Search Documents

By Tiu C, Sarmiento G, Uhlherr PHT

Fundamental rheological properties of slowly settling mineral slurries are reviewed. Slurry flow is discussed in terms of observed shear stress-shear rate behaviour. Particular emphasis is placed on establishing procedures for scale-up and design. Flow property measure- ments on red mud, a waste product from the Bayer alumina process, are presented and used to illustrate recommended design procedures.

Jan 1, 1978

By Misra A

The development of roadways in underground mines in Autralia is by conventional continuous miner technology. The rate of development achieved using this technology is improved by modifications to this technology using additional equipment such as surge cars or decreasing roof bolting time.Development rates achieved with this technology compare with developing technologies such as high capacity continuous miners, continuous transportation and simultaneous cutting and bolting systems such as the Kemcol Beaver. Pillar dimensions have an effect on the rate of development.'

Jan 1, 1991

The reliable estimation of ore reserves in mineral sand deposits depends on drilling methods and assay techniques that have been specially developed within the industry. Improvement of these techniques is a continuing process, as variations within and between deposits are highlighted during the actual mining operation. Constant monitoring of metallurgical losses along with mineral production allows comparison of mineral tonnages accounted for by mining, with original calculated reserves. A review of ore reserves in the Jerusalem Creek field from scout drilling in the sixties, through mining in the seventies, shows the progression from understatement prior to mining, to the present when more than two thirds of the reserves have been depleted.

Jan 1, 1979

To counter depressed world nickel prices, a continuing effort is being made at Kalgoorlie Nickel Smelter to reduce unit production costs. One major area in which production costs can be reduced is the substitution of coal for fuel oil. Two areas where this has been achieved to bring about a saving are, the addition of coal to flash furnace flux to reduce supplementary fuel oil requirements in flash smelting and the replacement of two oil-fired air preheaters with a coal-fired unit. These actions have resulted in coal replacing 67% of the current fuel oil requirement in flash smelting at the Kalgoorlie .Lckel Smelter.

Jan 1, 1987

This paper summarises the results of a study carried out for the Sustainable Minerals Institute, University of Queensland, aimed at identifying the major water-related issues facing the minerals industry internationally and the research required to support the development of practicable solutions. An overview is given of the sources and uses of the worldÆs water resources and of the regional and global sustainability of water supply and management. Agriculture is the worldÆs major user of water; it wastes more water than the minerals industry uses. Water reform and its potential impact on the minerals industry are discussed with particular reference to Australia and South Africa. The sources, uses and management of water on mine and processing sites are outlined. Particular attention is paid to the importance of groundwater as a source of often saline water that can be used in mineral processing and for other purposes. Aquifer storage and recovery has the potential to help conserve water resources. Generally, the major uses of water on mining and processing sites are for mineral processing and refining and for the associated tailings disposal. Water consumption for these purposes may be reduced by recycling process water, using saline water, paying close attention to water management, thickening tailings and using techniques such as dry stacking and paste. A change in the minerals processing paradigm in respect of water use could come through research into new, improved and less costly dry processing techniques. The treatment of mine and processing water will be required increasingly before water is reused, stored, discharged or sold, and before sites are decommissioned. Research and development are required to reduce costs and develop new treatment methods. Mine closure and decommissioning raise a number of long-term water issues requiring continuing generic and site-specific research and development.

Jan 1, 2003

Drilling and blasting operations have historically been viewed as a necessary 'evil' part of mining, whose costs should be minimised by whatever means possible. In the past, when operations depended primarily on crushing and milling for ore re

Jan 1, 1998

Consideration was given to the.applicab on of a solvent extraction circuit to be'included in the process'for the-recovery of a high grade product from.:-the Rum Jungle Creek.South uranium ore body.The economics of two alternative processes, firstly the Eluex process which uses an ion exchange process followed by solvent extraction.-of a.high grade sulphuric acid eluate, and secondly a process using direct solvent' extractioh of pregnant leach liquor, were studied. There was a small cost advantage favouring the Eluex process but when other factors were considered, the installation of a direct solvent extraction process appeared the better long term investment. A solvent extraction plant was installed at Rum Jungle in 1962.

Jan 1, 1963

By Mahoney M

For gas content analysis in recent years, it has been standard procedure to report results on a 'dry ash free' (daf) basis, under the assumption that gas only adsorbs onto coaly material. In order to test the relationship between ash and sas content, samples of various rock types were taken from two drillholes in the Newcastle Coalfield. The results of this study confirmed the correlation between gas content and ash, providing an accurate means of relating gas contents for all carbonaceous rock types.

Jan 1, 1995

By R Crookes

Mine to mill optimisation is not a recently developed concept. It is one which is finally gaining greater acceptance in the Australian mining industry, possibly as a consequence of the downturn in markets and certainly made possible by the development of tools and techniques to measure and predict performance of mining equipment and milling plants. Fragment size after blasting has a major bearing on the performance of all aspects of mining and a major influence on the economics of the mine and mill. The process to optimise fragmentation consists of identifying the key factors, measuring their sensitivity through a modelling and trialing program and conducting economic evaluations on the changes on both the mine and mill. Management of the Ernest Henry copper-gold mine in Northern Queensland, Australia, has espoused the mine-to-mill concept and is actively pursuing excellence in blasting to drive down the total cost of mining. Ernest Henry has extremely hard, wet and heavily jointed geological conditions, and had high powder factors and a large percentage of oversize material reporting to the crusher or ROM stockpile. A blasting improvement program was undertaken between Ernest Henry Mining, Thiess Contractors and Orica Explosives to optimise the ore size distribution, particularly the oversize component, as a step to reducing production costs. Measures of success included bringing the rock breaker back from double shifts to part-time operation and increasing direct dumping into the crusher from 70 per cent to 92 per cent. Tools and technologies to predict and measure the performance of individual blasts are needed before it is possible to optimise fragmentation or the downstream processes. These include such specialised Orica Explosives tools as SABREX, POWERSIEVE, and POWERLINE and commercially available drill monitors. As important are the more common still and video camera, borehole loggers, measuring tapes, surveying equipment such as face profilers, and a high speed camera if possible. There are many tools which can be applied however it is rarely necessary or possible to use all of them due to time constraints and a point of diminishing returns. The critical point is knowing what the true parameters of the blast were compared to design -only then can the predictive tools be effectively utilised. Stage one of the program has seen gradual improvement as the understanding grew and practices have been implemented resulting in reduced bridging in the crusher, geological mapping with respective blast designs and the oversize component under control. This paper is about a process approach which links tools and technology to understand the fragmentation drivers and then to optimising the size distribution. The continuous improvement program continues . . .

Jan 1, 1999

By Smith T. N, Wild M. B, Elliot B. J

The process of flash smelting of nickel sulphide ores, as practised at the Kalgoorlie Nickel Smelter, is described. The critical variables in the operation of this process are identified. The design of a pilot-scale, turbulent-jet flash reactor which models the essential features of the industrial smelter is described. A report of its operation and application to an investigation of the ignition of particles of sulphide species is given.

Jan 1, 1991

By D Kent, J Kirkpatrick

The mining industry has long wanted a single communication back bone to cover the majority of their requirements underground. The convergence of communication technologies in the office/surface environment has been identified by the mining industry as a means to achieve their long-standing goal. In particular use of Internet Protocol (IP) systems are seen as proving a basis for a mineÆs communication infrastructure. This paper presents the development philosophy and work undertaken by Inco Limited in Canada, as well as the implications of this on suppliers to enable the technology to be mine worthy and readily available.

Jan 1, 2005

By Singer RP

The Latrobe Valley brown coal deposits are one of Australia's major energy resources with measured and indicated reserves amounting to some 162 billion tonnes. Economically recoverable reserves are estimated at some 65 billion tonnes, 47 billion tonnes of which are classified as available for mining (VBCC (1983)). These deposits contain one of the lowest grade fuels used anywhere in the world. Typical Net Wet Specific Energy values range from 6 to 9 MJ/kg. Despite the low energy value of the raw coal, the Latrobe Valley deposits represent approximately 90% of Victoria's indigenous non-renewable energy resources. Utilisation of this vast primary energy resource has been a key factor in the economic development of Victoria.

Jan 1, 1990

Heavy media separation serves to upgrade mill feed and reduce unit operating costs, allowing ores to be mined which could other wise be uneconomic. At the Aberfoyle mine at Rossarden in north-east Tasmania, a simple heavy media operation using a converted Akins screw classifier as a separating vessel, removes barren quartz from mineralised material. At the Cleveland mine at Luina on the west coast of Tasmania a more complex ore mix requires a versatile operation combining hydro-dynamic and static separation equipment to provide an efficient beneficiation circuit. The two operations are briefly described with a background of basic heavy media separ- ation practice.

Jan 1, 1978

By Kershaw MG

At the Risdon plant of the Electrolytic Zinc Company of Australasia Limited, impurities toxic to the electrolytic production of zinc metal, notably arsenic and antimony, have traditionally been coprecipitated when precipitating iron as ferric hydroxide. With the development of a new lead/zinc mine at Elura, New South Wales, it was anticipated that the concentration of impurities, particularly arsenic, in the zinc sulphide concentrates treated at Risdon would increase. This suggested that an increase in the capacity of the iron purification step in the Risdon plant would be required to cope with the higher input of these impurities.Laboratory investigations showed that the additional capacity would be achieved, either by a massive increase in the amount of iron used as the "collector" in the process, or by a two-stage process. The latter approach was preferred as an increase in the amount of iron precipitated would lead to much higher operating costs and overloading of the existing equipment.

Jan 1, 1985

The growth of the mining industry around Australia over the last ten years has seen many open cut mines developed on shallow oxide reserves. Most of these have been gold operations, although there are some copper mines in the list, too. Many of these have exhausted their oxide reserves and have made the transition to underground mining to access their deeper sulphide ores. Other operations have reached or are approaching the point where the decision has to be made to go underground or cease mining. This paper discusses the issues involved in making the transition from surface to underground mining. The aim is not to discuss each of the issues exhaustively. This would take a conference in its own right. Nor is it intended to provide a primer on underground mining. Instead the aim is, firstly, to flag the issues which must be addressed when planning to make the transition from surface to underground mining and, secondly, to identify critical aspects of mine development.

Jan 1, 1997

By J G. Petrie, H von Blottnitz

The selection and design of process options to deliver outcomes consistent with sustainable development requires simultaneous consideration of multiple objectives, within a climate of uncertainty û including the environmental and social aspects of technology management in addition to the technical and economic aspects of such. An issue of particular relevance in primary metal production is the deportment of minor and trace components within orebodies, products and wastes and the implications of such deportment for eco-efficiency û in particular, the long-term environmental impact of solid waste management practices. The identification of opportunities to enhance recovery of valuable by-products and simultaneously improve the environmental acceptability of final waste output requires a clear understanding of the distribution of the relevant ore components, which results from the choice of processing route and unit operation efficiency. This is challenging, given that process streams generated during primary metal production are generally poorly characterised and the behaviour and deportment of trace to minor and trace components is not well understood. This paper demonstrates how current data gaps and inconsistencies can be systematically addressed through the meaningful reconciliation of empirical plant data with a fundamental understanding of the mechanisms and parameters influencing element behaviour and deportment during the formation and subsequent beneficiation of mineral ore deposits. On this basis, quantitative distribution data and a comprehensive and comprehensible inventory of unit process inputs and outputs as a function of ore compositions and processing technology options can be generated, which is consistent with early design stage information requirements, both in terms of detail and accuracy, ie is æfirst-orderÆ in nature. This predictive approach to element distribution during primary metal production provides decision-makers with key information in the early design stages of a project (in terms of developing processes within the context of sustainability), whilst simultaneously guiding further data collection and environmental impact prediction studies.

Jan 1, 2006

By Lunarzewski L, Truong D

Although there are sound principles used in the world recognised methods of gas emission prediction, results based on these methods applied to several Australian longwall extractions have yielded unacceptably high discrepancies. With the development of mining in new seams and at higher rates of extraction, the need has grown for a methodical approach to predicting gas emission levels specifically for local Australian mining conditions. Such an approach is developed from results of recorded emission readings during longwall mining at Appin and Pacific Collieries over the past 6 years.

Jan 1, 1988

An airlift pump is fitted to the screw conveyor of a decanter type centrifuge in order to pump out soft cakes which are difficult to discharge from a standard decanter. The new patented2 design improves separation performance and allows more stable operation, particularly when operating the decanter as a thickener.

Jan 1, 1989

By King ND

This paper presents an economic study comparing two gold recovery processes, zinc precipitation (Merrill-Crowe) and carbon-in-pulp (CIP). Capital, operating, and gold losses costs from an actual CIP plant study are compared to costs developed from a hypothetical Merrill-Crowe process flowsheet. ' Results indicate an overall economic advantage to CIP over Merrill-Crowe for plants processing slurries within the range of the five gold solution grades selected for this study.

Jan 1, 1982

The increasing introduction of high capacity mechanical equipment into the coal mines of New South Wales following. tforld War II brought with it problems of roof support. Rapidly advancing headings in difficult country could not be supported with heavy, close,timbering due to the time involved in installation and the reduction of available' space for the movement of machines. _ The installation of low cost, space saving, rapidly installed roof supports became a necessity if the new mechanical equipment wa-s to be allowed to operate at maximum efficiency. As, a result of experience in the United States of America, the system of roof support using steel reinforcing bolts began to find increasing, popularity in the mechanised mines in this State. From the somewhat'crude methods of in- stallation adopted in some of the, early trials, the practice of roof bolting has advanced into a-highly technical operation, requiring care and skill to ensure optimum results.

Jan 1, 1971