Search Documents

By Case JE

Complete Bouguer and isostatic anomaly maps compiled for Costa Rica provide new insights into the crustal structure and mineralization. Terrain corrections were approximated from the station to a radial distance of 167 km by computer using a 3- minute digital elevation model of Costa Rica and surrounding areas. Isostatic corrections, based on Airy-Heiskanen compensation, were also calculated from 0 to 167 km using the 3- minute elevation model and from 167 km to 180 degrees using combined topographic and isostatic reduction maps. Costa Rica can be divided into four main terranes based on gravity data: a Pacific coastal region, a Pacific inland area, a central region, and a Caribbean coastal region. Negative gravity anomalies along the Pacific coastal margin correlate with an offshore sedimentary basin, and large positive anomalies correlate with mafic and ultramafic igneous rocks on the Santa Elena, Nicoya, and Osa Peninsulas, and at Puerto Quepos. Pacific inland anomalies are separated from the Pacific coastal region by a steep gravity gradient, and over the Coast Ranges a major gravity low overlies a thick section of low- density sedimentary rocks. In the central region, a major gravity low occurs over a thick low-density Quaternary volcanic complex in the Cordillera Central, north of San Jose. A prominent feature of the Caribbean coastal region is an interrupted gravity low over the Limon Basin that reflects a thickening of low-density sedimentary rocks. A conspicuous gravity lineament, trending northeast separates northern and southern Costa Rica. The lineament is defined by the termination of several major gravity anomalies including those over the Coast Ranges, Cordillera Central, Puerto Quepos, and Limon Basin. In addition, the lineament correlates with other geological and geophysical data including: northeast-trending faults, the southern limit of large Quaternary volcanoes, the segmentation of the middle America volcanic belt, and a seismicity gap. This lineament may be the expression of a previously unrecognized major northeast- trending fracture zone in central Costa Rica. An important economic implication of the gravity lineament is a correlation with the termination of gold and porphyry copper deposits in Costa Rica.

Jan 1, 1987

The Que River Mine is a small under-ground base and precious metals mine located in north-western Tasmania. Current production rate is 220,000 tonne/yr from reserves grading 0.37% copper, 7.1% lead, 12.2% zinc, 195 g/tonne silver and 3.4 g/tonne gold.Ore is mined using longhole open stoping techniques. Cemented fill is placed in primary stopes to permit safe and efficient recovery of pillars. The operation is trackless with both shaft and decline access from surface.Ore produced is trucked 40 km by road to be sold to the Electrolytic Zinc Company of Australia Ltd., for treatment at their Rosebery concentrator.

Jan 1, 1985

By B Arthur, K Sexsmith, D Hockley, S D

At the proposed Crandon Project, mill tailings would be depyritised for upland disposal. The resulting pyrite concentrate would be disposed of in the underground workings as a cement-amended paste backfill. In the long term, the underground workings would be flooded and the potential for the paste backfill to generate acid would be limited. However, while the mine is operational, there is potential for oxygen ingress to the backfill that may lead to sulfide mineral oxidation and acid generation. A series of humidity cell tests were completed to assess the potential for groundwater contamination. To assess effects of surface area on oxidation, the humidity cell tests were conducted on moulded cubes of paste backfill. The tests were terminated at different intervals, and the cubes were dissected and examined mineralogically. Various leach extraction procedures were also used to assess the progress of oxidation and secondary mineralisation within the paste backfill. The test results showed that: the cement amendment significantly contributes to acid neutralisation and results in a lag in excess of one year before the onset of acidic conditions (in comparison to less than three weeks for the pyrite concentrate); the depth of oxidation in the paste backfill is restricted to about 1 mm after 107 weeks of testing; and secondary minerals form a distinct ærindÆ at the surface of the paste backfill. The results indicate that acid generation in the backfilled stopes would be minimal. The importance of including the surface area effect in the testing (ie using moulded cubes) is clearly demonstrated.

Jan 1, 2003

The winning and upgrading of mineral raw materials necessarily includes size reduction, which serves the liberation and production of marketable products from highly valuable and bulk materials. For crushing, the following factors can be duly accounted for depending on material type and the selection of the suitable machine: ò producing a particular size distribution, ò producing a particular grain shape, ò selective comminution, ò gentle comminution, and ò producing a size range required by a specific process and/or for a specific product.

Jan 1, 1993

By Koppe J. C

This paper describes the methodology developed to establish a sequentia mining plan applied to a coal mine, using computers. Firstly, isocontou. maps were generated from the drill holes and outcrop description information, representing the thickness and depth of the rock formation: present in the mine site. The procedure relies on the repeated application of the cross validation techniques, until the standard deviation of thi estimation is reduced to a minimum.From this map the coal reserves of the two coal seams, the overburdet (separated in hard and soft material) and the interburden were calculated After that, the maps were transferred in digital files to AutoCAI software, where different mining plan simulations were performed. 7b ore evaluation in each case was done automatically, including tonnages volumes and stripping relations. The final mine configuration consider the economic aspects of the operation.

Jan 1, 1993

By Rosmus P

Improper use of auxiliary ven- tilation units during heading operations may often result in the appearance of hazardous methane accumulations. This is the case especially when roadways are ventilated by a combined system with a short sucking pipe at face end performing as the dedusting installation. Uniform air inflow to the face end facilitates sucking off the dust clouds and creates conditions favourable for formation of local methane accumulations. The highest methane concentration occurs in the cutting zone between the rock cut and the pipe inlet, under the roof and by, the sidewalls. Permanent monitoring of methane concentration at face end employs methane sensors. The most important are: one on the road- header's boom behind the cutting head, and one at the air outlet from the dedusting installation.

Jan 1, 1988

By N Nosaka

Sinter plants currently have to use many types of ores with different properties due to the great demand for iron ores, which was driven by the massive growth in Chinese iron and steel industry. On the other hand, the development of iron ore mines is limited and the quality of iron ores is in a tendency of deterioration. Therefore, the quick evaluation of iron ores has become more important for a stable sintering operation. In addition to such a background, the CO2 gas emission should be decreased from sinter plants according to the Kyoto Protocol on reduction in greenhouse gases. The present paper first describes the methods for testing the metallurgical properties of iron ores, which use a small volume of sample mainly focusing on magnetite ore that is effective for reducing CO2 and NOx emissions from sinter plants. The sintering properties of ores are evaluated separately according to each stage in sintering process, that is: heating stage before melt formation, primary melt formation in adhering fines layer of pseudo-particles, and assimilation of nucleus ore particle with calcium-ferrite system melts.Next, the application of the tests to the blending ores is introduced showing examples of the studies on the effective usage of the magnetite ores with Marra Mamba type ores.

Jan 1, 2005

By Hebblewhite B, Humphreys D

An experimental mining project has been carried out in the Collie Basin to demonstrate the safe operation of total extraction mining techniques in the underground mines of the basin. To achieve this, it was necessary to design and install a means of controlling or removing groundwater so that goafing of the overlying strata could be safely achieved as part of the mining operation. The site chosen for the experiment was a triangular panel adjacent to Western No 6 (WD6) underground mine, which includes the 3 to 4 m thick Wyvern Seam beneath 130 to 180 m of overburden. The test area abuts a major fault on the downdip side. The overburden and underburden sequences include several horizons of permeable sandstones which form major aquifers. Water problems have long been recognized in all underground mines in the Collie Basin, and have previously prevented the successful application of total extraction mining. Following extensive hydrological investigations, dewatering and depressurization systems were designed to dewater the immediate roof aquifers and to depressurize aquifers higher in the sequence and in the floor. This would enable stable roof conditions to develop and controlled goafing to be achieved. The roof dewatering/depressurization procedure involved a combination of in-mine vertical roof drainage holes and conventional dewatering bores constructed from the ground surface above the mining trial area. The dewatering system was installed and operated for 29 months before the commencement of mining. Mining was eventually successfully completed in two trial panels using a retreat Wongawilli extraction system using bridge conveyors and continuous miners. Water inflow into the mine workings was channelled to a constructed sump area at the lowermost corner of the panel and pumped to the surface via vertical sump bores. The dewatering and depressurization measures adopted were successful in permitting the first controlled and systematic total extraction recovery of coal from the Collie Basin. This trial mining exercise demonstrated the potential for increasing substantially the recovery of coal from the Collie Basin, where previously recovery rates of around 30 percent from underground mining were commonplace, using only bord and pillar methods.

Jan 1, 1988

Mount Isa Mines' Hilton Mine was brought into large-scale production in 1990/91 at a time of sharply falling metal prices. To ensure the operation's survival and eventual prosperity there was an urgent need to reduce operating costs and increase revenue. A target of a 40 per cent increase in productivity over five years was set. Strategies to obtain the required improvements were developed on the basis of greater involvement and increased contribution from the workforce, major changes to the mining methods and the development and application of new technology. This paper describes the organisational, operational and technological changes that have been implemented at Hilton and presents the results achieved to-date.

Jan 1, 1993

A system for rapid on-line determination of weight percentage coal in slurry and weight percentage ash in coal has been developed at the Julius Kruttschnitt Mineral Research Centre, University of Queensland. The gauging system is suitable for use with coal flotation slurries or slurries having a maximum particle size of about 1 millimeter. The system is based upon measurement of gamma ray transmission; radioisotope sources emitting photons of two widely different energies are employed. The inaccuracies of measurement that would normally result from variable amounts of air entrained in the slurry are substantially reduced by pressurising the slurry to approximately 2MPa (300 psi) using a Mono pump. The equipment can be used to make measurements on more than one slurry stream by pumping streams sequent- ially. The system is being tested at the Peak Downs Mine of the Utah Development Company in Central Queensland. This paper describes the theoretical principles of the gauge design, the experience gained to date in the commissioning of the equipment, including the installation of a PDP 11/03 computer, and the progress made in developing satisfactory interpretations of the gauge count-rate output.

Jan 1, 1978

By Gole MJ

The Goodyear nickel prospect is located 45 km southeast of Kalgoorlie (31.04¦S, 121.80¦E) near the eastern boundary of Hampton Area - East Location 45 (Figure 1). Nickel mineralisation was discovered on the Goodyear prospect in March 1996 when a reverse circulation drillhole (GYC5), initially drilled in December 1995, was deepened to meet a minimum footwall penetration requirement of 20 in that had been set for the drill program. Approximately 3 in of sulphides averaging 4.9 per cent nickel was intersected from 296 metres down-hole, this being within 2 in of the first end-of-hole. Hole GYC5 was part of an eight hole drilling program undertaken by Titan Resources in late-1995. This program was designed to test whether nickel mineralisation in the Dunlop prospect, discovered by the Western Mining Corporation - BHP Camylia Joint Venture immediately east of the East Location 45 boundary, continued across the tenement boundary. The area targeted by the initial drill program had been explored by Western Mining Corporation in the mid-1980s using extensive surface sampling and a drilling program that included 17 RAB and percussion drillholes. None of these holes intersected nickel Mineralisation.\

Jan 1, 1996

The Blackwater Coal Mine is a modern open cut operation using large draglines for over- :)urden removal and shovels, loaders and trucks to mine and haul coal to the crushing and coal ?reparation plant. Operations at the mine are described in sequence following through overburden removal to the railing of product coal from the mine site. The close operating connection between the mine and washery, which results from the blending of raw coal into clean product via the qashplant bypass system, is stressed. Some features of special interest at Blackwater Mine, such as land reclamation and slope stability,are outlined.

Jan 1, 1974

By Moxon N. T, Berndt J. R

BHP-Utah Coal Limited's Peak Downs Mine is located in Cen- tral Queensland, approximately 200 km south west of Mackay. The annual raw coal production of the mine is over 8 million tpa, requiring the removal of about 40 million cubic metres of prime overburden. This is achieved through the use of five large draglines. The large depths of overburden (up to 55 metres) encountered over half the strike length of the mine enables cast blasting to be carried out in conjunction with draglines employ- ing the chopping method of digging. The objective of cast blast- ing is to use explosive energy to move as much material directly into spoil as possible. The additional costs of drilling and blast- ing are offset by reducing dragline rehandle. Two factors which are of primary importance to the design of cast blasts are initiation control and material velocity. High speed motion picture photography is a powerful diagnostic tool to quantify these aspects of blasting (Winzer, Montenyohl and Ritter, 1979; Chiappetta et al., 1983; Anon., 1983). The objec- tives of such analysis are to: 1. Determine the burden velocity, 2. Determine the time to initial movement (that is, the inter- val between a face hole firing and the initial movement of the burden), 3. Check the accuracy of the initiation sequence. BHP Central Research Laboratories (CRL) and Peak Downs Mine monitored a cast blast in the mine's Winchester Pit on 18 August, 1988. The objectives of this exercise were to: 1. Quantify current cast blast performance, providing a base case for comparison with modified blast design. 2. Compare two orientations of angled holes within the blast. 3. Assess the effectiveness of cast blasting utilising an air-deck. 4. Check blast timing with respect to burden movement times.

Jan 1, 1989

The Kangiara mine is located within the Middle to Upper Silurian Hawkins Volcanics of the Douro Group near Yass, New South Wales. The deposit is a po1ymetallic type within a rhyolitic tuff.The ore minerals comprise pyrite, sphalerite, botryoidal sphalerite, galena, chalcopyrite, marcasite, tetrahedrite, bismuthinite, bismuth, silver, electrum, chalcocite, covellite, and digenite. The gangue minerals are quartz, barite, calcite, and the host rock. Locally sericite occurs.Several distinct ore types can be recognized, mainly on the basis of their macroscopic textural appearance, and it is inferred from these general features that the mineralization had a submarine volcanic-sedimentary origin similar to that of the Kuroko deposits in Japan.

Jan 1, 1976

The late 1960's and 1970's saw the initial development of the coal resources of the Bowen Basin of Queensland. The projects developed relied on large scale, open-cut operations using draglines for overburden removal and, in the majority of cases, project viability could be established based solely on those open-cut operations. Many of the mines developed in the 1980's have the same characteristics.Unlike these mines, the German Creek Mine has limited open-cut reserves at low overburden to coal ratios, and planning of the complex involved a large open-cut mine capable of developing early cash flow, with phased introduction of underground mining to replace open-cut capacity as the strip ratio increased.

Jan 1, 1985

By Gostylla W

The economic feasibility of controlled district cross-cut recirculation is examined in this paper with particular reference to the most important mine ventilation network parameters. An algorithm is developed to express the annual cost of recirculation which is then compared to the annual cost of conventional ventilation using the University of Queensland Experimental Mine as a case study. The concepts of resistance ratio and volumetric efficiency ratio are introduced and used to analyse the economic feasibility of controlled recirculation within a mine ventilation network.

Jan 1, 1988

By Hunter GW

This paper gives an account of the filling system at Mount Isa from surface fill production to stope discharge underground. A brief explanation of the surface facility and reticulation is given prior to the discussion on aspects of underground reticulation. These include fill hole types, pipe and breastplate installation, wear characteristics, etc. The different types of fill and their respective applications is mentioned as a prelude to a general overview of the mining considerations associated with fill placement and its role in the long term planning strategy at Isa Mine. Some practical aspects of stope preparation and filling procedures are outlined for the various stoping methods. Finally a brief outline of future fill developments is given.

Jan 1, 1982

Alcoa of Australia's Western Australian bauxite mining operations in the Darling Ranges, southeast of Perth, present major challenges in the control of air blast. The close proximity of rural communities and the face profile make the traditional methods of air blast control difficult.An extensive blast noise monitoring programme has been established. The development of a computerised blast noise prediction model and the establishment of a radiosonde weather balloon facility have reduced blast induced complaints by a factor of ten.The meteorological factors affecting blast noise transmission are discussed and examples are given of adverse weather conditions for the southwest region of Western Australia.

Jan 1, 1983

By Palmer G, Dennis R, Clark A

The Ravenswood Mine in North Queensland is the first gold mine developed by Carpentaria Gold Pty Ltd, a wholly owned subsidiary of MIM Holdings Ltd. Carpentaria Exploration Pty Ltd began exploration at Ravenswood in 1978. However initial exploration of the main gold producing area (Buck Reef East) commenced in March 1987 when exploration rights to four key leases were secured. A rapid, co-ordinated exploration and development program produced gold from a heap leach operation nine months after the first costeans were dug at Buck Reef East. To treat higher grade ore found at depth in the Buck Reef East pit and the metallurgically more difficult Buck Reef West ore, a carbon in pulp plant was commissioned in May 1988. The mine is currently producing at a rate of approximately 40 000 ounces of gold per year. Ore at Ravenswood is hosted by hydrothermally altered diorites and tonalites of the Ravenswood Granodiorite complex. Alteration is controlled by planes of permeability formed by joints, shear zones and dilational breccias. The complex orebody geometry resulting from these controls required very detailed surface and drill exploration for adequate definition. Carpentaria's need for early cash flow meant that economic, mining and metallurgical considerations governed choices of exploration techniques, program timing, material and data collected. The initial reserve of 1.1 mt @ 2.87 g/t Au was defined by sectional polygonal methods. Grade control is based on geologic mapping and blast hole or channel sample assays. Ore is batched through the crusher and sampled to monitor grade control and mining performance. Minimal dilution has occurred. Gold content is greater than predicted by the reserve. Sprinkling of heaps commenced in November 1987. Changes have been made to the pad design and to the method of heap construction. Heap leach ore is treated at a rate of 400 000 tpa.

Jan 1, 1989

The effect of accurate detonator delay timing on blast results can now be studied with the development of the ICI Electronic Detonator. This detonator has an accuracy and precision orders of magnitude greater than the current range of pyrotechnic delay detonators. A series of field trials have been conducted to quantify the effect of delay accuracy and timing on blast performance. These trials have demon- strated that delay timing can have a marked influence on blast fragmen- tation, muckpile displacement, blast vibration and airblast.

Jan 1, 1989