Search Documents

By K McNabb, M H. Turner, P A. Jenkin

Mining of the Agnew nickel deposit commenced in 1970 using a variety of underground mining methods, though with mixed success due to the difficult ground conditions. WMC Resources Ltd acquired the operation in 1989, and commenced nickel production with an open pit. In 1995 all production reverted to the rejuvenated underground mine, using exclusively SLC (sublevel caving) methods. Currently the mine produces 1.4 Mt per annum, at an average grade of 1.74 per cent Ni. Underground mining of the Perseverance orebody has always presented significant challenges due to the difficult ground conditions in the weak and altered ultramafic rocks. The range of problems include areas of swelling minerals, intense and extremely weak shear zones, relatively high in situ stress, and in other areas very brittle rocks. Under these conditions rock mechanics input has been and remains a critical element of the mining strategy. Severe ground behaviour difficulties down to a depth of 500 m below surface prompted a review of the mining strategy for the large disseminated nickel orebody, including evaluation of alternative mining methods. However, sublevel caving was ultimately selected as the preferred method, and a re-design of the SLC cross-cut layout followed. A selection of rock mechanics investigations of interest are described, including complex virgin stress measurements, detailed ground behaviour monitoring, and the use of non-linear stress analyses to re-design the mine layout. Subsequent ground behaviour, support design and production scheduling are also described.

Jan 1, 2000

The cost-effectiveness of blasts involving radiating blastholes is cur- rently restricted in the following ways. (a) Significant percentages of potential explosion energy are not being liberated; the collar sections of some charges are being dislocated and/or desensitised by the detonations of adjacent earlier-firing charges. (b) If the minimum charge spacing is too small, detonation of an early- firing charge can initiate an adjacent charge sympathetically, thereby eliminating the benefit of any intended inter-charge delay. (c) The overall distribution of energy is poor. Appreciably better fragmentation would be achieved if current drill- ing patterns were to be replaced by staggered fans/rings having a toe spac- ing : burden ratio of about 4 : 1. This wide-spaced pattern would enable a higher percentage of the potential energy to be released, would reduce the incidence of sympathetic detonation and would provide a superior overall distribution of this liberated energy. If improved fragmentation is not required, the proposed fan/ring design should allow a significant expansion of the blasthole pattern with consequential cost savings in drill- ing, explosives and initiation.

Jan 1, 1988

By Stewart C. A

The Northparkes copper-gold project is being developed in Central Western New South Wales approximately 30 km NNW of the town of Parkes and approximately 350 km west of Newcastle. The project is a joint venture between North Limited (80 per cent) and the Sumitomo Group (20 per cent). North is the manager. The basis of the project is three copper-gold orebodies, the northern two of which are being mined by conventional open cut methods with the third and largest orebody at the southern end of the lease to be mined by block caving. A fourth mineralised body has been identified in the centre of the lease. While further evaluation of this deposit is required it would appear to be amenable to block caving. Oxide caps of gold ore and copper-gold ore over-lie the two northern orebodies. Development commenced with the construction of a carbon-in-pulp (CIP) plant to treat the oxide gold ore. Construction of a flotation plant to treat oxide copper-gold ore and sulphide copper-gold ore is underway. When full-scale operation is achieved late in 1996 the plant will treat 5.0 million tonnes of ore per year of which 1.1 million tonnes will be open cut ore and 3.9 million tonnes will be block cave ore. In terms of annual ore tonnage the underground mine will be the largest metalliferous mine in New South Wales and the second largest in Australia.

Jan 1, 1995

The present-day arrangement of old ( ? ) Palaeozoic and Mesozoic metamorphic rocks in eastern New Guinea lends some support to the concept of tens:konal dilation in Upper Cretaceous to Lower Tertiary time, It appears that the metamorphic core of the Morobe Arc (Glaessner, 1950) could have been rifted from the eastern flank of Cape York Peninsula, and then been carried north-eastward by some unspecified sub-crustal. tangential force. In the early stages of the rift it is thought.that submarine basalts may have extruded up the .'tension .scar and spread across the floor of the opening rift. Thick clastic muddy sediments derived almost exclusively from the rifted block were then spread across the floor of the opening rift. Later ~ertiary lateral movements from east to west along the Markham-Ramu Fault appear to have bent the northern end of the Morobe Arc towards the.east,,causing the intense folding in the sediments of the Aure Trough.

Jan 1, 1962

Managing project exposure and risk has numerous viewpoints, including those of engineers, owners, bankers and insurers. Fewer stakeholders are involved in early stages, though with wider risk management techniques and tools available. The costs and sometimes benefits of the occurrence of risk and uncertainty have different contingent outcomes for different stakeholders. For some, the impact of risk outcomes can be mitigated or managed. Some sectors and stakeholders can manage resources project risks more completely, by choice or by externally imposed forces, opportunities and constraints. The core to resources project risk management lies in the identification and analysis of project risks, the examination of project management risk options and alternatives, and the determination of which risks are able to be controlled, managed or laid off to third parties. Without prior risk identification and knowledge, the wildcard of previously unidentified or unconsidered project risk impact has the potential for fatal impact to one or more stakeholders. A range of case studies is reviewed, from exploration projects to development and operating projects, with relevant learning experiences, from the risk management lessons available from the oil and gas sector as well as the mining sector. For many cases, the emphasis focuses on the risk analysis modus operandi and on risk management and risk mitigation techniques that can be and in some cases have recently been implemented for resources project and related debt, capital markets and equity project fundings.

Jan 1, 2003

The output of Dexin Pit Copper is up to 33 million tonnes a year and the final depth is more than 500 m. As a cost reduction measure, the in-pit crushing and conveying system has was introduced to deliver ore from the pit to mills. This paper describes the in-pit crushing and conveying system, and highlights the optimum level where the shovel-truck haulage system transfers into In-pit Crushing and Conveying system, relocation of an in-pit crushing system, and includes the impact of the transferring point when the costs change.

Jan 1, 2003

Three methods of gold analysis are briefly described highlighting some of the problems and advantages of each. The variation of results between samples and splits and due to method preparation are illustrated. The mean percent difference of the fire assay values from the means of sample split values for three cases is 15%. Finally, a comparison of the aqua regia atomic absorption spectroscopy and fire assay fusion AAS techniques is made. This shows that the mean precision, the ability to obtain the same value, of the methods at 98% confidence are +30% and +15% respectively. The fire assay fusion atomic absorption spectroscopy method is relatively more accurate than the aqua regia method.

Jan 1, 1982

By Chitombo GPF

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have heen identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By G P. F Chitombo

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have been identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

The equipment and general smelter layout for the Mount Isa Copper Smelter were designed by engineers associated with the American Smelting and Refining Company and by Mount Isa staff engineers. The final notice of site was dictated by the need for 'building the smelter near the existing Mount Isa power house to enable full use to be made of the steam from the waste heat boilers. Although much excavation work was necessary before concrete foundations could be poured, the location lends itself to further expansion should it become necessary. The plant is designed and constructed to involve straight line smelting operations which include the following major steps in the overall scheme.1. Charge make-up.2. Roasthig.3. Reverberatory smelting.4. Converting.5. Refining.6. Casting.CHARGE MAKE-UPA system of proportioning bins is provided for preparing the feed mixture for the roasters, Sulphide concentrate containing 24% copper wiil be delivered by belt conveyor from the filter plant to the smelter storage patio. This is a large roofed concrete floor that provides a maximum storage capacity of 8,000 tons of concentrate. Eight proportioning bins located below but adjacent to the south end of the patio will be used for actual charge make-up from which concentrate, ore and flux will be proportioned to the feed belt and conveyed to the roaster feed hoppers. Four of the proportioning bins, 80 tons capacity each, will receive...

Jan 1, 1953

By Lawson F

Arsenic-containing waste was dissolved into molten slags and the leaching behaviour of the quenched arsenic-doped slags (containing up to 2.3 wt per cent arsenic) was ascertained to evaluate the potential of this method as a means for arsenic disposal. The leaching behaviour was evaluated using acetic and sulphuric/nitric acid based solutions.From short-term (18 hour) leach tests, the amounts of arsenic in the leach solutions were found generally to decrease with an increase in the Fe(III)/Fe(total) ratio of the slag or an increase in pH of the leach solution. The amount of arsenic in solution increased with an increase in the slag basicity, the slag arsenic concentration or the surface area of the slag exposed to the leach solution. From longer term leach tests (up to 40 weeks) in the pH range 5 to 8, the arsenic remaining in the leach solution was believed to be controlled by sorption processes. The sorbent was an iron oxide-rich material which had the capacity to lower the arsenic concentration in the leach bottles to well below 1 ppm in some cases. At a leach solution pH over 9, the arsenic concentration in the solution increased with time, although the rate of solubilisation was much slower due to the high pH.Slags have the potential to stabilise arsenic and prevent it entering the environment provided attention is paid to the slag chemical composition and oxygen potential.

Jan 1, 1996

Current mine ventilation systems have evolved from simple, limited energy, series or multi split layouts motivated by low suction, slow running, surface fans. Concentration of coal production from fewer working places and ventilation splits, and varying needs, hazards and challenges, however, have led to substan- tial changes. Modern ventilation systems, therefore, are more complex, sometimes more interdependent on others, more energy intensive, and are founded on the use of multiple airways and greater suction, higher speed surface ventilators and often booster fans. Intensi- fication of output has resulted also in higher gas emission rates, the wide adoption of fire- damp drainage, and sometimes in particular problems such as spontaneous firedamp emissions. Some coal mines are subject to spontaneous outbursts of coal and firedamp. These and related matters and current practices and developments are leading to discernible trends, potential advances, and further changes in Practice.

Jan 1, 1983

By Hansmire WH

The 14.7 km Mt. MacDonald Tunnel beneath Rogers Pass in Canada used both drill-and-blast and machine boring methods. A unique ventilation system provides for diesel operations. The design featured minimum construction support and an unrei.nforced poured concrete lining. The west heading was excavated in a single-stage drill-and-blast operation. The east heading used a TBM top heading with a drill-and-blast keyhole bench. The choice of methods was controlled by varying geology, with up to 1,700 m rock cover. Construction performance and progress are evaluated.

Jan 1, 1987

The bulk and surface chemistry of metal ion hydrolysis and precipitation and the redox chemistry of metal ions, sulphur, and other species is central to an under- standing of flotation. The paper contains a review of general hydrolysis-redox chemistry appropriate to the flotation process, and a model of natural and collector-induced flotation of sulphides is constructed. The practical application of the model to real flotation systems is then explored with a view to better under- standing of the chemistry of selectivity and grade control.

Jan 1, 1984

By Simpson D, Skopakow J

This paper is one of the series of papers relating to the Melbourne Underground Rail Loop and specifically describes the structural and architectural design of Museum Station. Structural arrangement, loads and design methods of the major temporary and permanent works are briefly described for the main station and entrance works. Planning of the station concourse area, booking halls and entrances are described together with the selection of finishes for all above and below ground areas.

Jan 1, 1981

A comparison is made between bord and pillar and longwall coal mining. Longwall mining presents a challenge to raise the level of management and engineering practice. To maintain a competitive position in the world export market, the Australian coal mining industry must continue to use and develop the most advanced, cost benefiting, safe mining systems.

Jan 1, 1987

By Fry P. R

Dragline operations have played a major and successful role in coal mining around the world for more than 30 years. Because of this long history, many of the operating draglines are reaching an age where maintenance and downtime costs are prohibitive, and decisions need to be made to either replace or refurbish them.In the current economic climate, refurbishment is a popular choice and this usually involves major structural repairs above and below the roller circle, together with replacement of the roller circle components. Often, the dragline tub is also replaced by a completely new one.

Jan 1, 1992

Naturally occurring organic plastics have been in use for over 2,000 years. Plastics based on chemically modified organic polymers date back only about 100 years, and those based on synthetic polymers about 50 years. The development of ,these two latter groups up to the present day is outlined, and the basic techniques currently available for polymer-building and modi-fication (blending, copolymerisation, quantitative and qualitative struc-tural control, and'si de-group reactions)-are reviewed.

Jan 1, 1962

Evidence abounds for sea-level change having occurred throughout geological and recent time. Driven by climatic changes, by cycles of glaciation and deglaciations, and by tectonics the position of sea-level relative to the crust has been going up and down since oceans first formed. Rates of these differential movements have been as high as 10 mm/year during the last major deglaciation as sea-level rose by about 150 m in about 15000 years. Tectonic processes can also produce change in sea-level relative to the crust of several mm/year as in, for example, the uplift of the Huon Peninsula in Papua New Guinea. To understand what is happening to sea-level today and what may be happening in the future it is necessary to understand the geological and climatic processes that have caused sea-level to change in the past and the best laboratory for the study of these processes is the geological and geomorphological record. Evidence for observations of sea-level change throughout Late Pleistocene and Holocene time is plentiful in the Australian region. Temporal variability is characterized by a low-stand, at more than 100 m below the present level, at about 20 000-18 000 years ago followed by a rapid rise and transgression of the continental margin up to about 6000 years ago. After this time sea-levels remained within a few metres of their present value but the patterns of change are not everywhere the same. The depth of the low stand at about 18 000 years ago does not appear to have been the same everywhere. Nor does the time at which sea-level first reached its present value appear to have been everywhere the same. The fluctuations about present sea-level during the past 6000 years appear to have been different in different localities. As yet there has not been a wholly satisfactory quantitative explanation for this spatial variability. How much, if any, is indicative of vertical tectonics? How much is the result of the Earth's response to the changing surface loads as mass is exchanged between ice sheets and the oceans? Can any of it be attributed to past changes in global climate? Or are the observations just wrong?

Jan 1, 1990

By Newman H. A

Goldsworthy Mining Limited is currently mining iron ore at an annual rate of 7 million tons from several small orebodies, each of which exhibit wide variations in iron, phosphorus, silica and alumina contents. Each orebody is mined at its average ore reserve grade and therefore mine planning and grade control techniques have had to be tailored to achieve a constant production blend.

Jan 1, 1973