Search Documents

By Y Xu, J Hacker, D J. Williams

Shear strength parameters of compacted clay liners are needed to analyse the stability of mine waste dumps containing compacted clay liners as sealing layers for potentially acid forming waste rock. A representative clay sample was supplied by McArthur River Mine from the mine site in the Northern Territory, Australia, with an average as-supplied gravimetric moisture content of about 13.6%. The clay was compacted in a 100 mm by 100 mm direct shear box at the as-supplied moisture content to a dry density of 1.85 t/m3, representing the field compaction specification adopted by the mine. To determine the peak and ultimate shear strengths of the compacted clay, single-stage direct shear testing was carried out at nominal initial normal stresses of 50 kPa, 100 kPa and 200 kPa, representing shallow depths of burial in the North Overburden Emplacement Facility of about 2.8 m, 5.6 m and 11.1 m, respectively (assuming a waste rock wet unit weight of 18 kN/m3). Three shearing rates of 1 mm/min (rapid), 0.1 mm/min (intermediate) and 0.01 mm/min (slow) were applied to study the influence of shearing rate on shear strength. In addition, the development of a residual shear plane was tested by reversal and re-shearing in the direct shear box. In the first shearing, the peak and ultimate shear strengths are determined. The normal load was then removed and the box rewound to its starting position. The normal load was then re-applied and the specimen re-sheared. Two reversals were applied to each specimen, and it was found that there was no significant reduction in shear strength. Finally, based on a range of shear strengths obtained in the laboratory for McArthur River Mine clay and other materials by various laboratories over time, shear strength parameters for the compacted clay were recommended for use by the mine.CITATION:Xu, Y, Williams, D J and Hacker, J, 2018. Shear strength of compacted clay liner at McArthur River Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 208–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By B Ghahreman‐Nejad, M Munro

Design of embankment dams often requires seismic analyses, or an assessment of earthquakeinduced ground and dam movements. There are a large number of cases where earthquakes have triggered sliding and lateral spreading of embankments, resulting in excessive crest settlements. In some instances, liquefaction and embankment failure has occurred resulting in loss of containment. Hence, evaluation of the effects of earthquakes on embankment dams is a critical design aspect. This paper discusses the methods and the results of a seismic liquefaction assessment and deformation analyses of a tailings dam. The tailings dam consists of a perimeter earth core rockfill starter dam which has been raised using upstream construction methods. The embankment raises (formed by an upstream clay blanket and an all-in rockfill body) are constructed over the impounded tailings, which are potentially liquefiable. Extensive field and laboratory tests were undertaken to assess the liquefaction potential of the tailings, and also determine the material properties required for seismic stability and deformation analyses. Numerical modelling of seismic liquefaction and deformation was carried out using FLAC (Itasca 2016) to predict the magnitude and spatial variation of deformations that may lead to an uncontrolled release of tailings. Primarily based on a parametric assessment of UBCSand and Finn-Byrne constitutive models, the results of the analyses are presented and compared for evaluation.

Jul 1, 2021

Bougainville copper concentrate was leached with a strain of Thiobacillus ferrooxidans (SPKI) in a 5 per cent CO2 nitrogen atmosphere.Copper solubilization was 100 per cent in presence of bacteria and only 30 per cent in a sterile acid control medium.Anaerobic copper solubilization rates were one quarter of those measured under aerobic conditions and did not generate acidity.

Jan 1, 1985

By K Biegaj, S C. Dominy

A high-nugget effect and presence of coarse gold characterises many styles of gold mineralisation. The effective sampling of these deposits is often difficult because of the relatively low concentrations involved and erratic nature of the gold or other minerals. Geometric and/or metallurgical complexities often compound this effect. Underground development, in-fill drilling and bulk sampling/trial mining are generally required to delineate Ore Reserves. Similarly expensive definition strategies often apply to surface mining in complex orebodies of gold and other minerals, including precious stones. Development, particularly winzing is a historical technique that was used to gather geological, grade and metallurgical data during underground and near-surface exploration. It permits access to the mineralised structure below the surface datum to determine viability. Winzing has always been considered an arduous and dangerous task. Modern winzing technology has led to the development of the Mobile Supersucker – essentially a giant vacuum cleaner with underground and surface capabilities. By the elimination of shovel-loaded blasted winze material into a kibble and hoisting, this system permits safe and highly efficient winzing activities, and allows the collection of bulk samples for grade and metallurgical evaluation, as well as access to the mineralisation for geological and geotechnical mapping. Bulk samples from horizontal development have long been collected to help define mineable grade via pilot processing. However, when defining blocks below current development, there has been over-reliance on ineffective ‘small sample’ drill data. The Mobile Supersucker permits the development of winzes and off-winze sub-levels. These provide critical information to a mine technical team when trying to justify capital to go deeper or commence or deepen an existing open pit. CITATION: Biegaj, K and Dominy, S C, 2018. Lowering risk in complex mineralisation: application of mobile supersucker development, in Proceedings Complex Orebodies Conference 2018, pp 113–115 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By R Peiffer, L van Wyk

The Port of Port Hedland is the largest bulk export terminal in the world and is one of Australia’s most important pieces of economic infrastructure. BHP is the largest Port user to support the export of iron ore products from mines located within the Pilbara region of Western Australia (WA). BHP’s priority is the safety and well-being of its workforce and the communities where it operates. In a recent regulatory application to increase export capacity, BHP committed to the deployment of wind fences to reduce wind erosion from stockpiled ore. Wind erosion from stockpiles was identified through inverse modelling as the most significant dust source compared to other sources such as stackers, reclaimers, shiploaders and transfer stations. The primary cause of dust emissions from stockpiles is dust lift-off during high wind conditions. BHP proposed the installation of wind fences across its Port Hedland operations, targeted at reducing emissions from wind dependent sources, primarily stockpiles, by reducing the wind speed downwind of the wind fence. Modelling predicts that installation of the wind fence will significantly reduce emissions from stockpiles, particularly at BHP’s western operations (Finucane Island). To be effective in shielding stockyards and reducing wind speeds, the wind fences are located upwind and as close as practical to the open stockyards. BHP’s wind fence design incorporates learnings from other existing installations and has been tailored for Port Hedland’s cyclonic conditions. The wind fence will be higher than the stockpile height, with a mesh porosity of approximately 50 per cent. The mesh porosity allows some of the wind to pass through the mesh. This reduces the wind turbulence downstream of the wind fence, as opposed to a solid wind fence, which increases downwind turbulence, resulting in increased dust.

Sep 18, 2023

By J Kwiri, T Zvarivadza, R Mitra, F Cawood

It is crucial to record ground movement of any magnitude to enable the safe and economical design of excavations and infrastructure. The DigiMine Laboratory is equipped with technologies to record such movements. This paper analyses the effectiveness of the Digital Mine instrumentation in recording earth movements in light of the Botswanan earthquake which occurred on the 3rd of April 2017 at 17:40 UTC. Recordings from the Digital Mine are compared with other ground sensing technologies which also captured the event (USGS and GEOFON systems). USGS and GEOFON system’s recordings suggest that, there are a number of possible mechanisms that could have resulted in the earthquake as discussed in the paper. Compared to the USGS and GEOFON systems, DigiMine system could not provide an analysis that could give possible source mechanisms. However, the system’s success in recording the Botswanan earthquake, is an indication that the system works and can be further developed or improved. For a comprehensive analysis, more data from various sensors needs to be collected. For example, DigiMine connecting to the national seismic monitoring system or to the local mine’s seismic monitoring system. Such connections will enable the development of a better self-analysis system and possibly prediction of future events. More importantly, it will contribute to better understanding of regional seismicity and its potential impact on excavation design. CITATION:Kwiri, J, Zvarivadza, T, Cawood, F and Mitra, R, 2018. How efficient is DigiMine technology in recording earth movements? A look at the Botswanan earthquake, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 414–419 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Cyanidation tests by bottle agitation were conducted on an oxidized lead-silver ore containing approximately 12% Pb and 500 g/t Ag. Over 60% of the silver was leached when the ore was ground to 100% passing 0.15mm, whereas 50-60% of the silver was leached when the ore was only ground to 100% passing 0.5mm. Slurry handling and dewatering at the fine grind size were very difficult due to the high clay content of the ore, however this problem was greatly reduced at the coar- ser grind size. The silver recovery at the fine grind size was very dependent on cyanide solution strength with stronger cyanide sol- utions (containing more than 0.1% NaCN) re- sulting in lower solution silver contents. This was thought to be due to the precipi- tation of leached silver by zinc, which was also leached from the ore by the higher cyanide levels. There was a critical zinc level in solution of approximately 1000ppm, above which the silver recovery fell markedly. Cyanide and lime consumptions for this ore were high (typically 5 kg/t and 40 kg/t respectively), hence the processing of this particular ore by cyanide leaching is un- economic at current silver prices.

Jan 1, 1987

By S Ferguson, G Noble

The mining industry is facing economic pressures to treat more challenging and lower grade ore types, as well as pressure relating to environmental impact and social license to operate. Preconcentration through bulk ore sorting has the potential to benefit all these areas by enabling mining operations to divert material of low economic value prior to processing, thereby achieving higher feed grades and recovery, while reducing the processing plant and tailings dam footprint and capital required throughout the life of mine. The effectiveness of bulk ore sorting depends on the heterogeneity of material at the measurement location, as well as the accuracy and precision of the measurement. An understanding of ore heterogeneity can be assessed using drill core data, which provides metre by metre elemental assays. This paper reviews such data and assesses the grade distributions over different scales, which suggests that sufficient heterogeneity exists at mining scales to allow the potential for bulk ore sorting. Prompt Gamma Neutron Activation Analysis (PGNAA) technology has proven to be a successful measurement technique within many industries, including mining. PGNAA was first developed in the early 1980’s for the measurement of the elemental composition of bulk materials on a conveyor belt. Today, Pulsed Fast Thermal Neutron Activation (PFTNA) technology is also applied in elemental analysis of bulk materials and has some advantages for bulk ore sorting. In order to enable effective bulk ore sorting, however, a PGNAA/PFTNA analyser must be designed to provide a representative bulk ore analysis with the necessary accuracy and precision. Examples are presented to provide an understanding of the factors affecting PGNAA/PFTNA performance in relation to effective bulk ore sorting.

Nov 10, 2020

By M Reid, H Arbon

Hillgrove Resources (HGO) commenced open pit mining in 2011 and from 2011 to 2016 the geology team experienced a consistent negative reconciliation between grade control estimated copper (Cu) grade and the mill received grade. For the first four years, despite trialling various grade control strategies, the monthly variance between geology and mill copper grades fluctuated between -5 per cent to -17 per cent Cu metal depending on the style of mineralisation.In 2015, HGO embarked on various measures which resulted in changes to grade control practices under the advice of consultants. These changes to grade control sampling, estimation and block out practices resulted in six to seven months of consistently poor Mine to Mill reconciliations from -25 per cent to -28 per cent Cu.In an effort to mitigate these poor reconciliations the geology team reintroduced the preconsultant block out and geology driven grade control methods. Blockout reconciliations from this point emulated those seen originally from -8 per cent to -12 per cent (Cu per cent). Early in 2016 the geology team introduced conditional simulation for grade control as opposed to ordinary kriging to better characterise the grade distribution, introduced separate estimation parameters appropriate for every zone of mineralisation, implemented a maximum profit function to optimise the selection of ore and waste, and retained the geology driven block out processes. Since March 2016 the mine has experienced consecutive months of positive Mine to Mill reconciliations, the first seen in six years. Year to date the expected copper metal is within 1 per cent of mill reconciled copper metal.This paper will compare the various sampling methods, estimation algorithms and block out procedures from the past six years to arrive at a robust open pit operating procedure applicable for mineralisation with high short scale variability.CITATION:Reid, M and Arbon, H, 2017. Setting new standards at Kanmantoo – effective grade control procedures, in Proceedings Tenth International Mining Geology Conference 2017, pp 401–408 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By M Hood, X S. L, W J. T Daniel, H Gurgenci

It is believed that disc cutter shape affects rock fracture and therefore cutter performance and cutter life. However, the current generation of disc cutters is made of hardened steel and these cutters wear rapidly and consequently they are unable to maintain their original shape in strong and abrasive rock. This wear problem could be reduced if the cutter was made from a harder material. Unfortunately as material hardness increases so does the propensity for brittle failure. In this study the optimum cutter shapes were identified by studying the mechanics of rock/tool interaction. The results showed that bevel and wedge cutters are better than cutters with dome and flat edges. A new cutter was designed, based on this result, using a harder material to increase the life by a factor of 20.

Jan 1, 1998

Economic evaluations of mineral projects are based on discounted cash flow analyses, followed by sensitivity and risk analyses. However, the global macroeconomic and political environment in which the mineral industries operate have a profound effect on the viability of individual projects. Since the oil crises of 1974 and 1980, demand patterns for minerals have become much more variable and prices more volatile. Significant changes in the geographical distribution of world mineral supply and demand are underway, and the mix of minerals used is also changing. Social and political factors are as important as economic and technical factors in determining the viability of mineral ventures. Economic evaluation of mineral projects have to be undertaken in a more uncertain and risky environment. They can no longer be reduced to a number crunching exercise.

Jan 1, 1987

By S Brunt

A new elution process has been developed for the recovery of gold thiosulfate from ion exchange resins. This is a synergistic system which utilises a base eluent, such as nitrate or trithionate, along with an additive that improves the elution of gold. The use of the additive enables lower eluent concentrations to be adopted, as well as weaker eluents such as chloride. With the chloride + additive system, complete gold elution can be achieved within 12 BV when utilising an eluent flow of 5 BV/h. When the eluent flow is reduced to 2 BV/h, complete elution is achieved within 8 BV. Similar results are obtained when using nitrate or trithionate as the base eluent. A copper pre-elution process has also been developed, whereby the majority of copper can be stripped within 5 BV prior to gold elution. This method is a significant improvement on the ammonia + oxygen pre-elution previously suggested. The development of a new analytical procedure based on ion chromatography with UV detection is also described for the quantification of polythionates in leach solutions and loaded on resins. This enables analysis to be carried out for resin-in- leach type processes where the polythionates are being formed in solution and simultaneously adsorbed onto the resin.

Jan 1, 2007

Australasian mining companies expect a high standard of professionalism from their metals exploration teams. They also have, increasingly, a global perspective, employing explorationists of diverse cultural backgrounds and operating in diverse environments. Human resource development (HRD) of these professional explorationists needs to address all personal facets of functioning independently and interdependently in a modem working culture, as well as the needed technical competency. Creation of a learning organisation to promote this development is critical. Organisational consultants can support managers and supervisors as mentors facing the wide spectrum of development required by the explorationists; mentorship and guidance counselling can then complement training in the maturing of professionals from technical competence to professional independence and interdependence. Empowerment and clearly stated expectations are keys by which professionals can learn efficiently and effectively.

Jan 1, 1996

A novel solvent extraction process, called the SOHNEX process, has been developed at the University of Utah. In this process, the organic and the aqueous phases flow countercurrently in a horizontal vessel, and the emulsion between the two liquid phases is generated by high-velocity gas jets injected at the bottom. The gas jets are located at certain intervals along the bottom of the vessel with phase disengagement zones on either side of the plume zone created by the gas jet. The system is simple, having no mechanical moving parts or complex internal structures, and yet provides good contact between the phases with minimal backmixing. Tests have shown that emulsions with a wide range of specific interfacial area, including that typically encountered in mixer-settlers, can be generated in this process. It has significant built-in flexibility of operation including the control of the flowrate and hold-up of each liquid phase. The SOHNEX process overcomes the difficulties in the operation of conventional solvent extraction equipment such as mixer-settlers and column extractors. A major advantage of the SOHNEX process is that the energy of mixing can be closely controlled by adjusting the strength of the gas jet. This allows an optimal control of the drop-size distribution of the dispersed phase and thus the specific interfacial area. The process is continuous, and any number of extraction and separation stages may be built into a single vessel. The gas can be recirculated in a closed loop, thus eliminating solvent loss and mist problems, especially for high-temperature operations. The SOHNEX problem can handle solutions that contain suspended solids and that form third phases. The simplicity of the equipment and operation with low maintenance will mean much reduced capital and operating costs as well as low environmental risks and improved safety. The SOHNEX process has been tested for continuous copper extraction from a dilute solution. Calculations also showed that uranium and other radioactive elements can readily be extracted in a small unit of the SOHNEX extractor while satisfying the nuclear criticality condition.

Jan 1, 2000

By Angove JE, Johnson GD

Sulphide concentrates are produced in a wide range of mineral processing operations. In the case of base metals they are further treated by smelting and/or hydrometallurgical techniques. In the case of refractory gold ores, sulphide concentrates containing gold are roasted or oxidised by various hydrometallurgical processes. This paper discusses the development of the Activox(R) Process which can provide an alternative method for treating sulphide concentrates. This process consists of fine or ultra-fine milling, followed by mild pressure oxidation to produce solutions of base metals or to liberate refractory gold. Base metal solutions (eg of nickel and cobalt) can be further processed by solvent extraction and electrowinning, while refractory gold can be recovered by cyanidation. The economics of the Activox(R) Process are often better than alternative oxidation techniques.

Jan 1, 1993

By G Pizarro, O Miranda, D Rosales

In panel/block caving mines, large amounts of information are collected at the operations. This information includes grades and extracted tonnage, fragmentation, lithology, design of stopes and main infrastructure, geotechnical information, overbreak progress, seismicity, numerical modelling and many other mine variables. To improve the reliability of the production plan it is required to integrate the mine data into one platform. In this paper, the logic of a new technological platform is presented for analysis, modelling and design in panel/block caving mines. The platform includes an acquisition system for mine data and geotechnical information, a back-analysis module for calibrating statistical models and a module of visualisation of the results. The application and benefits of the platform is illustrated for mining induced seismic risk for panel/block caving mining operation. The platform can be used in the mine design and planning processes and is useful for reducing uncertainty in the mining business of panel/block caving operations.CITATION:Miranda, O, Rosales, D, Pizarro, G and Vallejos, J, 2016. Development of an integrated platform for the analysis, modelling and design in panel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 237–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R Hughes

"Spring Creek Mine uses high pressure water to extract the thick Main seam in the Upper Rewanuicoal measures. The extraction method results in the creation of large voids which collapsespontaneously. This can result in the displacement of large volumes of methane, which may create a signifi cant hazard if not correctly managed. A system of automatic dilution doors is employed to mitigate this risk. This paper describes the evolution of the system and gives some examples of its eff ectiveness."

Jun 1, 2012

By G S. Beros

In 2019 the Chinese Ministry of Ecology and Environment issued guidelines promoting the implementation of ultra-low emissions in the iron and steelmaking industry. These guidelines aim to drive improvements in air quality through the reduction of particulate matter (PM), sulfur dioxide (SO2) and nitrogen oxide (NOx). Secondly, it also represents an initial means to commence decarbonisation of the industry. The ultra-low emissions guidelines propose that well over 80 per cent of China’s production capacity will achieve these targets by 2025. In response, many sintering operations have implemented numerous improvements to the process that result in significant efficiency gains. Of note is the adoption of deep bed sintering where, with some modifications to equipment, the sintering bed depth is increased resulting in sizable reductions of SO2 and NOx emissions. This paper will also provide an overview of the requirements to introduce deep-bed sintering into an operation and highlight test work completed which quantifies the resultant reduction in emissions.

Nov 8, 2021

By N J. Grigg

Gekko Systems has developed an underground pre-concentration plant (Python) to reduce mine operating costs. Many ores liberate favourably using either high pressure grinding rolls (HPGR) or vertical shaft impactors (VSI). Using these comminution circuits for mineral liberation; rather than for the final recovery process and by utilising a high mass pull, high recovery process route (gravity/flotation), a narrow, low head, compact processing plant was developed that can sensibly be operated underground. The Python underground processing plant can provide a number of advantages for narrow vein mines including lower haulage costs, improved mine call factor and lower operating costs. The focus on fine crushing reduces the power requirement of the plant to approximately 8 kWh/tonne. The Python underground processing plant has been designed to be towed down the decline or lowered down a shaft, and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a saving in mining costs and a significantly smaller environmental footprint.

Jan 1, 2008

First of all, I should like to thank you for theopportunity to be with you tonight and tocongratulate the Kalgoorlie and Perth branchesof the Australasian Institute of Mining andMetallurgy in initiating this most importantConference.It could not have been better timed.Gold is riding a crest of the wave, leading theresurgence in the State's mining industry.The strong and stable economic policies whichhave been pursued both by the Burke LabourGovernment in this State and by the HawkeGovernment in Canberra, whilst they have ofcourse only been part of the reason for thestrong recovery in the mining industry - a l o tof it being due t o international factors - havecertainly assisted and ensured that the miningindustry in this state has been able to takefull advantage of the changed world situation.

Jan 1, 1984