodynamic calculations and some modern detection methods were also used to investigate the precipitation behaviour of high-melting-point phases in hot metal containing vanadium and titanium. The measuring results show that the viscosity of molten iron gradually increases with the increase of titanium content when the mass fraction of titanium is between 0.09 wt per cent – 0.50 wt per cent. Meanwhile, the viscosity of the hot metal was affected significantly by the vanadium content. When the vanadium mass fraction was higher than 0.30 wt per cent, the viscosity of hot metal increased sharply, which will have a serious impact on the fluidity of the hot metal. Furthermore, it was revealed by thermodynamic calculations that an increase in titanium and vanadium content would result in the precipitation of high melting point phases such as TiC, TiN, VC, and VN in the molten iron, ultimately resulting in a decrease in its fluidity. Meanwhile, it was confirmed by Scanning Electron Microscope (SEM) observation that the precipitates in the hot metal were compounds consisting of V, Ti, C, and N elements, which agrees well with the thermodynamic analysis results.

Aug 21, 2024

By H Benzer, N A. Aydogan

It is well known that the high pressure grinding rolls (HPGR) can only be operated efficiently under choke feeding conditions in which a material bed is built up between the rollers to ensure interparticle breakage. By increasing the fines amount in the material bed up to a specific level with the recycling load, a uniform material bed is created and higher pressure gradient along the roller width is obtained which results in compact flakes including more fines. Extensive test work has been carried out with an industrial HPGR unit grinding cement clinker in a cement plant in Turkey. During the test work the recycling load of the circuit was changed to achieve different ratios to the fresh feed rate in order to identify the effect of the recycling load on the circuit performance. Six different tests were performed with the circuit at steady state. For each test, samples were collected from HPGR fresh feed and discharge, and total feed, then the particle size distributions of the samples were determined and mass balances around the circuit were calculated. The conclusion was that the reduction ratio of the HPGR increased with increase in recycling load. The flake densities showed the same trend with more compacted flakes being produced for higher recycling loads.

Jan 1, 2009

By A Jafari, N Khalili, M Vahab, P Broumand

This paper presents the implementation of the eXtended Finite Element Method (XFEM) in the general-purpose commercial software package COMSOL Multiphysics for multi-field thermo-hydromechanical problems in discontinuous porous media. To this end, an exclusive enrichment strategy is proposed in compliance with the COMSOL modelling structure. COMSOL modules and physics interfaces are adopted to take account of the relevant physical processes involved in thermo-hydromechanical coupling analysis, namely: the mechanical deformation, fluid flow in porous media and heat transfer. The model preprocessing, level-set-updates, coupling of the relevant physics and postprocessing procedures are performed adopting a coherent utilisation of the COMSOL’s built-in features along with the COMSOL’s LiveLink for MATLAB functions. The capabilities and performance of the proposed approach are investigated by examining several multi-field thermo-hydro-mechanical simulations with reference to the block caving process in mines.

Nov 29, 2022

Thiess Dampier Mitsui's Moura-Mine is located in the south-eastern corner of Queensland's Bowen Basin, some 180 kms west of Gladstone. Current requirements of the open cut operation are to drill and blast 25 million cubic metres of overburden per year, consuming some 12,000 tonnes of explosive in order to meet the requirements of the mine's four operating draglines and one overburden shovel. By early 1985 it had become obvious that the existing drill and blast equipment and technology could not cope with the long-term needs of the open cut mining operation. Three 61R drills were in need of rebuilding or replacement. Bulk ANFO trucks working two shifts per day were unable to match the requirements of the four draglines dne to long travel distances, slow discharge rates and their inability to load water-resistant products into the increasing number of wet holes. This paper outlines the significant steps taken to introduce new equipment and technology and the resulting improvements in the mine's productivity and economics.

Jan 1, 1986

By D Whitworth

The Golden Pig mine has embarked on a diamond drill program design philosophy that increases flexibility of the program by greatly increased drill pattern densities. The use of standard broad pattern diamond drilling at the Golden Pig mine has previously lead to operational inefficiencies and impacted significantly on the costs of the mine. The diamond drill program philosophy and its interaction with mine planning is explained. The case study of the E lode mining as used to internally justify the increased drill densities is detailed.

Jan 1, 2002

By D Bradshaw, E Forbes, M Edraki, M Tayebi-Khorami, E Manlapig

There is an increasing trend in the extraction and development of copper resources from complex deposits. These deposits pose mineral processing challenges, as they often contain low grade disseminated copper ore with high levels of impurities particularly arsenic. Although arsenic is a naturally occurring element, the concentrations of arsenic can be magnified by mining and mineral processing activities. Therefore, while arsenic has no significant market value, its presence in the ore deposit will have production, environmental and human health implications. The mining industry’s approach to life-of-mine planning has improved significantly in recent decades and managing arsenic is not an exception.CITATION:Tayebi-Khorami, M, Edraki, M, Manlapig, E, Forbes, E and Bradshaw, D, 2018. Arsenic pathways in copper mining – sustainability issues and potential solutions, in Proceedings Life-of-Mine 2018, pp 60–63 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By F

Ore reserve estimation has been described as the most individualistic, the most prickly and even the most controversial of all the technical aspects of the mining profession. This symposium is a great opportunity to look at the present state of the art and full marks must go to the Sydney Branch for organi- sing it at this time. The first essential of good ore esti- mation is probably an awareness of the uncertainties involved, and the possible impli- cations of these uncertainties.

Jan 1, 1979

By Grader F. E

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effective- ness of separation depends on the energising current of the separator, the frequency of the a.c. cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150um +74pm) on the linear motor surface has been observed using a cine camera. An attempt has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an a.c. cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear meter surf, e.

Jan 1, 1980

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

By Shuguang L, Jing S

Computer controlled truck dispatching systems is a newly-developed technical system in surface mines with shovel-truck technology. The real time dispatching criteria, as the core of optimal truck dispatching software, are analysed and a new criterion, complex dispatching criterion, is put forward. Dispatching criteria previously proposed include: 1. `Earliest Loading' (EL) - to assign a truck to the shovel at which the truck can be loaded earliest. 2. `Max Truck' (MT) - to assign a truck to the shovel at which the truck will have the shortest waiting time. 3. `Max Shovel' (MS) - to assign a truck to the shovel which has been waiting for the longest time. 4. `Minimum Saturation Degree' (MSD) - to assign a truck to the shovel at the branch where the truck flow saturation degree is minimum. 5. `Minimum Saturation Degree with Truck Cycle time consideration' (MSDTC) - as the MSD principle, with the truck travel cycle also considered. 6. `Fixed Dispatching' (FIX) - to assign trucks to fixed shovels. A system simulation model has been set up for truck dispatching system analysis. A few surface coal mines have been selected for case studies. Equipment waiting times and shift production of the system are obtained as the main outputs of the model. Simulation results show that each dispatching criterion has its own applicable range, no one can absolutely dominate the others. For example, when under-trucked, EL and MT criterion can obtain higher production than the MS criterion; when over-trucked, it is vice versa; while for MSD criteria, better results can be obtained no matter how the truck numbers fluctuate. From the view point of shovel output balance, large fluctuations occur for EL and MT criteria, while a good balance can be obtained for other criteria. In the light of dynamic change of mining system conditions, a single dispatching criterion is not necessarily reasonable. A complex dispatching criterion has been put forward to seek the complex optimum effect. Taking the advantage of each dispatching criteria, the dispatching result of a complex dispatching criterion dominates over individual dispatching criterion and a comprehensive optimum effect can be reached.

Jan 1, 1995

By B Hou

The Eucla Basin in southern Australia is emerging as an important global source of zircon from heavy mineral sands. Understanding the geological evolution of the basin and movement of heavy minerals down peripheral paleovalleys and along paleocoastlines is essential to effectively refine exploration strategies for heavy minerals in the basin. Integration of geoscientific datasets in a Geographic Information System (GIS) environment has proved to be effective in reconstructing depositional environments along the Cenozoic basin margin and in tracing the buried paleorivers that once drained broad areas of the Archean-Paleoproterozoic Yilgarn and Gawler cratons, the dominantly Mesoproterozoic Musgrave and Albany-Fraser Provinces, and the Neoproterozoic-Early Paleozoic Officer Basin. Sea level highstands during the late Middle Eocene (39 - 36 Ma) are associated with formation of the Ooldea coastal barrier complex and the zircon-rich heavy mineral deposits at Jacinth, Ambrosia and Tripitaka. More extensive transgression during the Late Eocene (36 - 34 Ma) built the complex Barton shorelines that host the Cyclone deposit and the extensive ilmenite-dominated occurrences of the Barton West prospect. Multi-generation reworking of the source sands is indicated by the high proportion of deposits that are zircon-rich relative to titanium minerals. The age distribution of zircon grains in heavy mineral concentrates from the Ooldea and Barton barrier systems points to the Musgrave Province as the predominant ultimate zircon source. Paleorivers discharging along the northern basin margin presumably carried a sediment load that was then redistributed by easterly longshore drift to build the extensive coastal sand deposits along the northern and eastern basin margin. The south-eastern extension of these deposits was reworked during Miocene-Pliocene (15 - 2 Ma) times into a series of regressive strandlines that show angular discordance with the Eocene coastlines. This discordance is consistent with evidence for long-wavelength tilting of the Australian continent from Middle Miocene times, as the continent drifted toward a dynamic topographic low induced by convective mantle processes associated with the South East Asia subduction systems. The Dromedary and Gulliver’s deposits probably formed at this time. Ongoing research is focused on the geological features of the basin that influence heavy mineral transport, concentration and preservation, and the processes leading to deposits with high zircon content.

Oct 5, 2011

By A R. Cruden, M S. Egglseder

The formation of banded iron formation (BIF)-hosted high-grade iron ore deposits in the Hamersley Province, Australia has been debated for decades. Although a structural control on their formation is widely accepted, only the roles of large-scale structures (ie faults and folds) formed by brittle and ductile deformation have been considered to date. However, the deformation of multilayered sequences in the Hamersley Province (ie the Mount Bruce Supergroup), with their contrasting rheological behaviours, creates challenges for understanding the complex structural framework at regional to deposit scales, including the significance for mineralisation and orebody location.Our approach to understanding these complex relationships is based on an established principle of structural geology, which is to extrapolate microscale structures to deposit-scale structures and vice versa, supported by state-of-the-art 3D modelling techniques. Complexly deformed hand samples associated with the Mount Tom Price iron ore deposit (Hamersley Province, operated by Rio Tinto Ltd) have been analysed and visualised with 3D explicit (Move™, Midland Valley Ltd) and implicit modelling software packages (Leapfrog™, AranzGeo Ltd) and supported by microstructural investigations (optical and X-ray microscopy) and fieldwork.Our study shows that the deformation of BIFs in the central Hamersley Province is controlled by microscale chemical processes (ie dissolution precipitation creep) due to rheological differences between iron oxide and chert layers, contrasting fluid flow properties and layer thickness variations. These processes account for the removal of vast amounts of silica, its transportation by diffusion in the presence of a fluid and reprecipitation at low-pressure sites. Consequently, this structural framework was used by different upgrading fluids to form iron orebodies.CITATION:Egglseder, M S and Cruden, A R, 2015. Evolution of a structural framework for high-grade iron ore deposits, in Proceedings Iron Ore 2015, pp 255–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By L W. Palmer

"Evaluating the geological risk associated with ore deposits is becoming common practice in the mining industry. While geostatistical simulation is a useful tool for evaluating this risk, the effect of applying different types of simulation is less understood. For simulation of categorical variables like rock types, available methods perform simulation in fundamentally different ways. In this study, the geological risk relevant for informed mine planning is studied with two categorical simulation methods, PluriGaussian Simulation (PGS) and Sequential Indicator Simulation (SIS). Risk is expressed as a probability of repeated occurrence of lithological units in the same location across simulations. Significant differences are observed between the methods in terms of spatial distribution of risk. To identify the most plausible risk model, the input parameters at every step of both techniques are scrutinised. PGS and SIS inputs are classified as four parameters that are: fundamental to implementation of the methodfixed to enable comparison of PGS and SISdetermined by user interpretation, hence variablenormally optimised during application of PGS and SIS. The effect of parameter selection from categories 1 and 4 on the risk model is investigated using drill core data from a leucogranite deposit. A corresponding block model is created for assigning outputs from PGS and SIS. Risk models produced by either method are illustrated in a cut-out from the block model to enable bench-by-bench comparison. For PGS, risk associated with relatively rare lithologies is relatively sensitive to variation of parameters. Independent of the abundance of lithology, a location-dependent effect of variogram and vertical proportion curve parameter selection is observed, with risk increasing towards the deposit edge. Although SIS requires fewer inputs, single lithologies must be modelled in turn. Using small numbers of samples in the search neighbourhood, all risk models differ substantially. For larger numbers of samples, the risk models are similar. Overall it appears that the risk model produced using SIS is less sensitive to changes than PGS but further work is required to confirm this.CITATION:Palmer, L W and Glass, H J, 2014. Risk associated with rock type prediction using simulation techniques, in Proceedings Ninth International Mining Geology Conference 2014 , pp 217–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By G Harbort, V Lawson

Mount Isa Mines Limited operates one of the worldÆs largest underground mines in North West Queensland. ItÆs mining and smelting complex produces copper anode, crude lead bullion (containing silver), and zinc concentrate. Copper is recovered in the Copper Concentrator from chalcopyrite ore, converter smelter slag and rotary holding furnace (RHF) slag via grinding and flotation operations. During 2002 a project to optimise cleaner circuit capacity was commenced. Its aims were to minimise copper losses and minimise slag/chalcopyrite cross contamination by reconfiguring existing flotation equipment and the addition of new flotation capacity. To minimise cross contamination a Jameson Cell was installed and dedicated to cleaning of slag concentrates, which had formerly been conducted by three flotation columns operating in series. The flotation columns were re-configured to operate in parallel and dedicated to upgrading chalcopyrite concentrate. In addition a Jameson Cell was installed to reject entrained copper from a prefloat concentrate consisting of talc and carbonaceous pyrite. This paper discusses the logic behind the cleaner circuit expansion, recent test work relating to the Jameson Cell and the installation and commissioning phases. Difficulties relating to the commissioning are reviewed and the solutions to problems are highlighted. The benefits the reconfigured circuit has provided to Mount Isa Mines are also discussed.

Jan 1, 2003

By Q Zhuo, P C. Pistorius, M N. Al-Harbi

A likely increasingly important pathway for future low-carbon ironmaking and steelmaking is the combination of gas-based direct reduction with electric furnace steelmaking (DRI-EAF route), or with electric smelting (DRI-ESF route). In the DRI-EAF route, the gangue that is present in the iron ore is fluxed and removed as slag in the melting (steelmaking) step. This is in contrast with integrated steelmaking, in which the gangue is removed as part of blast furnace ironmaking. For DRI-EAF steelmaking, the amount and composition of slag depend on the iron ore composition, flux additions and iron yield. Slag volume and composition affect phosphorus removal, foaming behaviour and the process energy requirements. In this work, heat data from a year of DRI-EAF production was analysed to test whether the expected relationship between slag volume and electricity consumption for EAF steelmaking was observed. The data include slag analyses (one sample per shift), and heatlevel information on all inputs, final steel temperature and dissolved oxygen concentration, electricity consumption, tapped steel mass and tap-to-tap time. In analysing the data, the slag volume was estimated from the assayed slag CaO concentration and CaO inputs to the EAF. The expected effect of slag volume on steelmaking energy consumption was calculated with a mass and energy balance, considering the heat of mixing of the slag. The calculated energy requirement of slag formation is in line with previous estimates reported in the literature.

Aug 21, 2024